2-羟基-5-甲基-5-(4-甲基戊烯-3-)基四氢呋喃的合成

本文研究了一类羰基化合物-酮类为原始料(选用了来源丰富, 价格低廉的6-甲基-5-庚烯酮-2), 经格氏反应水解, 环化及醚化即合成了2-羟基-5-(4-甲基戊烯-3-)基四氢呋喃。     

蛋氨酸合成酶催化反应研究VII.5-氨基-6-甲基尿嘧啶的合成研究

报道了5-氨基-6-甲基尿嘧啶简便的合成方法。该化合物以6-甲基尿嘧啶（2） 为起始物，经硝化或重氮化分别得到了中间体5-硝基-6-甲基尿嘧啶（3）和5-偶氮 苯基-6-甲基尿嘧啶(4)，化合物3和4经Na_S_2O_4还原，合成产物5-氨基-6-甲基尿 嘧啶（1）。     

水中3-甲基-6-氨基-5-氰基-4-芳基-1-苯基-1，4-二氢吡喃[2，3-c]吡唑的洁净合成

在水溶剂中并有三乙基苄基氯化铵（TEBA）存在下，取代芳亚甲基丙二腈与3- 甲基-1-苯基-2-吡唑啉-5-酮缩合成为3-甲基-6-氨基-5-氰基-4-芳基-1-苯基-1， 4-二氢吡喃[2,3-c]吡唑，此法为相应化合物的合成提供了一种快速、方便、高效 和洁净的方法。     

β-环香叶酰氯与有机金属试剂(锰、锌、镉)合成2,6,6-三甲基-1-烷酰基环己烯

2,6,6-三甲基-1-烷酰基环己烯是名贵香料,本文报道通过β-环香叶酰氯与有机金属化合物(RMnI,R_2Zn,R_2Cd)合成该类化合物的新方法。产物的(IR、~1H NMR、MS)分析表明,反应过程中有双键转移发生。根据收集到的烷烃气体和对中间体的验证,提出了消除加成与亲核取代并存的反应机理。用此法合成了一系列2,6,6-三甲基-1-烷酰基环己烯,这些化合物都具有强烈而愉快的木香、花香香气。新的合成路线具有收率较好,操作简便,产物易提纯等优点。     

2-(N-三氟乙酰-N-三甲基硅烷基)氨基-3-三甲基硅烷氧基-羧酸三甲基硅烷酯和2-(N-三氟乙酰)-2,3-脱氢氨基酸的合成

利用三氟甲基磺酸三甲基硅烷酯, 我们合成了一种新的、化学活性很高的合成中间产物2-(N-三氟乙酰-N-三甲基硅烷基)氨基-1, 1-二(三甲基硅烷氧基)乙烯。脂肪醛或芳香醛发生碳碳成键的加成反应, 生成β碳原子上带有易离去基团三甲基硅烷氧基、N原子上带有保护基团三氟乙酰基的α氨基酸三甲基硅烷酯。消除反应得到了一个合成α、β脱氢氨基酸的可行途径。这类化合物是合成复杂多肽和肽生物碱的基元物。     

5,7-二甲基-1,2,4-三唑并[1,5-a]嘧啶-2-硫乙酰腙类 衍生物的合成及生物活性 研究

以2-巯基-5,7-二甲基-1,2,4-三唑并[1,5-a]嘧啶为起始原料,设计合成了16种新型的-5,7-二甲基-1,2,4-三唑并[1,5-a]嘧啶-2-硫乙酰腙类衍生物,其结构均经1^HNMR,MS及元素分析确证。通过核磁共振氢谱分析及分子力学优化,对该类化合物在溶液中的顺反异构体的化学位移进行了归属。初步生测结果表明,所合成的化合物均表现出不同程度的除草及杀菌活性,尤其是在50×^-6浓度下所有化合物都对水稻纹枯病表现出很好的抑制效果。对化合物4c和4o活体小株实验结果表明,在先接菌后施药的处理方式下,化合物在50×^-6和100×^-6浓度下对水稻纹枯病的防效均优于多菌灵和井冈霉素,在100×^-6浓度下的防效达到了80%以上。     

