Cu-SSZ-13/堇青石整体式催化剂的原位合成及其NH3选择性催化还原NO性能

采用水热合成技术, 在堇青石蜂窝陶瓷载体上原位合成了SSZ-13分子筛, 并借助X射线衍射(XRD)和场发射扫描电子显微镜(FESEM)等手段对其进行表征. 在此基础上, 研究了合成时间对催化剂结构和机械性能的影响. 另外, 使用固定床反应器测试了离子交换度为50%的Cu-SSZ-13/堇青石催化剂和Cu-SSZ-13催化剂水热老化前后的氨气选择性催化还原(NH₃-SCR) NO性能. 结果表明, 通过原位合成法制备的Cu-SSZ-13/堇青石催化剂在200-500 ℃ 的窗口温度内能达到80%以上的转化率, 并在300 ℃ 时达到96.4%的转化率. 在850 ℃水热老化12 h后, Cu-SSZ-13催化剂完全丧失了催化性能, 而Cu-SSZ-13/堇青石催化剂在300 ℃时仍然保持91%的转化率. 使用XRD和固体27Al 核磁共振(²⁷Al NMR)的方法, 研究了水热老化前后两种催化剂结构的变化, 结果表明, 当水热老化12 h 后, Cu-SSZ-13 基本丧失了SSZ-13 结构特征峰, 而Cu-SSZ-13/堇青石仍然保持了一定的SSZ-13 骨架结构. 证明了通过原位合成法制备的Cu-SSZ-13/堇青石催化剂具有较好的抗水热老化性能.     

整体式堇青石负载的Cu-SSZ-13分子筛催化剂的制备及其氨选择性催化还原脱硝性能

以聚乙烯醇（PVA）或拟薄水铝石（SB粉）为涂覆助剂，采用超声波辅助分散法将Cu-SSZ-13分子筛涂覆于蜂窝状堇青石（Cordierite）上，制备了整体式堇青石负载的Cu-SSZ-13分子筛催化剂（Cu-SSZ-13/Cordierite），用于氨选择性催化还原（NH₃-SCR）脱硝，并结合XRD、氮气吸附、SEM及H₂-TPR等表征手段，研究了涂覆助剂对该催化剂的Cu-SSZ-13涂层稳定性、NH₃-SCR脱硝活性、水热稳定性和抗SO₂毒化能力的影响。结果表明，以PVA为涂覆助剂制备的整体式Cu-SSZ-13（PVA）/Cordierite催化剂，其Cu-SSZ-13涂层稳定、脱落率低，选择性催化还原脱硝活性与Cu-SSZ-13原粉基本相当；同时，该Cu-SSZ-13（PVA）/Cordierite催化剂也具有较好的耐高温水热稳定性和抗硫中毒能力，在移动源和固定源脱硝方面有较好应用前景。     

一步水热合成Cu-SSZ-13分子筛选择性催化C3H6还原NO

采用铜胺配合物(Cu²⁺-四乙烯五胺,Cu-TEPA)作为结构导向剂,通过一步水热法合成不同铜铝比(n_Cu/n_Al)和硅铝比(n_Si/n_Al)的Cu-SSZ-13分子筛催化剂,研究其在贫燃条件下丙烯选择性催化还原NO(C₃H₆-SCR)的性能。当n_Cu/n_Al=2、n_Si/n_Al=6时2.0Cu-SSZ-13(6)催化剂具有最好的低温脱硝活性,200℃时NO转化率超过80%,在250~300℃可实现100%脱硝效率和~100%N₂选择性,同时具有较强的抗水、抗硫性能。为研究不同n_Cu/n_Al和n_Si/n_Al对催化剂物理化学特性的影响,通过X射线衍射(XRD)、扫描电子显微镜(SEM)、N₂吸附-脱附测试、H₂程序升温还原(H₂-TPR)、氨气程序升温脱附(NH₃-TPD)、紫外可见光谱(UV-Vis)等手段对样品进行表征。结果表明,2.0Cu-SSZ-13(6)具有最佳的脱硝性能,这是因为其具有最大的比表面积、最强的表面酸性和分布最多的孤立态Cu²⁺离子。Cu-SSZ-13上丰富的酸性位可以有效促进C₃H₆和NO的吸附和活化,SSZ-13分子筛八元环中孤立的Cu²⁺离子具有良好的氧化还原性能,是C₃H₆-SCR反应的主要活性位。随着n_Cu/n_Al的增加,孤立的Cu²⁺离子会在分子筛表面迁移、集聚形成CuO物种,从而导致C₃H₆-SCR活性下降。     

