Adsorptive stripping voltammetric determination of cobalt in the presence of dimethylglyoxime and cetyltrimethylammonium bromide

A sensitive procedure for determination of micro-traces of Co(II) by adsorptive stripping voltammetry is proposed. The procedure exploits the enhancement of the cobalt peak obtained by use of the system Co(II)–dimethylglyoxime–piperazine-1,4-bis(2-ethanesulfonic acid)–cetyltrimethylammonium bromide. Using the optimized conditions, a detection limit (based on the 3 criterion) for Co(II) of 1.2×10^–11 mol L^–1 (0.7 ng L^–1) was achieved. The calibration plot for an accumulation time of 30 s was linear from 5×10^–11 to 4×10^–9 mol L^–1. The procedure was validated by analysis of certified reference materials and natural water samples.     

Determination of dopamine in synthetic cerebrospinal fluid by SWV with a graphite–polyurethane composite electrode

This work describes an electroanalytical investigation of dopamine using cyclic voltammetry (CV) and the graphite–polyurethane composite electrode (GPU). In CV studies, well-defined redox peaks characterize the oxidation process at the GPU electrode, which is indicative of electrocatalytic effects associated with active sites on the GPU electrode surface. A new analytical methodology was developed using the GPU electrode and square wave voltammetry (SWV) in BR buffer solution (0.1 mol L^–1; pH 7.4). Analytical curves were constructed under optimized conditions (f=60s^–1, E_a=50 mV, E_I=2 mV) and detection and quantification limits of 6.4×10^–8 mol L^–1 (12.1 g L^–1) and 5.2×10^–6 mol L^–1 (0.9 mg L^–1), respectively, were achieved. The precision of the method was checked by performing ten successive measurements for a 9.9×10^–6 mol L^–1 dopamine solution. For intra-assay and inter-assay precisions, the relative standard deviations were 1.9 and 2.3%, respectively. In order to evaluate the developed methodology, the determination of dopamine was performed with good sensitivity and selectivity, without the interference of ascorbic acid in synthetic cerebrospinal fluid, which indicates that the new methodology enables reliable analysis of dopamine.     

Oxidation of ascorbic acid in the presence of phthalocyanine metal complexes. Chemical aspects of catalytic therapy of cancer 2. Catalysis by cobalt octacarboxyphthalocyanine. Reaction products

The products of ascorbic acid oxidation in the presence of cobalt octa-4,5-carboxy-phthalocyanine sodium salt (TPH) were identified. These include the ascorbate radical (A^·), hydroxyl radical (OH^·), and hydrogen peroxide (H₂O₂). The kinetics of accumulation and consumption of the reaction products was studied. For the concentration ranges of ascorbic acid = 0–2.5 ⋅ 10⁻³ mol L⁻¹ and the catalyst C _TPH = 0–3.5 ⋅ 10⁻⁵ mol L⁻¹, the the highest possible concentration of the ascorbate radical is ∼10⁻⁷ mol L⁻¹, the concentration of H₂O₂ is 7 ⋅ 10⁻⁴ (30% of the starting concentration of ascorbic acid) and the concentration of the hydroxyl radical is at most 10⁻⁶ mol L⁻¹.__________Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 2224–2228, October, 2004.     

Anodic stripping voltammetric determination of mercury using multi-walled carbon nanotubes film coated glassy carbon electrode

An electrochemical method for the determination of trace levels of mercury based on a multi-walled carbon nanotubes (MWNT) film coated glassy carbon electrode (GCE) is described. In 0.1 mol L^–1 HCl solution containing 0.02 mol L^–1 KI, Hg²⁺ was firstly preconcentrated at the MWNT film and then reduced at –0.60 V. During the anodic potential sweep, reduced mercury was oxidized, and then a sensitive and well-defined stripping peak at about –0.20 V appeared. Under identical conditions, a MWNT film coated GCE greatly enhances the stripping peak current of mercury in contrast to a bare GCE. Low concentrations of I^– remarkably improve the determining sensitivity, since this increases the accumulation efficiency of Hg²⁺ at the MWNT film coated GCE. The stripping peak current is proportional to the concentration of Hg²⁺ over the range 8×10^–10–5×10^–7 mol L^–1. The lowest detectable concentration of Hg²⁺ is 2×10^–10 mol L^–1 at 5 min accumulation. The relative standard deviation (RSD) at 1×10^–8 mol L^–1 Hg²⁺ was about 6% (n=10). By using this proposed method, Hg²⁺ in some water samples was determined, and the results were compared with those obtained by atomic absorption spectrometry (AAS). The two results are similar, suggesting that the MWNT-film coated GCE has great potential in practical analysis.     

