Plasma Treatment of Ni Catalyst for Partial Oxidation of Methane

The 10%Ni/Al2O3 catalyst for partial oxidation of methane was treated by DBD (dielectric barrier discharge) plasma in a continuous system under atmospheric pressure and room temperature by flowing He. It was found that 10%Ni/Al2O3 catalyst treated by plasma presents a higher catalytic activity and an enhanced stability than the catalysts prepared without plasma treatment. The methane conversion over the catalyst treated by plasma is 3%-5% higher than the catalysts untreated by plasma. Moreover,the enhanced dispersion of the catalyst can be achieved by plasma treatment, which can improve the interaction between active species and supports, catalytic activity and the resistance to carbon deposition.     

Direct Oxidation of Methane to Methanol Over Cu-Based Catalyst in an AC Dielectric Barrier Discharge

In this paper, the conversion of methane to methanol on CuO/Al₂O₃ and Mo–CuO/Al₂O₃ catalysts in a plasma reactor was tested. A comparison between catalytic and plasma-catalytic systems had been made in tested temperature range of 50–300°C. Experimental results showed that plasma-catalytic system demonstrated a much better methane conversion than catalytic system in tested temperature range and Mo–CuO/Al₂O₃ revealed a higher catalytic activity than CuO/Al₂O₃ for methanol synthesis. Furthermore, an Arrhenius plot was made in order to deduce the mechanism of plasma activation, which revealed that the presence of plasma decreased the activation energy for both catalysts. In the case of Mo-CuO/Al₂O₃ catalyst, the enhanced activity for methanol synthesis was assumed due to the oxygen vacancies on Mo–CuO/Al₂O₃ catalyst, which can utilize plasma-induced species to improve the catalytic efficiency.     

Plasma catalytic reaction of natural gas to C2 product over Pd-NiO/Al2O3 and Pt-Sn/Al2O3 catalysts

The decomposition of natural gas over Pd-NiO/Al₂O₃ and Pt-Sn/Al₂O₃ is carried out in a microwave catalytic reaction at room temperature. The decomposition of methane is caused by collision by excitation of unstable electronic state. Measuring the flow rate and plasma power can provide kinetic data and indicate the mechanism. The conversion of C₂ products increases from 47 to 63.7% in the microwave plasma catalytic reaction with electric field. Comparing the activities of catalysts, Pd-NiO/Al₂O₃ bimetallic catalyst is more active than Pt-Sn/Al₂O₃ catalyst because of modification of the surface of catalysts by carbon formation. The kinetic modeling of plasma of methane conversion seems related to the power of the electric discharge. It was also revealed that proper coking or polymeric carbon formation improves the catalytic activity; therefore, the conversion of methane may increase over Pd-Ni/Al₂O₃ catalyst in the plasma system.     

柠檬酸添加方式对Mo-Ni-P/Al_2O_3催化剂加氢活性的影响

以Mo、Ni为活性组分,Al_2O_3为载体,采用不同柠檬酸添加方法制备了Mo-Ni-P/Al_2O_3催化剂.通过氢气程序升温还原(H2-TPR)、X射线衍射(XRD),透射扫描电镜(TEM)、XPS等表征方法研究催化剂的物化性质.结果表明:催化剂经柠檬酸的后处理,改善了载体氧化铝表面羟基基团的分布,促使Mo物种以八面体配位多核聚钼酸的形态存在,有效地减弱了载体与活性金属之间的强相互作用,提高了Mo物种的分散度与硫化度,使得催化剂形成更多"Mo-Ni-S"加氢活性相,提高了催化剂的加氢活性.与其他处理方法相比,柠檬酸后处理的催化剂对VGO具有更高的加氢脱硫、脱氮与芳烃饱和性能.     

The Preparation and Characterization of Highly Dispersed PdO over Alumina for Low‐temperature Combustion of Methane

PdO/Al₂O₃ catalysts prepared by glow discharge plasma treatment followed by thermal calcination show a much higher dispersion and a better catalytic activity for methane combustion at relatively low temperatures. The dispersion of palladium active species by such plasma prepared catalysts is 29.7%, 5.4 times higher than that of conventional catalysts. XPS analysis indicates that a surface enrichment of Pd active species (PdO) has been achieved after plasma treatment. The surface atomic composition of PdO of plasma prepared catalysts reaches 10.5%. XRD characterization also confirms a wellcrystallized PdO phase present on the plasma prepared catalyst. The lightoff temperature of the plasma prepared catalyst is 370°C, 50°C lower than that obtained from the conventional catalyst.     

