不同表面活性剂对多巴胺电化学行为的影响

利用循环伏安法(CV)制备了银掺杂聚L-半胱氨酸修饰电极,以神经递质药物多巴胺(DA)为探针,研究了DA分别在阳离子表面活性剂十六烷基三甲基溴化铵(CTMAB)、阴离子表面活性剂十二烷基硫酸钠(SDS)和非离子表面活性剂TritonX-100存在下,在修饰电极上的电化学行为。结果表明,在阳离子表面活性剂和阴离子表面活性剂及非离子表面活性剂中,DA的氧化还原电位变化不大,峰电流有所降低,且对峰电流的影响CTMAB最大、SDS最小。     

表面活性剂对硫醇单层膜修饰金电极电化学行为的影响

利用自组装方法在金电极表面制备成硫醇单层膜, 循环伏安和交流阻抗实验表明硫醇单层膜与表面活性剂十六烷基三甲基溴化胺作用后, 其电化学行为发生变化, 对于带有不同电荷的探针分子, 表现出一定的选择性响应. 即使是带有相同电荷的探针分子, 由于与表面活性剂的作用方式不同, 也使它们通过硫醇单层膜在电极表面产生电化学响应的程度完全不同.     

表面胶团修饰电极电化学测定双酚A的增敏机理及抗污性能研究

分别以2种阴离子表面活性剂(SDS、SDBS)、3种季铵盐阳离子表面活性剂(CTAB、TTAB、DTAB)和2种季铵盐型双子表面活性剂(12-3-12、12-4-12)修饰碳糊电极。通过原子力显微镜、接触角以及分析物在电极表面的电化学行为探讨了不同表面活性剂在电极表面的吸附情况,推测在浓度大于临界胶束浓度(CMC)时,季铵盐型阳离子表面活性剂CTAB、TTAB、12-3-12和12-4-12在碳糊电极表面形成了圆柱形的表面胶团,而DTAB和SDS可能是饱和单分子层吸附。以BPA为分析物,研究了表面活性剂修饰电极对BPA的电化学增敏机理,结果表明修饰电极对双酚A(BPA)的电化学增敏作用主要是因为表面胶团对BPA的增溶作用,表面活性剂和BPA间的阳离子-π作用是表面胶团增溶BPA的主要原因。     

基于表面活性剂单分子层修饰碳糊电极的一氧化氮电化学传感器及其应用

报道了一种表面活性剂单分子层修饰碳糊电极,并用于NO的高灵敏电化学检测。研究表明,表面活性剂通过烷基链在电极表面形成的疏水性单分子层微环境对NO的电化学响应具有较好的促进作用。其中,阳离子表面活性剂十六烷基三甲基溴化铵(CTAB)对NO的电化学氧化表现出最强的催化活性和增敏作用。在Nafion膜覆盖的CTAB修饰碳糊电极上,NO的安培响应与其浓度在3.6×10-8～1.8×10-5mol/L范围内呈良好的线性关系,检出限为1.8×10-8mol/L。该电极作为低成本、高灵敏的NO电化学传感器,被成功应用于大鼠肺组织细胞中NO释放的实时监测。     

维生素B_1自组装膜修饰金电极对多巴胺、尿酸的电催化作用

用维生素B1(VB1)在金电极上进行自组装,制备了VB1自组装膜修饰金电极(VB1-Au/SAMs/CME).利用循环伏安法初步研究了此自组装单分子膜修饰电极的电化学行为.结果表明: VB1在金电极表面具有特性吸附.以\3-/ 4-氧化还原电对为探针,考察了VB1自组装膜修饰金电极的电化学性质, VB1自组装膜的存在对\3-/4-的电子转移具有明显的阻碍作用.研究了多巴胺(DA)和尿酸(UA)在此电极上的电化学行为.实验结果表明, DA和UA在此电极上均可被电催化氧化.差分脉冲伏安(DPV)氧化峰电流与DA浓度在2.0×10-5～4.0×10-4 mol/L范围内呈线性关系;测定UA的线性范围为6.0×10-5～2.2×10-4 mol/L,而且可实现这两种物质的同时测定.     

