Effect of nozzle thickness on the self-excited impinging planar jet

The self-excited oscillation of a large aspect ratio planar jet impinging on a flat plate is investigated experimentally at a single transonic jet velocity to clarify the effect of varying the jet thickness on pattern of jet oscillation and frequency of resulting acoustic tone. The study has been performed for a series of jet thicknesses, 1 mm to 4 mm, each of which is tested for the complete range of plate position, i.e. impingement distance, over which acoustic tones are generated. The results reveal that the jet oscillation is controlled by a fluid-dynamic mechanism for small impingement distances, where the hydrodynamic flow instability controls the jet oscillation without any coupling with local acoustic resonances. At larger impingement distances, a fluid-resonant mechanism becomes dominant, in which one of the various hydrodynamic modes of the jet couples with one of the resonant acoustic modes occurring between the jet nozzle and the impingement plate. Within the fluid-resonant regime, the acoustic tones are found to be controlled by the impingement distance, which is the length scale of the acoustic mode, with the jet thickness having only minor effects on the tone frequency. Flow visualization images of the jet oscillation pattern at a constant impingement distance show that the oscillation occurs at the same hydrodynamic mode of the jet despite a four-fold increase in its thickness. Finally, a feedback model has been developed to predict the frequency of acoustic tones, and has been found to yield reasonable predictions over the tested range of impingement distance and nozzle thickness.     

冲击射流中反馈环机理的再研究

冲击射流的噪声抑制对于研究短程起飞和垂直起降飞行器(STOVL)是极其重要的. 为了研究冲击射流噪声尤其是冲击单音与涡结构尺度之间的关系以及反馈声波的上传方向,采用小波分析技术和``声类比'方法来分析冲击单音的传播方向. 研究中用到的冲击射流的速度场由PIV技术给出,冲击单音的频率通过噪声场的测量获得. 利用双正交小波变换来提取冲击射流速度场中含有的波动信息,结合冲击单音的频率特性对噪声场进行研究.研究结果表明大尺度结构是冲击单音的``拟声源'. 此外,还可以看出大尺度涡结构产生的反馈声波一部分向喷嘴出口处传播,形成反馈环;另一部分反馈声波向四周传播.      

Effects of the surface roughness on heat transfer of perpendicularly impinging co-axial jet

Current work presents the comparison of the cooling characteristics of roughened and smooth heated surfaces subjected to co-axial impinging jet. The work fluid is air and the data runs are performed for jet Reynolds numbers for 10,000, 20,000 and 40,000, and non-dimensional surface to jet exit spacing, H/D, from 1 to 10. The co-axial jet configuration is based on a fully developed pipe flow encountering a double-pipe arrangement and splitting between the two pipes. The inner to outer diameter ratio is 0.5. A straight pipe without inner section is used as the circular jet. The impingement of circular jets to the roughened and smooth surfaces is also performed for comparison. Average Nusslet numbers were obtained to show the heat transfer enhancement from the surface. A good agreement between the literature and present paper was obtained. As a result, average Nusselt number with co-axial jet impingement to the roughened surface increased by up to 27% comparing to the circular jet impingement. In addition, the average Nusselt number increased with roughened surface by up to 6% over the whole surface area, comparing to the smooth surface.     

Wall jet similarity of impinging planar underexpanded jets

Velocity profiles and wall shear stress values in the wall jet region of planar underexpanded impinging jets are parameterized based on nozzle parameters (stand-off height, jet hydraulic diameter, and nozzle pressure ratio). Computational fluid dynamics is used to calculate the velocity fields of impinging jets with height-to-diameter ratios in the range of 15–30 and nozzle pressure ratio in the range of 1.2–3.0. The wall jet has an incomplete self-similar profile with a typical triple-layer structure as in traditional wall jets. The effects of compressibility are found to be insignificant for wall jets with Ma < 0.8. Wall jet analysis yielded power-law relationships with source dependent coefficients describing maximum velocity, friction velocity, and wall distances for maximum and half-maximum velocities. Source dependency is determined using the conjugate gradient method. These power-law relationships can be used for mapping wall shear stress as a function of nozzle parameters.     

