Voltammetric investigation of hair dye constituents: application to the quantification of p-phenylenediamine.

The application of electrochemical techniques to the determination of common hair dye constituents was investigated. Cyclic voltammetry was used to probe the electrode response to p-phenylenediamine (PPD), 4-chlororesorcinol and m-aminophenol with square wave voltammetry used to effect quantitative measurements. The nature of the electrode response was characterised and issues of surface fouling resulting from the deposition of electrogenerated reaction products were addressed. A procedure designed to allow the facile determination of PPD in hair care products is presented.     

Poly(2,2′-(1,4-phenylenedivinylene) Bis-8-hydroxyquinaldine) Modified Glassy Carbon Electrode for the Simultaneous Determination of Paracetamol and p-Aminophenol

A novel assay is reported for the simultaneous determination of paracetamol and p-aminophenol using a poly(2,2′-(1,4-phenylenedivinylene)bis-8-hydroxyquinaldine) modified glassy carbon electrode. Poly(2,2′-(1,4-phenylenedivinylene)bis-8-hydroxyquinoline) modified electrodes were prepared by electrochemical polymerization. The electrode surface was characterized by scanning electron microscopy. The electrochemical behavior of the modified electrode was investigated by cyclic voltammetry, square wave voltammetry, and electrochemical impedance spectroscopy. The anodic peak potentials for paracetamol and p-aminophenol were at 580 and 337 millivolts, respectively, with a separation of 243 millivolts, adequate for their simultaneous determination. The results showed that the linear dynamic ranges for paracetamol and p-aminophenol were 0.5–200 micromolar and 3–150 micromolars, whereas the limits of detection were 0.075 and 0.45 micromolar, respectively. The novel poly(2,2′-(1,4-phenylenedivinylene)bis-8-hydroxyquinaldine) modified electrode provided excellent selectivity, sensitivity, and stability and was employed for the determination of paracetamol and p-aminophenol in pharmaceutical products and urine.     

Quantitative Analysis of Irbesartan in Pharmaceuticals and Human Biological Fluids by Voltammetry

Abstract

A differential pulse (DP) and square wave (SW) voltammetric techniques were developed for the determination of irbesartan. The electrochemical behavior of irbesartan was investigated by cyclic voltammetry (CV), differential pulse voltammetry (DPV), and square wave voltammetry (SWV) at the hanging mercury drop electrode (HMDE). Different parameters were tested to optimize the conditions of the determination. It was found that in the range of 8 × 10^?6–1 × 10^?4 M, the currents measured by both of methods presented a good linear property as a function of the concentration of irbesartan. In addition, validation parameters, such as reproducibility, sensitivity, and recovery were evaluated as well. The slope of the log Ip- log ν linear plot was 0.58 indicating the diffusion control for 0.5 M sulphuric acid without the need for separation or complex sample preparation, since there was no interference from the excipients and endogenous substances.

The methods were successfully applied to the analysis of irbesartan in the pharmaceutical tablet formulations and in human serum samples.     

A Graphite‐Polyurethane Composite Electrode for the Analysis of Furosemide

A graphite‐polyurethane composite electrode has been used for the determination of furosemide, a antihypertensive drug, in pharmaceutical samples by anodic oxidation. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the electrooxidation process at +1.0 V vs. SCE over a wide pH range, with the result that no adsorption of analyte or products occurs, unlike at other carbon‐based electrode materials. Quantification was carried out using cyclic voltammetry, differential pulse voltammetry, and square‐wave voltammetry. Linear ranges were determined (up to 21 μmol L^?1 with cyclic voltammetry) as well as limits of detection (0.15 μmol L^?1 by differential pulse voltammetry). Four different types of commercial samples were successfully analyzed. Recovery tests were performed which agreed with those obtained by spectrophotometric evaluation. The advantages of this electrode material for repetitive analyzes, due to the fact that no electrode surface renewal is needed owing to the lack of adsorption, are highlighted.     

