Study on elastic modulus of crosslinked polyurethane/organoclay nanocomposites

In this paper, two polyurethane/clay nanocomposite systems with crosslinked structure were synthesized via in situ polymerization of a polyether‐ as well as a polyester‐based prepolymer with methylene‐bis‐ortho‐chloroanilline (MOCA). Two types of modified clays with different organic modifiers were used in order to see the effect of compatibility between polymer matrix and clays on elastic modulus of nanocomposites. The morphology and the dispersion of clay layers in polyurethanes have been characterized by X‐ray diffraction (XRD) and microscopic techniques. The changes of elastic modulus of nanocomposites with clay content were examined and compared with those predicted by some conventional composite models. The results showed a reasonable fitting of experimental and theoretical values only at very low clay contents. As the clay content exceeds 1.5 wt% in this system, a reduction in elastic modulus was experimentally observed due to insufficient dispersion degree of silicate layers throughout the crosslinked matrix. This behavior was not predicted with the conventional composite theories. A new model on the basis of Wu model was then developed in order to predict the reduction of elastic modulus at various clay contents in crosslinked PU matrix. This model fitted reasonably the experimental results. Copyright © 2010 John Wiley & Sons, Ltd.     

Dispersibility of clay and crystallization kinetics for in situ polymerized PET/pristine and modified montmorillonite nanocomposites

Nanocomposite materials composed of poly (ethylene terephthalate) (PET) and montmorillonite (MMT) clays were prepared by in situ polymerization. Samples consisted of PET blended with various quantities of either pristine (Na⁺‐MMT) or organically modified MMT (A10‐MMT). The morphology and thermal and mechanical properties were evaluated for each sample. TEM micrographs, acquired at a 20 nm resolution, provide direct evidence of exfoliation of the clay particles into the PET matrix and show the effect of the alkyl‐modifier on clay dispersibility. The dispersion of PET/A10‐MMT was greater than that observed for the PET/Na⁺‐MMT nanocomposites. The greatest degree of exfoliation occurred for PET/A10‐MMT 0.5 wt %. However, PET/Na⁺‐MMT exhibited higher crystallization temperatures and rates suggesting that Na⁺‐MMT is a more efficient nucleating agent. Both mechanically and thermally, PET/A10‐MMT nanocomposites exhibited superior properties over pure PET. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1022–1035, 2008     

Preparation and properties of organo‐modifier free PET/MMT nanocomposites via monomer intercalation and in situ polymerization

In order to prevent the properties, especially transparency, color and health security, of PET/clay nanocomposites from being deteriorated due to the thermal degradation of clay organo‐modifer, we had directly modified sodium montmorillonite (Na⁺‐MMT) with PET's monomer, bis (hydroxyethyl) terephthalate (BHET) which had a degradation temperature higher than 400°C, and successfully prepared the hybrids via in situ polymerization. Nanodispersion of clay and the intercalated morphology were determined, and compared with PET/Na⁺‐MMT hybirds in which Na⁺‐MMT was directly added without any treatment. Improved mechanical properties and T_g were observed for the prepared PET/ BHET‐modified clay composites. More importantly, the film produced from the composites had the same transparency as that of pure PET even when 2 wt% of clay was added. Non‐isothermal and isothermal crystallization experiments showed a very good neculation capability of the nano‐dispersed clay, particularly at higher crystallization temperatures. Copyright © 2009 John Wiley & Sons, Ltd.     

Mechanical and thermal properties of attapulgite clay reinforced polymethylmethacrylate nanocomposites

To investigate the dispersion and nanofillers' interaction of rod‐like silicates (attapulgite, ATT) in the polymethylmethacrylate (PMMA) matrix, a novel in situ modification of ATT by toluene‐2,4‐di‐isocyanate (TDI) using mechanical mixing was exploited, which resulted in homogeneous dispersion and rod‐like texture of ATT nanorods. As a consequence, organo‐modified ATT/PMMA nanocomposites were prepared, which provided prominent improvements in strength, toughness, and thermal stability. High grafting efficiency of TDI on ATT surface was confirmed by FTIR spectra and SEM observations. The uniform dispersion of in situ TDI modified ATT nanorods in the PMMA which was clearly visible in the TEM micrographs, influenced the mechanical and thermal properties of the nanocomposites. The fibrous nanoparticles significantly confined the segmental motion, causing a 13.20°C increase in the glass transition temperature of 2 wt% in situ TDI modified ATT/PMMA nanocomposites. But at higher loadings little or no differences were observed for the reinforcement benefits provided by the in situ TDI modified ATT clay. By comparison, pre‐treated ATT clay severely fractured during mechanical mixing and showed little reinforcement benefits. Copyright © 2010 John Wiley & Sons, Ltd.     

