Zein films with ZnO and ZnO:Mg quantum dots as functional nanofillers: New nanocomposites for food package with UV-blocker and antimicrobial properties

The preparation of a new nanocomposite by combining zein and quantum dots (QDs) was the main interest of the present work. By the sol-gel method, colloidal ethanolic dispersions of zinc oxide (ZnO) particles and ZnO particles doped with magnesium (II) (ZnO:Mg) were obtained, sized 4.26 and 3.65 nm, respectively, as determined by UV–Vis spectroscopy. The prepared QDs were used as nanofillers in order to obtain zein-based nanocomposite films, which displayed good visual appearance, homogeneity, and transparency. The presence of QDs increased the hydrophobicity and reduced, up to three times, the amount of water uptake of the composite films when compared to pure zein. Those effects were more pronounced for ZnO:Mg QDs. TEM, FTIR, and fluorescence microscopy analysis indicated that zein interacts more effectively with ZnO:Mg than with ZnO. In addition, and most importantly, the presence of QDs in the films showed an important advantage when compared to those of pure zein: the extended UV-blocking in the absorbance spectra. The antimicrobial assays demonstrated that the ZnO NPs, loaded into zein films, are promising antibacterial materials since the inhibition of growth of S. aureus reached (96.5 ± 4.9)% at 44.8 wt% of ZnO NPs. Therefore, the nanocomposites show promising features for the development of food packaging, UV protective films, and for the development of new and sustainable materials.     

Transparent polymeric hybrid film of ZnO nanoparticle quantum dots and PMMA with high luminescence and tunable emission color

ZnO nanoparticle quantum dots (QDs)/poly(methyl methacrylate) (PMMA) composites are synthesized by conventional radical polymerization in the presence of 3-(trimethoxysilyl)propylmethacrylate (TPM)-modified ZnO nanoparticle QDs. Although unmodified ZnO nanoparticle QDs were precipitated in tetrahydrofuran (THF) and show only weak emissions under UV irradiation, ZnO nanoparticle QDs/PMMA composite is well dispersed in THF and shows high emissions. TPM acts as the stabilizer and promotes the compatibility between the ZnO nanoparticle QDs and the PMMA matrix. After evaporation of THF from the ZnO nanoparticle QDs/PMMA composite solution, transparent polymeric hybrid films of ZnO nanoparticle QDs and PMMA are obtained. These polymeric hybrid films are characterized by photoluminescence (PL) spectroscopy, Fourier transform infrared (FT-IR) spectroscopy, transmission electron microscopy (TEM), and thermogravimetric analysis. The hybrid film exhibited a high quantum yield and PL emission under ultraviolet excitation. PL emission has been successfully tuned from blue to yellow.     

Effect of linker on the photosensitization of ZnO layers with CdSe quantum dots

In this work, zinc oxide (ZnO) nanoparticles (size <10 nm) were formed via precipitation in ethanolic solution. The zinc acetate and lithium hydroxide solutions in ethanol were mixed at 273 K temperatures under vigorous stirring. To study the effect of quantum dot (QD) coverage, we have prepared a colloidal suspension of capped CdSe QDs (size ~5 nm) by chemical route and anchored them to a nanoporous ZnO layer either by direct adsorption or through linker. Here a bifunctional molecule (mercaptopropionic acid, MPA, and thioglycolic acid, TGA) was previously adsorbed on the ZnO surface, which acted as a molecular cable. From TEM/SEM studies, it was observed that direct adsorption of CdSe QDs onto ZnO surface was not efficient. However, the bifunctional linker molecules particularly MPA facilitates binding of CdSe QDs to ZnO; and consequently, interparticle electron transfer is thus facilitated. The use of MPA linker despite of its long carbon chain also aids in the quenching of photoluminescence of CdSe on addition of ZnO in a more systematic manner indicating efficient charge transfer from CdSe into ZnO as compared with the without linker and with linker TGA case, respectively. Due to higher PL quenching and reduction in lifetime values, higher values of Stern–Volmer quenching constants were thus obtained for CdSe–ZnO composites with MPA as compared with TGA linker and without linker case, respectively. Nonlinear Stern–Volmer plots as observed for samples without linker case indicated heterogeneous quenching due to insufficient binding between CdSe QDs and ZnO. By means of spectroscopic (PL, UV–VIS, FTIR) and microscopic (TEM, SEM) techniques, we have demonstrated linker-dependent photosensitization mechanism of ZnO layers with CdSe QDs. Our data thus illustrate that interfacial-electron transfer kinetics in QD–linker–ZnO assemblies are almost independent of the length of alkyl-containing molecular linkers.     