基于纳米结构的电化学传感器用于伏安法测定苄丝肼、尿酸和叶酸(英文)

A carbon paste electrode modified with carbon nanotubes and ferrocene was fabricated.An electrochemical study of the modified electrode and an investigation into its efficiency for the electrocatalytic oxidation of benserazide,uric acid and folic acid were undertaken.The electrode was also used to study the electrocatalytic oxidation of benserazide using cyclic voltammetry,chronoamperometry,and square wave voltammetry(SWV).We found that the oxidation of benserazide at the surface of the modified electrode occurs at a potential about 285 mV lower than that of unmodified carbon paste electrode.SWV gave a linear dynamic range from 8.0×10-7 to 7.0×10 4 mol/L.The detection limit was 1.0×10-7 mol/L for benserazide.This modified electrode was used for the determination of benserazide,uric acid,and folic acid in an urine sample.     

Antibiotic Detection in Urine Using Electrochemical Sensors Based on Vertically Aligned Carbon Nanotubes

A sensitive way to determine levofloxacin using a sensor based on vertical aligned carbon nanotubes is described. The morphology and the electrochemical performance of the electrodes were characterised by atomic force microscopy, cyclic voltammetry and square wave voltammetry. A scan‐rate study and electrochemical impedance spectroscopy showed that the levofloxacin oxidation product is adsorbed on the electrode surface. Differential pulse voltammetry in phosphate‐buffer solution allowed the development of a method to determine levofloxacin levels in the range of 1.0–10.0 µmol L^?1, with a detection limit of 75.2 nmol L^?1. The proposed sensor was successfully applied in the determination of levofloxacin in urine, and the obtained results were in full agreement with those from the HPLC procedure.     

Electrochemical Oxidation of Berberine and of Its Oxidation Products at a Glassy Carbon Electrode

The electrochemical behavior of berberine, an isoquinoline plant alkaloid with a wide spectrum of physiological effects, was studied at a glassy carbon electrode using cyclic, differential pulse and square‐wave voltammetry. The oxidation of berberine is a quasireversible, diffusion‐controlled process and occurred in a cascade mechanism with the formation of several oxidation products. The diffusion coefficient of berberine was calculated from cyclic voltammetry studies to be D=1.69×10^?6 cm² s^?1. The oxidation process of berberine is also pH dependent and the number of electrons and protons transferred was determined using differential pulse voltammetry. The formation of several oxidation products that adsorbed at the glassy carbon electrode surface was observed and their electrochemical behavior characterized. A mechanism for the oxidation of berberine at a glassy carbon electrode was proposed.     

Pulse Voltammetric Determination of Thiazolidine-4-Carboxylic Acids

Abstract

The electrochemical behaviour of thiazolidine-4-carboxylic acid (thioproline, Thz) and its derivatives 2-propyl-thiazolidine-4-carboxylic acid (PrThz) and 2-tetrahydroxybutyl-thiazolidine-4-carboxylic acid (AThz) has been studied by cyclic, normal and reverse pulse, differential pulse and Osteryoung square wave voltam-metrics. Anodic waves, resulting from the formation of adsorbed mercury thiazolidates, were obtained for all the compounds at mercury electrodes in acetate and phosphate buffers at pH from 3.8 to 8. the initially formed mercury compounds rapidly transform into the final products accumulating on the electrode surface. the oxidation products inhibit the anodic processes and distorted voltammetric curves were obtained at the covered electrodes. Various effects of these processes in various pulse voltammetric techniques were evident. Normal pulse voltammograms were least affected by the product transformations. Osteryoung square wave voltammetry permitted very fast determinations of Thz derivatives.     

农药噻嗪酮在玻碳电极上的电化学行为

应用循环伏安法(CV)、线性扫描伏安法(LSV)、微分脉冲伏安法(DPV)和方波伏安法(SWV)等研究了噻嗪酮在玻碳电极上的电化学行为,并建立样品噻嗪酮的SWV测定法.噻嗪酮在玻碳电极上的电还原涉及两质子/两电子和两质子的不可逆过程.     