手性亚砜法合成粉 虫性信息素

5-氯-2-戊酮(2)经四步反应制得(R)-(+)-4-甲基-3-戊烯基对甲苯基亚砜(6), 化合物6与乙醛进行不对称加成反应得手性醇(7), 7经兰尼镍还原性脱硫反应即合成出目标产物粉 虫性信息素(1), 其光学纯度可达45%。     

醇酮环合法合成dl-麝香酮

麝香酮(β-甲基环十五烷酮)是天然麝香的组成成分,并具有天然麝香某些重要的药理作用,本文报道它的合成工艺和纯化的研究。有关麝香酮的合成方法,国内外报道很多^[1]。我们选用α,ω-长链二元酸酯进行醇酮环合法制备dl-麝香酮。早先Stoll和Commarmont^[2]报道用β-甲基十五烷二酸双乙酯经醇酮环合法合成dl-麝香酮。     

α-亚甲基-γ-丁内酰胺衍生物的合成进展

α-亚甲基-γ-丁内酰胺衍生物具有细胞毒性、抗肿瘤等生理活性, 有关这些化合物的合成方法一直是人们感兴趣的课题之一。本文拟就(1)含必要官能团的开链前体的成环反应, (2)现成的γ-丁内酰胺的α-亚甲基化反应等两个方面对α-亚甲基-γ-丁内酰胺的合成方法进行综述。     

酰氨基硫脲及有关的杂环衍生物的研究 I:1-氰乙酰基-4-芳基氨基硫脲及有关的杂环衍生物的合成

合成了九个1-氰乙酰基-4-芳基氨基硫脲类化合物和四个3-氰甲基-4-芳基-1,2,4-三唑啉与硫酮类化合物和四个2-苯基氨基-5-取代-1,3-噻二唑类化合物.并初步研究了这些化合物的抗结核菌活性和植物生长促进作用.     

4,7-二苯基-1,10-菲啰啉的合成研究

以4-苯基-8-硝基喹啉为起始原料,经还原得到4-苯基-8-氨基喹啉,再以I2/KI为氧化剂,在乙酸和盐酸的存在下,用Skraup法合成了4,7-二苯基-1,10-菲啰啉.化合物结构经IR和1H NMR得到了证实.实验研究得到了最佳的合成条件为:n(3-氯苯丙酮)∶n(4-苯基-8-氨基喹啉)=1.5∶1,I2/KI用量为8%,反应温度120℃,反应时间2.5 h.产品收率可达82%.     

苏丹红I分子印迹聚合物的制备及其性能评价

以苏丹红I为模板分子,通过沉淀聚合法制备了一种对苏丹红I具有特异性吸附的分子印迹聚合物。通过选择性评价和前沿色谱实验,评价了致孔剂的选择和用量、功能单体和模板分子的物质的量比对分子印迹聚合物识别性能的影响。实验结果表明: 当以甲醇和乙腈的混合液(体积比为30:10)为致孔剂,甲基丙烯酸(MAA)为功能单体,且功能单体和模板分子的物质的量比为8:1时,分子印迹聚合物的印迹因子为2.32,亲和位点总数(Bt)为0.50 μmol/g;将其作为固相萃取柱填料用于辣椒粉样品中痕量苏丹红I的净化和富集,结果表明: 苏丹红I浓度在10～500 μmol/L范围内时,呈现良好的线性关系(r=0.999);检出限为3.3 μmol/L,加标回收率为95.87%～98.41%,相对标准偏差低于3.1%。该方法有望用于辣椒粉样品中苏丹红I添加剂的常规检测。     

Determination of total thallium in fresh water by electrothermal atomic absorption spectrometry after colloid precipitate flotation

