正己烷在Pt/Al_2O_3催化剂上的完全氧化

用外循环无梯度反应器研究了在Pt/Al_2O_3催化剂上内扩散对己烷完全氧化动力学的影响。当催化剂为30—40目时己烷完全氧化在动力学区域进行,当催化剂颗粒增大到4mm时反应在内扩散区域进行,催化剂有效因子在O.14—O.38之间。它表明反应严重地受内扩散阻碍。在氧分压过量时,在动力学区域已烷完全氧化的反应级数为0级,在内扩散区域它变为O.45级。动力学区域的表观活化能为19.OkJ/mol,内扩散区域的表观活化能为10.7kJ/mol,它近似动力学区域活化能及扩散活化能的算术平均值。用试射法及Euler方法计算了已烷在催化剂孔内的分压分布。     

在Pt/Al2O3催化剂上苯的内扩散对负0.9级动力学的影响

在Pt/Al₂O₃催化剂上用外循环反应器研究了内扩散对苯完全氧化动力学的影响,当用30～40目(即0.45～0.60mm)催化剂时反应在动力学区域进行.若O₂过量时则动力学区域苯的完全氧化可用-0.9级速率方程描述.当催化剂粒径增至φ6×5mm时,反应在内扩散区域进行并变为一0.1级反应.催化剂有效因子η在0.24～0.12之间.在同一温度下,η_实验随苯分压p_苯的增加而增大;而p_苯相近时,η_实验则随温度的升高而减小.动力学区域的反应活化能为55.5kJ/mol,内扩散区域的反应活化能为34.9kJ/mol,其值约为动力学区域的活化能与苯分子扩散活化能的算术平均值.     

裂解汽油中噻吩硫在Co-Mo/Al2O3上的催化加氢宏观动力学

采用绝热管式固定床积分反应器，在2.5MPa~3.9MPa、513K~655K、氢/裂解汽油摩尔比1.8~3.5和裂解汽油中噻吩、单甲基噻吩和双甲基噻吩质量分数为838×10－6、137×10－6~723×10－6和192×10－6~723×10－6下，对Co-Mo/Al2O3催化剂上裂解汽油催化加氢脱硫的宏观动力学进行了研究。以Powell优化法和Merson迭代法对动力学实验数据进行非线性参数估值，建立了良好吻合实验数据的、裂解汽油催化加氢脱硫的幂函数型宏观动力学模型。噻吩、单甲基噻吩和双甲基噻吩的反应级数分别为0.721、0.735和0.87，对应的加氢反应宏观活化能依次为70.0kJ·mol－1、67.9kJ·mol－1和59.9kJ·mol－1。各噻吩基硫的转化率均随反应压力的提高而增加，3.5MPa以上时，增加的趋势减缓；反应温度的提高有利于噻吩基硫转化率的增加；593K以上时，各硫化物的转化率随温度的增加呈现线性增加的趋势。     

分子筛USY负载硼化钴非晶态合金催化剂的制备及其在催化硼氢化钠水解制氢中的应用

采用浸渍法与化学还原法相结合制备了一系列USY型分子筛负载非晶态合金硼化钴(CoB/USY)催化剂,并系统探究了该催化剂在催化硼氢化钠水解制氢中的催化活性。 XRD表征表明,USY分子筛载体上负载的活性组分CoB属于非晶态结构。 通过扫描电子显微镜,对比了负载型CoB/USY催化剂和粉末状CoB催化剂的微观形貌,发现非晶态合金活性组分CoB能够很好的分布在USY分子筛载体表面,较粉末状CoB有更高的分散度。 催化硼氢化钠水解制氢实验结果表明,相对于粉末状CoB催化剂,负载型CoB/USY催化剂在硼氢化钠水解制氢中具有更高的催化活性,30 ℃时NaBH₄水解产氢速率约为1.5 L/(min·g)。 反应动力学的计算结果显示,负载型CoB/USY催化剂在催化NaBH₄水解制氢反应中表观活化能约为65.9 kJ/mol,大大低于粉末状CoB催化剂的活化能(72.1 kJ/mol)。     

