阴/阳离子表面活性剂复配体系的中相微乳液研究

阴离子表面活性剂双-2-乙基己基磺化琥珀酸钠(简称AOT), 和阳离子表面活性剂十六烷基三甲基溴代铵(简称CTAB), 在有醇、正辛烷、盐水存在的情况下,能形成多相微乳液。本文系统地研究了阴/阳离子表面活性剂配比、醇的种类、醇的浓度对该体系的中相微乳液的形成及特性的影响, 得到了中相微乳液的特性参数(最佳含盐量S^*, 最佳中相微乳液体积V^*, 界面张力r~E、盐宽△S等)。这些性质对与阴/阳离子表面活性剂复配体系, 三次采油及日用化工上的应用开发具有重要意义。最后还开展单独阴离子表面活性剂体系和阴/阳离子表面活性剂复配体系进行了比较, 得到一些有价值规律, 并从理论上进行了探讨。     

Phase Behavior of Microemulsions Formulated with Sodium Alkyl Polypropylene Oxide Sulfate and a Cationic Hydrotrope

The partial ternary phase diagram of anionic extended surfactant of alkyl polypropylene oxide sulfate C₁₂(PO)₄SO₄ alone and combined with the cationic hydrotrope, tetrabutyl ammonium bromide with water and decane were determined under ambient conditions. Middle phase microemulsion was formulated using salinity scans in the dilute region of surfactant/brine/decane. Visual inspection as well as cross polarizer and optical microscopy were used to detect anisotropy. Spinning drop tensiometer was used to measure interfacial tension (IFT). The first ternary phase diagram using the extended surfactant alone showed three one phase regions, the anisotropic lamellar liquid crystalline phase, L _α and the isotropic L₁ micellar liquid and L₃ sponge phase. In the second ternary phase diagram using the extended surfactant combined with tetra butyl ammonium bromide, an isotropic micellar region, L ₁, appeared in the diluted area of the phase diagram. Meanwhile the L _α phase disappeared completely and the three phase region has a bluish transparent middle phase. Interfacial tension measurements between middle phase and brine, and between decane and brine yielded ultra low values. Calculated IFT values using the characteristic length obtained using De Gennes approximation gave almost half the measured values. The interfacial rigidity was also calculated and compared to values obtained from the literature.     

THE RELATIONSHIP BETWEEN THE MOLAR PARTITION COEFFICIENT AND THE ULTRALOW INTERFACIAL TENSION MINIMUM IN A PETROLEUM SULFONATE/ HYDROCARBON/BRINE SYSTEM

The partitioning of a sodium petroleum sulfonate between heptane and brine yields surfactants with different molar absorptivity and λ_max values in the two phases, except near the point of minimum interfacial tension, e of the surfactant in the heptane phase increases sharply above the point of minimum interfacial tension between the two phases. The molar partition coefficient, M_H/M_W, for the surfactant between the heptane and brine phases is unity at surfactant concentrations in the brine phase below the point of minimum interfacial tension and drops sharply at concentrations above it. The critical micelle concentration of the surfactant in the aqueous phase equilibrated with the heptane phase is considerably below the concentration for minimum interfacial tension     

Phase Diagrams and Solubilization of Chlorocarbons in Chlorocarbon/Water/Anionic Surfactant/Alcohol Microemulsion Systems

The solubilization abilities of various chlorocarbons were investigated in a middle phase microemulsion system anionic surfactant sodium dodecyl sulfate (SDS) or sodium dodecyl sulfonate (AS)/n-butanol/chlorocarbon/brine with a ε-β fishlike phase diagram. The composition of the balanced interfacial layer of the microemulsion and some other parameters are calculated. The result shows that surfactant little dissolves in water and chlorocarbon phases, while alcohol mainly dissolves in water and oil phases besides in the interfacial layer. The order of the solubilization ability is dichloromethane (CH₂Cl₂) ～ carbon tetrachloride (CCl₄) > tetrachloroethylene (PCE) > o-dichloro-benzene. The solubility of the alcohol decreases with the increase in NaCl concentrations, which should be compensated by the increase in the amount of alcohol as cosolvent (Cs), so as to maintain the balanced interfacial layer. Salinity has little effect on the partition of surfactant between phases.     