温度对聚酰胺-胺树形分子模板法制备CdS量子点的影响

为了研究温度对聚酰胺-胺(PAMAM)树形分子的模板法制备硫化镉(CdS)量子点的影响, 以4.5代(G4.5, 64个甲酯端基)PAMAM树形分子为模板, 在－10～30 ℃的温度范围内制备了分散良好的CdS量子点. 用透射电子显微镜(TEM)表征了CdS量子点的形貌、尺寸; 用紫外-可见光谱(UV-Vis)和光致发光光谱(PL)表征了CdS量子点的光学性能. 发现在相同条件下, 制备温度从－10 ℃升高到30 ℃, CdS量子点粒径从1.8 nm增大到3.4 nm, 其中在10 ℃时制备的量子点的尺寸分布最窄; CdS量子点的吸收和发射光谱均随温度增大而红移, 其中10 ℃时制备的量子点的室温光致发光效率最高. 这表明制备温度决定了树形分子的配位基团与Cd^2＋的分离速度, 并影响了CdS量子点的成核和生长过程, 从而最终决定了CdS量子点的尺寸及尺寸分布、光致发光颜色和发光效率.     

Synthesis,characterizations, and optical properties of copper selenide quantum dots

We demonstrate the synthesis of copper selenide quantum dots (QDs) by element directed, inexpensive, straight forward wet chemical method which is free from any surfactant or template. Copper selenide QDs have been synthesized by elemental copper and selenium in the presence of ethylene glycol, hydrazine hydrate, and a defined amount of water at 70 °C within 8 h. The product is in strong quantum confinement regime, phase analysis, purity and morphology of the product has been well studied by X-ray diffraction (XRD), UV–Visible spectroscopy (UV–Vis), Photo-luminescent spectroscopy (PL), Fourier transform infrared spectroscopy (FTIR), Transmission electron microscopy (TEM), High resolution transmission electron microscopy (HRTEM), and by Atomic force microscopy (AFM) techniques. The absorption and photoluminescence studies display large “blue shift”. TEM and HRTEM analyses revealed that the QDs diameters are in the range 2–5 nm. Due to the quantum confinement effect copper selenide QDs could be potential building blocks to construct functional devices and solar cell. The possible mechanism is also discussed.     

Intercalated synthesis of zinc oxide quantum dots between multilayered organic films: preparation of 2D superlattices in colloidal solutions

Intercalation of ZnO quantum dots into two-dimensional (2D) laminated sodium lauryl sulfonate films in a colloidal solution was demonstrated. Without any substrates, hybrid films composed of a dispersed ZnO dots layer and organic films exhibit a high stability and regular 2D superlattice stacking after removal of cosurfactant molecules and water. The 2D superlattice films were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD). UV-visible absorption and photoluminescence spectra were used to investigate the growth of ZnO QDs between organic films and study their collective optical characteristics.     

Synthesis of cysteamine-coated CdTe quantum dots and its application in mercury (II) detection

High-quality cysteamine-coated CdTe quantum dots (CA-CdTe QDs) were successfully synthesized in aqueous phase by a facile one-pot method. Through hydroxylamine hydrochloride-promoted kinetic growth strategy, water-soluble CA-CdTe QDs could be obtained conveniently in a conical flask by a stepwise addition of raw materials. The photoluminescence quantum yield (PL QY) of the obtained QDs reached 9.2% at the emission peak of 520 nm. The optical property and the morphology of the QDs were characterized by UV–vis absorption spectra, photoluminescence spectra (PL) and transmission electron microscopy (TEM) respectively. Furthermore, the fluorescence of the resultant QDs was quenched by copper (II) (Cu²⁺) and mercury (II) (Hg²⁺) meanwhile. It is worthy of note that to separately detect Hg²⁺, cyanide ion could be used to eliminate the interference of Cu²⁺. Under the optimal conditions, the response was linearly proportional to the logarithm of Hg²⁺ concentration over the range of 0.08–3.33 μM with a limit of detection (LOD) of 0.07 μM.     