Investigation of macro-/mesoporous Re<Subscript>2</Subscript>O<Subscript>7</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts prepared by a particle-template method for butylene metathesis

Macro-/mesoporous Al₂O₃ supports were prepared by using monodisperse polystyrene (PS) microspheres as a template. The pore volume and BET surface area of the Al₂O₃ supports increased considerably with increasing amounts of the PS microspheres; further investigation showed that PS template only increased the volume of macro-pores but did not change the volume of meso-pores or micro-pores. Macro-/mesoporous Re₂O₇/Al₂O₃ metathesis catalysts were prepared through loading Re₂O₇ onto the as-prepared macro-/mesoporous Al₂O₃ supports, and their catalytic performance was tested in a fixed-bed tubular reactor using the metathesis of normal butylenes as a probe reaction. The results showed that the prepared macro-/mesoporous Re₂O₇/Al₂O₃ catalyst had high activity with consistent selectivity; propylene and pentene accounted for more than 90 wt% of the metathesis products, while the amount of ethylene plus hexane was less than 10 wt%, the majority of which was hexane. These Re₂O₇/Al₂O₃ catalysts had not only higher activity, but also longer working life span and higher tolerance to carbon residues than conventional Re₂O₇/Al₂O₃ catalysts.     

Steam reforming of ethylene glycol over Ni-based catalysts: the effect of K

The effect of K on the activities of Ni/Al₂O₃ catalysts in steam reforming of ethylene glycol was investigated. Ni/Al₂O₃ catalysts were prepared by incipient wetness impregnation and co-precipitation methods. The addition of K was achieved using an incipient wetness impregnation method. The prepared catalysts were characterized by N₂ physisorption, inductively coupled plasma-atomic emission spectroscopy, X-ray diffraction, temperature-programmed reduction, and scanning electron microscopy. Irrespective of the preparation method, the promotional effect of K was observed and the optimum K content (~5 wt%) was verified for K-promoted Ni/Al₂O₃ catalysts. The addition of K to the Ni–Al₂O₃ catalyst prepared by co-precipitation led to higher catalytic activity than addition of K to the Ni/Al₂O₃ catalyst prepared by incipient wetness impregnation.     

Gold catalysts supported on ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for low-temperature CO oxidation

Gold catalysts with loadings ranging from 0.5 to 7.0 wt% on a ZnO/Al₂O₃ support were prepared by the deposition–precipitation method (Au/ZnO/Al₂O₃) with ammonium bicarbonate as the precipitation agent and were evaluated for performance in CO oxidation. These catalysts were characterized by inductively coupled plasma-atom emission spectrometry, temperature programmed reduction, and scanning transmission electron microscopy. The catalytic activity for CO oxidation was measured using a flow reactor under atmospheric pressure. Catalytic activity was found to be strongly dependent on the reduction property of oxygen adsorbed on the gold surface, which related to gold particle size. Higher catalytic activity was found when the gold particles had an average diameter of 3–5 nm; in this range, gold catalysts were more active than the Pt/ZnO/Al₂O₃ catalyst in CO oxidation. Au/ZnO/Al₂O₃ catalyst with small amount of ZnO is more active than Au/Al₂O₃ catalyst due to higher dispersion of gold particles.     

Catalytic Combustion of Ethyl Acetate over Al2O3- Ce0.5Zr0.5O2 Supported Metal Oxide Catalysts

The catalysts for the combustion of ethyl acetate were prepared using Fe, Co, Cu, Cr, and Mn metal oxide as active components supported on Al₂O₃-Ce_0.5Zr_0.5O₂ mixed oxides and characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), oxygen storage capacity measurement, BET surface area, XPS measurement, and activity test. According to the results of characterization, it was found that Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) catalysts presented excellent activity for the catalytic combustion of ethyl acetate, because of the more reducible species and high reducibility of the catalysts. For ethyl acetate oxidation, more than 99% conversion was achieved at 245 °C over catalysts Cu/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2) and Mn/Al₂O₃-Ce_0.5Zr_0.5O₂ (1:2, mass ratio), indicating that the catalysts had great potential for wide use.     