A flow-injection ultrafiltration sampling chemiluminescence system for on-line determination of drug–protein interaction

A flow-injection ultrafiltration sampling chemiluminescence system for on-line determination of cimetidine–bovine serum albumin (BSA) interaction is proposed in this paper. Cimetidine can be oxidized by N-bromosuccinimide (NBS) and sensitized by fluorescein to produce high chemiluminescence emission in basic media. The concentration of cimetidine is linear with the CL intensity in the range 3×10^–7–1×10^–4 mol L^–1 with a detection limit of 1×10^–7 mol L^–1 (3). The drug and protein were mixed in different molar ratios in 0.067 mol L^–1 phosphate buffer, pH 7.4, and incubated at 37 °C in a water bath. The ultrafiltration probe was utilized to sample the mixed solution at a flow rate of 5 µL min^–1. The data obtained by the proposed ultrafiltration flow-injection chemiluminescence method was analyzed with Scrathard analysis and a Klotz plot. The estimated association constant (K) and the number of the binding site (n) on one molecule of BSA by Scrathard analysis and Klotz plot were 3.15×10⁴ L mol^–1 and 0.95, 3.25×10⁴ L mol^–1 and 0.92, respectively. The proposed system proved that flow-injection chemiluminescence analysis coupled with on-line ultrafiltration sampling is a simple and reliable technique for the study of drug–protein interaction.     

Adsorptive stripping voltammetric determination of 1-(4′-bromophenyl)-3,3-dimethyltriazene

The optimum conditions were established for the determination of the genotoxic substance 1-(4-bromophenyl)-3,3-dimethyltriazene by differential-pulse voltammetry at a hanging mercury drop electrode in the concentration range 1 × 10^–4 to 1 × 10^–7 mol dm^–3. The sensitivity of the determination can be improved through adsorptive accumulation of the investigated substance on the surface of the hanging mercury drop electrode: differential pulse adsorptive stripping voltammetry can be used in the concentration range 1 × 10^–7 to 2 × 10^–10 mol dm^–3. The relative standard deviation (for ten determinations at 2 × 10^–10 mol dm^–3) was 7.5%.     

Micro-pumping flow system for spectrophotometric determination of anionic surfactants in water

A novel procedure has been developed for spectrophotometric determination of anionic surfactants in water using a solenoid micro-pump as fluid-propulsion device. The proposed method is based on substitution of methyl orange (MO) by anionic surfactants in the formation of an ion-pair with the cetyl pyridine ion (CPC⁺) at pH 5.0. The flow network comprised four solenoid micro-pumps which, under microcomputer control, enabled sample and reagent introduction, and homogenisation in the reaction zone. The system is flexible and simple to operate and control, and sensitive and precise. The analytical plot for the anionic surfactant was linear between 1.43×10^–6 and 1.43×10^–5 mol L^–1 (0.5 to 5.0 mg L^–1; R=0.997, n=5). The relative standard deviation was 0.8% (n=11) for a sample containing 5.74×10^–6 mol L^–1 (2 mg L^–1) surfactant. The limit of detection was 9.76×10^–8 mol L^–1 (0.034 mg L^–1) and the sampling throughput was 60 determinations per hour. The results obtained for washing-water samples were comparable with those obtained by use of the reference method, and no significant differences at the 95% confidence level were observed.     

