The influence of arrangement of St in MBS on the properties of PVC/MBS blends

Three series of MBS core-shell impact modifiers were prepared by grafting styrene and methyl methacrylate onto PB or SBR seed latex in emulsion polymerization. All the MBS modifiers were designed to have the same total chemical composition, and MMA/Bd/St equals 30/42/28, which is a prerequisite for producing transparent blends with PVC. Under this composition, there were three different ways of arrangement for styrene in MBS, which led to the different structure of MBS modifier. The concentration of MBS in PVC/MBS blends was kept at a constant value of 20 wt.%. The effects of arrangement of St in MBS on the mechanical and optical properties of PVC/MBS blends were studied. The notched Izod impact test results showed that the MBS with a PB homopolymer core grafted with St had a lowest brittle-ductile transition (BDT) temperature and BDT temperature increased with the amount of St copolymerized with Bd in the core of MBS. The transparency of blends also increased with the amount of St copolymerized with Bd in the core. TEM results showed that the arrangement of St in MBS influenced the deformation behavior. Two deformation modes were observed in the blends: cavitation and shear yielding. When all St was grafted onto the PB rubber, both cavitation and debonding were observed, which relieve the triaxial tension and promote the shear yielding of the PVC matrix. When all St was copolymerized with Bd in MBS, no cavitation could be observed and only the shear yielding of the PVC matrix took place.     

Morphology and grafting reactions in core/shell latexes

The particle morphology and percent grafting were investigated as a function of the crosslink density of the seed latex in two systems of core/shell latexes of polybutadiene/polymethyl methacrylate (PB/PMMA) and styrene–butadiene rubber/polymethyl methacrylate (SBR/PMMA) prepared by seeded emulsion polymerization at 50°C. The thin layer chromatography/flame ionization detection (TLC/FID) technique was used to characterize the grafting efficiency of the core/shell latexes. The percent grafting of the shell polymer was found to decrease with increasing the crosslink density of the core material. The particle morphology and precent grafting were also investigated as a function of composition and structure of the core material in four core/shell latex systems: polybutadiene/styrene–acrylonitrile copolymer (PB/SAN), (styrene-butadiene) random copolymer/styrene acrylonitrile copolymer (S:B/SAN), polystyrene : polybutadiene/styrene-acrylonitrile copolymer (PS:PB/SAN) and Kraton/styrene-acrylonitrile copolymer (Kraton/SAN), which were prepared by direct emulsification for the seed followed by emulsion polymerization at 70°C for the shell polymer. Grafting and crosslinking of the core material were found to be competitive reactions depending on the microstructure of the seed latex.     

Influence of elastomeric core–shell impact modifiers on mechanical properties of cellulose diacetate resin

Cellulose diacetate (CDA) plasticized with triacetine was blended by melting extrusion with two different kind of elastomeric core–shell impact modifiers: methyl methacrylate (MMA, shell) grafted onto styrene–butadiene–rubber (SBR, core) (MSBR) and MMA (shell) grafted onto butyl acrylate rubber (BAR, core) (MBAR). The different CDA/MSBR and CDA/MBAR blends were characterized by mechanical properties and morphological observation with various impact modifier contents. The highest impact strength was observed in the case of the blend with 5 wt% of MSBR and 3 wt% of MBAR, respectively. The tensile strength and Young’s modulus of CDA blends were decreased with increasing both MSBR and MBAR. According to SEM observation, MBAR was dispersed more effectively in CDA matrix than that of MSBR, thus indicating improved impact strength.     

Toughening of polyvinylchloride by core-shell rubber particles: Influence of the internal structure of core-shell particles

The work focused on the influence of the internal structure of MBS core-shell impact modifiers on the properties of PVC/MBS blends. MBS was synthesized by grafting styrene and methyl methacrylate onto PB seed latex by emulsion polymerization. Different monomer feeding manners and initiators were employed to control the internal structure of core-shell particles. The investigation of the morphology of MBS showed that when styrene monomer was fed in a semicontinuous feeding manner and redox initiator was used, core-shell particles with rarely sub-inclusions could be obtained. When preswollen manner of styrene monomer and redox initiator were employed, there were a large number of small sub-inclusions in the core of MBS. When AIBN was used as initiator, large sub-inclusions could be found in the core of MBS. The results of the Izod impact tests showed that PVC/MBS blend with MBS prepared by preswollen manner had the lowest brittle-ductile transition temperature. And TEM showed that the different internal structures of core-shell particles could lead to different deformation mechanisms. While the results of transparency tests showed that the presence of the sub-inclusions in the MBS impaired the transparency of the blends.     