微波辐射法制备Cu-SSZ-13催化剂及其对柴油车尾气NOx的脱除

采用微波辐射法和传统水热法分别制备了Cu-SSZ-13催化剂,用于柴油车尾气NO_x的脱除.用X射线衍射(XRD)、N₂物理吸脱附、H₂程序升温还原(H₂-TPR)、电子顺磁共振(EPR)、NH₃程序升温脱附(NH₃-TPD)、电感耦合等离子体质谱(ICP-MS)及X射线光电子能谱(XPS)等方法对样品进行表征.结果表明,微波辐射法大大缩短了SSZ-13分子筛的晶化时间,晶化9 h制得样品的结晶度与传统水热法晶化72 h制得样品的结晶度相近,同时孔结构参数也得到了一定程度的改善,微波辐射法制备样品的Brönsted(B)酸性位和Lewis(L)酸性位增多,活性组分铜的负载量也得到显著的提高,使得微波辐射法制备的催化剂呈现出优异的低温活性和水热稳定性.     

Designed copper-amine complex as an efficient template for one-pot synthesis of Cu-SSZ-13 zeolite with excellent activity for selective catalytic reduction of NOx by NH3

Low-cost copper-amine complex was rationally designed to be a novel template for one-pot synthesis of Cu-SSZ-13 zeolites. Proper confirmation and appropriate size make this complex fit well with CHA cages as an efficient template. The products exhibit superior catalytic performance on NH(3)-SCR reaction.     

Two different cationic positions in Cu-SSZ-13?

H(2)-TPR and FTIR were used to characterize the nature of the Cu ions present in the Cu-SSZ-13 zeolite at different ion exchange levels. The results obtained are consistent with the presence of Cu ions at two distinct cationic positions in the SSZ-13 framework.     

由新型铜胺络合物模板剂设计合成活性优异的Cu-SSZ-13分子筛

以低廉的铜胺络合物为新型模板剂, 成功地合成了含铜的 SSZ-13 沸石分子筛 (Cu-ZJM-1). 在合成过程中, 铜胺络合物既是模板分子, 又是催化活性组分铜物种的直接来源. 理论计算表明, 该模板分子的构型与尺寸恰好与构成 SSZ-13 分子筛结构的 CHA 笼相匹配, 因而可以成功地导向该沸石分子筛结构. 采用 X 射线衍射、扫描电镜、氮气吸附、红外、紫外-可见吸收光谱、差热-热重分析、氨气程序升温脱附及氢气程序升温还原等手段对样品的性质及模板分子的状态进行了系统表征. 结果表明, 所制 Cu-ZJM-1 样品为结晶度很高的 SSZ-13 沸石结构, 硅铝比和铜负载量可调且铜处于高分散状态, 在 NH3 选择催化还原氮氧化物反应中表现出优异的催化性能.     

原位合成的Cu-SSZ-13催化剂：结晶时间对NH3-SCR性能的影响

通过一步法原位合成Cu-SSZ-13分子筛催化剂,考察了结晶反应时间对NH3选择性催化还原(NH3-SCR)催化性能的影响,利用H2程序升温还原(H2-TPR)、X射线衍射(XRD)、电子顺磁共振光谱(EPR)和X射线电子能谱(XPS)等分析手段表征催化剂。结果表明,结晶时间不同会影响到Cu-SSZ-13分子筛中活性Cu物种的含量和分布,结晶时间为4 d时Cu-SSZ-13分子筛的NH3-SCR催化性能最佳。高温水热条件下,Cu-SSZ-13分子筛中不稳定的Cu~(2+)A物种会发生迁移而形成相对稳定的Cu~(2+)B物种;Cu~(2+)物种发生团聚而造成分子筛结构破坏,部分Cu~(2+)物种也因分子筛骨架坍塌而被包埋,这是导致催化活性下降的主要原因。     

