水性聚氨酯/功能化石墨烯纳米复合材料的非等温结晶动力学

采用差示扫描量热法DSC研究了水性聚氨酯/功能化石墨烯(WPU/FGNs)纳米复合材料的非等温结晶行为,分别采用Ozawa方程、莫志深方程研究复合材料的非等温结晶动力学,并通过Kissinger方程计算了结晶过程中的活化能。 结果表明,石墨烯在复合材料的结晶过程中起到异相成核剂的作用,提高了复合材料的结晶起始温度、峰值温度和结晶速率;增加石墨烯的质量分数,复合材料的结晶维数增加;石墨烯增加至0.3%,复合材料的活化能从-47.74 kJ/mol降低至-53.60 kJ/mol,继续增加石墨烯至1.0%,复合材料的活化能增加至-41.74 kJ/mol。     

Polyaniline‐coupled graphene/nickel hydroxide nanohybrids as flame retardant and smoke suppressant for epoxy composites

Graphene‐polyaniline/nickel hydroxide ternary hybrid (RGO‐PANI/Ni(OH)₂) was synthesized and incorporated into epoxy resin (EP) to improve the fire retardant property. Thermogravimetric analysis results showed that the RGO‐PANI/Ni(OH)₂ nanohybrid could catalyze the thermal degradation of epoxy matrix that was essential to trigger the char formation. The char yield of the RGO‐PANI/Ni(OH)₂/EP composite was improved compared with that of the samples with graphene and polyaniline only. With 3.0‐wt% RGO‐PANI/Ni(OH)₂, significant reduction in peak heat release rate (40%) and peak smoke production rate (36%) was observed in the cone calorimeter tests. Thermogravimetric analysis/infrared spectrometry (TG‐IR) results indicated that the flammable volatiles of the RGO‐PANI/Ni(OH)₂/EP composite was reduced compared with those of the EP and RGO‐PANI/EP. The superior flame retardant and smoke suppressant behaviors of the RGO‐PANI/Ni(OH)₂ nanohybrid over RGO‐PANI were attributed to the combination of good barrier effect of graphene with catalytic ability of char formation of PANI and metal hydroxide.     

Strong covalent bonding modulated graphene oxide/epoxy interfacial enhancement and advanced corrosion resistance

Abstract

Chemically functionalized graphene oxide [multi-amino functionalized graphene oxide (MAGO)] was achieved by building covalent bonds between graphene oxide (GO) and a small molecule containing benzene structure and multi-amino groups. Fourier transform infrared, X-ray diffraction, X-ray photo electron spectroscopy and TEM-EDX results certified that the molecule was successfully grafted onto GO nanosheets. Subsequently, functionalized GO was incorporated into waterborne epoxy (EP) coating through ball-milling method. This molecular design can significantly improve the dispersion of MAGO in EP matrix, as well as the compatibility and interaction between MAGO and EP. Compared with GO/EP, the water absorption of MAGO/EP decreased from 4.38 to 2.59%, the adhesion strength of MAGO/EP increased from 4.72 to 6.32?MPa after immersion of 40?days in 3.5% NaCl solution. Incorporation of 1?wt% of MAGO into EP matrix prominently improved the long-term corrosion resistance. The impedance modulus of GO/EP coating decreased by four orders after 40 days immersion, while that of MAGO/EP coating only decreased by one order. The impedance modulus was still 1.47?×?10⁸ Ω cm², and two-time constant wasn’t detected for MAGO/EP coating. This research developed a novel green anticorrosion coating with enhanced durability for metal protection.     

The influence of mesoporous SiO2‐graphene hybrid improved the flame retardancy of epoxy resins

A novel mesoporous SiO₂‐graphene nanohybrid was successfully synthesized by a 1‐pot hydrothermal synthesis method using tetraethylortho silicate and graphene oxide as initial materials to improve the dispersion of graphene in epoxy matrix. Subsequently, the SiO₂‐graphene nanohybrids were added into epoxy resin to investigate their fire behaviors. It was found that the incorporation of the as‐prepared SiO₂‐graphene nanohybrids into epoxy resin obviously increased the flame retardancy, compared with those of neat epoxy. This attractive feature of SiO₂‐graphene epoxy nanocomposites was attributed to the barrier effect as well as the labyrinth effect contributed by SiO₂‐graphene in EP resin.     