Preparation and characterization of PP/clay nanocomposites based on modified polypropylene and clay

X‐ray diffraction and differential scanning calorimeter (DSC) methods have been used to investigate the crystallization behavior and crystalline structure of hexamethylenediamine (HMDA)‐modified maleic‐anhydride‐grafted polypropylene/clay (PP‐g‐MA/clay) nanocomposites. These nanocomposites have been prepared by using HMDA to graft the PP‐g‐MA (designated as PP‐g‐HMA) and then mixing the PP‐g‐HMA polymer in hot xylene solution, with the organically modified montmorillonite. Both X‐ray diffraction data and transmission electron microscopy images of PP‐g‐HMA/clay nanocomposites indicate that most of the swellable silicate layers are exfoliated and randomly dispersed into PP‐g‐HMA matrix. DSC isothermal results revealed that introducing 5 wt % of clay into the PP‐g‐HMA structure causes strongly heterogeneous nucleation, which induced a change of the crystal growth process from a three‐dimensional crystal growth to a two‐dimensional spherulitic growth. Mechanical properties of PP‐g‐HMA/clay nanocomposites performed by dynamic mechanical analysis show significant improvements in the storage modulus when compared to neat PP‐g‐HMA. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3242–3254, 2005     

Synthesis and Rheology of Intercalated Polystyrene/Na+‐Montmorillonite Nanocomposites

Polystyrene (PS)/clay nanocomposites were synthesized by the emulsion polymerization of styrene in the presence of sodium ion‐exchanged montmorillonite (Na⁺‐MMT), demonstrating that the strongly hydrophobic PS was intercalated into the hydrophilic silicate layers. The nanocomposites were examined by means of X‐ray diffraction, transmission electron microscopy, thermogravimetric analysis. The rheological properties of the PS/Na⁺‐MMT nanocomposites were also studied to exhibit more pronounced shear thinning behavior with increasing clay content.     

Structure and properties of some novel fluoroelastomer/clay nanocomposites with special reference to their interaction

In the present work, rubber/clay nanocomposites were prepared by a solution mixing process using fluoroelastomers and different nanoclays (namely, Cloisite NA+, Cloisite 10A, Cloisite 20A, and Cloisite 30B). Fluoroelastomers having different microstructure and viscosity (Viton B‐50, Viton B‐600, Viton A‐200, and VTR‐8550) were used. Characterization of the nanocomposites was done by using X‐ray diffraction and atomic force microscopy. The mechanical and dynamic mechanical properties were studied. The surface energy of the clays and the elastomer was also measured. Even with the addition of only 4 phr of clay in Viton B‐50, tensile strength and modulus improved by 30–96% and 80–134%, respectively, depending on the nature of the nanoclays. Exfoliation was observed with both the unmodified and the modified clays at low loading in all the fluoroelastomers. Best properties were observed with the unmodified clay. All the grades of fluororubber followed the same trend. The increment (19%) in storage modulus was also higher in the case of the unmodified clay filled Viton B‐50 system. The results were explained with the help of thermodynamics, surface energies, and swelling studies. The difference in surface energy, Δγ, between the rubber and the unmodified clay was lower. The work of adhesion (67.63 mJ/m²) between Viton B‐50 and Cloisite NA+ was also higher than that (51.42 mJ/m²) between Viton B‐50 and Cloisite 20A. Negative ΔH_S value for the unmodified clay‐filled system thermodynamically favored the formation of the nanocomposite as compared to the modified clay filled samples where ΔH_S is positive or zero. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 162‐176, 2006     