Drying performance and surface forces of a pair of impinging radial jets

The drying performance and the forces generated by a pair of radial jets impinging on a plane surface are studied experimentally and compared with a pair of in-line (axial) jets. The reattachment rings of the radial jets are visualized by liquid-crystal-thermography. The results of the drying experiments are presented in terms of Sherwoodnumbers. The results of the surface force measurements are presented in terms of force coefficients. The effects of flow exit angle, exit velocity, horizontal nozzle spacing and vertical nozzle to surface distance on mass transfer and net surface force are discussed. Results show that drying performance of a pair of radial jets with an exit angle towards the surface of 10° is 18% higher than that of a pair of in-line jets. The surface force of impinging radial jets depends on the exit angle. A global pressure force on the surface is typical for jets directed towards the surface, while a global lifting force is found when the jet is initially directed away from the surface. Radial jets have a high potential in drying applications for force sensitive products and when high drying rates and/or small suction forces are of interest.     

Influence of spanwise pitch on local heat transfer distribution for in-line arrays of circular jets with spent air flow in two opposite directions

Effect of spanwise jet-to-jet spacing on local heat transfer distribution due to an in-line rectangular array of confined multiple circular air jets impinging on a surface parallel to the jet plate are studied experimentally. Length-to-diameter ratio of nozzles of the jet plate is 1.0. The flow, after impingement, is constrained to exit in two opposite directions from the confined passage formed between jet plate and target plate. Mean jet Reynolds numbers based on the nozzle exit diameter (d) covered are 3000, 5000, 7500 and 10,000 and jet-to-plate spacings studied are d, 2d and 3d. Spanwise pitches considered are 2d, 4d and 6d in steps of 2d keeping the streamwise pitch at 5d. For all the configurations, the jet-plates have ten spanwise rows in streamwise direction and six jets in each spanwise row. Flat heat transfer surface is made of thin stainless steel metal foil. Local temperature distribution on a target plate is measured using thermal infrared camera. Wall static pressure on the target plate is measured in the streamwise direction to estimate crossflow velocities and individual jet velocities. Heat transfer characteristics are explained on the basis of the flow distribution. A simple correlation to predict streamwise distribution of heat transfer coefficients averaged over each spanwise strip resolved to one jet hole is developed.     

Experimental study of an impinging jet with different swirl rates

A stereo PIV technique using advanced pre- and post-processing algorithms is implemented for the experimental study of the local structure of turbulent swirling impinging jets. The main emphasis of the present work is the analysis of the influence of swirl rate on the flow structure. During measurements, the Reynolds number was 8900, the nozzle-to-plate distance was equal to three nozzle diameters and the swirl rate was varied from 0 to 1.0. For the studied flows, spatial distributions of the mean velocity and statistical moments (including triple moments) of turbulent pulsations were measured.

The influence of the PIV finite spatial resolution on the measured dissipation rate and velocity moments was analyzed and compared with theoretical predictions. For this purpose, a special series of 2D PIV measurements was carried out with vector spacing up to several Kolmogorov lengthscales.

All terms of the axial mean momentum and the turbulent kinetic energy budget equations were obtained for the cross-section located one nozzle diameter from the impinging plate. For the TKE budget, the dissipation term was directly calculated from the instantaneous velocity fields, thereby allowing the pressure diffusion term to be found as a residual one. It was found that the magnitude of pressure diffusion decreased with the growth of the swirl rate. In general, the studied swirling impinging jets had a greater spread rate and a more rapid decay in absolute velocity when compared to the non-swirling jet.     

