高压静电法制备多孔磁性壳聚糖微球

以壳聚糖(Chitosan, CS)为基质, 通过共混法引入四氧化三铁磁性颗粒, 以硅胶(Silicagel, S)为致孔剂, 在热的NaOH溶液中溶出硅胶致孔, 采用高压静电法制备磁性壳聚糖微球. 通过SEM观察了微球的结构和形貌, 并对微球结构和形貌的影响因素及其制备工艺进行了系统的研究, 结果表明, 高压静电法制备的磁性硅胶/壳聚糖微球粒径可通过微量进样器的针头大小来控制, 并且粒径分布均匀, 实验重复性及可控性好; 当以质量体积分数为5%的壳聚糖醋酸溶液(体积分数2％, mS∶mCS=4∶1), 用8号针头进样时, 制得直径约为600 μm, 孔洞分布均匀, 孔径约为50 μm的多孔磁性壳聚糖微球. 由于磁性多孔壳聚糖微球中含有大量的活性羟基和氨基, 因此显弱碱性, 对酸性物质和金属离子的吸附作用很好, 且可通过外加磁场进行有效分离. 磁性多孔壳聚糖微球在生物分离及污水中的酸性染料处理方面具有潜在的应用价值.     

磁性壳聚糖-聚丙烯酸微球的制备及表征

壳聚糖通过与丙烯酸接枝共聚制得壳聚糖聚丙烯酸悬浮液,在铁磁流体(Fe3O4)与聚乙二醇(分散剂)存在下通过与戊二醛交联,制备了磁性壳聚糖聚丙烯酸微球。用扫描电镜、红外光谱对合成的高分子微球进行形貌观察和结构表征,并进行了元素分析和磁性能测试,研究了磁性微球对牛血清白蛋白(BSA)的吸附效果。结果表明,合成的磁性微球外表呈球形,粒径为100～400nm;当Fe含量为2.47%时,磁性微球的饱和磁化强度约为1.30emug,磁矫顽力为280Oe,磁化率为2.16×10-4(常温下),属于顺磁性材料;其对BSA有较好的吸附效果,饱和吸附量约为400mgg。     

磁性壳聚糖微球的制备及对Cr(Ⅵ)的吸附性能研究

用壳聚糖包埋磁流体,用戊二醛交联制成磁性壳聚糖微球,并用红外光谱表征其结构。用制备的磁性壳聚糖微球吸附Cr(Ⅵ)离子,考察了其对Cr(Ⅵ)离子的吸附性能;探讨了吸附时间、溶液pH值、吸附剂用量、温度、Cr(Ⅵ)起始浓度以及其他离子存在对Cr(Ⅵ)离子去除率的影响。实验结果表明,磁性壳聚糖微球吸附Cr(Ⅵ)离子的最佳条件为:吸附平衡时间40 min,最佳吸附pH值6左右,磁性壳聚糖微球用量10 mg,温度升高有利于提高磁性壳聚糖微球的吸附效率,Cr(Ⅵ)离子起始质量浓度为12μg/mL,无机盐的存在引起磁性壳聚糖微球的吸附性能降低。并且考察了吸附剂的再生性能,实验结果表明磁性壳聚糖微球具有良好的重复使用性。     

磁性壳聚糖微球的制备和应用

磁性壳聚糖微球是通过一定的方法用壳聚糖将磁性材料包埋而形成的磁性微球,其内核为纳米级的磁性金属微粒,外层为壳聚糖.壳聚糖含有大量的氨基和羟基,使其具有特定的理化性质,由此奠定了壳聚糖的许多生物学特性及加工特性的基础.另一方面,其磁性内核使磁性壳聚糖微球具有很好的顺磁性,利用外加磁场可以很方便地进行分离.因此磁性壳聚糖在固定化酶、污水处理、食品工业和生物医药等方面具有广泛的用途,磁性壳聚糖的制备及应用的相关研究也越来越受到重视.本文作者对磁性壳聚糖微球的制备和应用进行评述.     

磁性壳聚糖硅胶复合微球的制备及其吸附Cu~(2+)的性能研究

以壳聚糖与正硅酸四乙酯为原料,采用溶胶-凝胶法,用戊二醛辅助交联合成了磁性壳聚糖硅胶复合微球。通过红外光谱、扫描电镜、X-射线衍射等方法对磁性壳聚糖硅胶复合微球的形态和组成特性进行分析,制备的磁性复合微球中壳聚糖与硅胶材料复合均匀,材料粒径均一,机械强度较高。考察了制备的磁性壳聚糖硅胶复合微球对Cu~(2+)的吸附性能,结果表明微球对Cu~(2+)具有较好的吸附性能,吸附容量达到98.7mg/g。     

磁性聚苯胺纳米微球的合成与表征

报道了具有核壳结构的Fe3O4-聚苯胺磁性纳米微球的合成方法和表征结果.微球同时具有导电性和磁性能.在优化的实验条件下,可得到饱和磁化强度Ms为55.4 emu/g,矫顽力Hc为62 Oe的磁性微球.微球的导电性随着微球中Fe含量的增加而下降.微球的磁性能则随着Fe含量的增加而增大.Fe3O4磁流体的粒径和磁性聚苯胺微球的粒径均在纳米量级.纳米Fe3O4粒子能够提高复合物的热性能.实验表明,磁流体和聚苯胺之间可能存在着一定的相互作用,但这种相互作用较为复杂,难于研究     