Mercury-free sono-electroanalytical detection of lead in human blood by use of bismuth-film-modified boron-doped diamond electrodes

We report the electroanalytical determination of lead by anodic stripping voltammetry at in-situ-formed, bismuth-film-modified, boron-doped diamond electrodes. Detection limits in 0.1 mol L^–1 nitric acid solution of 9.6x10^–8 mol L^–1 (0.2 ppb) and 1.1x10^–8 mol L^–1 (2.3 ppb) were obtained after 60 and 300 s deposition times, respectively. An acoustically assisted deposition procedure was also investigated and found to result in improved limits of detection of 2.6×10^–8 mol L^–1 (5.4 ppb) and 8.5×10^–10 mol L^–1 (0.18 ppb) for 60 and 300 s accumulation times, respectively. Furthermore, the sensitivity obtained under quiescent and insonated conditions increased from 5.5 (quiescent) to 76.7 A mol^–1 L (insonated) for 60 s accumulation and from 25.8 (quiescent) to 317.6 A mol^–1 L (insonated) for 300 s accumulation. Investigation of the use of ultrasound with diluted blood revealed detection limits of the order of 10^–8 mol L^–1 were achievable with excellent inter- and intra-reproducibility and sensitivity of 411.9 A mol^–1 L . For the first time, electroanalytical detection of lead in diluted blood is shown to be possible by use of insonated in-situ-formed bismuth-film-modified boron-doped diamond electrodes. This method is a rapid, sensitive, and non-toxic means of clinical sensing of lead in whole human blood.     

Electrochemical behavior of a covalently modified glassy carbon electrode with aspartic acid and its use for voltammetric differentiation of dopamine and ascorbic acid

Aspartic acid was covalently grafted on to a glassy carbon electrode (GCE) by amine cation radical formation in the electrooxidation of the amino-containing compound. X-ray photoelectron spectroscopic (XPS) measurement and cyclic voltammetric experiments proved the aspartic acid was immobilized as a monolayer on the GCE. Electron transfer to Fe(CN)₆^4– in solution of different pH was studied by cyclic voltammetry. Changes in solution pH resulted in the variation of the charge state of the terminal group; surface pK_a values were estimated on the basis of these results. Because of electrostatic interactions between the negatively charged groups on the electrode surface and dopamine (DA) and ascorbic acid (AA), the modified electrode was used for electrochemical differentiation between DA and AA. The peak current for DA at the modified electrode was greatly enhanced and that for AA was significantly reduced, which enabled determination of DA in the presence of AA. The differential pulse voltammetric (DPV) peak current was linearly dependent on DA concentration over the range 1.8×10^–6–4.6×10^–4 mol L^–1 with slope (nA mol^–1 L) and intercept (nA) of 47.6 and 49.2, respectively. The detection limit (3) was 1.2×10^–6 mol L^–1. The high selectivity and sensitivity for dopamine was attributed to charge discrimination and analyte accumulation. The modified electrode has been used for determination of DA in samples, in the presence of AA, with satisfactory results.     

Pharmacokinetic detection of penicillin excreted in urine using a totally internally reflected resonance light scattering technique with cetyltrimethylammonium bromide

A quantitative analysis method for penicillins including ampicillin (AmP), benzyl penicillin (BP), oxacillin (OA) and amoxycillin (AmO) is proposed that makes use of the totally internally reflected resonance light scattering (TIR-RLS) signal from the penicillin at the H₂O/CCl₄ interface in the presence of cetyltrimethylammonium bromide (CTMAB), and enables the pharmacokinetics of penicillin taken orally and excreted through urine to be monitored. Penicillin is coadsorbed with CTMAB at the H₂O/CCl₄ interface in neutral solution, resulting in the formation of ion associates that display greatly enhanced TIR-RLS signals (maximum at 368–372 nm). This enhanced TIR-RLS intensity was found to be proportional to the penicillin concentration over the range 0.2×10^–6 to 2.2×10^–6 mol L^–1, with limits of determination (3) of 5.0×10^–8 to 7.0×10^–8 mol L^–1. Pharmacokinetics studies performed using the present method show that the excretion of orally-taken ampicillin through urine has a half-time of 1.05 h and an excremental quantum over 8 h of 49.3%, respectively.     