Tl(I) and Tl(III) are preconcentrated simultaneously from aqueous solutions by colloid precipitate flotation using two collectors: hydrated iron(III) oxide (Fe₂O₃·xH₂O) and iron(III) tetramethylenedithiocarbamate (Fe(TMDTC)₃). After the coprecipitation step and the addition of foaming agents, Tl(I) and Tl(III) were separated from the water by a stream of air bubbles. Various factors affecting Tl(I) and Tl(III) recoveries during the separation from water, including the collector mass, the nature of the supporting electrolyte, pH, ζ potential of the collector particle surfaces, type of tenside, etc., were investigated. Within the optimal pH range (6–6.5), establishing by a recommended procedure, Tl(I) and Tl(III) were separated quantitatively (94.9–100.0%) with 30 mg Fe(III). Both Tl ions were simultaneously separated without any previous conversion of one type of Tl ion to the other. Total Tl determination was performed by electrothermal atomic absorption spectrometry by previous matrix modification of the concentrated samples. The determination limit of Tl by this method is 0.108 μg l⁻¹.     

Part I: Ni-Co alloy foils electrodeposited using ionic liquids

The Ni-Co alloy co-electrodeposit from a sulfate bath including two new ionic liquids 1-methyl-3-(2-oxo-2-((2,4,5 trifluorophenyl) amino) ethyl)-1H-imidazol-3-ium iodide [MOFIM]I and 1-(4-fluorobenzyl)-3-(4-phenoxybutyl) imidazol-3-ium bromide [FPIM]Br as additives was characterized using the SEM, EDS, EDS mapping, XRD, AFM and microhardness measurement techniques. The resultant surface morphologies in acidic sulfate baths on a copper substrate demonstrated that both the [MOFIM]I and [FPIM]Br additives served as effective leveling agents. The Ni-Co alloy co-deposit morphology in the [MOFIM]I bath was more enhanced (non-grained coating, R_a of 28 nm and R_t of 35.5 nm) than that in the [FPIM]Br bath (grain size 225 nm, R_a of 51. 1 nm and R_t of 65.7 nm) owing to the molecular structure. The co-deposition of Co and Ni from the acidic baths was of the anomalous type. Moreover, the anomalous behavior of the Ni-Co co-deposition was alleviated after [MOFIM]I and [FPIM]Br were introduced in the bath. To determine the optimal bath conditions, the cathodic current efficiency (CCE%) value was calculated during the Ni-Co alloy co-electrodeposition process under three different compositions and different operating conditions. Under the composition of Ni 70% and Co 30% (Ni70%-Co30% alloy deposit), the CCE% values increased considerably, with maximum values of 99.8% and 97.07% in the baths including [MOFIM]I and [FPIM]Br, respectively.     

Colorimetric method for the simultaneous determination of chlorphenoxamine hydrochloride and anhydrous caffeine in pure and dosage forms with rose bengal

A rapid, simple and sensitive colorimetric method for the simultaneous determination of chlorphenoxamine HCl and anhydrous caffeine was developed, based on charge-transfer complex formation of the drugs with rose bengal in basic media of pH 9.0. The chlorphenoxamine HCl (I) complex was measured at 588 nm whereas anhydrous caffeine (II) was measured at 551 nm. The optimal experimental parameters for colour production were studied. Beer's law was obeyed in the concentration ranges 2–40 and 2–34 g ml^–1 for I and II, respectively. The Ringbom optimum concentration ranges were 3–36 and 3–30 g ml^–1 for I and II, respectively. The results obtained showed good recoveries of 100.2 ± 1.5 and 99.7 ± 1.3% with relative standard deviations of 0.37 and 0.47% for I and II, respectively. Applications of the method to representative pharmaceutical dosage forms are presented and the validity assessed by applying the standard addition technique.     

Preparation of Al2O3-supported nano-Cu2O catalysts for the oxidative treatment of industrial wastewater

Cuprous oxide (Cu₂O) nanoparticles supported on Al₂O₃ prepared using two different methods (hereafter referred to as catalyst I and II, respectively) were characterized by XRD and TEM. The catalytic activities of catalyst I and II during the treatment of industrial wastewater were then investigated. Specifically, the progress of the catalytic oxidation of industrial wastewater was observed by monitoring the time-dependent change in the chemical oxygen demand (COD) of industrial wastewater when the catalysts were applied. The results indicated that the catalytic activity of catalyst II was greater than that of catalyst I. Furthermore, under optimal conditions the COD removal efficiency was 94.59%. Finally, the mechanism by which the oxidative degradation of the industrial wastewater occurred could be explained based on a hydroxyl radical mechanism.     

