单色光在损耗介质中激励的受激布里渊散射

研究了单色光在损耗介质中激励的受激布里渊散射，运用分布起伏噪声源模型描述了受激布里渊散射的产生过程，通过傅里叶变换，得到了输出斯托克斯光波的功率谱密度。     

Measurement of stimulated Brillouin scattering （SBS） threshold based on waveform variation of SBS optical limiting

This paper proposes a method for measuring the stimulated Brillouin scattering (SBS) threshold based on waveform variation of SBS optical limiting. The output waveforms for different pump power densities are numerically simulated, and validated in the Nd:YAG seed-injected laser system. The results indicate that SBS does not take place in the case of a low pump power density and thus the output power scales up linearly with pump power. Once the pump power density exceeds the SBS threshold, SBS takes place and thereby the energies are transferred from pump to Stokes. As a result, a small shoulder appears in the trailing edge of the output waveform, which provides another method to determine the SBS threshold.     

Stimulated Brillouin Scattering Enhancement Factor Improvement in a 11.6-GHz-Linewidth 1.5-kW Yb-Doped Fiber Amplifier

The stimulated Brillouin scattering(SBS) threshold enhancement factor in a pure white noise linewidth broadening Yb-doped fiber amplifier(YDFA) with a short large mode area fiber is theoretically and experimentally studied.We demonstrate a 1064.08 nm,11.6 GHz linewidth,1.5kW output power YDFA with an SBS threshold enhancement of ~57(26 W SBS threshold with single frequency seed).The output beam is near-diffraction limited with a beam quality factor of M~2 = 1.15 and a slope efficiency of up to 87%.No SBS or stimulated Raman scattering effects are observed in the whole power range.Further power scaling is limited by the available pump power in our system.     

Numerical analysis of stimulated Brillouin scattering in high-power double-clad fiber lasers

A theoretical analysis of stimulated Brillouin scattering (SBS) in linear cavity Yb³⁺-doped double-clad fiber lasers is presented by solving the steady-state rate equations with the SBS. The effects of cavity length, fiber core diameter, input mirror reflectivity at Stokes wavelength, Yb³⁺ concentration and laser linewidth on the SBS are discussed. Numerical results show that the SBS threshold power can be improved by shortening the cavity length, using large mode area fiber, reducing the input mirror reflectivity at Stokes wavelength, lowering the Yb³⁺ concentration and broadening the laser linewidth, and the influence of the laser linewidth on the SBS threshold power is more noticeable than other system parameters.     

Statistical properties of stimulated Brillouin scattering in single-mode optical fibers above threshold

We performed numerical simulations to obtain statistical and spectral characteristics of stimulated Brillouin scattering (SBS) initiated by Gaussian noise in single-mode optical fibers. Recently published experimental spectra of SBS power [e.g., Phys. Rev. Lett. 85, 1879 (2000)] are explained completely by a one-dimensional SBS model. We give a clear physical insight into the problem and, for what is to our knowledge the first time, reveal how the probability function of Stokes power, the power-correlation function, and the SBS spectra evolve as key parameters of the model vary, leading to a modification of Stokes field statistics.     

Investigation on the output energy characteristic of optical limiting based on stimulated Brillouin scattering

Stimulated Brillouin scattering (SBS) featuring sub-nanosecond response time takes place at a high power threshold, which enables its application at a high power density. When the intensity of input light excesses the SBS threshold, strong SBS process takes place through SBS medium, leading to a quick energy transfer from pump to the Stokes and thereby an optical limiting characteristic in the output energy. In this paper, the correlation between SBS output energy and input power density is numerically simulated and validated in the Nd: YAG Q-switch laser system. The results indicate that not only the output energy exhibits an optical limiting characteristic, but also the clamped value of output energy can be controlled by changing the medium or the focal length.     

S波段光纤拉曼放大器中级联受激布里渊散射串扰的实验研究

研究了光纤激光器前向抽运的S波段分布式光纤拉曼放大器中级联的受激布里渊散射(SBS)串扰现象。用窄光谱带宽(<100MHz)的可调谐激光二极管作为信号源,通过S波段分布式光纤拉曼放大器,当被放大的信号功率超过单模光纤受激布里渊散射的阈值时,出现了前向受激布里渊散射,这是传导声波布里渊散射在光纤放大器中放大的现象。随着拉曼放大器抽运功率的提高,在斯托克斯区,出现了两阶受激布里渊散射线,在实验中观测到偶数阶的受激布里渊散射谱线功率大于奇数阶的布里渊一瑞利散射线。当进一步增加拉曼放大器的抽运功率,出现了前向级联的多阶受激布里渊散射现象,拉曼放大器的增益下降,被放大的信号功率转换为受激布里渊散射,噪声变大。受激布里渊散射的串扰破坏了拉曼放大器的特性,使拉曼放大器无法在密集波分复用光纤传输系统中使用,因此需要严格地控制入纤的信号功率和放大器的抽运功率。在实验中还观测到在光纤拉曼放大器中被放大的信号光和受激布里渊散射线两侧的伴线。     