Synthesis,thermodynamic properties and kinetics of the acid-catalyzed dissociation of nickel(II) diamido polyamino complexes

The ligands 1,10-N,N-bis(2-hydroxymethylbenzoyl)-1,4,7,10-tetraazadecane (L₁) and 1,11-N,N-bis(2-hydroxymethylbenzoyl)-1,4,8,11-tetraazaundecane (L₂) have been synthesized. The stability constants of Ni^II complexes of ligands L₁ and L₂ have been studied at 25 °C using pH titrations. The kinetics of general acid (HCl, 0.04–2.34 mol dm^–3) or buffer (DEPP or DESPEN, 0.05 mol dm^–3, pH 4.83–5.72)-catalyzed dissociation of these Ni^II complexes have been investigated at 25 °C using a stopped-flow spectrophotometer. The ionic strength of solution was controlled at I = 2.34 mol dm^–3 (KCl + HCl) and I = 0.1 mol dm^–3 (KNO₃, buffer), respectively. The kinetic dissociation of Ni^II complexes catalyzed by HCl obeys the equilibrium k _obs = k _1d + k _2H[H⁺], whereas in buffer solution the observed rate constant k _obs = k _d + k _1H[H⁺]. At pH < 1.5, both the proton-assisted and direct protonation pathways contribute to the rates, whereas solvation is the dominant pathway at pH > 6. In the 4.8–5.7 pH range, the complexes dissociate mainly through a proton-assisted pathway.     

Voltammetric determination of traces of cobalt(II) with a chemically modified carbon paste electrode

Summary A new preconcentration and voltammetric determination method for cobalt(II) in aqueous solution with a chemically modified electrode is proposed. The accumulation behaviour and voltammetry of cobalt(II) has been investigated with a carbon paste electrode modified with cationexchanger and 1,10-phenanthroline. The electrochemical response is characterized with respect to carbon paste composition, pH, preconcentration time, cobalt(II) concentration and other variables. For a 3-min preconcentration time, the electrode gives good linearity for 1×10^–7 to 4×10^–6 mol/l Co(II), a detection limit of 8×10^–8 mol/l. The response can be reproduced with a 4.0% relative standard deviation. The method is fairly free from many coexisting ions interferences. A rapid and convenient renewal procedure allows the use of a single electrode in multiple analytical determinations over several days. Satisfactory results are obtained for the determination of cobalt in a variety of certified standard reference materials.     

Cholinesterase sensors based on screen-printed electrodes for detection of organophosphorus and carbamic pesticides

Cholinesterase sensors based on screen-printed electrodes modified with polyaniline, 7,7,8,8-tetracyanoquinodimethane (TCNQ), and Prussian blue have been developed and tested for detection of anticholinesterase pesticides in aqueous solution and in spiked grape juice. The influence of enzyme source and detection mode on biosensor performance was explored. It was shown that modification of the electrodes results in significant improvement of their analytical characteristics for pesticide determination. Thus, the slopes of the calibration curves obtained with modified electrodes were increased twofold and the detection limits of the pesticides were reduced by factors of 1.6 to 1.8 in comparison with the use of unmodified transducers. The biosensors developed make it possible to detect down to 2×10^–8 mol L^–1 chloropyrifos-methyl, 5×10^–8 mol L^–1 coumaphos, and 8×10^–9 mol L^–1 carbofuran in aqueous solution and grape juice. The optimal conditions for grape juice pretreatment were determined to diminish interference from the sample matrix.Abbreviations ChE Cholinesterase - TCNQ 7,7,8,8-Tetracyanoquinodimethane - ChO Choline oxidase - AChE Acetylcholinesterase - BChE Butyrylcholinesterase - BSA Bovine serum albumin - 2-PAM 2-Pyridine aldoxime methiodide     

Simultaneous determination of <Emphasis Type="SmallCaps">L</Emphasis>-arginine and its mono- and dimethylated metabolites in human plasma by high-performance liquid chromatography–mass spectrometry