Viscoelastic response and interlaminar delamination resistance of epoxy/glass fiber/functionalized graphene oxide multi-scale composites

Graphene oxide (GO) was functionalized using three different diamines, namely ethylenediamine (EDA), 4,4′-diaminodiphenyl sulfone (DDS) and p-phenylenediamine (PPD) to reinforce an epoxy/glass fiber (EP/GF) composite laminate, with the aim of improving the overall composite mechanical performance. Different mechanical characterization techniques were used to determine the mechanical performance, including: tensile stress strain, double cantilever beam (DCB) mode-I fracture toughness and dynamic mechanical thermal analysis (DMTA). Scanning electron microscopy (SEM) was used to support the results and conclusions. The results demonstrated remarkable enhancements in the mechanical performance of EP/GF composite laminates by incorporation of functionalized graphene oxide (FGO) nanofiller, whilst the mechanical performance of the GO reinforced composite only improved marginally. Finally, the mechanical performance of the EP/GF/FGO multi-scale composites was found to be dependent on the type of FGO functional groups; of which EDA exhibited the highest performance. These investigations confirmed that the EDA-FGO-reinforced EP/GF composites possess excellent potential to be used as multifunctional engineering materials in industrial applications.     

Investigation of free volume and the interfacial,and toughening behavior for epoxy resin/rubber composites by positron annihilation

An epoxy resin (EP) matrix has been modified with carboxyl-randomized butadiene-acrylonitrile (CRBN) rubber and hydroxyl-terminated butadiene-acrylonitrile rubber (HTBN). When the rubber content was low (⩽5%), the free volume size varied slowly, meanwhile, the free volume size of EP/HTBN system was smaller than EP/CRBN system. With further addition of rubber component (⩾7%), the free volume size of the composite increased quickly. In this case, the free volume size of EP/HTBN system was larger than EP/CRBN system. The intermediate positron lifetime component (I₂) was affected by the structure of the interface layer between rubber particles and EP matrix. The different free volume properties could be attributed to the compatibility between rubber and EP.     

有机磷系及石墨烯阻燃环氧树脂研究进展

环氧树脂作为一种优异的树脂基体,被广泛地应用于众多领域,但因其极易燃烧,所以常常需要对其进行阻燃处理。本文简要综述了近几年有机磷系化合物及石墨烯阻燃环氧树脂的研究进展,其中有机磷系化合物阻燃部分重点介绍了以阻燃剂中间体9,10-二氢-9-氧杂-10-磷杂菲-10-氧化物(DOPO)及其衍生物和聚磷酸铵(APP)为代表的含磷阻燃剂在环氧树脂中的阻燃机理和阻燃进展;同时也介绍了石墨烯及其衍生物在环氧树脂阻燃领域的最新研究进展,并对其发展前景进行了展望。     

Reactive copolymer functionalized graphene sheet for enhanced mechanical and thermal properties of epoxy composites

Uniform dispersion of graphene nanosheets (GNS) in a polymer matrix with strong filler–matrix interfacial interaction, preserving intrinsic material properties of GNS, is the critical factor for application of GNS in polymer composites. In this work, a novel reactive copolymer VCz–GMA containing carbazole and epoxide group was designed, synthesized and employed to noncovalently functionalize GNS for preparing epoxy nanocomposites with enhanced mechanical properties. The presence of carbazole groups in VCz–GMA enables the tight absorption of copolymer on to graphene surface via π–π stacking interaction, as evidenced by Raman and fluorescence spectroscopy, whereas the epoxide segments chemically reacts with the epoxy matrix, improving the compatibility and interaction of graphene with epoxy matrix. As a result, the VCz–GMA–GNS/epoxy composite showed a remarkable enhancement in both mechanical and thermal property than either the pure epoxy or the graphene/epoxy composites. The incorporation of 0.35 wt % VCz–GMA–GNS yields a tensile strength of 55.72 MPa and elongation at break of 3.45, which are 42 and 191% higher than the value of pure epoxy, respectively. Increased glass transition temperature and thermal stability of the epoxy composites were also observed. In addition, a significant enhancement in thermal conductivity was achieved with only 1 wt % VCz–GMA–GNS loading. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2776–2785     