Ni-Mg复合催化剂催化裂解CH_4制氢动力学研究

基于定温热重实验,建立了甲烷催化裂解反应动力学模型和催化剂表面积炭失活动力学模型。其中,甲烷催化裂解动力学模型将初始产氢速率视为催化剂未积炭条件下的动力学基础数据;催化剂表面积炭失活动力学则基于甲烷催化裂解速率的降低。实验使用Ni-Mg复合催化剂,分别在535、585、635℃,甲烷分压10~4、2×10~4、3×10~4Pa条件下展开甲烷催化裂解动力学特性研究。结果表明,甲烷催化裂解的反应级数为0.5,活化能为82 k J/mol;Ni-Mg复合催化剂反应失活级数为0.5,催化剂失活活化能为118 k J/mol。实验条件下均制得了多壁碳纳米管。     

Catalytic gasification of Pakistani Lakhra and Thar lignite chars in steam gasification

采用热重法在常压与700℃~900℃条件下的水蒸气气化过程,对两种巴基斯坦Lakhra和Thar褐煤半焦进行了单一和混合催化剂(即3%钙和5%钠-黑液单一催化剂及一种3%钙和5%钠-黑液混合催化剂)对碳转化率、气化反应速率常数及活化能、有害污染含硫气体相对量的催化效应研究.两者Lakhra和Thar褐煤半焦经直接气化就可获得高的碳转化率,但采用纸浆黑液催化剂可使气化速率变得很快.含灰高的Thar褐煤半焦在纸浆黑液催化气化过程更易生成一些复杂的硅酸盐,从而导致比含灰低的Lakhra褐煤半焦出现一个更低的转化率.在水蒸气气化过程由半焦和纸浆黑液自身所产生的SO2 和 H2S含硫气体可为存在于纸浆黑液中的Ca盐所捕获而完成脱硫过程,但这一过程在低于900℃时更有效.缩芯模型 (SCM)可较好地用来关联转化率与时间的关系并给出不同温度下的反应速率常数k.基于阿累尼乌斯方程预测了反应活化能Ea 和指前因子A.在纸浆黑液和钙混合催化及纸浆黑液催化剂时,Lakhra褐煤半焦的Ea分别为44.7kJ/mol和 59.6kJ/mol明显小于Thar褐煤半焦的Ea=114.6kJ/mol 和 Ea=100.8kJ/mol,同样也小于无催化剂纯半焦气化时Lakhra褐煤半焦的Ea=161.2kJ/mol和Thar半焦的Ea=124.8kJ/mol.     

Kinetic studies on vapor phase carbonylation of methanol to acetic acid over Rh/Ys catalyst

A novel catalyst Rh/Ys for the carbonylation of methanol to acetic acid with CH3I as the promoter shows excellent activity and selectivity.The reaction is kinetically controlled.The reaction rate is in proportion to the concentration of Rh and CH3I but has nothing to do with those of CH3OHH and CO.The surface active energy is Ea ~51.02 kJ/mol.A mechanism is also proposed.     

水蒸气气氛煤中温催化气化动力学研究

以碳酸钾为催化剂,用热天平的等温热重法研究了四种不同变质程度煤焦常压下水蒸气催化气化反应动力学。在加和不加碳酸钾条件下,测定了温度为700~850℃煤焦的化学反应控制条件下的碳转化率与时间的关系。碳酸钾催化剂的加入对变质程度越高煤的气化催化作用越大。加碳酸钾的碳转化率与时间的关系用混合模型和修正随机孔模型可以良好的拟合关联,均相模型关联较差。利用修正随机孔模型拟合关联出了四种煤焦催化水蒸气气化反应的活化能和指前因子,活化能为90.317~167.861kJ/mol,指前因子和活化能之间具有补偿效应。     

铜基催化剂上甲烷催化燃烧反应动力学特性研究

采用固定床微分反应器,在常压、450~500℃、甲烷体积分数10%~35%条件下,进行铜基催化剂上甲烷催化燃烧动力学特性研究。研究表明,甲烷分压对反应速率影响显著,而氧气分压的影响可以忽略。采用最小二乘法进行动力学模型参数估计,建立的反应动力学模型为-rCH4=1.61×107×e-108 000/RT×pCH40.5。检验结果表明,所建模型与实验数据良好相容,是适宜和可信的。根据实验结果推断甲烷催化燃烧分两步进行,首先氧气快速与铜基催化剂上活性空位点反应,形成吸附氧气分子;随后吸附氧气分子和甲烷分子反应,生成二氧化碳和水。     

Temperature dependence of the kinetics for the complete oxidation of methane on palladium and palladium oxide