高质量CdSe量子点的水相制备与表征

以巯基丁二酸为稳定剂, 亚硒酸钠为硒源, 制备了高质量水溶性CdSe量子点. 研究了反应时间、 镉与硒的摩尔比及镉与巯基丁二酸的摩尔比等实验条件对CdSe量子点光谱性能的影响. 分别用紫外-可见光谱、 荧光光谱、 X射线粉末衍射和透射电子显微镜等对量子点进行表征. 结果表明, 采用这种方法制得的CdSe量子点为立方晶型, 量子点的荧光发射峰在518～562 nm范围内连续可调, 并且发射峰的半峰宽始终保持在35 nm左右, 荧光量子产率可达21%.     

氨基化单分散量子点/二氧化硅核壳纳米粒子的制备及其细胞标记

通过反向微乳液法, 在油溶性量子点表面包裹二氧化硅外壳, 使油溶性量子点水溶性化, 再利用3-氨丙基三乙氧基硅烷(APTES)在已形成的二氧化硅纳米颗粒表面进行氨基化改性, 制备富含氨基的二氧化硅包裹的量子点荧光纳米球. 通过透射电子显微镜(TEM)、粒径分析、zeta电位检测、紫外-可见分光光度、荧光分光光度和红外光谱等手段对产品进行了表征. 结果表明, 所制备的二氧化硅量子点纳米球(45 nm)具有单分散性、水溶性好及光化学稳定性强等优点. 通过静电作用, 所制备的单分散氨基化二氧化硅量子点对肿瘤细胞表面膜电荷进行了初步标记显像.     

一锅合成绿色到近红外发射的CdTe量子点

以3-巯基丙酸(MPA)为稳定剂,采用水相合成法制备了从绿色到近红外发射的CdTe量子点。系统研究了反应液pH值、镉和碲的物质的量之比及镉和3-巯基丙酸的物质的量之比等实验条件对CdTe量子点体系的发射波长和荧光量子产率的影响。在pH值为10.5,且nCd2+∶nTe2-∶nMPA=1∶0.05∶1.1的条件下,回流0.5 h,CdTe量子点体系在569 nm波长处的荧光量子产率达到30.8%;在7 h的回流时间内,制备的量子点的波长覆盖范围为525～730 nm。分别用X射线粉末衍射、透射电镜和红外光谱对CdTe量子点的晶体结构、形貌及表面基团进行表征。     

水稳定的镁掺杂ZnO量子点:一锅法合成及细胞成像应用

一锅法合成了镁掺杂的ZnO量子点,利用APTES对其进行表面包覆,并采用XRD、TEM、UV-Vis、PL和FTIR等对材料进行了表征。结果表明镁掺杂能明显增强荧光发光强度,在合适的掺杂浓度(30%)下其量子产率由11%增加到33%。通过APTES的表面包覆使镁掺杂的ZnO量子点具有良好的水溶性和荧光稳定性,可用于MCF-7细胞成像研究。     

水稳定的镁掺杂ZnO量子点:一锅法合成及细胞成像应用

一锅法合成了镁掺杂的ZnO量子点, 利用APTES对其进行表面包覆, 并采用XRD、TEM、UV-Vis、PL和FTIR等对材料进行了表征。结果表明镁掺杂能明显增强荧光发光强度, 在合适的掺杂浓度(30%)下其量子产率由11%增加到33%。通过APTES的表面包覆使镁掺杂的ZnO量子点具有良好的水溶性和荧光稳定性, 可用于MCF-7细胞成像研究。     

Fabrication and photoluminescent properties of heteroepitaxial ZnO/Zn0.8Mg0.2O coaxial nanorod heterostructures