Formulating Middle Phase Microemulsions Using Extended Anionic Surfactant Combined with Cationic Hydrotrope

The phase behavior of systems containing sodium alkyl polypropylene oxide sulfate with equimolar ratio of polypropylene oxide ammonium chloride was determined as a function of salt concentration and alkane carbon number at ambient temperature. Visual inspection as well as cross polarizers were used to detect anisotropy. Solubilization ratios for oil and brine in the middle phases were measured and used to calculate the interfacial tension (IFT) between the microemulsion and oil or brine. The fish diagram is presented showing a minimum amount of 0.20 wt% surfactant needed to form the middle phase. Swelling increases with decreasing the alkane carbon number of the oil. Ultra low IFT values were predicted for the systems investigated.     

Conductometric study of the mixing behaviour of sodium benzoate and salicylate with an anionic surfactant sodium lauroylsarcosinate

Effects of two anionic hydrotropes – sodium benzoate (NaBz) and sodium salicylate (NaSal) – on the mixed-micelle formation with an amino-acid-based surfactant – sodium lauroylsarcosinate (SLS) – in water were investigated by the conductometric method. Specific conductivity was measured for SLS/NaBz/water and SLS/NaSal/water systems to determine the critical micelle concentration (cmc). Using the regular solution theory for non-ideal mixing, the pairwise interaction parameter, β₁₂, and micellar composition, χ, were estimated in the mixed micelle. The cmc values of the surfactant–hydrotropes mixtures were generally lower than those predicted from the ideal mixing theory. The β₁₂ values are generally negative for the two systems at all mole fractions with an average value of ?2.83 for the SLS/NaBz and ?3.31 for SLS/NaSal systems, respectively, indicative of a strong attractive interaction between the SLS/NaBz and SLS/NaSal mixed micelle. The calculated thermodynamic parameters of micellisation all indicated spontaneity in mixed-micelle formation for the systems studied.     

Self-assembly in linker-modified microemulsions

Linker molecules are added to microemulsion systems to enhance the interaction between the surfactant and oil (lipophilic linkers) or water (hydrophilic linkers) phases. Previous results suggest that when lipophilic and hydrophilic linkers are combined they behave as a self-assembled surfactant at the oil/water interface. In this work we investigate this self-assembly phenomenon as a function of surfactant, linker and electrolyte concentration. We find that middle phase microemulsion appears at a specific concentration higher than the critical micelle concentration (CMC), which we denote as the critical middle phase microemulsion concentration (CmicroC). When the lipophilic linker dodecanol is added in equimolar ratio to the hydrophilic linker sodium mono- and dimethyl naphthalene sulfonate (SMDNS), the middle phase microemulsion did not appear until the surfactant sodium dihexyl sulfosuccinate (SDHS) concentration was larger than the CmicroC of the SDHS-alone system. Dodecanol is shown to segregate near the surfactant tails following a Langmuir-type adsorption process. This segregation is not affected by the electrolyte concentration but is significantly reduced when the surfactant (SDHS) concentration approaches the CmicroC. The data suggest that the self-assembly between hydrophilic and lipophilic linkers to form middle phase microemulsions is only possible if a minimum amount of surfactant is present.     

Phase behaviour and physicochemical properties of microemulsions with a non-ionic surfactant (IGEPAL)

The non-ionic surfactant pentaethylenglycol-4-octylphenyl ether (igepal CA-520) represents a good industrial alternative to the long-tail members of the C_iE_j family. In this paper, the phase behaviour of the microemulsion system igepal CA-520/n-decane/brine is studied in detail. An isotropic phase was found, as well as liquid crystalline and cream-like structures, depending on composition and temperature. Such structures can either form single-phase homogeneous mixtures, or coexist with other structures when phase separation takes place. Below surfactant concentration of about 20%, more complicated phase equilibria develop as temperature changes. The presence of different additives shifts the temperature ranges where the different phases exist, while keeping the general shape of the phase diagram, which agrees with the general rules for non-ionic surfactants. Complementary rheology experiments reveal a change from non-Newtonian to Newtonian behaviour during the phase transition from a lamellar phase to the isotropic microemulsion. A structure of water droplets associated in clusters can be proposed from SANS and electrical conductivity.     

Formation of Cubic-Phase Microemulsions with Anionic and Cationic Surfactants at Equal Amounts of Oil and Water

The formation and microstructure of cubic phases were investigated in anionic and cationic surfactant-containing systems at 25 degrees C. In the system sodium dodecyl sulfate(SDS)-dodecyltrimethylammonium bromide(DTAB)-water, mixing of two surfactants shows the phase transition hexagonal phase (H(1))-->surfactant precipitate, accompanied by an obvious decrease in the cross-sectional area per surfactant in the rod micelles of the hexagonal liquid crystal. In the mixed systems brine(A)-dodecane(B)-SDS(C)-DTAB(D)-hexanol(E), the isotropic discontinuous cubic phase is formed from the H(1) phase at a low cationic surfactant weight fraction, Y=D/(C+D), and from the lamellar phase at high Y upon dilution with equal amounts of oil and brine, respectively. The minimum surfactant concentration to form the cubic phase decreases with increases both in cationic surfactant weight fraction Y from 0 to 0.30 and in hexanol weight fraction, W(1)=E/(C+D+E), accordingly. The maximum solubilization for oil of the cubic phase reaches 43 wt% at 14 wt% of mixed surfactants and alcohol. Copyright 2000 Academic Press.     