磁性氟尿嘧啶壳聚糖微球的制备及其释药性能

磁性氟尿嘧啶壳聚糖微球的制备及其释药性能;氟尿嘧啶;壳聚糖;磁性微球;缓释     

分散聚合法合成磁性高分子微球

在磁流体存在下,以聚乙二醇(w=4000)为分散剂,乙醇/水为分散介质,进行苯乙烯—丙烯酸—二乙烯基苯的分散聚合,合成具有磁核的聚苯乙烯微球。磁性聚苯乙烯微球的红外光谱显示出磁性氧化铁的特征吸收峰(580cm~(-1)),微球内部磁性氧化铁含量可控制,500-4000μg/g之间。考察了磁流体、聚乙二醇、分散介质和丙烯酸对微球磁响应性和粒径的影响。合成了粒径为1-10μm的磁性高分子微球。     

分散聚合制备聚苯乙烯/聚氧乙烯两亲磁性高分子微球

采用分散聚合法，以乙醇／水为介质，在Fe3O4磁流体存在下，通过苯乙烯与聚氧乙烯大分子单体共聚制备休磁性高分子微球。 研究了聚合条件对微球粒径的影响。通过改变聚合条件，可以得到平均粒径为5μm-100μm的两亲磁性高分子微球。     

单分散亚微米级磁性微球的合成

以磁性氧化铁胶体粒子为种子粒子，采用吸附－溶胀法，进行苯乙烯－丙烯酸－二乙烯基苯的乳液聚合，制备亚微米级磁性高分了微球。研究了分散介质、丙烯酸、种子粒子、苯乙烯和ＰＨ调节剂等因素对聚合行为和磁性微球的影响，成功地合成了平均粒径为０．１３和０．２７μｍ、单分散性很好的磁性微球。     

Methodology for determination of magnetic force of polymeric nanocomposites

Magnetic nanocomposites present several interesting uses. They are very useful in environmental recovery, drug delivery and sensor applications. However, sophisticated magnetic measurements are very complex and present high costs, which may sometimes prevent research on these materials. Therefore, this paper presents a magnetic force test, which can be performed at relatively low cost and produces interesting results, which are very useful to support the development of these magnetic materials. Specifically, polylactic acid (PLA)/maghemite nanocomposites were prepared and characterized using Fourier transform infrared (FTIR) spectroscopy, wide-angle X-ray scattering (WAXS), small-angle X-ray scattering (SAXS) and size-exclusion chromatography (SEC). Our results demonstrate that nanocomposites, were obtained, which were also subjected to the magnetic force and magnetic susceptibility tests. The results of these latter tests were found to be linearly related, which proves the utility of the magnetic force test as a practical characterization technique.     

Review: A gentle introduction to magnetism: units,fields, theory,and experiment

We present an introduction to the workings, units of measure, and general properties of magnetic materials. This is intended as a “primer to interpretation of magnetic data” for those who are entering the field, or those who are encountering magnetic measurements in the literature. We expect this work will serve as an initial guide to the reader to familiarize them with the basics in the hope that those working in the field of magnetochemistry will wish to explore additional, more detailed literature as their specific investigations demand. Topics covered include: magnetic fields and units (SI and cgs), paramagnetism (magnetization and magnetic susceptibility), Curie and Curie–Weiss behavior, magnetic exchange interactions, magnetic anisotropy, dimeric systems and exchange-coupled networks (including chains, ladders, and layers), and long-range order.     

Chemical analysis of size-tailored magnetic colloids using slurry nebulization in ICP-OES

In this work, inductively coupled plasma emission spectroscopy was utilized to directly determine the chemical composition of magnetic fluids constituted of size-sorted ferrite nanoparticles in aqueous solution. Nickel and cobalt nanoferrites were chemically synthesized following a bottom-up route and dispersed under various pH conditions. Size and structural characteristics of nanograins were investigated by X-ray diffraction using a synchrotron source. Chemical analysis was then carried out by directly introducing diluted magnetic fluid samples (slurries) into the spectrometer. To achieve reliable measurements, sample conditions and apparatus parameters were carefully investigated. Slurry stability must be optimized in order to obtain reproducible and accurate analysis. The instrument must also be calibrated to minimize the difference between the signal produced by slurries and that of aqueous ordinary solutions. Furthermore, slurry sample introduction offers many advantages over conventional sample digestion, including reduced sample pretreatment time, less possibility of contamination and the use of direct calibration with aqueous solutions.     