界面可控硫醇SAMs纳米金修饰金电极的电化学行为研究

在裸金电极上自组装不同比例的4,4’-二甲基联苯硫醇(MTP)和硫辛酸(TA)混合液,形成自组装膜(MTP+TA/Au SAMs),再修饰纳米金,制得纳米金混合巯基修饰金电极(AuNPs/MTP+TA/Au)。研究了纳米金混合巯基修饰金电极的电化学行为和阻抗行为,结果表明电极表面pH值的改变对电极表面的电子转移有重要影响。对葡萄糖传感器的制备条件、测定条件、抗干扰能力等进行了讨论,结果表明修饰电极的微结构和微环境有必要进一步研究。     

Study on Electrochemical Behavior of Controllable Interface Alkanethiols Selfassembled Monolayers and Au Nanoparticles Modified Gold Electrode

在裸金电极上自组装不同比例的4,4’-二甲基联苯硫醇(MTP)和硫辛酸(TA)混合液,形成自组装膜( MTP+ TA/Au SAMs),再修饰纳米金,制得纳米金混合巯基修饰金电极(AuNPs/MTP+ TA/Au).研究了纳米金混合巯基修饰金电极的电化学行为和阻抗行为,结果表明电极表面pH值的改变对电极表面的电子转移有重要影响.对葡萄糖传感器的制备条件、测定条件、抗干扰能力等进行了讨论,结果表明修饰电极的微结构和微环境有必要进一步研究.     

一氯乙酸和三氯乙酸在富勒烯/DDAB膜修饰电极上的电催化

研究了由阳离子表面活性剂双十二烷基二甲基溴化铵分别和C60或C70在玻碳电极表面形成的膜在0．5mol／L KCl溶液中的电化学,发现在0～-1．0V范围内,有两对峰形较好的还原再氧化峰。实验结果表明,该修饰电极有较好的稳定性和重现性,对三氯乙酸和一氯乙酸的还原,表现出良好的电催化去卤化作用,说明修饰电极上的富勒烯是良好的电子传递媒介体。     

亚硒酸钠在L-半胱氨酸自组装类生物膜修饰电极上的电化学行为

利用L-半胱氨酸自组装膜修饰金电极(L-Cys,Au/SAMs), 在0.05mol/L H_2SO_4 底液中研究了 Na_2SeO_3 的电化学特性.在0.00～1.30 V (vs. SCE) 电位范围内对微量Na_2SeO_3进行循环伏安扫描,发现L-Cys, Au/SAMs修饰电极在峰电位0.89 V处有灵敏的Se的氧化溶出峰.通过比较裸金电极和修饰电极在Na_2SeO_3 溶液中的电化学特性发现,修饰电极通过巯基中的S与Na_2SeO_3发生氧化还原作用生成Se,且修饰电极对沉积在电极表面的Se的氧化过程具有催化作用.根据Na_2SeO_3在单分子膜上的电化学行为,提出了单分子膜中硫(Au-S)与Se(Ⅳ)作用生成Se的反应机理、Se电化学催化氧化机理及巯基化合物通过生成纳米硒生物吸收Se的类生物膜模型.     

生物素衍生物自组装膜制备及其覆盖度的电化学测定

利用循环伏安法和电化学交流阻抗谱研究了MBDA/Au,MBTA/Au,TBDA/Au,TBTA/Au修饰电极以及MBDA与DT混合自组装/Au、TBTA与DT混合自组装/Au修饰电极的覆盖度。结果表明这些自组装膜在金电极表面的覆盖度均比较高,达到99%以上;对同一类修饰电极,混合自组装膜的覆盖度高于单组分自组装膜的覆盖度,混合自组装体系的覆盖度随着DT比例的增加而增加;同类物质,长链化合物在金表面的覆盖度大于短链化合物,含二硫键的化合物与金电极的键合能力比含一个巯基的化合物键合能力强。     

Electrocatalytic activity of three-dimensional monolayer of 3-mercaptopropionic acid assembled on gold nanoparticle arrays

3-Mercaptopropionic acid (MPA) was assembled on gold nanoparticle arrays to form three-dimensional monolayer. The electrochemical behavior of small biomolecules such as NADH, ascorbic acid (AA), uric acid (UA) and dopamine (DA) on the as-prepared three-dimensional monolayer was studied. The cyclic voltammetric results indicated that three-dimensional MPA monolayer promoted the electron transfer between NADH and electrode, which was similar to two-dimensional MPA monolayer assembled on planar gold electrode. However, to the electrooxidation of AA, although two-dimensional MPA monolayer exhibited a blocking effect, three-dimensional MPA monolayer showed an obvious promotion. The catalytic activity of three-dimensional MPA monolayer towards UA and DA was also observed, which was attributed to its three-dimensional structure that might effectively prevent the poison of the electrode surface by the oxidation products.     

