On-line coupling of supercritical fluid extraction with high-performance liquid chromatography for the determination of explosives in vapour phases

An investigation into the selectivity of an iminodiacetic acid (IDA) modified silica gel column for transition and heavy metal ions using non-chelating inorganic eluents has been carried out. A number of eluent parameters were investigated to determine the exact retention mechanism taking place and to control selectivity. The parameters studied were eluent ionic strength and the nature of the inorganic salt used, eluent pH and eluent temperature. The results obtained showed how despite certain metal ions exhibiting similar stability constants with the bonded IDA groups, careful control of each of the above parameters, in particular eluent chloride ion concentration and eluent temperature, could result in large changes in selectivity. Optimal conditions for the isocratic and gradient separation of Mg(II), Ca(II), Mn(II), Cd(II), Co(II), Zn(II) and Pb(II) were determined. An isocratic method using a 0.035 M KCl, 0.065 M KNO3 (pH 2.5) eluent was successfully applied to the determination of Mn(II), Cd(II), Co(II) and Zn(II) at concentrations between 20 and 121 microg/l in a freshwater certified reference material (NIST 1640).     

Determination of trace alkaline earth metals in brines using chelation ion chromatography with an iminodiacetic acid bonded silica column

The chromatographic behaviour of alkaline earth metals on iminodiacetic acid bonded silica was studied. It was found that the ionic strength of the eluent greatly affected both retention time and selectivity by controlling the extent to which either simple ion exchange or surface complexation was responsible for retention. With a 0.1 M KNO3 eluent, the retention order was Mg(II), Sr(II), Ca(II) and Ba(II), indicating a strong contribution to retention from ion exchange. However, when using a 1.5 M KNO3 eluent, Ba(II) was found to elute first, indicating complexation to be more dominant under these conditions (pH 4.2). The effect of the ionic strength of the sample was also studied and it was found that by matching the eluent cation with that of the sample matrix, efficient separations of alkaline earth metals in 1.0 M NaCl and KCl brines could be obtained without matrix system peaks. Using post-column reaction with o-cresolphthalein complexone, trace levels of Ca(II) and Mg(II) were determined in medicinal NaCl saline solution and laboratory-grade KCl.     

Iminodiacetic acid functionalised monolithic silica chelating ion exchanger for rapid determination of alkaline earth metal ions in high ionic strength samples

Iminodiacetic acid has been covalently bonded to a bare silica monolith to produce the first reported high-performance monolithic chelating ion exchange column. Using the new column, separation and determination of traces of alkaline earth metal ions (low ppm) in high ionic strength samples (up to 2 M NaCl and KCl brines), could be achieved in under 40 s. At an eluent flow rate of 4 mL min(-1) retention time precision was < 1.2% (n = 9) for Mg(II) and Ca(II), with detector linearity (n = 5) over the range 2-10 mg L(-1) of between R2 = 0.985 and R2 = 0.995. In 1 M KCl and NaCl brine samples, detection limits of 0.2 mg L(-1) were possible.     

Ion exchange properties of monolithic and particle type iminodiacetic acid modified silica

A 10 cm silica monolith has been modified with iminodiacetic acid (IDA) groups and characterised for its selectivity toward alkali, alkaline earth, and selected transition metal cations. Physical characterisation of the modified monolith found non-homogeneous modification along the length of the monolith, although sufficient capacity was achieved to facilitate significant retention of alkaline earth and transition/heavy metal ions over a range of eluent pH and ionic strength conditions. For alkaline earth and transition/heavy metal ions, selectivity of the 10 cm IDA monolith closely matched that seen with a 25 cm IDA modified silica gel particle packed column, although the separation of alkali metal ions was noticeably poorer on the monolithic column. Peak efficiencies for most metal ions were of a similar order for both column types, except for Zn(II), which showed significant peak broadening on the IDA monolithic column.     

