有机硅耐磨透明涂层的固化分析

ＦＴＩＲ、ＴＧ、ＴＢＡ等对有机硅耐磨涂料（有机硅溶胶）的热固化过程研究表明有机硅胶体中缔合羟基间的脱水缩合速率很高；羟基脱水程度与固化温度有关，温度越高，达平衡时羟基的浓度越低，在１０５～１３０℃间羟基的浓度变化最大，加入适当的固化剂，对羟基的脱水交联有促进作用，在较高的固化温度下，反应体系中出现了环氧环异构化产生的酮羰基的吸收峰     

酰化法测定端羟基聚丁二烯羟值的测量不确定度评定

评定了酰化法测定端羟基聚丁二烯羟值的测量不确定度。分析了测量重复性、称量过程及标准物质稳定性等因素所带来的不确定度分量,采用酰化法测定端羟基聚丁二烯羟值的扩展不确定度为0.01mmol/g。     

HTPB／TDI,HDI聚合反应动力学研究

对端羟基聚丁二烯／甲苯二异氰酸酯，端羟基聚丁二烯／己二异氰酸酯甲苯溶液体系进行了反应动力学研究，用基团分析方法计算了相应体系的活化能，并对无催化剂和有催化剂的体系作了比较。结果表明，二丁基二月桂酸象对上述体系有强的催化作用，使体系的活化能降低，反应速度加快。对于对端差基聚丁二烯／甲苯二异氰酸酯体系，无催化剂时前后期反应活化能分别为２９．１ｋＪ／ｍｏｌ、３７．４ｋＪ／ｍｏｌ，有催化剂时前后期反应活化     

利用扭辫分析法对液体丁羟胶固化的研究(Ⅰ)

本工作用扭辫分析(TBA)技术研究了端羟基聚丁二烯(HTPB)-甲苯二异氰酸酯(TDI)体系的固化反应表现动力学,得到了该反应的表观活化能,并用粘度和红外光谱测定作了验证,认为TBA技术用于研究液体橡胶固化问题是一种有意义的方法。     

温度对丁腈羟聚氨酯固化反应及性能的影响

端羟基液体丁二烯-丙烯腈共聚物(简称丁腈羟,以HTBN表示)通常用甲苯二异氰酸酯作固化剂,N,N′-二羟丙基苯胺为链延伸剂经二步法固化成丁腈羟聚氨酯弹性体。本文报导丁腈羟-甲苯二异氰酸酯预聚体和N,N′-二羟丙基苯胺体系中同化温度对同化反应及固化弹性体性能的影响规律。     

醇酸树脂固化过程的FTIR跟踪

本文用FTIR内标法跟踪观察了醇酸树脂的固化过程,选取1600cm~(-1)处的苯环振动峰作内标峰。结果表明,随着固化的进行,不饱和键递减,涂膜的羧基、羟基等含氧基团递增。固化过程的快慢同涂膜厚度有关,它是受氧扩散作用控制的。     

聚氨酯改性不饱和聚酯/色浆复合体系的固化特性

系统研究了聚氨酯改性不饱和聚酯/色浆复合体系的黏度与固化特性,发现随着色浆含量的增加,复合体系的黏度呈递增趋势,但明显低于理论加和值;而复合体系的凝胶时间、表观起始固化温度与表观峰值固化温度随着色浆含量的增加而增加,但表观终止固化温度与固化热焓却降低;随着升温速率的增大,复合体系的特征固化温度均向高温方向移动,但固化热焓基本不变.将升温速率外推至零,可计算出体系的起始固化温度、峰值固化温度以及终止固化温度,从而确定体系的固化工艺.同时基于不同升温速率下的表观峰值固化温度,通过Kissinger方程可计算得到聚氨酯改性不饱和聚酯/色浆复合体系的固化反应表观活化能以及固化反应动力学指前因子.在最佳固化工艺条件下,聚氨酯改性不饱和聚酯树脂/色浆复合涂层的黏附力均在一级以上.     

氨基聚酯树脂固化过程的FTIR跟踪

用FTIR内标法跟踪氨基聚酯树脂的固化过程,选取815cm~(-1)的三嗪环面外振动峰作内标峰,913cm~(-1)处的甲氧基变形振动峰和3500cm~(-1)左右的羟基伸缩振动峰为特征吸收峰。结果表明,随着固化的进行,涂膜的羟基、甲氧基和羧基递减,醚键和羰基递增,说明固化过程是以交联反应为主,伴有自缩合反应和酯化反应的复杂过程。     

热动力学方法测定端羟基聚丁二烯固化反应动力学参数

用热动力学方法对高分子固化反应动力学进行研究,在RD-Ⅰ型热导式自动量热计的基础上,设计了反应器,测定了端羟基聚丁二烯(HTPB)与甲苯二异氰酸酯(TDI)固化反应的动力学参数(表观活化能和反应速率常数),结果与文献值、粘度法和红外光谱法的结果相符。     

几种聚醚胺改性蒙脱土对环氧树脂固化过程的影响

首先制备了五种聚醚胺改性蒙脱土(MMT), 并将这五种聚醚胺改性蒙脱土加入到双酚A 型环氧树脂E51 和聚醚胺D400体系中, 采用差示扫描量热法(DSC)考察了五种聚醚胺改性MMT对环氧树脂升温固化进程的影响. 随后, 优选一种EP/MMT 混合体系即EP/D400-T500-MMT 混合体系, 系统地研究了该体系与纯环氧树脂体系在130, 140, 150 及160 ℃等几个温度下的等温固化过程, 考察了等温固化时间对固化度和固化度变化速率的影响以及固化度与固化度变化速率之间的关系, 并利用Kamal 模型进行拟合计算了固化动力学参数. 研究结果表明, 与纯环氧树脂相比, 几种聚醚胺改性MMT 的固化放热峰均向高温迁移, 同时聚醚胺D400 协同插层MMT 降低了高分子量聚醚胺插层MMT 所导致的环氧树脂DSC 曲线的畸变情况; EP/D400-T500-MMT 混合体系和纯环氧体系的等温固化反应过程符合Kamal 模型;在相同的固化温度下, EP/D400-T5000-MMT 混合体系的反应速率常数k₁ 和k₂ 值以及反应级数m 均比纯EP 体系小, 而反应级数n 以及总反应级数m+n 值比纯EP 体系大, 表明两种聚醚胺协同插层的改性蒙脱土D400-T5000-MMT 的加入降低了环氧体系固化反应速率. 另外, EP/D400-T5000-MMT 混合体系的活化能E_a1 和E_a2 与纯EP 体系的相比也略有升高.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.