Phase separation conditions for solutions of styrene copolymer with elastomer in a mixture of two monomers

This paper is concerned with incompatibility in the system styrene copolymer-elastomer-mixture of two monomers and its dependence on elastomer concentration and on composition of the styrene copolymers. At higher concentrations of SBR and of MMA in MS copolymers, there is less compatibility of MS and SBR polymers in SBR-MS-St + MMA systems. The compatibility of SBR and MS in St + MMA solutions is generally greater than for SBR and SAN in St + AN solutions. The compatibility of SBR-SAN-St + AN systems is less affected by concentrations of SBR and of AN in SAN than the compatibility of SBR-MS-St + MMA systems on the concentrations of SBR and of MMA in MS.     

Thermal behaviour of styrene butadiene rubber/poly(ethylene-co-vinyl acetate) blends

The thermal behaviour of styrene butadiene rubber (SBR)/poly (ethylene-co-vinyl acetate) (EVA) blends was studied by using thermogravimetry (TG) and differential scanning calorimetry (DSC). The effects of blend ratio, cross-linking systems and compatibilization on the thermal stability and phase transition of the blends were analyzed. It was found that the mass loss of the blends at any temperature was lower than that of the components, highlighting the advantage of blending SBR and EVA. The addition of compatibilizer was also found to improve the thermal stability. DSC studies indicated the thermodynamic immiscibility of SBR/EVA system even in the presence of the compatibilizer. This is evident from the presence of two different glass transition temperatures, corresponding to SBR and EVA phases in both compatibilized and uncompatibilized blends.     

SiO_2粒子对PMMA/SAN共混体系相分离行为的影响

采用小角激光光散射(SALLS)并结合动态流变学方法,考察了气相法二氧化硅(SiO2)粒子的加入对聚甲基丙烯酸甲酯/苯乙烯-丙烯腈无规共聚物(PMMA/SAN)共混体系相行为的影响,得到了添加SiO2粒子前后的相图,发现SiO2粒子对基体相行为的影响与基体的组成有关.对PMMA/SAN(60/40)体系,加入SiO2粒子后相分离温度上升,但并未改变相分离机理,仍为亚稳单相分解过程(spinodal decomposition,SD);而对于PMMA/SAN(30/70)体系,加入SiO2粒子后却降低了体系的相分离温度.该现象可能是SiO2粒子和基体组分界面间组成与PMMA/SAN共混物基体组成的差异造成的.     

丁苯橡胶／聚丙撑碳酸酯弹性体的结构与性能

聚丙撑碳酸酯（ＰＰＣ）是由ＣＯ２和环氧丙烷在聚合物负载的双金属催化剂作用下共聚而成的一类新型高分子材料［１］，其结构式如下：ＯＨＣＨ２ＣＨＣＨ３ＯＣＯＯｎＣＨ２ＣＨＣＨ３Ｏ］ｍＣＮＯｏＯＨ它的广泛应用对于环境保护和新资源开发具有实际意义．在...     

Effects of polybutadiene-g-SAN impact modifiers on the morphology and mechanical behaviors of ABS blends

A series of PB-g-SAN impact modifiers with different ratio of PB to SAN ranging from 20.6/79.4 to 91.9/8.1 were synthesized by seeded emulsion polymerization. ABS blends were prepared by blending these PB-g-SAN impact modifiers and SAN resin. The rubber concentration of these ABS blends was kept at a constant value of 15 wt%. The influences of different impact modifier on the mechanical behavior and morphology of ABS blends have been investigated. The dynamic mechanical analysis on ABS blends shows that T_g of the rubbery phase shifts to a lower temperature, (tan δ)_max of the rubbery phase increases and then decreases with the increase of PB concentration in PB-g-SAN impact modifier. A uniform dispersion of rubber particles in the matrix can be observed when PB/SAN ratio in PB-g-SAN impact modifier is in the range from 20.6/79.4 to 71.7/28.3. When it exceeds 71.7/28.3, an agglomeration of rubber particles occurs. The mechanical tests indicate that the ABS blend, in which PB/SAN ratio in the impact modifier is 71.7/28.3, has the maximum impact strength and yield strength.     