Influence of surface modified graphene oxide on the mechanical performance and curing kinetics of epoxy resin

In this study, the hyperbranched polyester were successfully grafted onto graphene oxide (GO). The mechanical performance and curing kinetics of epoxy resin (EP), EP/ graphene oxide (EP/GO), and EP/ hyperbranched polyester grafted GO (EP/GO‐B) were investigated by means of mechanical tests and differential scanning calorimetry (DSC). Results revealed that the presence of GO lowered the cure temperature and accelerated the curing of EP, and the addition of GO‐B exhibited a stronger effect in accelerating the cure of EP compared with GO. Activation energies were calculated using Kissinger approach, and Ozawa approach, respectively. Results revealed lowered activation energy after the addition of GO or GO‐B at low degrees of cure, indicating that GO had a large effect on the curing reaction. The presence of GO facilitated the curing reaction, especially the initial epoxy‐amine reaction. Moreover, GO‐B exhibited better performance. Related mechanism was proposed.     

Synthesis of novel epoxy-group modified phosphazene-containing nanotube and its reinforcing effect in epoxy resin

In this work, novel epoxy-group modified phosphazene-containing nanotubes (EPPZTs) were successfully synthesized through the reaction between epichlorohydrin and phosphazene-containing nanotubes with active hydroxyl groups. The structure was characterized by Fourier transform infrared spectroscopy (FTIR) and the morphology was investigated by scanning electron microscopy (SEM). EPPZTs/epoxy resin composites were prepared by introducing EPPZTs into epoxy resin matrix (EP618). Impact strength and tensile strength of the composites with different content of EPPZTs were tested and SEM was used to study the dispersion of EPPZTs in polymer matrix. The best effect in reinforcing the matrix was observed when the content of EPPZTs was 0.1%. The thermal stability of the composites was studied by thermo gravimetric analysis (TGA) and it was found that the addition of EPPZTs effectively increased the residue and decreased the weight loss rate.     

Effects of noncovalently functionalized multiwalled carbon nanotube with hyperbranched polyesters on mechanical properties of epoxy composites

In order to improve the dispersibility and interface properties of multi-walled carbon nanotubes (MWCNTs) in epoxy resin (EP), aromatic hyperbranched polyesters with terminal carboxyl (HBP) and aromatic hyperbranched polyesters with terminal amino groups (HBPN) were used for noncovalent functionalization of MWCNTs. Epoxy composites reinforced by different types of MWCNT were prepared. The effects of noncovalent functionalization of MWCNTs on the dispersibility, wettability, interface properties and mechanical properties of epoxy composites were investigated. The results show that the dispersibility and wettability of MWCNTs are significantly improved after noncovalent functionalization. A large number of terminal primary amines (NH₂) on noncovalently functionalized MWCNT with HBPN (HBPN-MWCNT) form covalent bonds with EP matrix, and thus the interfacial adhesion is enhanced significantly, resulting in high load transfer efficiency and substantial increase in mechanical properties. The interface with covalent bonding formed between the flexible hyperbranched polyester layer on the surface of HBPN-MWCNT and the EP matrix promotes plastic deformation of the surrounding EP matrix. The toughening mechanisms of HBPN-MWCNT are MWCNT pull-out and a large amount of plastic deformation of the surrounding EP matrix.     

Viscoelastic properties and morphology of dicyanate ester/epoxy co-polymers modified with polysiloxane and butadiene–acrylonitrile rubbers

Dynamic mechanical analysis was conducted on specimens prepared from cyanate ester (CE) and epoxy (EP) resins cured together at various mass compositions. Increase of amount of epoxy resin in composition was shown to have a disadvantageous effect on glass transition temperature (T _g). It was shown that post-curing procedure was needed to produce a polymer matrix with a single glass transition relaxation, but increase in post-cure temperature up to 250 °C resulted in slight reduction in T _g for epoxy/cyanate copolymers. TG results proved that the presence of epoxy resin reduces thermal stability of the cyanate/epoxy materials. The neat CE and EP/CE systems containing 30 wt% of epoxy resin were modified using epoxy-terminated butadiene–acrylonitrile rubber (ETBN) and polysiloxane core–shell elastomer (PS). The scanning electron microscopy (SEM) results showed the existence of second phase of ETBN and PS modifiers. Only in the case of EP/CE composition modified with ETBN, well-dispersed second phase domains were observed. Analysis of SEM images for other CE- and EP/CE-modified systems revealed the formation of spherical aggregates.     