Voltammetric Study of Methylene Blue at Thiol SAMs‐Modified Gold Electrodes

The voltammetric behavior of methylene blue (MB) at thiol self‐assembled monolayers modified gold electrodes (SAMs/Au) has been investigated. MB exhibited a redox peak at about ?0.35 V (vs.SCE) in alkaline solution at bare gold electrodes. When the gold electrodes were modified with thiol SAMs, the peak grew due to the accumulation of MB at SAMs. With the solution pH rising, more MB was accumulated, hence the peak height increased, which differed from that at bare gold electrodes. The electrode process at SAMs/Au featured the characteristics of adsorption and/or electrode reaction controlled. The enhancing action of glutathione monolayer (GSH SAM), 3‐mercaptopropionic acid monolayer (3MPA SAM) and other thiol SAMs was compared. Among these, GSH SAM made the MB peak increase more. At GSH SAM/Au, the peak height varied linearly with MB concentration over the range of 2 μM to 400 μM. So this can be developed for the determination of MB and studies concerned. The accumulation behavior caused by GSH SAM and native fish sperm dsDNA was compared. The interaction between DNA and MB was also discussed under this condition.     

Voltammetric investigation of cytochrome c on gold coated with a self-assembled glutathione monolayer

The direct, reversible electrochemistry of horse-heart cytochrome c (cyt. c) was realized on a self-assembled glutathione (GSH) monolayer modified Au electrode. The voltammetric responses of cyt. c on GSH/Au electrode were found to be affected by pH during the electrode modification, metal ions and surfactants. Using potassium ferricyanide [K4Fe(CN)6] as a probe, these effects on the voltammetric responses of cyt. c were characterized by electrochemical methods. It was found that the pH during the electrode modification, metallic ions and surfactants changed GSH monolayer's charge state and the conformation on the electrode surface, and resulted in the influence on the voltammetric responses of cyt. c. The experimental results provided us information to understand the mechanism of the interfacial electron transfer of electrode-protein, as well as the electron transfer of cyt. c in life system.     

Comparative study on the interaction of DNA with three different kinds of surfactants and the formation of multilayer films

The interactions between double-stranded DNA (dsDNA) and three different kinds of surfactants, i.e., cationic, anionic, and nonionic surfactants, were investigated by cyclic voltammetry, electrochemical impedance spectroscopy and UV-vis spectroscopy. Multilayer films composed of DNA and surfactants were prepared at gold electrode by electrostatic or hydrophobic interactions. It was found that the cationic surfactant, CTAB, can bind to DNA by electrostatic interaction, and the electron transfer resistance of CTAB-DNA complex film increases first and then decreases with CTAB concentration. The anionic surfactant, LAS, can bind to DNA but by hydrophobic interaction, and the electron transfer resistance of the complex film keeps decreasing with LAS concentration. Nonionic surfactants can also directly bind to DNA by hydrophobic interaction. All the three different kinds of surfactants can form multilayer films with DNA on the electrode surface. The chemical structure of DNA keeps unchanged during interacting with these surfactants. The binding modes of DNA with these three different kinds of surfactants were also deduced.     

Electorchemical Studies of Cytochrome c on Electodes Modified by Single—Wall Carbon Naotubes

Single-wall carbon nanotubes(SWNTs) modified gold electrodes were prepared by using two different methods.The electrochemical behavior of cytochrome c on the modified gold electrodes was investigated.The first kind of SWNT-modified electrode (noted as SWNT/Au electrode)was prepared by the adsorption of carboxylterminated SWNTs from DMF dispersion on the gold electrode.The oxidatively processed SWNT tips were covalently modified by coupling with amines (AET) to form amide linkage.Via Au-S chemical bonding,the self-assembled monolayer of thiol-unctionalized nanotubes on gold surface was fabricated so as to prepare the others SWNT-modified electrode (noted as SWNT/AET/Au electrode).It was shown from cyclic voltammetry cxperiments that cytochrome c exhibited direct electrochemical responses on the both electrodes, but only the current of controlled diffusion existed on the SWNT/Au electrode while both the currents of controlled diffusion and adsorption of cytochrome c occurred on the SWNT/AET/Au electrode.Photoelastic Modulation Infared Reflection Absorpthion Spectroscopy (PEM-IRRAS) and Quartz Crystal Microbalance (QCM) were employed to verify the adsorption of SWNTs on the gold electrodes.The results proved that SWNTs could enhance the direct electron transfer proecss between the electrodes and redox proteins.     