ZnO/Zn0.8Mg0.2O coaxial nanorod heterostructures were prepared by employing catalyst-free metal-organic vapor-phase epitaxy, and their structural and photoluminescent (PL) properties were investigated using transmission electron microscopy (TEM) and temperature-dependent PL spectroscopy. TEM images show that ZnO/Zn0.8Mg0.2O layers were epitaxially grown on the entire surfaces of the ZnO nanorods and the ZnO nanorod diameters as a core material were as small as 9 +/- 2 nm. A dominant PL peak was observed at 3.316 eV, from room-temperature PL spectra of ZnO/Zn0.8Mg0.2O coaxial nanorod heterostructures with ZnO core diameters of 9 nm, indicating a PL blue shift of 30 meV, which resulted from a quantum confinement effect along the radial direction in ZnO nanorods. Furthermore, temperature-dependent PL properties of the coaxial nanorod heterostructures were investigated, showing much higher PL intensity for the coaxial nanorod heterostructures than that of bare ZnO nanorods at room temperature. The origin of the enhanced PL intensity and reduced thermal quenching for the coaxial nanorod heterostructures is also discussed.     

Microstructure-controlled aerosol-gel synthesis of ZnO quantum dots dispersed in SiO2 nanospheres

ZnO quantum dots dispersed in a silica matrix were synthesized from a TEOS:Zn(NO(3))(2) solution by a one-step aerosol-gel method. It was demonstrated that the molar concentration ratio of Zn to Si (Zn/Si) in the aqueous solution was an efficient parameter with which to control the size, the degree of agglomeration, and the microstructure of ZnO quantum dots (QDs) in the SiO(2) matrix. When Zn/Si ≤ 0.5, unaggregated quantum dots as small as 2 nm were distributed preferentially inside SiO(2) spheres. When Zn/Si ≥ 1.0, however, ZnO QDs of ～7 nm were agglomerated and reached the SiO(2) surface. When decreasing the ratio of the Zn/Si, a blue shift in the band gap of ZnO was observed from the UV/Visible absorption spectra, representing the quantum size effect. The photoluminescence emission spectra at room temperature denoted two wide peaks of deep-level defect-related emissions at 2.2-2.8 eV. When decreasing Zn/Si, the first peak at ～2.3 eV was blue-shifted in keeping with the decrease in the size of the QDs. Interestingly, the second visible peak at 2.8 eV disappeared in the surface-exposed ZnO QDs when Zn/Si ≥ 1.0.     

Low temperature synthesis of cubic phase zinc sulfide quantum dots

In this study, we report on a new method for the synthesis of ZnS quantum dots (QDs). The synthesis was carried out at low temperature by a chemical reaction between zinc ions and freshly reduced sulfide ions in ethanol as reaction medium. Zinc chloride and elemental sulfur were used as zinc and sulfur sources, respectively and hydrazine hydrate was used as a strong reducing agent to convert elemental sulfur (S₈) into highly reactive sulfide ions (S²⁻) which react spontaneously with zinc ions. This facile, less toxic, inexpensive route has a high yield for the synthesis of high quality metal sulfide QDs. Transmission electron microscopy (TEM) image analysis and selected area electron diffraction (SAED) reveal that ZnS QDs are less than 3 nm in diameter and are of cubic crystalline phase. The UV-Vis absorption spectrum shows an absorption peak at 253 nm corresponding to a band gap of 4.9 eV, which is high when compared to the bulk value of 3.68 eV revealing strong quantum confinement. PL emission transitions are observed at 314 nm and 439 nm and related to point defects in ZnS QDs.     

Effect of Al-doping on the structure and optical properties of electrospun zinc oxide nanofiber films

Electrospun ZnO precursor nanofibers of average diameters 122±64 nm, 117±44 nm and 110±39 nm were fabricated by controlling the Al concentration of a polymeric solution. The resulting nanofibers were characterized by the XRD, SEM, EDS, TEM, XPS and PL. The electrospun Al-doped ZnO nanofiber films were polycrystalline and composed of densely packed grains, with crystallite size ranging from 28.7 nm, 25.7 nm, 25.4 nm to 20.4 nm corresponding to the atomic concentration of aluminum from 0, 1.6, 2.5 to 5.8 at.%. The incorporation of aluminum resulted in a decrease trend in the grain size and lattice parameter of the ZnO nanofiber films. The room temperature PL spectra of all samples show three different emissions, including UV (ultraviolet) emission with an obvious blue shift, Vis (visible) emission and NIR (near infrared) emission, the intensity of which decreases monotonically as the doping concentration is increased except for the highest doping level. The impurity content correlates with changes in the PL spectra, and the appropriate Al doping can improve the optical properties of ZnO nanofibers. The small size effect and Al-doping or the impurity incorporation should be responsible for the blue shift observation in Al-doped ZnO nanofiber films.     