基于纳米银/碳纳米纤维复合材料的增强效应电化学测定多贝斯

将银纳米粒子(AgNPs)电沉积在碳纳米纤维(CNFs)修饰玻碳电极表面制备纳米银/碳纳米纤维修饰玻碳电极(AgNPs/CNFs/GCE)。采用扫描电镜考察其表面形态,在K3[Fe(CN)6]-K4[Fe(CN)6]体系中用循环伏安法和电化学阻抗法研究AgNPs/CNFs/GCE的电化学行为。采用循环伏安法和方波伏安法研究多贝斯在AgNPs/CNFs/GCE上的电化学行为,结果表明,AgNPs/CNFs/GCE对多贝斯有显著的电催化作用。在方波伏安曲线上,多贝斯的还原峰电流与其浓度在1.0×10^-9~6.0×10^-6mol/L范围内成线性关系,检出限为0.50 nmol/L。AgNPs/CNFs/GCE的重现性和稳定性较好,可用于胶囊中多贝斯含量的测定。     

Electrochemical Determination of Citalopram by Adsorptive Stripping Voltammetry–Determination in Pharmaceutical Products

Abstract

The electrochemical behavior of citalopram was studied by square‐wave and square‐wave adsorptive‐stripping voltammetry (SWAdSV). Citalopram can be reduced and accumulated at a mercury drop electrode, with a maximum peak current intensity being obtained at a potential of approximately ?1.25 V vs. AgCl/Ag, in an aqueous electrolyte solution of pH 12. A SWAdSV method has been developed for the determination of citalopram in pharmaceutical preparations. The method shows a linear range between 1.0×10^?7 and 2.0×10^?6 mol L^?1 with a limit of detection of 5×10^?8 mol L^?1 for an accumulation time of 30 s. The precision of the method was evaluated by assessing the repeatability and intermediate precision, achieving good relative standard deviations in all cases (≤2.3%). The proposed method was applied to the determination of citalopram in five pharmaceutical products and the results obtained are in good agreement with the labeled values.     

A new voltammetric sensor for the determination of sulfite in water and wastewater using modified-multiwall carbon nanotubes paste electrode

The electrochemical response of a modified-carbon nanotubes paste electrode with p-aminophenol was investigated as an electrochemical sensor for sulfite determination. The electrochemical behaviour of sulfite was studied at the surface of the modified electrode in aqueous media using cyclic voltammetry and square wave voltammetry. It has been found that under the optimum condition (pH 7.0) in cyclic voltammetry, the oxidation of sulfite occurs at a potential about 680?mV less positive than that of an unmodified-carbon nanotubes paste electrode. Under the optimized conditions, the electrocatalytic peak current showed linear relationship with sulfite concentration in the range of 2.0?×?10^?7–2.8?×?10^?4?mol?L^?1 with a detection limit of 9.0?×?10^?8?mol?L^?1 sulfite. The relative standard deviations for ten successive assays of 1.0 and 50.0?µmol?L^?1 sulfite were 2.5% and 2.1%, respectively. Finally, the modified electrode was examined as a selective, simple and precise new electrochemical sensor for the determination of sulfite in water and wastewater samples.     

Voltammetric Determination of Dye-Uptake for C. I. Acid Blue 120 Dyeing Silk

Abstract

The electrochemical behavior of Colour Index Acid Blue 120 at carbon paste electrode is studied with cyclic voltammetry and square wave voltammetry for the first time. Two irreversible oxidative peaks at 0.61 V (P_a,1) and 0.90 V(P_a,2) (both vs. SCE) are found at a scan rate of 0.1 V/s. Their electrode processes are both adsorption-controlled with two electrons and two protons participating. The peak currents of the P_a,1 are proportional to the concentration of Colour Index Acid Blue 120 in the range of 2.08–20.80 µM and 62.4–520.0 µM. The coexisting substances such as inorganic ions and fatty alcohol polyoxyethylene ether do not interfere with the determination. The method is applied to the determination of dye-uptake for Colour Index Acid Blue 120 dyeing silk. The results are in good agreement with the spectrophotometric method.     