Morphology and mechanical and viscoelastic properties of natural rubber and styrene butadiene rubber latex blends

The morphology and mechanical and viscoelastic properties of a series of blends of natural rubber (NR) and styrene butadiene rubber (SBR) latex blends were studied in the uncrosslinked and crosslinked state. The morphology of the NR/SBR blends was analyzed using a scanning electron microscope. The morphology of the blends indicated a two phase structure in which SBR is dispersed as domains in the continuous NR matrix when its content is less than 50%. A cocontinuous morphology was obtained at a 50/50 NR/SBR ratio and phase inversion was seen beyond 50% SBR when NR formed the dispersed phase. The mechanical properties of the blends were studied with special reference to the effect of the blend ratio, surface active agents, vulcanizing system, and time for prevulcanization. As the NR content and time of prevulcanization increased, the mechanical properties such as the tensile strength, modulus, elongation at break, and hardness increased. This was due to the increased degree of crosslinking that leads to the strengthening of the 3‐dimensional network. In most cases the tear strength values increased as the prevulcanization time increased. The mechanical data were compared with theoretical predictions. The effects of the blend ratio and prevulcanization on the dynamic mechanical properties of the blends were investigated at different temperatures and frequencies. All the blends showed two distinct glass‐transition temperatures, indicating that the system is immiscible. It was also found that the glass‐transition temperatures of vulcanized blends are higher than those of unvulcanized blends. The time–temperature superposition and Cole–Cole analysis were made to understand the phase behavior of the blends. The tensile and tear fracture surfaces were examined by a scanning electron microscope to gain an insight into the failure mechanism. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2189–2211, 2000     

Shear flow effect on phase behavior and morphology in polymer blends

The effect of simple shear flow on the phase behavior and morphology was investigated for both polystyrene/poly(vinyl methyl ether) (PS/PVME) and poly(methyl methacrylate)/poly(styrene‐co‐acrylonitrile) (PMMA /SAN‐29.5) blends, which have LCST (lower critical solution temperature)‐type phase diagram. The measurements were carried out using a special shear apparatus of two parallel glass plates type. The PS/PVME blends showed shear‐induced demixing and shear‐induced mixing at low and high shear rate values, respectively. In addition, the rotation speed and the sample thickness were found to have a pronounced effect on the phase behavior under shear flow. On the‐other hand, PMMA/SAN blend showed only shear‐induced mixing and the magnitudes of the elevation of the cloud points were found to be composition and molecular weight dependent. The morphology of the PMMA/SAN=75/25 blend indicated that shear‐induced mixing occurred at a critical shear rate value, below which the two phases were highly oriented and elongated in the flow direction.     

Filler‐polymer interactions of styrene and butadiene units in silica‐filled styrene–butadiene rubber compounds

Styrene–butadiene rubber (SBR) is a copolymer of styrene and butadiene, and the butadiene unit is composed of cis‐1,4‐, trans‐1,4‐, and 1,2‐components. Filler‐polymer interactions of each component of SBR in silica‐filled SBR compounds were examined by microstructure analysis of the bound and unbound rubbers. The composition ratio of butadiene and styrene units (butadiene/styrene) of the bound rubber was higher than that of the compounded rubber. Of the butadiene units, the 1,2‐component of the bound rubber was more abundant than the cis‐1,4‐ and trans‐1,4‐components. The filler‐polymer interaction of the butadiene unit with silica was stronger than that of the styrene unit, and the interaction of the 1,2‐component was stronger as compared with the others. The butadiene–styrene ratio of the bound rubber of the compounds containing the silane coupling agent was lower than for the compounds without the silane. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 577–584, 2004     

Effect of reactive compatibilization on the properties of poly(butylene terephthalate)/acrylonitrile–ethylene–propylene–diene–styrene blends