P改性对Mo-Ni/Al2O3煤焦油加氢脱氮性能的影响

在磷含量1.34%下,采用分步浸渍法按磷添加顺序不同制备了3种改性催化剂:MoP-Ni/Al₂O₃、Mo-NiP/Al₂O₃、Mo-Ni/PAl₂O₃.通过X射线衍射(XRD)、程序升温脱附(NH₃-TPD)、程序升温还原(H₂-TPR)、氮气吸附等技术对催化剂进行了表征.以新疆中低温煤焦油为原料,考察了不同磷改性方式对催化剂加氢脱氮(HDN)性能的影响.结果表明,适宜的磷添加方式能够改变催化剂的酸性分布,提高10~13 nm加氢脱氮有效孔的比例,并且减弱活性组分与载体的相互作用,同时使得活性组分更易被还原,进而提高催化剂加氢脱氮性能.加氢脱氮活性顺序为Mo-Ni/PAl₂O₃(74.36%)>Mo-NiP/Al₂O₃(72.74%)>Mo-Ni/Al₂O₃(71.72%)>MoP-Ni/Al₂O₃(56.13%).     

SiO2和Al2O3负载的Ni基催化剂在甲烷干重整中的催化性能差异

CH₄与CO₂干重整反应对于环境保护和天然气资源的合理利用具有重要意义。SiO₂和Al₂O₃是适用于甲烷干重整反应的两种典型的催化剂载体。为了阐明这两种载体对催化剂性能的影响,本研究采用等体积浸渍法制备了Ni/Al₂O₃和Ni/SiO₂催化剂,并利用BET、TEM、H₂-TPR、XRD、TG和Raman等技术对还原和反应后的催化剂进行了表征。结果表明,由于载体的性质不同,Ni基催化剂在甲烷干重整中的催化性能也不同。Ni/SiO₂催化剂的初始活性较高,但由于其金属-载体相互作用较弱,催化稳定性较差,在800℃下反应15h其催化活性急剧下降;较弱的金属-载体相互作用使得Ni/SiO₂催化剂上的Ni颗粒较大,有利于积炭前驱物种的生成,导致催化剂快速失活。而对于Ni/Al₂O₃催化剂,金属-载体相互作用较强,Ni颗粒较小,但由于Ni与Al₂O₃生成了NiAl_xO_y物种,有效活性位减少,其催化活性相对较低,但催化稳定性较好,干重整反应进行50h其活性保持稳定;Ni与Al₂O₃之间较强的相互作用有利于形成小且稳定的Ni粒子,能减少积炭,因而具有优异的催化稳定性。     

乙烷氧化脱氢用Ni/Al2O3催化剂中活性镍物种前驱体（英文）

Ni/Al2O3 catalysts for oxidative dehydrogenation(ODH) of ethane were prepared by impregnation of Al2O3 with nickel acetate or nickel nitrate,and by mechanical mixing of NiO and Al2O3.The Ni-based catalysts were characterized by N2 adsorption-desorption,X-ray diffraction,diffuse reflectance UV-visible diffuse reflectance spectroscopy,and temperature-programmed reduction of hydrogen.The results showed that formation of crystalline NiO particles with a size of < 8 nm and/or non-stoichiometric NiO species in the Ni/Al2O3 catalysts led to more active species in ODH of ethane under the investigated reaction conditions.In contrast,tetrahedral Ni species present in the catalysts led to higher selectivity for ethene.Formation of large crystalline NiO particles(22-32 nm) over Ni/Al2O3 catalysts decreased the selectivity for ethene.     

Catalytic activities of Mo-modified Ni/Al2O3 catalysts for thioetherification of mercaptans and di-olefins in fluid catalytic cracking naphtha

A series of molybdenum-modified Ni/Al₂O₃ catalysts were prepared, and their catalytic activities and stabilities for thioetherification of mercaptans and di-olefins in fluid catalytic cracking (FCC) naphtha were investigated. The sulfided catalyst samples were characterized by a range of physical techniques. The results showed that the addition of Mo to Ni catalysts could improve the degree of dispersion of Ni species in the carrier, inhibit the formation of NiAl₂O₄ crystallites, enhance the presulfidation degree of the metals, and change the chemical environment and electronic structure of Ni. These effects could significantly improve the activity of the Ni/Al₂O₃ catalysts for thioetherification in FCC naphtha. Furthermore, addition of a small amount of Mo improved the di-olefin selective hydrogenation ability of the Ni/Al₂O₃ catalyst and significantly reduced coke formation during the reaction.     