Effect of the C/O ratio in graphene oxide materials on the reinforcement of epoxy-based nanocomposites

The effect of the C/O ratio of graphene oxide materials on the reinforcement and rheological percolation of epoxy-based nanocomposites has been studied. As-prepared graphene oxide (GO) and thermally-reduced graphene oxide (TRGO) with higher C/O ratios were incorporated into an epoxy resin matrix at loadings from 0.5 to 5 wt %. Tensile testing revealed good reinforcement of the polymer up to optimal loadings of 1 wt %, whereas agglomeration of the flakes at higher loadings caused the mechanical properties of the composites to deteriorate. The level of reduction (C/O) of the graphene oxide filler was found to influence the mechanical and rheological properties of the epoxy composites. Higher oxygen contents were found to lead to stronger interfaces between graphene and epoxy, giving rise to higher effective Young's moduli of the filler and thus to superior mechanical properties of the composite. The effective modulus of the GO in the nanocomposites was found to be up to 170 GPa. Furthermore, rheological analysis showed that highly oxidized graphene flakes did not raise the viscosity of the epoxy resin significantly, facilitating the processing considerably, of great importance for the development of these functional polymeric materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 281–291     

Direct diazotization of graphite nanoplatelets with melamine and their favorable application in epoxy resins

The ease of undesirable agglomeration and a low efficiency are two problems that restrict the application of graphite nanoplatelets (GNPs) in epoxy resins (EP). Herein, a new strategy with melamine (MEL) as the precursor to functionalize GNPs chemically, which form a bonding layer that is compatible with epoxy matrix, is reported. The MEL fragments with secondary amine groups were grafted uniformly on the GNPs surface by covalent junctions to exploit the diazonium chemistry. This behavior led to a better dispersion and a stronger interaction with the epoxy matrix and resulted in an enhanced glass transition temperature and bending strength, compared with the pure EP. When only 1 wt% functionalized GNPs (f‐GNPs) was used, the Tg of the modified EP raised of about 15°C compared with pure EP, and the bending strength increased by approximately 39%. The dielectric constant of the EP with f‐GNPs was impacted slightly, and the dielectric loss decreased. At 10⁵ Hz, the dielectric loss of the EP with 1 wt% f‐GNPs decreased by approximately 11% compared with pure EP. Therefore, diazotization modification of the GNPs is a useful approach to improve the compatibility in nanoparticle networks.     

聚氨酯/环氧树脂IPN复合抛光材料的制备及性能研究

本研究采用聚氨酯与环氧树脂(PU/EP)作为胶黏剂形成互穿网络(IPN),以无机磨料和稀土抛光剂为分散相,通过一定的成型工艺制备成复合抛光材料。通过固化前后的红外光谱,分析了PU、EP两者之间的反应;热重分析表明PU/EP IPN复合抛光材料的耐热性能比纯的PU和EP有显著提高;体视显微镜照片显示该复合抛光材料具有微孔结构;力学及应用性能研究显示当胶黏剂含量为25%时性能最佳;且在PU/EP=2时,抛光后的玻璃透光率保持原有的97%,且耐磨性得到大幅度提高。     

Rice Husk‐derived Hierarchical Micro/Mesoporous Carbon–Silica Nanocomposite as Superior Filler for Green Electronic Packaging Material

In this study, a carbon‐controllable hierarchical micro/mesoporous carbon–silica material derived from agricultural waste rice husk was easily synthesized and utilized as filler in an epoxy matrix for electronic packaging applications. Scanning electron microscopy, thermogravimetric analysis, and N₂ adsorption/desorption isotherms were used to characterize the morphology, thermal stability, carbon content, and porous structural properties, respectively, of the as‐obtained carbon–silica material, namely rice husk char (RHC ). As a filler material, the uniformly dispersed RHC filler in the epoxy/RHC composite was easily prepared through hydrogen bonding of the silanol group of silica with the epoxy matrix. For electronic packaging applications, the thermal conductivity and thermomechanical properties (storage modulus and coefficient of thermal expansion) of the epoxy/RHC composites improved with increasing carbon content. Moreover, loading of the 40% RHC filler substantially enhanced the storage modulus of the epoxy/RHC composite (5735 MPa ) compared to the epoxy with 40% commercial silica filler (3681 MPa ). Considerable commercial potential is expected for the carbon–silica composite because of the simple synthesis process and outstanding performance of the prepared packaging material.     