A simple, fast, sensitive, and reproducible isocratic liquid chromatography–mass spectrometry (LC-MS) method coupled with an atmospheric pressure chemical ionization (APCI) interface for simultaneous separation and determination of L-arginine (ARG) and its methylated metabolites, N-monomethyl-L-arginine (MMA), N^G,N^G-dimethylarginine (asymmetric dimethyl arginine, ADMA), and N^G,N^G-dimethylarginine (symmetric dimethyl arginine, SDMA), in human plasma is presented. Sample pretreatment is not required other than deproteinization with 5-sulfosalicylic acid (5-SSA). Satisfactory chromatographic separation was achieved on a 2.0×150-mm Shimadzu VP-ODS column by using a mobile phase consisting of water/acetonitrile (90/10, v/v) containing 0.5% trifluoroacetic acid (TFA). Positive selective ion monitoring (SIM) mode was chosen for quantification of each analyte. The positively protonated molecular ions [M+H]⁺ of ARG, MMA, ADMA, and SDMA were monitored at m/z 175, 189, 203, and 203, respectively. L-Homoarginine was used as the internal standard (IS) for the assay. The limits of quantification (LOQs) were found to be 1.0 mol L^–1 for ARG, and 0.2 mol L^–1 for MMA, ADMA, and SDMA. The inter-assay precision and accuracy were in the range of 1.8–4.9% and –3.0–5.0%, respectively. The intra-assay precision and accuracy were in the order of 1.7–4.6 and –2.6–4.0%, respectively. The recoveries were between 90.0 and 106.6%. The levels of ARG, MMA, ADMA, and SDMA in human plasma were also determined using the developed method.     

Voltammetric study of glibenclamide at carbon paste and Sephadex-modified carbon paste electrodes

The oxidative behaviour of the antidiabetic agent glibenclamide on a bare carbon paste electrode (CPE) and a Sephadex-modified carbon paste electrode (SMCPE) was explored by cyclic and differential pulse voltammetry (DPV). The analysis procedure consisted of an open circuit accumulation step in stirred sample solution of Britton-Robinson buffer (0.04 mol L^–1, pH 2.0). This was followed by medium exchange to a clean solution of Britton-Robinson buffer (0.04 mol L^–1, pH 5.0), and subsequently an anodic potential scan was effected to obtain the voltammetric peak. The glibenclamide oxidation peak current obtained by DPV was proportional to the concentration of the glibenclamide in the range of 1.0×10^–9 mol L^–1 to 5.0×10^–8 mol L^–1 for 180 s accumulation time, with a detection limit of 4.0×10^–10 mol L^–1. A method was developed for the determination of glibenclamide in formulation and spiked human serum. Moreover, the proposed procedure was used to estimate the serum concentrations after oral administration of a 5 mg tablet of glibenclamide to three diabetic subjects.     

Determination of Trace of Cobalt in Complex Matrices by Adsorptive Stripping Voltammetry at a Lead Film Electrode

An adsorptive stripping voltammetric procedure for the determination of cobalt in a complex matrices at an in situ plated lead film electrode was described. The procedure exploits the enhancement effect of a cobalt peak observed in the system Co(II)–nioxime–piperazine‐1,4‐bis(2‐ethanesulfonic acid)–cetyltrimethylammonium bromide. The calibration graph was linear from 5×10^?10 to 2×10^?8 mol L^?1 and from 1×10^?10 to 1×10^?9 mol L^?1 for the accumulation times 120 and 600 s, respectively. The detection limit (based on the 3 σ criterion) for Co(II) following accumulation time of 600 s was 1.1×10^?11 mol L^?1. The interference of high concentrations of foreign ions and surfactants was studied.     

Capillary zone electrophoresis for simultaneous determination of seven nonsteroidal anti-inflammatory drugs in pharmaceuticals

A simple capillary zone electrophoresis (CZE) method has been developed for analyzing seven nonsteroidal anti-inflammatory drugs (NSAIDs)—sulindac (SU), ketoprofen (KE), indomethacin (IN), piroxicam (PI), nimesulide (NI), ibuprofen (IB), and naproxen (NA). The separation was run using borate buffer (60 mmol L^–1, pH 8.5) containing 13% (v/v) methanol at 20 kV, and detected at 200 nm. Several conditions were studied, including concentration and pH of borate buffer, methanol percentage, and separation voltage. In method validation, the calibration plots were linear over the range 40.0–500.0 mol L^–1. In intra-day and inter-day analysis, relative standard deviations (RSD) and relative errors (RE) were all less than 5%. The limits of detection were 10 mol L^–1 for SU, IN, PI, and 20 mol L^–1 for KE, NI, IB, NA (S/N = 3, sampling 6 s by pressure). All recoveries were greater than 95%. This method was applied to the quality control of six NSAIDs in pharmaceuticals using NI as internal standard (IS). The assay results were within the labeled amount required by USP 25.     