Numerical simulation of an impinging jet on a flat plate

Two-dimensional normal impinging jet flowfields, with or without an upper plate, were analysed by employing an implicit bidiagonal numerical method developed by Lavante and Thompkins Jr. The Jones–Launder K–? two-equation turbulent model was employed to study the turbulent effects of the impinging jet flowfield. The upper plate surface pressure, the ground plane pressure and other physical parameters of the momentum flowfield were calculated at various jet exit height and jet inlet Reynolds numbers. These results were compared with those of Beam and Warming's numerical method, Hsiao and Chuang, and others, along with experimental data. The potential core length of the impinging jet without an upper plate is longer than that of the free jet because of the effects of the ground plane, while the potential core length of the impinging jet with an upper plate is shorter than that of the free jet because of the effects of the upper plate. This phenomenon in the present analysis provides a fundamental numerical study of an impinging jet and a basis for further analysis of impinging jet flowfields on a variable angle plate.     

Heat transfer augmentation between impinging circular air jet and flat plate using finned surfaces and vortex generators

An experimental investigation is performed to study the effect of the finned surfaces and surfaces with vortex generators on the local heat transfer coefficient between impinging circular air jet and flat plate. Reynolds number is varied between 7000 and 30,000 based on the nozzle exit condition and jet to plate spacing between 0.5 and 6 nozzle diameters. Thermal infrared imaging technique is used for the measurement of local temperature distribution on the flat plate. Fins used are in the form of cubes of 2 mm size spaced at a pitch of 5 mm on the target plate and hexagonal prism of side 2.04 mm and height of 2 mm spaced at a pitch of 7.5 mm. Vortex generators in the form of a equilateral triangle of side 4 mm are used. Effect of number of rows of vortex generators, radius of a row, number of vortex generators in a row and inclination angle (i.e., the angle between the plane of the target plate and the plane of the vortex generators) on Nusselt number is studied. It is observed that the heat transfer coefficient between the impinging jet and the target plate is sensitive to the shape of the fin. The increase in the heat transfer coefficient up to 77% depending on the shape of the fin, nozzle plate spacing and the Reynolds number is observed. The augmentation in the heat transfer for the surfaces vortex generators are higher than that of the finned surfaces. The heat transfer augmentation in case of vortex generator is as high as 110% for a single row of six vortex generators at a radius of 1 nozzle diameter as compared to the smooth surface at a given nozzle plate spacing of 1 nozzle diameter and a Reynolds number of 25,000 at extreme radial location.     

Numerical and experimental study of turbulent impinging twin-jet flow

The two dimensional impinging circular twin-jet flow with no-cross flow is studied numerically and experimentally. The theoretical predications are carried out through numerical procedure based on finite volume method to solve the governing mass, momentum, turbulent kinetic energy and turbulent kinetic energy dissipation rate. The parameters studied were jet Reynolds number (9.5 × 10⁴  Re  22.4 × 10⁴), nozzle to plate spacing (3  h/d  12), nozzle to nozzle centerline spacing (l/d = 3, 5 and 8) and jet angle (0°  θ  20°). It is concluded that the stagnation primary point moves away in the radial main flow direction by increasing the jet angle. This shift becomes stronger by increasing the nozzle to nozzle centerline spacing (l/d). A secondary stagnation point is set up between two jets. The value of pressure at this point decreases by decreasing Reynolds number and/or increasing the jet angle.

The sub atmospheric region occurs on the impingement plate. It increases strongly by increasing Reynolds number and decreases as the jet angle and/or a nozzle to plate spacing increases. The spreading of jet decreases by increasing nozzle to plate spacing. The intensity of re-circulation zone between two jets decreases by increasing of h/d and jet angle. The increase of turbulence kinetic energy occurs within high gradient velocity.     

Optimization of an inclined elliptic impinging jet with cross flow for enhancing heat transfer

This work presents a parametric study and optimization of a single impinging jet with cross flow to enhance heat transfer with two design variables. The fluid flow and heat transfer have been analyzed using three-dimensional compressible Reynolds-averaged Navier–Stokes equations with a uniform heat flux condition being applied to the impingement plate. The aspect ratio of the elliptic jet hole and the angle of inclination of the jet nozzle are chosen as the two design variables, and the area-averaged Nusselt number on a limited target plate is set as the objective function. The effects of the design variables on the heat transfer performance have been evaluated, and the objective function has been found to be more sensitive to the angle of inclination of the jet nozzle than to the aspect ratio of the elliptic jet hole. The optimization has been performed by using the radial basis neural network model. Through the optimization, the area-averaged Nusselt number increased by 7.89% compared to that under the reference geometry.     