Achieving Direct Electrical Connection to Glucose Oxidase Using Aligned Single Walled Carbon Nanotube Arrays

Direct electron transfer between an electrode and the redox active centre of glucose oxidase, flavin adenine dinucleotide (FAD), is probed using carbon nanotube modified gold electrodes. Gold electrodes are first modified with a self‐assembled monolayer of cysteamine and then shortened single walled carbon nanotubes (SWNT) are aligned normal to the electrode surface by self‐assembly. The electrochemistry of these aligned nanotube electrode arrays is initially investigated using potassium ferricyanide which showed SWNT act as nanoelectrodes with the ends of the tubes more electrochemically active than the walls. Subsequently the nanotubes are plugged into the enzymes in one of two ways. In the first method, native glucose oxidase is covalently attached to the ends of the aligned tubes which allowed close approach to FAD and direct electron transfer to be observed with a rate constant of 0.3 s^?1. In the second strategy, FAD was attached to the ends of the tubes and the enzyme reconstituted around the surface immobilized FAD. This latter approach allowed more efficient electron transfer to the FAD with a rate constant of 9 s^?1.     

Voltammetry and EQCM Investigation of Glutathione Monolayer and Its Complexation with Cu2+

The glutathione (GSH) self‐assembled monolayer and its compexlation with Cu²⁺ were studied by using voltammetry and EQCM. It was found that the monolayer could rearrange during the redox process of Cu²⁺/Cu⁺. The protonating, or not, of the carboxyl terminates of the adsorpted GSH molecules influence the compexlation interaction significantly for they are the key binding sites. The GSH monolayer had the capacity to accumulate Cu²⁺ and the monolayer modified gold electrode was employed to detect the low levels of Cu²⁺ with a limit of 1.0×10^?10 mol L^?1.     

Effects of surfactants on the electroreduction of dioxygen at an acetylene black electrode.

An acetylene black electrode modified by an adsorbed cationic surfactant, cetyltrimethylammonium bromide (CTAB), was developed. The influences of various types of surfactants on the electroreduction of O2 were investigated. It was demonstrated that a cationic surfactant, CTAB, on the surface of the electrode could significantly decrease the overpotential of dioxygen reduction, and the reduction peak current of O2 was also remarkably increased. The reduction of O2 at a CTAB modified acetylene black electrode was studied using cyclic voltammetry, chronocoulometry and controlled potential coulometry. The total number of electrons, the exchange current density (j(o)) and the transfer coefficient (alpha) for reduction of O2 at the surface of this modified electrode were determined.     

Self-assembled supramolecular array of polymeric phthalocyanine on gold for the determination of hydrogen peroxide

This Article describes for the first time the formation of a supramolecular self-assembled monolayer of polymeric phthalocyanine (poly(CuPc)) onto a gold substrate. The latter is established through the interaction of the cyano group, belonging to the poly(CuPc), with the metal substrate. The functionalized gold substrate was characterized using Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), and electrochemical methods. Results clearly demonstrated the interaction between gold and the nitrogen atom of cyano group and showed at the same time the formation of a completely covered polymeric monolayer on the gold surface. In addition, the modified gold surface seems to exhibit a reversible redox behavior and is found to act as an electronic conductor, which allows rapid electron transfer. Electrochemical impedance spectroscopy (EIS) analyses in the presence of [Fe(CN)(6)](3-/4-) as a redox couple revealed that the modified electrode showed a much lower electron transfer resistance compared with bare gold. In addition, the modified electrode is found to catalyze the H(2)O(2) reduction very effectively, showing a catalytic current that varies linearly with the peroxide concentration in the range of 0.35 to 70 μM with a detection limit of 0.25 μM.