The Self-Association and Mixed Micellization of an Anionic Surfactant,Sodium Dodecyl Sulfate,and a Cationic Surfactant,Cetyltrimethylammonium Bromide: Conductometric,Dye Solubilization,and Surface Tension Studies

In the present study, we investigate the self-association and mixed micellization of an anionic surfactant, sodium dodecyl sulfate (SDS), and a cationic surfactant, cetyltrimethylammonium bromide (CTAB). The critical micelle concentration (CMC) of SDS, CTAB, and mixed (SDS + CTAB) surfactants was measured by electrical conductivity, dye solubilization, and surface tension measurements. The surface properties (viz., C₂₀ (the surfactant concentration required to reduce the surface tension by 20 mN/m), Π_CMC (the surface pressure at the CMC), Γ_max (maximum surface excess concentration at the air/water interface), and A_min (the minimum area per surfactant molecule at the air/water interface)) of SDS, CTAB, and (SDS + CTAB) micellar/mixed micellar systems were evaluated. The thermodynamic parameters of the micellar (SDS and CTAB), and mixed micellar (SDS + CTAB) systems were evaluated.

A schematic representation of micelles and mixed micelles.     

Electroosmotic Flow of a General Electrolyte Solution through a Fibrous Medium

Although hydrotropy is extensively used in industry, the molecular mechanism of hydrotropic solubilization has not been completely elucidated yet. In this paper the interaction between a nonionic surfactant (ethoxylated fatty alcohol containing between five and six oxyethylenic units) and sodium p-toluene sulfonate is examined. Surface tension measurements confirm that the hydrotropic effect occurs at a concentration in which the hydrotropes self-associate. Photon correlation spectroscopy studies show that for this concentration of hydrotropes a drastic reduction in the surfactant micellar radius occurs. Furthermore the luminescence of the hydrotrope used as a fluorescence probe indicates that at low concentrations p-toluene sulfonate dissolves in the surfactant micelles but beyond the minimum concentration for hydrotropic solubilization the hydrotrope is present in the aqueous phase. These results suggest that the hydrotropic effect is related to alterations in the water structure induced by the hydrotrope molecules and to the presence of hydrotrope aggregates that furnish an appropriate niche for the surfactant amphiphile.     

Studies on the phase behavior and solubilization of the microemulsion formed by surfactant-like ionic liquids with ɛ–β-fish-like phase diagram

The phase behavior and the solubilization of the microemulsion systems surfactant-like ionic liquids 1-hexadecyl-3-methylimidazolium bromide (C₁₆mimBr), 1-tetradecyl-3-methylimidazolium bromide (C₁₄mimBr), or 1-dodecyl-3-methylimidazolium bromide (C₁₂mimBr)/alcohol/alkane/brine have been studied with ɛ–β-fish-like phase diagram method at 40 °C and an oil-to-water mass ratio of 1:1. From the ɛ–β-fish-like phase diagram, the physicochemical parameters, such as the mass fraction of alcohol in the hydrophile–lipophile-balanced interfacial layer (A ^S), and the solubilities of ionic liquid (S ^O) and alcohol (A ^O) in alkane phase, were calculated. The solubilization of the microemulsion system has been discussed based on the ɛ–β-fish-like phase diagram. The smaller the oil molecule, the longer the alcohol chain length, and the larger the NaCl concentration in water, the larger the solubilization of the microemulsion system. In this paper, the solubilization of the microemulsion stabilized by both C₁₂mimBr and sodium dodecyl sulfonate (sodium dodecyl sulfate) was also investigated with the ɛ–β-fish-like phase diagram. The unequimolar composite of anionic and cationic surfactants can avoid the sedimentation aroused by the strong electrostatic attraction, and an obvious synergism effect in solubilization was obtained.     