The kinetics for the complete combustion of methane was studied on a Pd foil in the regions where the oxide and then the metal were the bulk stable phases. The use of a model catalyst allowed the kinetics to be studied at higher temperatures than are possible on supported catalysts since heat and mass transport limitations could be avoided for this nonporous model catalyst. For all reaction conditions, CH4 and O2 reaction orders remained the same at about 0.7 and 0, respectively. With PdO as the stable phase, the water reaction order increased from -1 to 0 and the apparent activation energy (Ea) decreased from 125 to 30 kJ mol(-1) as the reaction temperature increased from 600 to 880 K. We propose that as the temperature is increased water desorbs from the sites responsible for combustion and as a result water inhibition and Ea decrease. To investigate the rate of reaction on Pd versus PdO, the rates were measured around the Pd-PdO transition temperature. The turnover rate decreased from 3.0 s(-1) to 0.3 s(-1) at the transition temperature (907 K with 1.5 Torr O2 and 0.30 Torr CH4) when PdO decomposed to Pd metal, showing that PdO was more active than Pd metal for methane oxidation at this temperature. The reaction orders for Pd metal in the range of 933-1003 K were 0.7, 0, and 0 for methane, water, and O2, respectively, with an apparent activation energy of 125 kJ mol(-1). Thus, the turnover rate and Ea changes suggest that the reaction mechanism for methane oxidation on Pd is different from the one on PdO.     

馏分油浆态床加氢处理研究: II FCC柴油加氢工艺条件及动力学研究

对FCC柴油在浆态床柴油加氢催化剂SP25上的加氢工艺条件进行了优化,并考察了加氢脱硫（HDS）和加氢脱氮（HDN）动力学。结果表明,提高反应温度、提高反应压力、增加催化剂的加入量、延长反应时间都能提高催化剂的加氢精制活性,最佳的FCC柴油浆态床加氢工艺条件为,温度350℃、压力6MPa、催化剂加入量6%、反应时间2h。催化剂循环使用性能的考察结果表明,SP25催化剂具有良好的活性稳定性。动力学研究结果表明,FCC柴油的加氢脱硫反应过程可以分为两个阶段。第一阶段为较易脱除的苯并噻吩类（BTs）硫化物的加氢脱硫反应,反应活化能为70.00kJ/mol;第二阶段为较难脱除的二苯并噻吩类（DBTs）硫化物的加氢脱硫反应,反应活化能为85.65kJ/mol。FCC柴油HDN反应的活化能为79.91kJ/mol。烷基取代的二苯并噻吩类硫化物（特别是DMDBTs）是加氢精制反应中最难脱除的含杂原子（S或N）烃类化合物。     

HTPB／TDI,HDI聚合反应动力学研究

对端羟基聚丁二烯／甲苯二异氰酸酯，端羟基聚丁二烯／己二异氰酸酯甲苯溶液体系进行了反应动力学研究，用基团分析方法计算了相应体系的活化能，并对无催化剂和有催化剂的体系作了比较。结果表明，二丁基二月桂酸象对上述体系有强的催化作用，使体系的活化能降低，反应速度加快。对于对端差基聚丁二烯／甲苯二异氰酸酯体系，无催化剂时前后期反应活化能分别为２９．１ｋＪ／ｍｏｌ、３７．４ｋＪ／ｍｏｌ，有催化剂时前后期反应活化     

多孔聚苯醚的合成及气体储存

通过厄尔曼缩合反应合成了一种具有dia-c5 拓扑结构的多孔聚苯醚JUC-Z6, 并对其结构进行了表征. 结果表明, 该化合物具有高热稳定性(214℃ 失重5%), 高化学稳定性、 高BET比表面积(192 m²/g)及窄孔径分布(1.36 nm). 低压气体吸附测试结果表明, JUC-Z6在多孔材料中具有较高的吸附焓(氢气4.1 kJ/mol, 二氧化碳33.7 kJ/mol, 甲烷4.1 kJ/mol).     

KINETICS OF THE CARBONYLATION OF METHANOL IN A MECHANICALLY AGITATED REACTOR

lntroductionThclox"-tcmpcraturcs)nthcsisofmcthanolfroms}'nthcsisgasviamcth}'lformatcconsistsofcarbon}'IationofMc0Htomcth}'lformatc(McF)(bclox`l()O"C).andhydr0gcnol\'sisofMcF(bclot"2OO"C)totx"oMcOHasshox`nbclo`"fCH30H C0=HC0OCH;l(l)HC00CH3 2H2=2CH3OH(2)Wcrcfcrtothisasthctx"o-stcpmcthanoIs}nthesis.Thccarbonylationofmcthanolisahomogcncousl}'catal}'zcdrcactionusingalkalimctalmethoxidesascataIystsinthellquidphasc.Thct},picalrcactionconditionsarc60~90"Cand3.O~5.OMPa.Thercactionisanex…     