Effect of CdS Interlayer on Properties of CdTe Based Quantum Dots

Highly luminescent thioglycolic acid-capped CdTe-based core/shell quantum dots (QDs) were synthesized through encapsulating CdTe QDs in various inorganic shells including CdS, ZnS and CdZnS. CdTe/CdS core/shell QDs exhibited a significant redshift of emission peaks (a maximum emission peak of 652 nm for the core/shell QDs and 575 nm for CdTe cores) with increasing shell thickness. In contrast, the redshift of photoluminescence (PL) peak wavelength of CdTe/ZnS QDs was less than 15 nm. The PL peak wavelengths of the core/shell QDs depended strongly on core size and shell thickness. The PL quantum yields (QYs) of the CdTe/CdS core/shell QDs are up to 67 % while that of CdTe/ZnS core/shell QDs is 45 %. A composite CdZnS shell made CdTe cores a high PL QY up to 51 % and broadly adjusted PL spectra (a maximum PL peak wavelength of 664 nm). The epitaxial growth of the shell was confirmed by X-ray powder diffraction analysis and luminescence decay experiments. Because of high PL QYs, tunable PL spectra, and low toxicity from a ZnS surface layer, CdTe/CdZnS core/shell QDs will be great potential for bioapplications.     

第二近红外窗口荧光Ag2Te量子点的合成

以巯基辛烷为表面配体, 通过调控Ag前体和Te前体的比例, 制备了第二近红外窗口荧光Ag₂Te量子点. 采用透射电子显微镜(TEM)、 X射线衍射光谱(XRD)、 X射线光电子能谱(XPS)、 紫外-可见-近红外吸收光谱和荧光光谱等对产物进行了表征. 结果表明, 制得了粒径均一、 分散性好的油溶性Ag₂Te量子点, 其最大荧光发射波长位于1320 nm, 荧光量子产率高达4.2%.     

水溶性的高荧光CdTe/CdSeⅡ型核壳量子点的合成与表征

用L-半胱氨酸(L-cysteine)作为稳定剂,以制备的CdTe量子点为核模板,水相合成了具有近红外发光的Ⅱ型核壳CdTe/CdSe半导体量子点。实验考察了合成温度,核模板的尺寸和组分比等因素对合成高质量的CdTe/CdSe量子点的影响。用紫外-可见吸收和荧光光谱研究了合成的量子点的光学性质。在优化的合成条件下,荧光发射光谱在586～753nm范围连续可调,荧光量子产率高达68%;通过X-射线衍射(XRD),X射线光电子能谱(XPS)和透射电镜(TEM)对合成的Ⅱ型核壳CdTe/CdSe量子点进行了结构和形貌表征。     

1-甲基-3-(2-甲基丙烯酰乙基)-咪唑氯离子液体/ 苯乙烯无规共聚物及其CdTe量子点复合物的合成

以偶氮二异丁腈(AIBN)为引发剂, 通过自由基聚合制备了1-甲基-3-(2-甲基丙烯酰乙基)-咪唑氯离子液体和苯乙烯的无规共聚物P(MMEIM⁺Cl^--co-St). 用红外光谱、核磁共振氢谱和凝胶渗透色谱表征了共聚物的结构. 共聚物的氯仿溶液与巯基乙酸稳定的CdTe量子点水溶液混合, 通过静电相互作用复合组装, 得到澄清透明且稳定的CdTe/P(MMEIM⁺Cl^--co-St)纳米复合物的氯仿溶液. 复合物的紫外吸收光谱、荧光发射光谱和透射电子显微镜的表征结果表明, 量子点均匀分散于共聚物中, 无团聚, 且保持了量子点的荧光性能.