Preparation and characterization of rigid poly(vinyl chloride)/MMT nanocomposites. II. XRD,morphological and mechanical characteristics

A Haake torque rheometer equipped with an internal mixer is used to study the influence of the amount of sodium montmorillonite (Na⁺‐MMT) and organically modified MMT (O‐MMT) on X‐ray diffraction (XRD), morphology, and mechanical characteristics of rigid poly (vinyl chloride) (PVC)/Na⁺‐MMT and PVC/O‐MMT nanocomposites, respectively. Results of XRD and transmission electron microscopy (TEM) indicate that MMT is partially encapsulated and intercalated in the rigid PVC/Na⁺‐MMT nanocomposites. However, results of XRD and TEM show MMT is partially intercalated and exfoliated in the rigid PVC/O‐MMT nanocomposites. Tensile strength, yield strength, and elongation at break of the rigid PVC/MMT nanocomposites were improved simultaneously with adding 1–3 wt % Na⁺‐MMT or O‐MMT with respect to that of pristine PVC. However, the addition of Na⁺‐MMT or O‐MMT should be kept as not more than 3 wt % to optimize the mechanical properties and the processing stability of the rigid PVC/MMT nanocomposites. SEM micrographs of the fractured surfaces of the rigid PVC/Na⁺‐MMT and PVC/O‐MMT nanocomposites both before and after tensile tests were also illustrated and compared. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2145–2154, 2006     

Methacrylate modified clays and their polystyrene and poly(methyl methacrylate) nanocomposites

Two methacrylate‐modified clays have been prepared and used to produce nanocomposites of polystyrene and poly(methyl methacrylate) by in situ polymerization. These nanocomposites have been characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), cone calorimetry and the evaluation of mechanical properties. When the clay contains only a single methacrylate unit, the styrene system is exfoliated but methacrylate is intercalated. When two methacrylate units are present on the cation of the clay, both systems are exfoliated. TGA data show that the thermal stability of all the nanocomposites is improved, as expected. The relationships between the fire properties and nanostructure of the nanocomposites are complicated, as shown by cone calorimetry. The conclusions that one may reach using cone calorimetry do not completely agree with those from XRD and TEM. The evaluation of mechanical properties shows an increase in Young's modulus for all nanocomposites along with a decrease in elongation; tensile strength is decreased for methacrylate nanocomposites but increased for styrenics systems. Copyright © 2004 John Wiley & Sons, Ltd.     

Impact of the clay organic modifier on the morphology of polymer–clay nanocomposites prepared by in situ free‐radical polymerization in emulsion

Poly(styrene‐co‐butyl acrylate) copolymers were prepared by free‐radical random copolymerization of styrene and butyl acrylate in emulsion in the presence of 10% of surface‐modified sodium montmorillonite (Na‐MMT). The objective of this work was to evaluate the impact of the clay organic modifier in terms of its chemical structure, its degree of interaction within the clay galleries surface, and its ability to copolymerize with monomers, on the morphology and properties of the final nanocomposite prepared. Na‐MMT was modified using different organic modifiers, namely: sodium 1‐allyloxy‐2‐hydroxypropyl (Cops), 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid (AMPS), N‐isopropylacrylamide (NIPA), and sodium 11‐methacryloyloxy‐undecan‐1‐yl sulfate (MET), respectively. The morphology and properties of the nanocomposites obtained were found to be dependant on the clay organic modifier. X‐ray diffraction (XRD) and transmission electron microscopy indicated that, nanocomposites at 10% clay loading with Cops‐, NIPA‐, and MET‐modified clays, yielded intercalated to partially exfoliated structures, whereas AMPS‐modified clay gave a nanocomposite with a fully exfoliated structure. All polymer–clay nanocomposites were found to be more thermally stable than neat poly(S‐co‐BA) as were determined by TGA. However, nanocomposites with intercalated structures exhibited greater thermal stability relative to fully exfoliated ones. Furthermore, nanocomposites with exfoliated structures exhibited higher storage moduli (G^I) than partially exfoliated once, whereas intercalated structure showed the lowest G^I values. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3619–3628, 2008     