Aromatization of Heptene-2 on Pt/Al2O3 Catalysts

Heptene-2 aromatization on Pt/Al₂O₃ in a pulse microcatalytic reactor has been studied under H₂ and N₂ atmosphere at temperatures between 330 to 500°C and at a total pressure of 4.0 kg/cm². Results showed that the production of only cracked products (mainly methane) from deep fragmentation of heptene-2 in H₂ sharply contrasts with the reaction in N₂ in which the catalyst showed aromatic selectivity with the production of methane, benzene and toluene. In H₂-N₂ mixtures, 75% H₂ was required to reduce the aromatization activity of the catalyst to zero. A test of the kinetic data using Sica's method [15] of pulse kinetic analysis suggests a first order in heptene-2 with an activation energy of 102.61 kJ/mol in N₂ and 124.71 kJ/mol in H₂. The difference in activation energies has been attributed to a difference in reaction mechanisms in both gases.     

Preparation of hydrogenated nitrile rubber using palladium acetate catalyst: Its characterization and kinetics

Hydrogenated nitrile rubber was prepared by using palladium acetate as the homogeneous catalyst system. The effect of different reaction parameters on the level of hydrogenation was studied. The extent of hydrogenation increased with increase in reaction time, temperature, pressure, and catalyst concentration. A maximum conversion of 96% could be achieved. The degree of hydrogenation was estimated from IR and NMR spectroscopy. The selectivity of the catalyst in reducing ? C?C? in presence of ? C?N was supported by IR and ¹³C-NMR spectra. ESCA studies further confirmed this observation. Properties of hydrogenated nitrile rubber were investigated by various techniques such as gel permeation chromatography (GPC), glass transition temperature (T_g), stress-strain behavior and rheological measurements. GPC studies showed no significant change in molecular weights of the products after the reaction. T_g value decreased with an increase in the level of hydrogenation. The ultimate stress improved significantly with the increase in the extent of hydrogenation. The die swell decreased with hydrogenation at a particular shear rate. The kinetics of the NBR hydrogenation were investigated. With the increase of the hydrogen pressure and catalyst concentration, the rate of the reaction increased. The reaction was apparently first order with respect to olefinic substrate at higher hydrogen pressure. The apparent activation energy, enthalpy, and entropy of the reaction were calculated as 29.9 kJ/mol, 27.42 kJ/mol, and –0.20 kJ mol^?1 K^?1, respectively.     

Activation energy of methyl radical decay in methane hydrate

The thermal stability of gamma-ray-induced methyl radicals in methane hydrate was studied using the ESR method at atmospheric pressure and 210-260 K. The methyl radical decay proceeded with the second-order reaction, and ethane molecules were generated from the dimerization process. The methyl radical decay proceeds by two different temperature-dependent processes, that is, the respective activation energies of these processes are 20.0 +/- 1.6 kJ/mol for the lower temperature region of 210-230 K and 54.8 +/- 5.7 kJ/mol for the higher temperature region of 235-260 K. The former agrees well with the enthalpy change of methane hydrate dissociation into ice and gaseous methane, while the latter agrees well with the enthalpy change into liquid water and gaseous methane. The present findings reveal that methane hydrates dissociate into liquid (supercooled) water and gaseous methane in the temperature range of 235-260 K.     

Oxide talum-containing catalysts of ozone decomposition and methane oxidation

The oxidation of manganese ions is shown to occur in ozone decomposition on manganese-containing catalyst, leading to the deactivation of a sample. The structure of the iron-containing catalyst does not change, ensuring its high stability during ozone decomposition in a dry gas flow at room temperature, conducted in the region of inner diffusion with an activation energy of 15.5 ± 0.7 kJ/mol. The presence of manganese cations in the intermediate stages of reduction is found to increase their activity in the reaction of deep methane oxidation.     

非晶态超微粒子镍合金催化剂的研究──Ⅱ．Ni－B催化剂对苯加氢反应动力学的研究

非晶态超微粒子镍合金催化剂的研究──Ⅱ．Ｎｉ－Ｂ催化剂对苯加氢反应动力学的研究李同信，张秀峰，李合秋（中国科学院大连化学物理研究所，大连１１６０２３）靳常德，蒋育林，崔建彤，王大庆（大连理工大学化工学院，大连１１６０１１）关键词非晶态超微粒子，镍基合...