Catalytic transformation of methane over in-loaded ZSM-5 zeolite in the presence of ethene

Methane is shown to react with ethene over In-loaded ZSM-5 to higher hydrocarbons such as propene and toluene at around 673 K. Such methane conversion is not catalyzed by proton-exchanged ZSM-5 (H-ZSM-5) under the same conditions, only C2H4 being converted to higher hydrocarbons. By using 13C-labeled methane (13CH4) as a reactant, the reaction paths for the formation of propene, benzene and toluene were examined. 13C-labeled propene (13CC2H6) is formed by the reaction of 13CH4 with C2H4. The lack of 13C-labeled benzene revealed that propene is not transformed to benzene, which instead originates entirely from C2H4. The 13C atom is inserted both into the methyl group and benzene ring in the toluene formed. This indicates that toluene is formed by two reaction paths; the reaction of 13CC2H6 with butenes formed by the dimerization of C2H4 and the reaction of benzene with 13CH4. The existence of the latter path was proved by the direct reaction of 13CH4 with benzene. The reaction of methane with benzene was also carried out in a continuous flow system over In-loaded ZSM-5. The reaction afforded 7.6% and 0.9% yields of toluene and xylenes, respectively, at 623 K.     

Revisiting the nature of Cu sites in the activated Cu-SSZ-13 catalyst for SCR reaction

Cu-SSZ-13 is a highly active NH₃-SCR catalyst for the abatement of harmful nitrogen oxides (NO_x, x = 1, 2) from the exhausts of lean-burn engines. The study of Cu-speciation occurring upon thermal dehydration is a key step for the understanding of the enhanced catalytic properties of this material and for identifying the SCR active sites and their redox capability. Herein, we combined FTIR, X-ray absorption (XAS) and emission (XES) spectroscopies with DFT computational analysis to elucidate the nature and location of the most abundant Cu sites in the activated catalyst. Different Cu species have been found to be dominant as a function of the dehydration temperature and conditions. Data analysis revealed that the dehydration process of Cu cations is essentially completed at 250 °C, with the formation of dehydrated [CuOH]⁺ species hosted in close proximity to 1-Al sites in both d6r and 8r units of the SSZ-13 matrix. These species persist at higher temperatures only if a certain amount of O₂ is present in the gas feed, while under inert conditions they undergo virtually total “self-reduction” as a consequence of an OH extra-ligand loss, resulting in bi-coordinated bare Cu⁺ cations. Synchrotron characterization supported by computational analysis allowed an unprecedented quantitative refinement of the local environment and structural parameters of these Cu(ii) and Cu(i) species.     

利用适用于SAPO-34的有机结构导向剂合成SSZ-13分子筛

硅铝分子筛SSZ-13和硅磷铝分子筛SAPO-34已广泛应用于已商业化的催化应用中, 如甲醇制烯烃反应(MTO)和氨气选择性催化还原反应(NH₃-SCR). 目前, 已有多种商业化的有机结构导向剂(OSDA)可用于制备 SAPO-34, 而用于合成SSZ-13的OSDA仍主要依赖经典的N,N,N-三甲基-1-金刚烷基氢氧化铵(TMAdaOH). 因此, 寻找具有较高性价比且可导向合成高硅铝比(SAR)SSZ-13的OSDAs具有重要意义. 本文使用3种可制备SAPO-34的OSDAs[二异丙胺(DIPA)、 二丙胺(DPA)、 正丁胺(nBA)]替代部分TMAdaOH, 发现即使不加入晶种也可合成出SSZ-13. 采用粉末X射线衍射(PXRD)和固体核磁共振(ss-NMR)分析方法对制备的SSZ-13进行了系统研究. 结果显示, 所合成的具有可调变SARs的SSZ-13负载Cu之后, 在NH₃-SCR性能上与商业化催化剂相当. 此外, 通过研究DIPA和TMAdaOH合成SSZ-13的晶化机理发现, DIPA的加入可以加快结晶过程、 提高产率并防止非晶相的形成. 本文提出的观点可为寻找更高效和商业化的SSZ-13结构导向剂及合成具有特定性质的SSZ-13提供参考.     