A numerical study of turbulent opposed impinging jets issuing from triangular nozzles with different geometries

In present research, two turbulent opposed impinging air jets issuing from triangular nozzles with fixed and variable exit velocity ratios and different nozzle-to-nozzle distances have been studied numerically and then compared with rectangular and circular nozzles. The finite volume method has been applied for solving mass and momentum equations. The turbulence model being used here is k-ε RNG. Distributions of pressure, turbulence, kinetic energy and its dissipation rate in various regions especially on the impingement regions have been obtained with high accuracy. Study of the nozzle geometries has shown the advantage of triangular nozzles over other geometries. First, the triangle’s base in nozzle geometry has an important role in our study case which, mixing two flows and regions with high turbulence intensity, directly depends on it. Second, our results show that circular and rectangular nozzles have less efficiency than triangular nozzles in mixing applications. Third and last, it was found that the radial jet being created by opposed jets has some similarities to free jets. In this investigation, air in standard atmospheric pressure has been applied as working fluid.     

Noise Reduction in Non-Premixed Lifted-Jet Flames

The characteristic changes in non-premixed lifted flames when excited by hole tones from a cavity, placed in the flow path of the fuel gas, were studied. A significant reduction of the sound pressure level was observed in the low-frequency noise at the flame base of the lifted flame when the hole tones were induced in the jet. The liftoff height and the mean diameter of the flame base decreased for a given jet Reynolds number. The blow-off velocities also increased suggesting improved flame stability in the presence of the hole tones induced by the cavity. Incorporation of the cavity upstream of a burner nozzle is demonstrated to give a quieter lifted flame with improved stability characteristics. This revised version was published online in July 2006 with corrections to the Cover Date.     

Self-sustained oscillations of a confined impinging jet

The present paper investigates the dynamics of a laminar plane jet impinging on a flat plate in a channel. An experimental parametric study is carried out to determine the flow regimes at different levels of confinement and Reynolds numbers. For very confined jets, the flow is steady whatever the Reynolds number. The overall structure of the flow is symmetric with respect to the jet axis and is characterized by the presence of recirculation zones at the channel walls. The dynamics is radically different for less confined jets. Above a critical Reynolds number, the flow bifurcates in the form of an oscillating flapping mode of the impinging jet. Analyses of the experimental results provide with a quantitative characterization of this regime in terms of amplitude, wavelength and frequency. This self-oscillating bifurcated flow induces strong sweepings of the target plate by the jet and intense vortex dipole ejections from the impacted wall. Such a regime is expected to be particularly useful in the enhancement of the local heat transfer at relatively low cost in terms of flow rate.     

Numerical analysis of flow pattern of impinging liquid sprays in a cold model for cooling a hot flat plate

This paper treats the numerical analysis of two-phase mist jet flow, which is commonly adopted to cool the solidified shell in the secondary cooling zone of the continuous casting process. Flow structures of the two-phase subsonic jet impinging on a flat plate normal to flow, corresponding to the present cooling situation, are solved on the assumption that particles are perfectly elastically reflected from a surface. Again, the numerical experiments concerning mist flows composed of air and water-droplets are made in a cold model. The flow fields for both gas and particle phases strongly depend upon the particle size. When waterdroplets mixing in the mist are very small, the impinging particles travel very closely to the surface. With increasing particle size, particles are reflected from the surface in a far distance. Therefore, also, the case is analysed where a low velocity annular gas-only flow surrounding a round nozzle co-axially is present so that such idle particles may be pushed back to the surface again. This is considered to result in an improvement of the mist cooling efficiency.     