Salt Effects on Aqueous Cationic/Anionic Surfactant Two‐Phase Regions

The influence of added salts (KCl, NaF, NaCl, NaBr, Na₂SO₄, Na₃PO₄) on aqueous cetyltrimethylammonium bromide (CTAB)/sodium dodecyl sulfonate (AS) two‐phase regions were studied. For KCl, the concentration dependence of salt effect on aqueous two‐phase regions was investigated. When brine substitutes pure water as a solvent, the positions of aqueous two‐phase regions in the phase diagram change. The results indicate that for aqueous two‐phase systems with excess anionic surfactant (ATPS‐A), the salt effect was mainly dependent on the cationic inorganic counterions, whereas for aqueous two‐phase systems with excess cationic surfactant (ATPS‐C), the salt effect was mainly dependent on the anionic inorganic counterions. The shift of aqueous two‐phase region is strengthened following the Hofmeister series. All the experiments were performed at 318.15 K.     

Polymerisation of styrene in microemulsion with catanionic surfactant mixtures

The use of aqueous catanionic surfactant mixtures in the oil-in-water (o/w) microemulsion polymerisation of styrene is reported. Catanionic surfactant mixtures of dodecyltrimethylammonium bromide 1 and sodium dodecylsulfate 3, or decanediyl-1,10-bis(dimethyldodecylammonium bromide) 2, a gemini surfactant, and the anionic surfactant 3 were used. Phase behaviour and polymerisation properties of the microemulsions were studied as a function of the total surfactant concentration and the cationic/anionic surfactant ratio. Single-phase o/w microemulsions were only formed if either the cationic or anionic surfactant were present in large excess. Upon -irradiation, polymer nanoparticles were obtained. Using dynamic light scattering, the particle radii were determined to be 10 to 20 nm, the size depending on the total surfactant concentration, the cationic/anionic surfactant ratio and the surfactant/styrene ratio. Size exclusion chromatography indicated molecular weights of polystyrene of between 3×10⁵ and 1.4×10⁶ Daltons. Catanionic 1/3 and 2/3 mixtures differ in their styrene solubilizations. In a 1- or 3-rich system, the solubilization efficiency can be improved by increasing the concentration of the oppositely charged minor surfactant component, while in a 2-rich system the addition of 3 only diminishes the efficiency. Possible reasons for the different behaviours are discussed.     

Extraction of cobalt by the AOT microemulsion system

The extraction of cobalt by Winsor II microemulsion system was studied. In the bis (2-ethylhexyl) sulfosuccinate sodium salt (AOT)/n-pentanol/n-heptane/NaCl system, AOT was used as a anionic surfactant to form microemulsion in n-heptane, n-pentanol was injected in the microemulsion as a cosurfactant. Co(II) was found to be extracted into the microemulsion phase due to ion pair formation such as Co²⁺(R–SO₃ ⁻)Cl. The influence of different parameters such as the volume ratio of aqueous phase to microemulsion, surfactant concentration, pH of the feed solutions, cosurfactant concentration as well as temperature on the extraction yield (E%) were investigated. The results showed that it was possible to extract 95% of cobalt by the AOT Winsor II microemulsion.     

Synthesis and performance of a series of dual hydroxyl sulfobetaine surfactants

Five kinds of dual hydroxyl sulfobetaines with different carbon atom numbers in hydrophobic chain were synthesized by using linear saturated alcohol, epichlorohydrin and dimethylamine, and then their structures were characterized by FTIR and ¹H NMR. The stability of all synthesized betaine surfactants in hard water was at level 4, which indicated they had high tolerance on hard water. Their CMC and γ_cmc were lower than the conventional cationic surfactant dodecyltrimethylammonium bromide and anionic surfactant sodium dodecyl, so they had more excellent surface activities. With the chain length increasing from C₈ to C₁₄, the surface activities, emulsifying properties and foaming properties of these betaine surfactants improved because surfactant molecules tightly arranged in the oil-water interface, but there was abnormal phenomenon of surface activity and foam property from C₁₄ to C₁₆ due to overlong hydrophobic chain. According to the results of the experiment, C₁₄SB was the most practical in the five kinds of surfactants, which was potential candidate to enhance oil recovery in oil field. The performances of C₁₄SB were as follows: CMC?=?2.2?×?10^?4?mol/L, γ_cmc?=?30.9 mN/m and the time of bleeding 10?mL water t?=?375?s at 2?g/L the optimum emulsification concentration.     