Electrochemical Behavior of 8‐Azaguanine at DNA Langmuir–Blodgett Modified Glassy Carbon Electrode and Its Analytical Application

A highly sensitive electrochemical biosensor for the detection of trace amounts of 8‐azaguanine has been designed. Double stranded (ds)DNA molecules are immobilized onto a glassy carbon electrode surface with Langmuir–Blodgett technique. The adsorptive voltammetric behaviors of 8‐azaguanine at DNA‐modified electrode were explored by means of cyclic voltammetry and square wave voltammetry. Compared with bare glassy carbon electrode (GCE), the Langmuir–Blodgett film modified electrode can greatly improve the measuring sensitivity of 8‐azaguanine. Under the optimum experimental conditions, the Langmuir–Blodgett film modified electrode in pH 3.0 Britton–Robinson buffer solutions shows a linear voltammetric response in the range of 5.0×10^?8 to 1.0×10^?5 mol L^?1 with detection limit 9.0×10^?9 mol L^?1. The method proposed was applied successfully for the determination of 8‐azaguanine in diluted human urine with wonderful satisfactory.     

Voltammetric determination of herbicide molinate in river water and rice samples using solid silver amalgam electrode fabricated with nanoparticles

The evaluation of the voltammetric behaviour and the determination of herbicide molinate were performed for the first time over the surface of solid amalgam electrode fabricated with silver nanoparticles using cyclic voltammetry and square-wave voltammetry techniques. The experimental and instrumental parameters were evaluated to reach the maximum analytical response for molinate. It was achieved when a medium composed of 0.04 mol L^?1 Britton–Robinson buffer at the pH value of 4.0 was used. Under these conditions, molinate showed one pronounced reduction peak at E_p = ?0.37 V (vs. Ag/AgCl 3 mol L^?1) that was characterised as an irreversible system. An analytical curve was constructed at the concentration range from 9.36 to 243.49 µg L^?1 and a limit of detection of 2.34 µg L^?1 was obtained. The amalgam electrode presented good stability during the measurements with relative standard deviation (RSD) values of 2.9% for the repeatability and 5.4% for the reproducibility. The voltammetric method developed here could be conveniently applied for the determination of molinate in river water and rice spiked samples at levels below those established on the legislations of European Union and Brazil with good accuracy (RSD of less than 5% for all samples). Comparison with HPLC technique was carried out and the results indicated satisfactory concordance. According to the results depicted here, the silver nanoparticles solid amalgam electrode showed itself highly sensitive and an interesting alternative for the routine analysis of molinate in water and food samples. Furthermore, it introduces an environmentally acceptable alternative to the mercury electrodes, most commonly used for determination of reducible pesticides.     

Electroanalytical Determination of Cd(II) and Pb(II) in Bivalve Mollusks using Electrochemically Reduced Graphene Oxide‐based Electrode

An electrochemical sensor for the simultaneous determination of Cd(II) and Pb(II) by square wave anodic stripping voltammetry (SWASV) in bivalve mollusks using a glassy carbon electrode modified with electrochemically reduced graphene oxide has been developed. The modified surface was characterized by cyclic voltammetry, high resolution scanning electron microscopy (HR‐SEM), and Raman spectroscopy. The optimum conditions were optimized and a linear range was observed from 15–105 μg L^?1 with a limits of detection of 15 μg L^?1 for Cd(II) and Pb(II). The methodology was validated and applied in different samples of commercial bivalve mollusks with satisfactory results. The high conductivity and greater surface area of the modifying agent improves the preconcentration capacity of the electrochemical sensor, allowing to develop a simple, rapid and sensitive analysis in the detection of lead and cadmium in marine resources.     

Analytical Potentialities of Carbon Nanotube/Silicone Rubber Composite Electrodes: Determination of Propranolol

A new composite electrode based on multiwall carbon nanotubes (MWCNT) and silicone‐rubber (SR) was developed and applied to the determination of propranolol in pharmaceutical formulations. The effect of using MWCNT/graphite mixtures in different proportions was also investigated. Cyclic voltammetry and electrochemical impedance spectroscopy were used for electrochemical characterization of different electrode compositions. Propranolol was determined using MWCNT/SR 70 % (m/m) electrodes with linear dynamic ranges up to 7.0 µmol L^?1 by differential pulse and up to 5.4 µmol L^?1 by square wave voltammetry, with LODs of 0.12 and 0.078 µmol L^?1, respectively. Analysis of commercial samples agreed with that obtained by the official spectrophotometric method. The electrode is mechanically robust and presented reproducible results and a long useful life.     