Preparation and characterization of poly(ethyl acrylate)/bentonite nanocomposites by in situ emulsion polymerization

Transparent poly(ethyl acrylate) (PEA)/bentonite nanocomposites containing intercalated–exfoliated combinatory structures of clay were synthesized by in situ emulsion polymerizations in aqueous dispersions containing bentonite. The samples for characterization were prepared through direct‐forming films of the resulting emulsions without coagulation and separation. An examination with X‐ray diffraction and transmission electron microscopy showed that intercalated and exfoliated structures of clay coexisted in the PEA/bentonite nanocomposites. The measurements of mechanical properties showed that PEA properties were greatly improved, with the tensile strength and modulus increasing from 0.65 and 0.24 to 11.16 and 88.41 MPa, respectively. Dynamic mechanical analysis revealed a very marked improvement of the storage modulus above the glass‐transition temperature. In addition, because of the uniform dispersion of silicate layers in the PEA matrix, the barrier properties of the materials were dramatically improved. The permeability coefficient of water vapor decreased from 30.8 × 10^?6 to 8.3 × 10^?6 g cm/cm² s cmHg. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1706–1711, 2002     

Effect of the diisocyanate on the structure and properties of polyurethane acrylate prepolymers

In this study, we investigated the role of diisocyanate on the properties of polyurethane acrylate (PUA) prepolymers based on polypropylene oxide (M̄_n = 2000 g · mol⁻¹). The diisocyanates studied were isophorone diisocyanate, 4‐4′dicyclohexylmethane diisocyanate, and toluene diisocyanate (pure 2,4‐TDI, pure 2,6‐TDI, and a TDI mixture, TDI_tech). The molecular structure of the diisocyanate had a major role on the course of the polycondensation and, more precisely, on the sequence length distribution of the final prepolymer. Moreover, the structural organization of the prepolymer also strongly depended on the nature of the diisocyanate. Two types of behaviors were particularly emphasized. On the one hand, the PUA synthesized from 2,4‐TDI displayed an enhanced intermixing between soft polyether segments and hard urethane groups, as revealed by the analysis of hydrogen bonding in Fourier transform infrared. Consecutively, the glass transition shifted to higher temperatures for these polymers. On the other hand, strong hard–hard inter‐urethane associations were observed in 2,6‐TDI‐based prepolymers; these led to microphase segregation between polyether chains and urethane groups, as revealed by optical microscopy. This inhomogeneous structure was thought to be responsible for the unusual rheological behavior of these PUA prepolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2750–2768, 2000     

Preparation of Poly(ε‐caprolactone)/Clay Nanocomposites by Microwave‐Assisted In Situ Ring‐Opening Polymerization

PCL/clay nanocomposites were prepared by microwave‐assisted in situ ROP of ε‐caprolactone in the presence of either unmodified clay (Cloisite® Na⁺) or clay modified by quaternary ammonium cations containing hydroxyl groups (Cloisite 30B). This PCL showed significantly improved monomer conversion and molecular weight compared with that produced by conventional heating. An intercalated structure was observed for the PCL/Cloisite Na⁺ nanocomposites, while a predominantly exfoliated structure was observed for the PCL/Cloisite 30B nanocomposites. Microwave irradiation proved to be an effective and efficient method for the preparation of PCL/clay nanocomposites.

     

Thermotropic liquid crystalline polyester nanocomposites via in situ intercalation polycondensation

A thermotropic liquid crystalline polyester (TLCP)/organoclay nanocomposite was synthesized via in situ intercalation polycondensation of diethyl‐2,5‐dihexyloxyterephthalic acid and 4,4′‐biphenol in the presence of organically modified montmorillonite (MMT). The organoclay, C18‐MMT, was prepared by the ion exchange of Na⁺‐MMT with octadecylamine chloride (C18‐Cl^?). TLCP/C18‐MMT nanocomposites were prepared to examine the variations of the thermal properties, morphology, and liquid crystalline phases of the nanocomposites with clay content in the range of 0–7 wt%. It was found that the addition of only a small amount of organoclay was sufficient to improve the thermal behavior of the TLCP hybrids, with maximum enhancement being observed at 1 wt% C18‐MMT. Copyright © 2008 John Wiley & Sons, Ltd.     