改性二氧化硅纳米颗粒提高二氧化碳泡沫稳定性的研究

通过纳米二氧化硅的硅烷化改性, 使其在高矿化度盐水中可以稳定存在的前提下, 研究了改性纳米颗粒与阳离子表面活性剂十二烷基三甲基氯化铵混合体系的溶液稳定性及协同稳定CO₂泡沫的效果. 研究结果表明, 无机盐离子对改性纳米颗粒与阳离子表面活性剂间的静电吸引力具有屏蔽作用, 且矿化度越高, 屏蔽效果越明显, 从而混合溶液更易于在高盐水中稳定; 纳米颗粒表面的活性剂吸附层受二者浓度的影响, 进而影响了颗粒的亲/疏水性; 当混合体系中的表面活性剂浓度低于临界胶束浓度(CMC)时, 混合溶液与CO₂的界面张力高于单独活性剂溶液, 而当活性剂浓度高于CMC时, 对CO₂-溶液界面张力几乎无影响, 最低界面张力可降至6 mN/m左右; 改性纳米颗粒的加入可以进一步提高CO₂体相泡沫半衰期一倍以上, 但受二者浓度比例的影响; 纳米颗粒的加入有效提高了多孔介质中泡沫的表观黏度, 最大增幅由20 mPa·s增至55 mPa·s左右, 泡沫黏度增加接近3倍, 增强了CO₂泡沫驱的封堵作用.     

Micellization and mixed micellization of cationic gemini (dimeric) surfactants and cationic conventional (monomeric) surfactants: Conductometric,dye solubilization,and surface tension studies

In the present study, we have investigated the self-association, mixed micellization, and thermodynamic studies of a cationic gemini (dimeric) surfactant, hexanediyl-1,6-bis(dimethylcetylammonium bromide (16-6-16)) and a cationic conventional (monomeric) surfactant, cetyltrimethylammonium bromide (CTAB). The critical micelle concentration (CMC) of pure (16-6-16 and CTAB) and mixed (16-6-16+CTAB) surfactants was measured by electrical conductivity, dye solubilization, and surface tension measurements. The surface properties (viz., C₂₀ (the surfactant concentration required to reduce the surface tension by 20 mN/m), Π_CMC (the surface pressure at the CMC), Γ_max (maximum surface excess concentration at the air/water interface), A_min (the minimum area per surfactant molecule at the air/water interface), etc.) of micellar (16-6-16 or CTAB) and mixed micellar (16-6-16+CTAB) surfactant systems were evaluated. The thermodynamic parameters of the micellar (16-6-16 and CTAB) and mixed micellar (16-6-16+CTAB) surfactant systems were also evaluated.     

Swelling of Lamellar Gel from Catanionic Hydro- and Perfluoro-Carbon Surfactant Mixtures by Refractive-Index Matching

Bilayer swelling behavior of cationic and anionic surfactant mixtures in solution induced by adding glycerin was investigated. The measurements were performed a system, cationic tetradecyltrimetylammonium bromide (TTABr), and anionic sodium perfluorodecanoate (C₉F₁₉CO₂Na) surfactant mixtures with their stoichiometric mole ratio being exactly 1 in aqueous solution. The non-precipitated phase of cationic and anionic hydro- and perfluoro-carbon surfactant mixtures being the mole ratio of 1:1 could be identified to be lamellar gel phase, which was characterized by freeze-fracture transmission electron microscopy (FF-TEM) and x-ray diffraction (XRD) measurements. Deuterium nuclear magnetic resonance (²H NMR) and rheology were used to characterize the phase transition from the lamellar gel to smaller vesicles. Phase transition from lamellar gel to smaller vesicles can be induced by adding glycerin to replace water. The addition of glycerin lowers the turbidity of the dispersion and swells the interlamellar distance between bilayers, which could be explained by matching of refractive index between solvent and bilayers.     

Effects of salinity on the viscosity and birefringence of a microemulsion system

Oil/water/surfactant systems form complex equilibrium phases which are sensitive to a number of parameters, including amount and concentration of cosurfactant (often an alcohol), salinity, and temperature. If one of these variables is changed systematically as, for example, the salinity, an interesting transition may be observed in which at low salinities a microemulsion is in equilibrium with an excess oil phase, at moderate salinities a middle phase microemulsion is in equilibrium with both excess oil and excess water phases, and at higher salinities brine is in equilibrium with a microemulsion phase. To help elucidate the structure of the microemulsion, studies of viscoelasticity and streaming birefringence in oscillatory shear flow have been conducted of a middle phase-forming system as a function of salinity. It is found that the viscoelastic properties of the microemulsions are unchanged for shear rates varying from 0.1 to 100 sec⁻¹. Both the birefringence and the viscosity maximize near the salinity marking the transition from lower phase to middle phase microemulsion. Further inflections in these properties occur at a salinity marking the midrange of the middle phase microemulsion. For all cases the dominent relaxation time is near 3 to 5 msec while the birefringence changes by two orders of magnitude. The birefringence is a sensitive indicator of the elastic structure of the microemulsion.