Blends of poly(butylene terephthalate) (PBT) with 30 wt % acrylonitrile–ethylene–propylene–diene–styrene (AES) were prepared with methyl methacrylate (MMA)/glycidyl methacrylate (GMA)/ethyl acrylate (EA) terpolymers (MGEs) as compatibilizing agents. These acrylic terpolymers were miscible with the styrene–acrylonitrile (SAN) phase of AES, whereas the epoxide groups of GMA could react with the PBT end groups; this could lead to the formation of grafted copolymers (PBT‐g‐MGE) at the PBT/AES interface during the melt processing of the blends if at least a fraction of this interface was formed between the PBT and SAN phases. This study found evidence of the aforementioned interfacial structure through the effectiveness of the MGE terpolymers in promoting the compatibilization, as evaluated by dynamical mechanical analysis, through the increase in the viscosity of the blends, and through the reduction of the AES particle size dispersed in the PBT matrix. These effects became more intense with an increase in the overall concentration of GMA in the blends and with a reduction of the molecular weight of MGE. Another effect promoted by the compatibilization was a remarkable reduction of the brittle–ductile transition temperatures of the blends, which was correlated with the reduction of the AES particle size. However, this correlation between the brittle–ductile transition temperatures and particle size did not hold for the blend with the lowest AES particle size, which showed a high ductile–brittle transition temperature. These mechanical behaviors were examined on the basis of the current theory of the toughening of thermoplastics, which takes into account the importance of the rubber interparticle distance and the cavitation process of these particles. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1244–1259, 2005     

Effect of PBT molecular weight and reactive compatibilization on the dispersed‐phase coalescence of PBT/SAN blends

Poly(butylene terephthalate) (PBT)/styrene‐acrylonitrile copolymer (SAN) blends were investigated with respect to their phase morphology. The SAN component was kept as dispersed phase and PBT as matrix phase and the PBT/SAN viscosity ratio was changed by using different PBT molecular weights. PBT/SAN blends were also compatibilized by adding methyl methacrylate‐co‐glycidyl methacrylate‐co‐ethyl acrylate terpolymer, MGE, which is an in situ reactive compatibilizer for melt blending. In noncompatibilized blends, the dispersed phase particle size increased with SAN concentration due to coalescence effects. Static coalescence experiments showed evidence of greater coalescence in blends with higher viscosity ratios. For noncompatibilized PBT/SAN/MGE blends with high molecular weight PBT as matrix phase, the average particle size of SAN phase does not depend on the SAN concentration in the blends. However noncompatibilized blends with low molecular weight PBT showed a significant increase in SAN particle size with the SAN concentration. The effect of MGE epoxy content and MGE molecular weight on the morphology of the PBT/SAN blend was also investigated. As the MGE epoxy content increased, the average particle size of SAN initially decreased with both high and low molecular weight PBT phase, thereafter leveling off with a critical content of epoxy groups in the blend. This critical content was higher in the blends containing low molecular weight PBT than in those with high molecular weight PBT. At a fixed MGE epoxy content, a decrease in MGE molecular weight yielded PBT/SAN blends with dispersed nanoparticles with an average size of about 40 nm. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

Rheological,mechanical and morphological properties of thermoplastic vulcanizates based on NR‐g‐PMMA/PMMA blends

Graft copolymer of natural rubber and poly(methyl methacrylate) (NR‐g‐PMMA) was prepared using semi‐batch emulsion polymerization technique via bipolar redox initiation system. It was found that the grafted PMMA increased with the increase of methyl methacrylate (MMA) concentration used in the graft copolymerization. The NR‐g‐PMMA was later used to prepare thermoplastic vulcanizates (TPVs) by blending with PMMA through dynamic vulcanization technique. Conventional vulcanization (CV) and efficient sulphur vulcanization (EV) systems were studied. It was found that the CV system provided polymer melt with lower shear stress and viscosity at a given shear rate. This causes ease of processability of the TPVs via extrusion and injection molding processes. Furthermore, the TPVs with the CV system showed higher ultimate tensile strength and elongation. The results correspond to the morphological properties of the TPVs. That is, finer dispersion of the small vulcanized rubber particles were observed in the PMMA matrix. Various blend ratios of the NR‐g‐PMMA/PMMA blends using various types of NR‐g‐PMMA (i.e. prepared using various percentage molar ratios of NR and MMA) were later studied via dynamic vulcanization by a conventional sulphur vulcanization system. It was found that increasing the level of PMMA caused increasing trend of the tensile strength and hardness properties but decreasing level of elongation properties. Increasing level of the grafted PMMA in NR molecules showed the same trend of mechanical properties as in the case of increasing concentration of PMMA used as a blend component. From morphological studies, two phase morphologies were observed with a continuous PMMA phase and dispersed elastomeric phase. It was also found that more finely dispersed elastomeric phase was obtained with increasing the grafted PMMA in the NR molecules. Copyright © 2005 John Wiley & Sons, Ltd.     