Carbon paste electrode modified by cobalt ions dispersed into poly (N-methylaniline) preparing in the presence of SDS: application in electrocatalytic oxidation of hydrogen peroxide

Conducting and stable poly (N-methylaniline) film was prepared by using the repeated potential cycling technique in aqueous solution containing N-methylaniline, sulfuric acid, and sodium dodecyl sulfate (SDS) at the surface of carbon paste electrode (CPE). The transition metal ions of Co(ІІ) were incorporated to the polymer by immersion of the modified electrode in 0.1 M cobalt chloride solution for 10 min. The electrochemical characterization of this modified electrode exhibits stable redox behavior of Co(ІІ)→Co(ІІІ) and formation of insoluble oxide/hydroxide cobalt species on the CPE surface. The modified electrode showed well-defined and stable redox couples in alkaline aqueous solution. The modified electrode showed excellent electrocatalytic activity for oxidation of hydrogen peroxide. The response of modified electrode toward the H₂O₂ oxidation was examined using cyclic voltammetry, differential pulse voltammetry, square wave voltammetry, and chronoamperometry. This modified electrode has many advantages such as simple preparation procedure, good reproducibility, and high catalytic activity toward the hydrogen peroxide oxidation. Such characteristics were explored for the specific determination of hydrogen peroxide in cosmetics product sample, giving results in excellent agreement with those obtained by standard method.     

Electrochemical Determination and in silico Studies of Fludarabine on NH2 Functionalized Multiwalled Carbon Nanotube Modified Glassy Carbon Electrode

A sensitive voltammetric technique has been developed for the determination of Fludarabine using amine‐functionalized multi walled carbon nanotubes modified glassy carbon electrode (NH₂‐MWCNTs/GCE). Molecular dynamics simulations, an in silico technique, were employed to examine the properties including chemical differences of Fludarabine‐ functionalized MWCNT complexes. The redox behavior of Fludarabine was examined by cyclic, differential pulse and square wave voltammetry in a wide pH range. Cyclic voltammetric investigations emphasized that Fludarabine is irreversibly oxidized at the NH₂‐MWCNTs/GCE. The electrochemical behavior of Fludarabine was also studied by cyclic voltammetry to evaluate both the kinetic (k_s and E_a) and thermodynamic (ΔH, ΔG and ΔS) parameters on NH₂‐MWCNTs/GCE at several temperatures. The mixed diffusion‐adsorption controlled electrochemical oxidation of Fludarabine revealed by studies at different scan rates. The experimental parameters, such as pulse amplitude, frequency, deposition potential optimized for square‐wave voltammetry. Under optimum conditions in phosphate buffer (pH 2.0), a linear calibration curve was obtained in the range of 2×10^?7 M–4×10^?6 M solution using adsorptive stripping square wave voltammetry. The limit of detection and limit of quantification were calculated 2.9×10^?8 M and 9.68×10^?8 M, respectively. The developed method was applied to the simple and rapid determination of Fludarabine from pharmaceutical formulations.     

Electrochemical characterization of a superoxide biosensor based on the co-immobilization of cytochrome c and XOD on SAM-modified gold electrodes and application to garlic samples

This paper describes the characterization and optimization of an amperometric cytochrome c (cyt c)-based sensor for the determination of the antioxidant capacity of pure substances and natural samples. The cyt c and the xanthine oxidase (XOD) enzyme were co-immobilized on the electrode using the combination of several long-chain thiols. The self-assembled monolayer (SAM) was optimized in terms of composition and ratio between thiols. The immobilization protocol for both cyt c and XOD and the SAM formation time were evaluated through electrochemical methods, such as cyclic voltammetry (CV), square wave voltammetry (SWV), chronoamperometry (CA) and impedance spectroscopy (IS). Finally, the biosensor was applied to the determination of the antioxidant capacity of pure alliin and two compounds extracted from garlic bulbs.