贵金属铱对氨分解用镍基催化剂的促进作用研究

用湿式浸渍法制备了不同贵金属质量分数的镍-铱双金属催化剂,以氨分解为模型反应对其催化性能进行考察.结果表明,贵金属铱的添加提高了10%Ni/γ-Al2O3的低温活性.在铱的质量分数不高于1%时,氨分解反应活性随铱质量分数的增加出现最大值(相应的Ir质量分数为0.7%),对应的10%Ni-0.7%Ir/γ-Al2O3催化剂在400 ℃时,氨分解率为43.55%,较单组分的Ni催化剂高40.0%.用H2-TPR、H2-TPD 、BET和XRD表征方法对催化剂进行了表征.结果表明,Ir与活性组分Ni之间存在协同作用.铱的添加促进了活性组分的分散、减小了镍的晶粒尺寸,且增加了催化剂活性位的数量,从而提高了催化剂的氨分解性能.     

M/Al2O3-CeO2（M=Pt-Ru，Ru，Pt）催化剂在甲胺催化湿式氧化中的活性与选择性

采用浸渍法制备了M/Al₂O₃-CeO₂（M=Pt-Ru,Ru,Pt）催化剂,并将其用于甲胺的催化湿式氧化反应（CWAO）.结果表明,Pt-Ru/Al₂O₃-CeO₂具有最佳活性和选择性.运用程序升温还原、X射线光电子能谱、X射线衍射、透射电子显微镜、N₂吸附和CO化学吸附等技术对催化剂的物化性质进行了表征.Pt组分的引入可有效提高双金属催化剂活性组分的分散度,从而明显提高了其催化性能.升降温过程中总有机碳（TOC）转化率与N₂选择性迟滞效应表明,甲胺CWAO遵循化学吸附-脱附机理.     

Synthesis of Supported Bimetal Catalysts using Galvanic Deposition Method

Supported bimetallic catalysts have been studied because of their enhanced catalytic properties due to metal‐metal interactions compared with monometallic catalysts. We focused on galvanic deposition (GD) as a bimetallization method, which achieves well‐defined metal‐metal interfaces by exchanging heterogeneous metals with different ionisation tendencies. We have developed Ni@Ag/SiO₂ catalysts for CO oxidation, Co@Ru/Al₂O₃ catalysts for automotive three‐way reactions and Pd−Co/Al₂O₃ catalysts for methane combustion by using the GD method. In all cases, the catalysts prepared by the GD method showed higher catalytic activity than the corresponding monometallic and bimetallic catalysts prepared by the conventional co‐impregnation method. The GD method provides contact between noble and base metals to improve the electronic state, surface structure and reducibility of noble metals.     

Hydrogen Production by Steam Reforming of Ethanol Over Mesoporous Ni–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–ZrO<Subscript>2</Subscript> Catalysts

This review paper reports the recent progress concerning the application of nickel–alumina–zirconia based catalysts to the ethanol steam reforming for hydrogen production. Several series of mesoporous nickel–alumina–zirconia based catalysts were prepared by an epoxide-initiated sol–gel method. The first series comprised Ni–Al₂O₃–ZrO₂ xerogel catalysts with diverse Zr/Al molar ratios. Chemical species maintained a well-dispersed state, while catalyst acidity decreased with increasing Zr/Al molar ratio. An optimal amount of Zr (Zr/Al molar ratio of 0.2) was required to achieve the highest hydrogen yield. In the second series, Ni–Al₂O₃–ZrO₂ xerogel catalysts with different Ni content were examined. Reducibility and nickel surface area of the catalysts could be modulated by changing nickel content. Ni–Al₂O₃–ZrO₂ catalyst with 15 wt% of nickel content showed the highest nickel surface area and the best catalytic performance. In the catalysts where copper was introduced as an additive (Cu–Ni–Al₂O₃–ZrO₂), it was found that nickel dispersion, nickel surface area, and ethanol adsorption capacity were enhanced at an appropriate amount of copper introduction, leading to a promising catalytic activity. Ni–Sr–Al₂O₃–ZrO₂ catalysts prepared by changing drying method were tested as well. Textural properties of Ni–Sr–Al₂O₃–ZrO₂ aerogel catalyst produced from supercritical drying were enhanced when compared to those of xerogel catalyst produced from conventional drying. Nickel dispersion and nickel surface area were higher on Ni–Sr–Al₂O₃–ZrO₂ aerogel catalyst, which led to higher hydrogen yield and catalyst stability over Ni–Sr–Al₂O₃–ZrO₂ aerogel catalyst.     