Retention behavior of alkali, alkaline earth and transition metal cations in ion chromatography with an unmodified silica gel column

An unmodified silica gel (Develosil 30-5) column (150×4.6 mm I.D.) has been applied to the ion chromatographic separation of alkali, alkaline earth and transition metal cations. The retention behavior of the above cations on the bare substrate was investigated using a number of weak inorganic and organic acid eluents. During this investigation, several separations were achieved and the most suitable eluent conditions were identified. It was concluded that: (a) 1.5 mM HNO₃-0.5mM pyridine-2,6-dicar☐ylic acid eluent was the most effective for the simultaneous separation of common alkali and alkaline earth metal cations, (b) 1.5 mM oxalic acid eluent resulted in the best separation of alkali, alkaline earth, and transition metal cations, (c) 0.5 mM CuSO₄ eluent could be used for the separation of alkali metal cations alone and (d) 0.5 mM ethylenediamine-oxalic acid eluent at pH 5.5 resulted in themost efficient separation of both alkaline earth and transition metal cations.     

Simultaneous ion-chromatography of alkali, alkaline earth and heavy metal ions with conductivity and indirect UV detection: Comparison of eluents containing organic complexing acids and copper sulfate

Summary The simultaneous ion-chromatography of mono-and divalent metal ions on the weak cation-exchange column Nucleosil-PBDMA (polymer coated silica with polybutandiene-maleic acid) with conductivity and indirect UV-detection is presented. The influences of eluents containing organic complexing acids (-hydroxy-isobutyric, tartaric, citric, oxalic, pyridine-2,6-dicarbonic acid and EDTA etc.) as well as UV-absorbing, displacing counterions [Cu(II), Ce(III) etc.] on the retention times of metal ions was investigated in detail. With the combination of citric acid-PDCA as eluent all alkali and alkaline earth ions could be completely separated within 12 min. Alkali, alkaline earth and heavy metal ions [Cu/Zn/Co/Fe(II)] were separated by the combination of tartaric and oxalic acid as eluent in a single run. Trace amounts of Na, K and Ca were successfully separated from the Mg-matrix by an EDTA-PDCA eluent. For the IC with indirect UV-detection the eluent consisting of CuSO₄ or CuCl₂ was used to separate Na, K, Mg and Ca with baseline resolution within 10 min.The detection limits of metal ions with conductivity detection were found beween 0.5 g/l for Li and 8 g/l for Cs. They were 10 times more sensitive than those with indirect UV-detection.This IC-method was applied to determine alkali, alkaline earth and Mn ions in the water, food, ore-cinder and sole-brine samples with satisfactory results.Dedicated to Prof. Dr. G. Schulze on the occasion of his 60th birthday     

Separation behavior of U(VI) and Th(IV) on a cation exchange column using 2,6-pyridine dicarboxylic acid as a complexing agent and its application for the rapid separation and determination of U and Th by ion chromatography

The retention behavior of U and Th as their 2,6-pyridine dicarboxylic acid (PDCA) complexes on a cation exchange column was investigated under low pH conditions. Based on the observed retention characteristics, an ion chromatographic method for the rapid separation of uranium and thorium in isocratic elution mode using 0.08 mM PDCA and 0.24 M KNO(3) in 0.22 M HNO(3) as the eluent was developed. Both uranium and thorium were eluted as their PDCA complexes within 2 min, whereas the transition and lanthanide metal cations were eluted as an unresolved broad peak after thorium. Under the optimized conditions both U and Th have no interference either from alkali and alkaline earth elements up to a concentration ratio of 1:500 or from other elements up to 1:100. The detection limits (LOD) of U and Th were calculated as 0.04 and 0.06 ppm, respectively (S/N=3). The precision in the measurement of peak area of 0.5 ppm of both U and Th was better than 5% and a linear calibration in the concentration range of 0.25-25 ppm of U and Th was obtained. The method was successfully applied to determine U and Th in effluent water samples.     

Zwitterionic ion chromatography with carboxybetaine surfactant-coated particle packed and monolithic type columns

Both particle packed (25 cm x 0.46 cm I.D. SUPELCOSIL 5 microm C18) and monolithic type (10 cm x 0.46 cm I.D. Merck Chromolith Performance C18) reversed-phase substrates were dynamically coated with a carboxybetaine type zwitterionic surfactant ((dodecyldimethyl-amino) acetic acid) and investigated as stationary phases for use in zwitterionic ion chromatography (ZIC). Investigations into eluent concentration and pH were carried out using KCl eluents containing 0.2 mM of the carboxybetaine surfactant to stabilise the column coatings. It was found that eluent concentration decreased anion retention whilst simultaneously increasing peak efficiencies, which may be due to the dissociation of intra- and inter-molecular salts of the carboxybetaine surfactant under higher ionic strength conditions. The Effect of eluent pH was an increase in anion retention with decreased eluent pH due to the increased protonation of the weak acid terminal group of the carboxybetaine, causing both a relative increase in the positive charge of the stationary phase and less repulsion of the anions by the dissociated weak acid group. The carboxybetaine-coated monolithic phase was applied to rapid anion separations using elevated flow rates and flow rate gradients.     