Pendant cyclic carbonate‐polymer/Na‐smectite nanocomposites via in situ intercalative polymerization and solution intercalation

Nanocomposites of sodium smectite with polyether‐ and polystyrene‐containing pendant cyclic carbonates offer a novel approach to improving hydraulic barrier properties of Na‐smectite liners to saline leachates. The cyclic carbonate polyethers were prepared by cationic ring opening polymerization of a cyclic carbonate‐containing epoxide, whilst polystyrene polymers having pendant cyclic carbonate groups were obtained from radical photopolymerization of styrene. Na‐smectite nanocomposites of these polymers were formed via clay in situ polymerization and solution intercalation methods. X‐ray diffraction (XRD) and FT‐IR analysis confirmed that the polyether can be intercalated within the layers of smectite via in situ as well as solution intercalation of the pre‐formed polymer. The cyclic carbonate polyether nanocomposite was more resistant to leaching in 3M aqueous sodium chloride than its respective cyclic carbonate. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2421–2429     

Thermal and mechanical properties of syndiotactic polystyrene/organoclay nanocomposites with different microstructures

The fabrication of syndiotactic polystyrene (sPS)/organoclay nanocomposite was conducted via a stepwise mixing process with poly(styrene‐co‐vinyloxazolin) (OPS), that is, melt intercalation of OPS into organoclay followed by blending with sPS. The microstructure of nanocomposite mainly depended on the arrangement type of the organic modifier in clay gallery. When organoclays that have a lateral bilayer arrangement were used, an exfoliated structure was obtained, whereas an intercalated structure was obtained when organoclay with a paraffinic monolayer arrangement were used. The thermal and mechanical properties of sPS nanocomposites were investigated in relation to their microstructures. From the thermograms of nonisothermal crystallization and melting, nanocomposites exhibited an enhanced overall crystallization rate but had less reduced crystallinity than a matrix polymer. Clay layers dispersed in a matrix polymer may serve as a nucleating agent and hinder the crystal growth of polymer chains. As a comparison of the two nanocomposites with different microstructures, because of the high degree of dispersion of its clay layer the exfoliated nanocomposite exhibited a faster crystallization rate and a lower degree of crystallinity than the intercalated one. Nanocomposites exhibited higher mechanical properties, such as strength and stiffness, than the matrix polymer as observed in the dynamic mechanical analysis and tensile tests. Exfoliated nanocomposites showed more enhanced mechanical properties than intercalated ones because of the uniformly dispersed clay layers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1685–1693, 2004     

Effects of organic modifications of clay on the ultraviolet‐curing behavior and structure of a polyester‐acrylate/clay nanocomposite system

A pristine clay (Na⁺‐montmorillonite (MMT) and three different organoclays (20A‐MMT, vinylbenzyl dimethyldodecyl ammonium (VDA)‐MMT, and siloxane diamine ammonium (SDA)‐MMT) that originated from the pristine clay were used to prepare polyester‐acrylate (PEA)/clay nanocomposites by in situ ultraviolet (UV)‐curing. Except for the commercial organoclay (20A‐MMT), VDA‐MMT, and SDA‐MMT were prepared in this study by ion exchange method. The effects of organic modifications of the pristine clay on the UV‐curing behavior and structure of the nanocomposite system were investigated. The organic modifications of the clay affected considerably the UV‐curing behavior and structure of the nanocomposite system. Copyright © 2008 John Wiley & Sons, Ltd.     