Catalytic asymmetric epoxidation of alkenes with arabinose-derived uloses

Four l-erythro-2-uloses were readily prepared from l-arabinose via a reaction sequence involving Fischer glycosidation, acetalization and oxidation. Bulky steric sensors at the anomeric center could enhance the stereoselectivity of the dioxirane epoxidation and one of the uloses performed with good enantioselectivity towards trans-stilbene (up to 90% ee). However, the catalysts decomposed during the epoxidation and the maximum chemical yield was only 13% under the basic conditions. Three l-threo-3-uloses could overcome the decomposition problem based on the electron withdrawing effect of the ester group(s) α to the ketone functionality. The best chemical yield was up to 93% using a ketone with two flanking ester groups. One of the improved uloses displayed moderate enantioselectivity towards trans-disubstituted and trisubstituted alkenes (40-68% ee).     

不同硅铝比Al-ITQ-13分子筛的甲醇制丙烯反应催化性能

采用晶种法直接合成了硅铝比(SiO_2/Al_2O_3物质的量比)为137、224和309的三种Al-ITQ-13分子筛,并采用粉末X射线衍射(XRD)、扫描电镜(SEM)、N_2吸附-脱附、固体核磁共振(MAS NMR)和NH_3-程序升温脱附(NH_3-TPD)等分析方法对不同硅铝比分子筛进行了表征,并在固定床微型反应评价装置上,考察了硅铝比对甲醇转化制丙烯反应性能的影响。结果表明,不同硅铝比Al-ITQ-13分子筛呈现出相似的织构性质,酸量及酸强度随着硅铝比的升高逐渐下降。硅铝比对甲醇转化反应的产物分布存在较大的影响;随着硅铝比的升高,氢转移反应和芳构化反应活性降低,使得乙烯选择性下降,而丙烯和丁烯的选择性升高。硅铝比由137提高到309,丙烯的选择性(质量分数)由46.04%增加到55.52%,而丙烯/乙烯比由3.39提高到6.57。     

相转移催化合成2-苯基喹啉衍生物

以喹啉(1)和取代苯肼(2a~2d)为原料,K₂S₂O₈为引发剂,TBAB为相转移催化剂,乙腈为溶剂,经自由基反应合成了4个2-苯基喹啉化合物（3a~3d, 3d为新化合物）,其结构经¹H NMR, ¹³C NMR和HR-ESI-MS表征。以3a的合成为模板反应,研究了引发剂,溶剂和反应温度对3收率的影响。结果表明：在最佳反应条件(1 1.0 mmol, 2 1.2 eq., K₂S₂O₈ 2.0 eq., TBAB 0.2 eq.,于室温反应4 h)下,3a~3d收率54%~72%。     

茶叶中微量硒的催化光度法测定

用催化光度法测定了23个茶叶样品中向量硒的含量,平均回收率97.2%.变异系数2.13%.     

Catalytic amination of unsaturated hydrocarbons: reactions of p-nitrophenylazide with alkenes catalysed by metallo-porphyrins

Porphyrin derivatives of transition metals such as Ru(TPP)CO, Ru(OEP)CO and Co(OEP)(TPP=dianion of 5, 10, 15, 20-tetraphenylporphyrin, OEP=dianion of 2, 3, 7, 8, 12, 13, 17, 18-octaetylporphyrin) catalyse the reaction of p-nitrophenylazide with cyclohexene to give the corresponding allylamine in good yields. With other olefins such as cyclooctene, 1-octene, styrene and substituted styrenes the main product becomes the corresponding aziridine. The reaction of p-nitrophenylazide with Ru(TPP)CO has been investigated and the mechanism of the catalytic reactions is discussed.     