Anion-exchange chromatography on short reversed-phase columns modified with amphoteric (N-dodecyl-N,N-dimethylammonio)alcanoates

Short reversed-phase columns (50 mm x 4.6 mm Gemini C(18)) were dynamically coated with carboxybetaines of the general structure, C(12)H(25)N(+)(CH(3))(2)(CH(2))(n)COOH, namely (N-dodecyl-N,N-dimethylammonio)undecanoate, DDMAU (n=10) and (N-dodecyl-N,N-dimethylammonio)butyrate, DDMAB (n=3), and investigated for the separation of inorganic anions in ion chromatography. The role of the ionic strength of coating surfactant solutions on their adsorption and resultant column capacity was studied. The retention of inorganic anions was investigated with different eluents at various concentrations and pH. Interestingly, no retention for anions was found with pure water as the eluent, but the addition of small amounts of electrolytes, up to 0.1 mM, caused a sharp increase in the retention of analytes. The effect of increasing anion retention with an increase in eluent cation charge was also observed. Based on this effect a new cation charge gradient concept was proposed and applied to the separation of a standard mixture of anions.     

单一阴离子交换柱同时分离有机酸和无机阴阳离子

研究了用乙二胺四乙酸（ＥＤＴＡ）作淋洗液时，性质迥异的有机酸、无机阴离子和碱土金属离子（Ｃａ＾２＋、Ｍｇ＾２＋）在同一阴离子交换柱上的同时分离以及保留机理，结果表明，在离子交换机理之外，非离子交换机理对有机酸及钙镁的ＥＤＴＡ络阴郭的保留行为起一定的辅助作用，９种有机酸和无机阴阳离子在１０ｍｉｎ内得到了较好的分离。各离子的电导检测灵敏度在１０＾－９至１０＾－１１ｍｏｌ，能满足环境和食吕分析的要求。     

螯合离子色谱法分析复杂基体中痕量金属离子的研究

发展了应用螯合离子色谱法分析复杂基体中痕量金属离子的新方法。针对不同的检测目的,利用螯合柱（ＭｅｔＰａｃＣＣ－１）和浓缩柱（ＴＭＣ－１）,采用适当的洗脱液在线将基体中的阴离子、一价阳离子、碱土金属离子以及其它干扰离子除去,同时,浓缩富集待测的痕量金属离子,然后再选择适当的梯度淋洗体系,在含有双功能基的分析柱上分离Ｐｂ,Ｃｕ,Ｃｄ,Ｃｏ,Ｚｎ和Ｎｉ等过渡金属离子和１４种镧系金属离子,继而用在线柱后衍生和光度法检测。方法简单快速,样品经适当的酸消解成溶液后即可进样,灵敏度高,检测限为１０－９级甚至更低。     

Determination of 2,4,6-trichloroanisole in wines by headspace solid-phase microextraction and gas chromatography-electron-capture detection

The retention behaviour of alkaline earth cations was studied as a function of changing composition of acidified ethylenediamine eluent. The multiple eluent species retention model developed for separation of calcium, magnesium and strontium ions was utilized for determination of selectivity coefficients for sample and eluent ions. The suggested model accurately describes and predicts retention of analytes under elution conditions [0.5-2.0 mM C2H4(NH2)2 and pH 4-6] which are of practical importance. The results in three-dimensional retention surface with species distribution graphs are demonstrated. Complexometric titrations and ion chromatography (IC) were compared for the analysis of calcium and magnesium ions. Statistical data indicated that there was no evidence for relative differences between the two methods. However, IC gives several advantages over volumetric method.     