纳米LDH对环氧树脂燃烧的抑烟作用

水滑石;阻燃;纳米LDH对环氧树脂燃烧的抑烟作用     

Pyrolysis and fire behaviour of epoxy resin composites based on a phosphorus-containing polyhedral oligomeric silsesquioxane (DOPO-POSS)

The pyrolysis and fire behaviour of epoxy resin (EP) composites based on a novel polyhedral oligomeric silsesquioxane containing 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO-POSS) and diglycidyl ether of bisphenol A (DGEBA) have been investigated. The pre-reaction between the hydroxyl groups of DOPO-POSS and the epoxy groups of DGEBA at 140 °C is confirmed by FTIR, which means that DOPO-POSS molecules of hydroxyl group could easily disperse into the epoxy resin at the molecular level. The EP composites with the DOPO-POSS were prepared through a curing agent, m-phenylenediamine (m-PDA). The morphologies of the EP composites observed by SEM indicate that DOPO-POSS disperses with nano-scale particles in the EP networks, which implies good compatibility between them. The thermal properties and pyrolysis of the EP composites were analyzed by DSC and TGA, TGA-FTIR, and TGA-MS. The analysis indicates that the DOPO-POSS change the decomposition pathways of the epoxy resin and increase its residue at high temperature; moreover, the release of phosphorous products in the gas phase and the existence of Si-O and P-O structures in the residue Is noted. The fire behaviour of the EP composites was evaluated by cone calorimeter (CONE). The CONE tests show that incorporation of DOPO-POSS into epoxy resin can significantly improve the flame retardancy of EP composites. SEM and XPS were used to explore micro-structures and chemical components of the char from CONE tests of the EP composites, they support the view that DOPO-POSS makes the char strong with the involvement of Si-O and P-O structures.     

Voltammetric Determination of Epinephrine in the Presence of Uric Acid Based on Aminated Graphene and Ag NPs Hybrid Membrane Modified Electrode

A hybrid membrane consisted of aminated graphene and Ag nanoparticles（Ag NPs） was prepared on the surface of glassy carbon electrode（GCE） by cyclic voltammetry（CV） with aminated graphene（GR-NH2） as matrix for immobilizing Ag NPs.The morphology and electrochemical properties of this hybrid membrane were characterized by scanning electron microscopy（SEM） and CV,respectively,and on this membrane,the voltammetric behaviors of epinephrine（EP） were studied in detail.The membrane exhibited excellent eletro-catalytic activities for the redox of EP,and could resolve the electrochemical response of EP and uric acid（UA） into two oxidation peaks.The peak current of EP was linear with its concentration in the ranges of 0.916-18.3 μmol/L and 18.3-184 μmol/L.The detection limit was 2.0 nmol/L（S/N=3）.The proposed modified electrode retained the advantages of easy fabrication,high sensitivity and good repeatability for the determination of EP.     

Environmentally benign green composites based on epoxy resin/bacterial cellulose reinforced glass fiber: Fabrication and mechanical characteristics

Bio-based bacterial cellulose (BC) epoxy composites were manufactured and their mechanical properties were examined. The BC was initially fabricated from Vietnamese nata de coco by means of alkaline pretreatment followed by solvent exchange. The obtained fibers were dispersed in epoxy resin (EP) by both mechanical stirring and ultrasonic techniques. The resulting blend was used as the matrix for glass-fiber (GF) composite fabrication using a prepreg method followed by multiple hot-press-curing steps. The morphology, mechanical characteristics and mode-I interlaminar fracture toughness of the fabricated composites were investigated. With a 0.3-wt% BC content, the mode-I interlaminar fracture toughness for both crack initiation and crack propagation were improved by 128.8% and 1110%, respectively. The fatigue life was dramatically extended by a factor of 12, relative to the unmodified composite. Scanning electron microscopy images revealed that the BC plays a vital role in increasing the interlaminar fracture toughness of a GF/EP composite via the mechanisms of crack reflection, debonding and fiber-bridging.