Preconcentration of transition metal ions from ethanol solution onN-acyl-N′-benzoylthiourea — Modified silica gel

Silica gel was chemically modified with anN-acyl-N-benzoylthiourea group. This material behaved as a selective means of preconcentrating Cu(II), Zn(II) and Cd(II) from ethanol by the column technique. Ethanolic solutions having 6 mol of the metal ions were percolated through the column and retentions of 100% were achieved for all metals. Zinc and copper were eluted quantitatively from the column bed with 5mL of ethanolic O.1molL^–1 (for Zn) and 0.9 mol L^–1 (for Cu) citric acid. Cadmium was recovered totally with 60 mL of ethanolic 2.0 mol L^–1 citric acid. The modified silica was shown to be chemically stable after various adsorption-elution cycles (at least twenty).     

Determination of traces of iron with the catalytic maximum wave in differential pulse polarography

Summary A differential pulse polarographic method for the determination of iron employing the catalytic maximum wave has been studied. A well-defined differential pulse polarographic peak for iron(III) in Britton-Robinson buffer solution containing 50 mol/l N-(2-hydroxyethyl) ethylenediamine N,N,N-triacetic acid (HEDTA) and 5 mmol/l KBrO₃ is observed in the potential range from +0.2 to –0.3 V vs. SCE. The peak current is very large compared to that of the Fe(III)/EDTA complex, being proportional to the concentration of iron(III) between 1.00×10^–8 and 3.58×10^–6 mol/l under optimum conditions. The relative standard deviations for 3.58×10^–7 mol/l and 1.79×10^–6 mol/l iron(III) were 1.38 and 0.54%, respectively (n=5), and the calculated detection limit was 5.2×10^–9 mol/l iron(III). The method has been applied to the determination of iron in fresh snow and rain waters.

---

Spurenbestimmung von Eisen mit Hilfe der katalytischen Maximumsstufe in der Differential-Puls-Polarographie

Zusammenfassung Das Verfahren beruht auf der Tatsache, daß in Britton-Robinson-Puffer (mit 50 mol/l HEDTA und 5 mmol/l KBrO₃) im Potentialbereich von +0,2 bis –0,3 V gegen SKE ein gut definierter puls-polarographischer Peak für Eisen(III) auftritt. Der Peakstrom ist im Vergleich zu dem des Fe(III)/EDTA-Komplexes sehr groß und ist unter optimalen Bedingungen im Konzentrationsbereich von 1,00·10^–8 bis 3,58·10^–6 mol/l der Eisen(III)-Konzentration proportional. Die relative Standardabweichung beträgt 1,38% bzw. 0,54% (n=5) für 3,58·10^–7 mol/l bzw. 1,79·10^–6 mol/l Fe(III). Die berechnete Nachweisgrenze liegt bei 5,2·10^–9 mol/l Fe(III). Das Verfahren wurde zur Eisenbestimmung in Schnee- und Regenwasser eingesetzt.

---

---

This work was supported in part by a Grant-in-Aid for Scientific Research from Hokkaido-prefecture, 1982.     

Molecular Imprinting-Chemiluminescence Determination of Norfloxacin Using a Norfloxacin-Imprinted Polymer as the Recognition Material

A selective molecular imprinting-chemiluminescence method was developed for the determination of norfloxacin by using a norfloxacin-imprinted polymer as recognition material and the Ce(IV)-sodium sulfite-norfloxacin chemiluminescence reaction as the detection system. The chemiluminescence intensity responded linearly to the concentration of norfloxacin within 1.0×10^–71.0×10^–5molL^–1 with a detection limit of 3×10^–8molL^–1. The relative standard deviation for 5.0×10^–7molL^–1 norfloxacin solution was 2.4% (n = 7). This method was applied to the determination of norfloxacin in urine samples, and the results obtained were satisfactory.