Review of melt‐processed nanocomposites based on EVOH/organoclay

EVOH nanocomposites containing organically treated clays are unique systems in which the clay is strongly attracted to EVOH, thus affecting the morphology and the resultant thermal and mechanical properties. A strong effect of the processing conditions on morphology, thermal, and mechanical properties was observed. In highly interacting systems, under dynamic mixing conditions, in addition to a fracturing process of the clay particles, an onion‐like delamination process is suggested. EVA‐g‐MA and LLDPE‐g‐MA, having polar groups, were studied as compatibilizers to further induce clay intercalation and exfoliation. The compatibilizers affected both the thermal and mechanical properties of the composites at different levels. Thermal analysis showed that with increasing compatibilizer content lower crystallinity levels result, until at a certain content no crystallization has taken place. A Ny‐6 (nylon‐6)/EVOH blend is an interesting host matrix for incorporation of low organoclay contents. The Ny‐6/EVOH blend is a unique system that tends to hydrogen bond and also to in situ chemically react during melt mixing. The addition of clay seems to interrupt the chemical reaction between the two host polymers at certain compositions, leading to lower melt blending torque levels when clay is present. A competition between Ny‐6 and EVOH regarding the intercalation process takes place. However, Ny‐6 seems to lead to exfoliated structures, whereas EVOH forms intercalated structures, as revealed from combined XRD and TEM experiments, owing to thermodynamic considerations and preferential localization of the clay in Ny‐6. Of special interest is the increased storage modulus seen by the presence of only 1 wt % clay, which was achieved by extrusion under high shear forces, leading to a completely exfoliated structure. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1931–1943, 2005     

Vibrational energy-harvesting performance of bio-sourced flexible polyamide 11/layered silicate nanocomposite films

The energy-harvesting efficiency of melt processed polyamide 11 (PA11) films and its nanocomposites have been investigated as a function of filler type and content. In the present work, nanoclays have been used as structural modifiers in a PA11 matrix. The nanocomposites were prepared using layered clays, Cloisite 20A, 10A, and Na⁺, by extrusion process through varying the filler content, 1, 2, 4, and 5?wt.%. The crystalline structure of these nanocomposites has been studied by X-ray diffractometer. It has been demonstrated that layered silicates are not significant for the structural quality of the obtained nanocomposites. Regarding the interlayer peak of different clays, it has also been revealed that Cloisite 20A is partially exfoliated, whereas 10A and Na⁺ are totally exfoliated in the PA11 matrix. From mechanical and dynamic mechanical analyses, it was found that the addition of layered silicates results in an increase in mechanical properties. The piezoelectric strain coefficient d₃₃ and dielectric constant ε_R have been measured on polarized films at ambient temperature. Among all the prepared nanocomposites only Cloisite Na⁺-loaded PA11 nanocomposites showed the best piezoelectric constant. This observation showed that piezoelectric constant not only depends on the crystalline phases but also on the nature of the filler. Cloisite Na⁺ is more polar than other modified clays and high polarity leads to a better polarization response. A specific method for the quantification of energy vibration recovery has been developed for these nanocomposites. The capabilities of vibrational energy recovery were studied on PA11 loaded with Cloisite Na⁺.     

Synthesis and characterization of organosoluble,thermoplastic elastomer/clay nanocomposites

We synthesized organosoluble, thermoplastic elastomer/clay nanocomposites by making a jelly like solution of ethylene vinyl acetate containing 28% vinyl acetate (EVA‐28) and blending it with organomodified montmorillonite. Sodium montmorillonite (Na⁺‐MMT) was made organophilic by the intercalation of dodecyl ammonium ions. X‐ray diffraction patterns of Na⁺‐MMT and its corresponding organomodified dodecyl ammonium ion intercalated montmorillonite (12Me‐MMT) showed an increase in the interlayer spacing from 11.94 to 15.78 Å. However, X‐ray diffraction patterns of the thermoplastic elastomer and its hybrids with organomodified clay contents up to 6 wt % exhibited the disappearance of basal reflection peaks within an angle range of 3–10°, supporting the formation of a delaminated configuration. A hybrid containing 8 wt % 12Me‐MMT revealed a small hump within an angle range of 5–6° because of the aggregation of silicate layers in the EVA‐28 matrix. A transmission electron microscopy image of the same hybrid showed 3–5‐nm 12Me‐MMT particles dispersed in the thermoplastic elastomer matrix; that is, it led to the formation of nanocomposites or molecular‐level composites with a delaminated configuration. The formation of nanocomposites was reflected through the unexpected improvement of thermal and mechanical properties; for example, the tensile strength of a nanocomposite containing only 4 wt % organophilic clay was doubled in comparison with that of pure EVA‐28, and the thermal stability of the same nanocomposite was higher by about 34 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2065–2072, 2002