Different methods for the fractionation of magnetic fluids

 Magnetic fluids are used in many fields of application, such as material separation and biomedicine. Magnetic fluids consist of magnetic nanoparticles, which commonly display a broad distribution of magnetic and nonmagnetic parameters. Therefore, upon application only a small number of particles contribute to the desired magnetic effect. In order to optimize magnetic fluids for applications preference is given to methods that separate magnetic nanoparticles according to their magnetic properties. Hence, a magnetic method was developed for the fractionation of magnetic fluids. Familiar size-exclusion chromatography of two different magnetic fluids was carried out for comparison. The fractions obtained and the original samples were also magnetically characterized by magnetic resonance and magnetorelaxometry, two biomedical applications. The size-exclusion fractions are similar to those of magnetic fractionation, despite the different separation mechanisms. In this respect, magnetic fractionation has several advantages in practical use over size-exclusion chromatography: the magnetic method is faster and has a higher capacity. The fractions obtained by both methods show distinctly different magnetic properties compared to the original samples and are therefore especially suited for applications such as magnetorelaxometry. Received: 12 July 1999/Accepted in revised form: 9 November 1999     

Magnetic Field and Magnetic Isotope Effects upon Reactions of Heavy Atom-Centered Radicals

We present our recent studies on magnetic field effects (MFEs) observed in reactions of heavy atom-centered radicals such as Si-,P-, Ge-, and Sn-radicals with a ns-laser photolysis technique under magnetic fields of 0–10 T. Although the MFES of heavy atom-centered radicals are much smaller than those of C-radicals due to the spin-orbit interaction of heavy atoms, we have found appreciable MFEs in many reactions of such heavy atom-centered radicals. Comparing the MFES of C-radicals with those of heavy atom-centered ones, we have explained the MFEs of heavy atom-centered radicals in terms of the Δg and relaxation mechanisms. We have found that the separation between the MFES due to the Δg mechanism and those due to the relaxation one is possible with the enhancement of spin relaxation by the addition of a paramagnetic ion. We have also tried to enrich magnetic isotopes of heavy atoms with the magnetic isotope effect (MIE), using the reactions which show fairly large MFES. Recently, we have succeeded in enriching ⁷³Ge. This is the heaviest isotope which has so far been enriched with the MIE from samples of natural abundance.     

磁性珠状纤维素制备工艺研究

本文较系统地研究了在采用反相悬浮包埋技术制备磁性珠状纤维素的过程中，纤维素的分子量、分散介质的性质、搅拌速度和O／W值等诸因素对磁性纤维素珠体的粒径、粒径分布和磁性材料包封率的影响。得到平均粒径在300微米以下，粒径分布指数小于1．4的磁性珠状纤维素，收率可达90％以上，且磁性材料（γ－Fe2O3）包封率较高。     

Mn0.6 Zn0.4 Fe2 O4 磁性亚微球的可控合成及磁性能

采用溶剂热法制备了单分散Mn0.6Zn0.4Fe2O4磁性亚微米球, 研究了反应工艺参数对磁性亚微米球结构形貌、 直径和静磁性能的影响规律. 研究发现, 随着反应时间的延长, 体系中的金属离子首先水解沉淀, 形成羟基氧化铁及Mn, Zn氢氧化物, 然后脱水转化为Mn0.6Zn0.4Fe2O4球形纳米粒子, 这些纳米粒子发生团聚, 形成结构疏松、 大小不均匀的亚微米粒子, 最后通过Ostwald熟化过程, 形成致密的单分散亚微米球. 降低反应溶液的pH值、 增加乙二醇或聚乙二醇的用量, 均会使亚微球的直径增大, 并可在150~500 nm范围内调控微球的粒径; 但组成磁性亚微球的纳米粒子的粒径逐渐减小, 产物的饱和磁化强度增大, 矫顽力和剩磁减小.     

磁性珠状纤维素的性能表征

本文采用反相悬浮包埋技术制各了磁性珠状纤维素（magneticcellulosebead缩写MCB），并对MCB各方面的性能进行了全面的评价：湿态孔度高达80％以上，磁化率在10-3emu／g数量级，磁性铁分布均匀，且磁稳定性较高。     

Advances in Molecular Diamagnetism

At the present state of instrumentation and quantum-mechanical approximations, diamagnetic measurements can supply information on chemical structure which complements the result of other approaches, such as infrared and NMR spectroscopy. General applicability and relatively low cost of equipment are among the advantages of this technique. There is growing interest in the relation to chemical shifts in NMR spectra and in the possibility offered by this technique for testing quantum-chemical approximations.     

Review: Preparation and Application of Magnetic Chitosan Derivatives in Separation Processes

Chitosan is one of the most abundant natural polysaccharide in nature. Due to its unique properties, chitosan has fascinated the scientific community since its discovery. When modified with other materials and combined with magnetic particles, the resulting composite material, a magnetic chitosan derivative, is provided with three significant characteristics. First, chitosan has excellent properties for preconcentration/extraction, such as adsorption and chelating effects, low cost, and nontoxicity. Second, new functional groups have enhanced the properties of chitosan that include water solubility, stability, recyclability, and enhanced adsorption capacity. Finally, due to the efficient and fast adsorption processes, as well as simple and convenient magnetic separation, the magnetic adsorbents greatly reduce the time of sample handling. In this article, recent synthesis and modification methods of magnetic chitosan derivatives are reviewed along with some applications in analytical separations.