Suppressed anion chromatography using mixed zwitter-ionic and carbonate eluents

Effect of mixed eluents which contain zwitterions such as 2-(N-morpholino)ethanesulfonic acid (MES), 3-(N-morpholino)propanesulfonic acid (MOPS), 2-(cyclohexylamino)ethanesulfonic acid (CHES) and 3-(cyclohexylamino)-1-propanesulfonic acid (CAPS) and carbonate for suppressed conductivity ion chromatography (IC) were studied. The retention behaviors of all species were affected with different anion exchange columns when adding some zwitterion into carbonate eluent. The retention time of all species, especially those of strong retetion, was substantially shortened in AS14A column with either Na(2)CO(3)/CHES or Na(2)CO(3)/CAPS as eluent while a general increase in retetion time was noticed in AS9-HC column. Low pH of eluent was achieved when zwitterion was added. Without much changes in the background conductivity after suppressed, CHES could be used as suppressed conductivity ion chromatography eluent for determination of species unstable in strong alkaline, such as determination of phosphate in heteropoly acid (HPA) samples in AS14 column. The mixed eluent could also affect the selectivity when it was applied to the study of simultaneous separation of anions and cations in AS9-HC column by suppressed ion chromatography.     

Separation and analysis of aluminium(III) by cation exchange ion chromatography

A method for the determination of aluminium(III) ions based on separation by cation exchange column chromatography and detection by conductivity detector has been developed. It is fast and reliable, and can be used for the separation and analysis of aluminium(III) ions from other metal ions like Mg(II), Mn(II), Zn(II), Co(II), Ca(II), Sr(II), rare earth elements like Lu(III), Tm(III), and Gd(III), which are eluted at different times and so do not interfere. Effect of p-phenylene diamine concentration present in the eluent, presence of other metal ions and effect of various anions present in the injection sample on the separation and analysis of aluminium(III) ions have also been studied.     

Rapid analysis of proteins and peptides by reversed-phase chromatography with polymeric micropellicular sorbents

Peptides and proteins were separated by reversed-phase chromatography on a 30 x 4.6 mm I.D. column packed with non-porous crosslinked polystyrene particles having a mean particle diameter of 3 micron and a rugulose surface. The polymeric support did swell slightly in organic solvents, but the estimated 5-8% change in particle diameter did not adversely affect the efficiency of the column which was used repeatedly with gradient elution from water to organic solvent under conditions typically employed in reversed-phase chromatography. In these experiments, the pH of the eluent was varied in a wide range in order to compare the effect of acidic and alkaline eluents on the separation of protein and complex peptide mixtures. The column showed no deterioration even after extensive exposure to alkaline mobile phases. The retention behavior of sixteen proteins having widely different pI values was studied as a function of the eluent pH. The chromatographic system exhibited large selectivity differences upon changing the pH of the eluent from 2 to 11. Analytical information about peptide and protein mixtures could therefore be enhanced by using eluents at the pH extremes. At the pH extremes of 2 and 11 peak sharpness and protein mass recovery were found to be superior to those obtained with neutral eluents. Usually the column temperature was held at 80 degrees C and typical analysis times ranged from 30 s to 10 min as illustrated by chromatograms of protein mixtures and by peptide maps. With regular use under such conditions the column showed no deterioration after three months.     

Ion-chromatographic behavior of alkali metal cations and ammonium ion on zirconium-adsorbing silica gel

The preparation and evaluation of zirconium-adsorbing silica gel (Zr-Silica) as an ion-exchange stationary phase in ion chromatography for inorganic anions and cations was carried out. The Zr-Silica was prepared by the reaction of silanol groups on the surface of the silica gel with zirconium butoxide (Zr(OCH2CH2CH2CH3)4) in ethanol. The ion-exchange characteristics of the Zr-Silica were evaluated using 10 mM tartaric acid at pH 2.5 as eluent. The Zr-Silica was found to act as a cation-exchanger under the eluent conditions. The retention behavior of alkali and alkaline earth metal cations was then investigated. The Zr-Silica column was proved to be suitable for the simultaneous separation of alkali metal cations and ammonium ion. Excellent separation of the cations on a 15 cm Zr-Silica column was achieved in 25 min using 10 mM tartaric acid as eluent.     