Transition from crazing to shear deformation in ABS/PVC blends

ABS/PVC blends were prepared over a range of compositions by mixing PVC, SAN, and PB‐g‐SAN. All samples were designed to have a constant rubber level of 12 wt % and the ratio of total‐SAN to PVC in the matrix of the blends varied from 70.5/17.5 to 18/80. Transmission electron microscope and scanning electron microscope have been used to study deformation mechanisms in the ABS/PVC blends. Several different types of microscopic deformation mechanisms, depending on the composition of blends, were observed for the ABS/PVC blends. When the blend is a SAN‐rich system, the main deformation mechanisms were crazing of the matrix. When the blend is a PVC‐rich system, crazing could no longer be detected, while shear yielding of the matrix and cavitation of the rubber particles were the main mechanisms of deformation. When the composition of blend is in the intermediate state, both crazing and shear yielding of matrix were observed. This suggests that there is a transition of deformation mechanism in ABS/PVC blends with the change in composition, which is from crazing to shear deformation. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 687–695, 2006     

Silicone‐based impact modifiers for poly(vinyl chloride), engineering resins,and blends

Silicone‐based impact modifiers were prepared in a previous study. The modifiers were composed of silicone/acrylic rubber cores and grafted acrylic shells. They improved the toughness of poly(vinyl chloride) (PVC) and poly(methyl methacrylate). The silicone emulsion that was used to produce the silicone‐based impact modifiers was prepared via two routes: emulsion polymerization and bulk polymerization of octamethyltetracyclosiloxane. Many silicone‐based impact modifiers were produced that had different silicone/acrylic rubber characteristics. Through a toughness examination of modified PVC, the best composition of the silicone‐based impact modifiers was obtained, and the silicone content in the rubber composition was 25 wt %. The morphology of the silicone‐based impact modifiers, determined by transmission electron microscopy, was as follows: core and second shell polymers were mainly poly(butyl acrylate), and the first shell polymer was silicone. The silicone‐based impact modifiers were blended with engineering resins such as PVC, polycarbonate (PC), poly(butylene terephthalate) (PBT), and PC/PBT mixtures. The impact strength under standard conditions and after weathering test conditions for blends of the silicone‐based impact modifiers were investigated with respect to two commercially available acrylic and methyl methacrylate/butadiene/styrene impact modifiers. The results showed good weatherability and good toughness under low‐temperature conditions for the silicone‐based impact modifiers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1112–1119, 2004     

Morphology dependence of crystallization of natural rubber in blends

Crystallization of natural rubber (NR) was investigated in different morphology for NR/styrene butadiene rubber (SBR) blend and NR/polystyrene-(b)-polyisoprene (SI)/polystyrene (PS) blend. A purified NR (PC-TE) was prepared from pale crape via transesterification. In the blends, PC-TE formed various morphologies; that is, matrix phase, island phase and continuous phase with a nano-scale, respectively, in dependence upon the ratio of the rubbers. The crystallization rate of the blends was also significantly associated with the morphology of the rubbers.     

Identifying the effect of aromatic oil on the individual component dynamics of S‐SBR/BR blends by broadband dielectric spectroscopy

Miscible S‐SBR (solution styrene–butadiene copolymer)/BR (polybutadiene homopolymer) blends are used in multiple applications like modern passenger car tire treads. Despite their miscibility, there is a problem to predict tire performance due to dynamical heterogeneities present in the S‐SBR/BR blends. On the one hand, S‐SBR/BR blends have a thermorheologically complex behavior, which complicates the prediction of the temperature‐ and frequency‐dependence of material properties. On the other hand, due to differences in the polarity of the individual components, the extender oils used in the elastomeric compounds could distribute unequally within the blends, where little is known about how oils interact with the two polymers. In this work a combination of Differential Scanning Calorimetry, Dynamic Mechanical Analysis, and Broadband Dielectric Spectroscopy (BDS) is used to clarify: (i) the thermorheological complexity of S‐SBR/BR blends, (ii) the effect of the extender oil on the blend. The broad frequency operation of BDS allows for the analysis of the S‐SBR and BR component dynamics and the effect of the oil on each of them within an S‐SBR/BR (50/50) blend. Based on the discretization of individual component dynamics in the blend, conclusive remarks are made on the effect of the extender oil for either component in the blend. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 842–854