Co-Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni-W/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Potential and prospects for use in hydrotreating of light cycle oil from catalytic cracking

Со-Мо/Al₂O₃ and Ni-W/Al₂O₃ catalysts were tested in hydrotreating of light cycle oil from catalytic cracking, of the straight-run gasoil, and of their mixture under typical hydrotreating conditions used in industry. The catalysts prepared using PMo₁₂ and PW₁₂ heteropoly acids exhibit high catalytic activity. The Со-Мо/Al₂O₃ catalyst is more active in hydrodesulfurization and hydrogenation of olefin and diene hydrocarbons, whereas the Ni-W/Al₂O₃ catalysts are more active in hydrogenation of mono- and polycyclic aromatic hydrocarbons. Comparison of the quality characteristics of the hydrogenizates obtained with the requirements of the technical regulations shows that the required levels of the sulfur content and cetane number of the hydrogenizates at practically accessible process parameters can be reached for mixtures of the straight-run gasoil and light cycle oil from catalytic cracking with high content of the latter component only when the process with the Со-Мо/Al₂O₃ system and Ni-W/Al₂O₃ catalysts is performed in two steps.     

Ni/Al2O3 catalysts for CO methanation: Effect of Al2O3 supports calcined at different temperatures

The correlation between phase structures and surface acidity of Al₂O₃ supports calcined at different temperatures and the catalytic performance of Ni/Al₂O₃ catalysts in the production of synthetic natural gas (SNG) via CO methanation was systematically investigated. A series of 10 wt% NiO/Al₂O₃ catalysts were prepared by the conventional impregnation method, and the phase structures and surface acidity of Al₂O₃ supports were adjusted by calcining the commercial γ-Al₂O₃ at different temperatures (600–1200 °C). CO methanation reaction was carried out in the temperature range of 300–600 °C at different weight hourly space velocities (WHSV = 30000 and 120000 mL·g^?1·h^?1) and pressures (0.1 and 3.0 MPa). It was found that high calcination temperature not only led to the growth in Ni particle size, but also weakened the interaction between Ni nanoparticles and Al₂O₃ supports due to the rapid decrease of the specific surface area and acidity of Al₂O₃ supports. Interestingly, Ni catalysts supported on Al₂O₃ calcined at 1200 °C (Ni/Al₂O₃-1200) exhibited the best catalytic activity for CO methanation under different reaction conditions. Lifetime reaction tests also indicated that Ni/Al₂O₃-1200 was the most active and stable catalyst compared with the other three catalysts, whose supports were calcined at lower temperatures (600, 800 and 1000 °C). These findings would therefore be helpful to develop Ni/Al₂O₃ methanation catalyst for SNG production.     

The preparation of fluoroarenes by the catalytic decarboxylation of aryl fluoroformates

The catalytic decarboxylation of phenyl fluoroformate to fluorobenzene has been achieved with yields of 70–80% in a flow system using alumina or alumina-based catalysts. The reaction occurs in short space times (<1 s) and with optimal efficiency at ca. 300 °C (some 500 °C lower than the temperature required for the thermal decomposition of the fluoroformate). Impregnation of the alumina with a platinum group metal gave the following order of catalytic activity; Pt/Al₂O₃>Pd/Al₂O₃>Rh/Al₂O₃≈Al₂O ₃.2,4,6-Trimethlyphenyl flouroformate, a new material, was found to decarboxylate similarly to give 1-flouro-2,4,6-trimethylbenzene, but 4-chlorophenyl flouroformate was noted to produce only low yields (～10%) of the corresponding arly flouride