聚苯乙烯负载单茂然／RMgBr催化苯乙烯聚合的研究

合成了聚苯乙希负载的单茂钛催化剂,并与格氏试剂（RMgBr）组成催化体系。考察了聚合温度、催化体系的组成、单体浓度、 Mg/Ti摩尔比、聚合时间等条件对苯乙烯聚合的影响。结果表明,采用负载单茂钛催化剂与助催化剂格氏试剂反应,可以制备出具有较高催化活性的催化剂。DSC表明,不溶于沸丁酮的聚苯乙烯具有一定的定向性。聚合物^13G-NMR测试表明,该催化体系的聚合机理可能是：苯乙烯插入M－C键,以一级插入反应进行链增长,最后以β－H及β－苯基消除反应致链终止。     

Catalytic asymmetric cyclopropanation of allylic alcohols with titanium-TADDOLate: scope of the cyclopropanation reaction.

A substoichiometric amount of titanium-TADDOLate complex was effective at catalyzing the cyclopropanation reaction of allylic alcohols in the presence 1 equiv of bis(iodomethyl)zinc. After initial optimization of the catalyst structure, excellent yields and enantiomeric ratios were obtained for 3-aryl- or 3-heteroaryl-substituted allylic alcohols (up to 97:3). Alkyl-substituted allylic alcohols gave modest yields and enantiomeric ratios (up to 87:13) but these compare favorably with those observed with other substoichiometric chiral ligands. The full synthetic scope of the reaction is presented in this paper.     

Catalytic activation of nitrobenzene on PVP passivated silver cluster: A DFT investigation

Poly(N‐vinyl‐2‐pyrrolidone) (PVP) has been used extensively to stabilize the surface of noble metal nanoparticles against aggregation and also to produce anisotropic nanostructures. Naturally, it is very important to understand the effect of such surface stabilization by PVP on the catalytic activity of these nanoparticles. This communication investigates through DFT calculations the electronic properties of PVP stabilized 13‐atom Ag cluster for catalytic activation of nitrobenzene (NB). These computations suggest that poly(N‐vinyl‐2‐pyrrolidone) (PVP) interact with silver (Ag) cluster mainly through oxygen atom and acts not only as a stabilizer to prevent the aggregation of Ag clusters but also as an electron donor to activate the Ag clusters for further reaction. Natural Bonding Orbital (NBO) calculations show that catalytic activation of NB by PVP passivated Ag cluster occurs due to interaction of the oxygen of the nitro group with the Ag cluster. Weak back donation of electrons from M(dπ) orbital of Ag to antibonding σ* of one of the N O bond, facilitates the formation of the nitroso intermediate. To understand the extent and the nature of this interaction better, vibrational frequency calculation of nitrobenzene association with Ag13‐2PVP cluster is carried out. Red shift in the frequencies is consequence of strong interaction with that of silver cluster present in Ag13‐2PVP‐NB model.     

二苄基锡苯磺酸酯的合成、晶体结构和催化性能

以双三苄基氧化锡([(PhCH2)3Sn]2O)和苯磺酸(PhSO3H)为原料合成了新的二苄基锡苯磺酸酯(PhCH2)2Sn(OS(O)2Ph)2(H2O)2,并采用红外光谱、元素分析和X射线单晶衍射对其结构进行了分析。该化合物的晶体结构属单斜晶系,空间群为P21/c,晶胞参数a=1.458 71(8)nm,b=1.178 21(8)nm,c=0.758 18(4)nm,β=92.393(2)°,V=1.301 92(13)nm-3,Z=2;化合物中所有的锡原子均为略微畸变的八面体构型。当(PhCH2)2Sn(OS(O)2Ph)2(H2O)2催化碳酸二甲酯与苯酚酯交换合成碳酸二苯酯时,碳酸二甲酯的转化率可达55.8%,酯交换选择性接近100%。