两种水产品中农药多残留分析的样品前处理方法及其在111种农药和相关化学品残留同时检测中的应用

建立了两种针对水产品中农药多残留分析的快速样品前处理方法,并将其应用于111种农药及相关化学品残留检测。在样品前处理方法Ⅰ中,样品经丙酮-乙酸乙酯-正己烷(体积比为1∶1∶1)混合溶剂提取,乙腈转溶;在样品前处理方法Ⅱ中,样品用乙腈-水溶液均质,超声波辅助提取,液-液分配。两种方法所得到的提取液分别用Envi-18柱和PSA柱净化后进行气相色谱-质谱(GC-MS)分析。采用选择离子扫描(SIM)方式,外标法定量。该方法简便、快速,在优化的样品前处理条件和GC-MS分析条件下,方法的检出限(S/N=3)为0.001～0.026 mg/kg;在加标水平为0.25 mg/kg时,采用方法Ⅰ时的回收率为72%～113%,相对标准偏差（RSDs）为3.4%～12.1%;采用方法Ⅱ时的回收率为51%～127%(其中回收率为70%～120%的占94%),RSDs为3.2%～13.8%。     

Combination of pharmacophore modeling and 3D-QSAR analysis of potential glyoxalase-I inhibitors as anticancer agents

Glyoxalase system is an ubiquitous system in human cells which has been examined thoroughly for its role in different diseases. It comprises two enzymes; Glyoxalase I (Glo-I) and Glyoxalase II (Glo-II) which perform detoxifying endogenous harmful metabolites, mainly methylglyoxal (MG) into non-toxic bystanders. In silico computer Aided Drug Design approaches were used and ninety two diverse pharmacophore models were generated from eighteen Glyoxalase I crystallographic complexes. Subsequent QSAR modeling followed by ROC evaluation identified a single pharmacophore model which was able to predict the expected Glyoxalase I inhibition. Screening of the National Cancer Institute (NCI) database using the optimal pharmacophore Hypo(3VW9) identified several promising hits. Thirty eight hits were successfully predicted then ordered and evaluated in vitro. Seven hits out of the thirty eight tested compounds showed more than 50% inhibition with low micromolar IC₅₀.     

利用微波消解和高效液相色谱荧光检测法测定环境水样中痕量硒

基于微波消解和正相液相色谱－荧光检测测硒法,实现了对环境水样中亚纳克级硒的测定。考察了ＨＮＯ３和Ｈ２ＳＯ４－Ｈ２Ｏ２两种消化体系及其工作条件,方法检出限分别可达 ７．２和 １０．４ ｐｇ Ｓｅ,对标准参考物质的回收率分别为９９．４±２．０和９７．８±２．５％,在０～１．５ｎｇＳｅ范围内有线性关系（Ｒ２＜０．９９６）。对北京地区 ４种不同类型水体水样含硒量进行了分析测定（２ｍＬ样品）,其浓度范围为 ０．２０～０．９０μｇ／Ｌ,标准加入回收率为９９．１％～１０３．４％。     

驱油体系的驱油效率及其在模拟岩芯表面的润湿性研究

In order to research the flooding efficiency of flooding systems and wettability on the simulant rock surface,the orthogonal-test-design method was used to determine the optimal formula for the crude oil from the Chunliang zone of Shengli oil field by transient interfacial tension（IFT）. The results indicate that two optimal formulas are naturally mixed carboxylate SDC-V（0.35%,0.36%）,nonionic surfactant FBB（0.06%,0.07%）,Alkaline NaHCO3 / Na2CO3 weight ratio of（0.8%,1.2%）and HPAM（0.05%,0.15%）,and in the coreflood experiment,their oil recovery are（14.6%,16.7%）OOIP respectively. The contact angles have been determined for the two optimal formula systems and their components on the simulant rock surface,which points out the relationship between the flooding efficiency and contact angle is showed identification,that is,the more oil recovery the less contact angle. It will be useful to the application research of microgravity.