Dynamic adsorption and desorption of heavy metal ions on poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fiber

The dynamic adsorption and desorption properties, including the effect of pH value and flow rate on the adsorption, eluent acidity and volume, eluting velocity and re-use, of Cu(II), Pb(II), Zn(II), Cd(II), Mn(II), Ni(II), Co(II) and Hg(II) ions on the column loaded with poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fiber were investigated. The recovery of Mn(II), Co(II), Cd(II), Ni(II) and Zn(II) ions in the presence of Na, K, Ca and Mg ions was examined. The preconcentration of trace amounts of Mn(II), Co(II), Cd(II), Ni(II) and Zn(II) ions from model solution samples was carried out with satisfactory results. The amount of the metal ions detected after preconcentration and recovery by this technique was basically in agreement with the added amount. The method is rapid, precise and simple. Received: 15 October 1997 / Revised: 17 March 1998 / Accepted: 20 March 1998     

Dynamic adsorption and desorption of heavy metal ions on poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fiber

The dynamic adsorption and desorption properties, including the effect of pH value and flow rate on the adsorption, eluent acidity and volume, eluting velocity and re-use, of Cu(II), Pb(II), Zn(II), Cd(II), Mn(II), Ni(II), Co(II) and Hg(II) ions on the column loaded with poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fiber were investigated. The recovery of Mn(II), Co(II), Cd(II), Ni(II) and Zn(II) ions in the presence of Na, K, Ca and Mg ions was examined. The preconcentration of trace amounts of Mn(II), Co(II), Cd(II), Ni(II) and Zn(II) ions from model solution samples was carried out with satisfactory results. The amount of the metal ions detected after preconcentration and recovery by this technique was basically in agreement with the added amount. The method is rapid, precise and simple. Received: 15 October 1997 / Revised: 17 March 1998 / Accepted: 20 March 1998     

Retention model for the separation of anionic metal-EDTA complexes in ion chromatography

A retention model is derived for complex anions eluted from an anion-exchange column with multiple ionic eluents containing hydrogencarbonate, carbonate, and hydroxyl species and the sample solution, containing transition metals, anions and complexing ligand. The theory is based on the generalized ion-exchange equilibrium, protonation and complex-formation equilibria. The unknown parameters of chromatographic ion-exchange equilibrium constants for sample and eluent species are determined from the experimental retention data by iterative minimization, using a non-linear regression algorithm. The model was utilized to predict the retention behaviour of CdEDTA²⁻, CoEDTA²⁻, MnEDTA²⁻ and NiEDTA²⁻ ions. The capacity factors of complex ions were determined for wide ranges of pH values and eluent concentrations. Good agreement was obtained between the observed and predicted retentions.     

Development of column-pretreatment chelating resins for matrix elimination/multi-element determination by inductively coupled plasma-mass spectrometry

Chelating resins, two kinds of iminodiacetate derivatives (IDA) of cross-linked chitosan (CCS) were synthesized and investigated for adsorption capacity, matrix elimination and collection/concentration of analytes by a column pretreatment in a multi-element ICP-MS determination method. The adsorption behavior of 54 elements at the 10 ng ml(-1) level on chitosan derivatives in a packed mini-column was systematically examined. Almost 30 kinds of metal ions were recovered quantitatively at pH 5 with CCS-HP/IDA (cross-linked chitosan possessing N-2-hydroxypropyl iminodiacetic acid groups) column. Compared with available chitosan-iminodiacetate resin, CHITOPEARL CI-03, the recovery of the metal ions such as Cu, Pb and La is satisfactory with CCS-IDA (cross-linked chitosan possessing N,N-iminodiacetic acid groups) and CCS-HP/IDA using 2 M nitric acid as an eluent, which may be attributed to the difference of cross-linking and macroporous structure. Compared with Chelex-100, the adsorption efficiency is in the order: Chelex-100 > CCS-IDA > CCS-HP/IDA, especially in the chelating ability for alkaline earth metals. The resin with a longer spacer (CCS-HP/IDA) showed higher adsorption selectivity between heavy metal ions and alkaline earth metals at pH < 7. The separation efficiency of the major matrix cations in seawater (Na. K, Mg, Ca) has also been investigated, and matrix interference was negligible even in a seawater sample at pH 5 with CCS-HP/IDA. The recoveries of Mn at pH 5 with CCS-HP/IDA or Chelex-100 were almost 100%. However, those of Mg with each resin were 4 or 98%, respectively. The adsorption capacities of synthesized CCS-HP/IDA for Cu(II), Pb(II) and La(III) were 0.90, 0.65 and 0.34 mmol g(-1), respectively. Therefore, the chelating chitosan resins developed are applicable to the pretreatment of trace amounts of elements in various kinds of water samples.