Computational flow and heat transfer of a row of circular jets impinging on a concave surface

A computational investigation is carried out to study the flow and heat transfer from a row of circular jets impinging on a concave surface. The computational domain simulates the impingement cooling zone of a gas turbine nozzle guide vane. The parameters, which are varied in the study include jet Reynolds number (Re _d = 5000–67800), inter-jet distance to jet diameter ratio (c/d = 3.33 and 4.67) and target plate distance to jet diameter ratio (H/d = 1, 3 and 4). The flow field, predicted with K-ω turbulence model and using Fluent 6.2.16, is characterized with the presence of a pair of counter rotating vortices, an upwash fountain flow and entrainment. The local pressure coefficient and Nusselt number variations along the concave plate are presented and these values are found to under predict the available experimental data by about 12%.     

COMPUTATIONAL STUDIES OF IMPINGING JETS USING K-ϵ TURBULENCE MODELS

This paper reports numerical modelling of impinging jet flows using Rodi and Malin corrections to the k–ϵ turbulence model, carried out using the PHOENICS finite volume code. Axisymmetric calculations were performed on single round free jets and impinging jets and the effects of pressure ratio, height and nozzle exit velocity profile were investigated numerically. It was found that both the Rodi and Malin corrections tend to improve the prediction of the hydrodynamic field of free and impinging jets but still leave significant errors in the predicted wall jet growth. These numerical experiments suggest that conditions before impingement significantly affect radial wall jet development, primarily by changing the wall jet's initial thickness.     

Variational boundary integral approach for asymmetric impinging jets of arbitrary two‐dimensional nozzle

We consider asymmetric impinging jets issuing from an arbitrary nozzle. The flow is assumed to be two‐dimensional, inviscid, incompressible, and irrotational. The impinging jet from an arbitrary nozzle has a couple of separated infinite free boundaries, which makes the problem hard to solve. We formulate this problem using the stream function represented with a specific single layer potential. This potential can be extended to the surrounding region of the jet flow, and this extension can be proved to be a bounded function. Using this fact, the formulation yields the boundary integral equations on the entire nozzle and free boundary. In addition, a boundary perturbation produces an extraordinary boundary integral equation for the boundary variation. Based on these variational boundary integral equations, we can provide an efficient algorithm that can treat with the asymmetric impinging jets having arbitrarily shaped nozzles. Particularly, the proposed algorithm uses the infinite computational domain instead of a truncated one. To show the convergence and accuracy of the numerical solution, we compare our solutions with the exact solutions of free jets. Numerical results on diverse impinging jets with nozzles of various shapes are also presented to demonstrate the applicability and reliability of the algorithm.     

Near field shock structure of dual co-axial jets

Experimental results on the shock structure of dual co-axial jets are presented. The effects of the geometric parameters of the inner nozzle, jet static pressure ratio (ratio of the exit plane static pressures of the inner and outer nozzles) and the ratio of outer to inner nozzle throat area on the shock structure were studied. A superimposed outer and inner jet structure was observed in the schlieren photographs. The inner flow is compressed by the outer flow resulting in the formation of a Mach disc and an exit shock. A parameter incorporating the effect of Mach number of the inner nozzle and jet static pressure ratio was found to correlate the observations regarding the Mach disc location.     

Effect of the Nozzle Edge Shape on the Acoustic Sensitivity of a Jet

The effect of the nozzle edge shape on the acoustic sensitivity of jets, that is, on the dependence of the jet parameters on the amplitude and frequency of the acoustic oscillations produced by an external source, is experimentally studied. The investigation was performed for nozzle edge configurations, the variation of which did not result in a change in the jet characteristics without external acoustic excitation. This means that the change in the edge shape alone had no influence on the flow pattern at the nozzle exit or the boundary layer flow regime on the nozzle walls. Measurements of the dependence of the mean velocity and the velocity fluctuation intensity on the jet axis on the distance from the nozzle exit showed that a change in the nozzle edge shape can lead to a change in the acoustic sensitivity of the jet when the jet is exposed to external acoustic action.