Power dependence of Brillouin linewidths in a silica fiber

We report the dependence of Brillouin linewidths on the pump power below the threshold of Brillouin lasing in a silica fiber. The Stokes Brillouin shift in a silica fiber is nearly unchanged, and its linewidth decreases with increasing pump power. However, the anti-Stokes Brillouin shift becomes smaller and its linewidth larger with increasing pump power. We explain these experimental results by the distributed fluctuating source model.     

A 168-W high-power single-frequency amplifier in an all-fiber configuration

We present a high-power,single-frequency,narrow linewidth fiber amplifier based on master oscillator power amplification chains in an all-fiber configuration.The effect of the delivery fiber on the maximum output power is studied.A home-made 1064-nm seed laser with a 20-kHz linewidth is boosted to 129 W,and limited by stimulated Brillouin scattering(SBS) when the delivery fiber is 1.2 m long.By shortening the delivery fiber length to 0.7 m,the SBS threshold is increased efficiently and the maximum output power rises to 168 W with an 82.9% power conversion efficiency.The experimental results indicate that the output power can be further raised by shortening the delivery fiber length and increasing the pump power.     

Dynamics of Stimulated Brillouin Scattering in a Short and High-Finesse Fiber Fabry-Perot Resonator

We theoretically investigate the dynamics of stimulated Brillouin scattering (SBS) in a short fiber Fabry-Perot resonator with reflection mirrors. The analysis is based on the coherent six-wave model including an optical Kerr effect and the linear cavity detunings for the pump and created Stokes waves are taken into account in the formulation. The instabilities including periodic, quasi-periodic and chaotic oscillations can occur owing to the Kerr effect even if the fiber resonator is so short as to ensure a single longitudinal-mode operation. The threshold power for SBS and the boundary power between the stable and unstable regions are numerically calculated as a function of the amplitude reflectance of mirrors for different cavity detunings. The dynamics of SBS and these two critical powers depend on the amplitude reflectance and the cavity detuning. Although an increase in the mirror reflectance decreases the threshold power for SBS, it may limit the utility of SBS since the stable region is narrow and the output power levels of the pump and Stokes waves are low.     

A 168-W high-power single-frequency amplifier in an all-fiber configuration

We present a high-power, single-frequency, narrow linewidth fiber amplifier based on master oscillator power amplification chains in an all-fiber configuration. The effect of the delivery fiber on the maximum output power is studied. A home-made 1064-nm seed laser with a 20-kHz linewidth is boosted to 129 W, and limited by stimulated Brillouin scattering (SBS) when the delivery fiber is 1.2 m long. By shortening the delivery fiber length to 0.7 m, the SBS threshold is increased efficiently and the maximum output power rises to 168 W with an 82.9% power conversion efficiency. The experimental results indicate that the output power can be further raised by shortening the delivery fiber length and increasing the pump power.     

窄线宽纳秒脉冲光纤拉曼放大器的理论模型和数值分析

窄线宽纳秒脉冲光纤拉曼放大器在非线性频率变换、遥感探测和量子信息等领域有广泛的应用前景.综合考虑受激拉曼散射(stimulated Raman scattering,SRS)、受激布里渊散射(stimulated Brillouin scattering,SBS)、自相位调制(self-phase modulation)和交叉相位调制(cross-phase modulation)等非线性效应,建立了窄线宽纳秒脉冲光纤拉曼放大器的非线性动力学模型.仿真分析了放大器中脉冲激光的时频演化特性,对比研究了抽运脉冲宽度、光纤长度和信号光功率等因素对放大器性能的影响.研究发现,上述因素会影响放大器的SRS阈值、SBS阈值、输出激光线宽、激光转换效率等.例如,当脉冲宽度为800 ns时,SBS随着抽运功率的增加而发生,限制了激光功率的提升;减短抽运脉宽可以抑制SBS,但是输出激光的线宽易于展宽到数百MHz以上;增加光纤长度可以获得更低的SRS阈值和更高的转换效率,但是SBS效应和光谱展宽程度也随之增强.系统搭建中需要平衡各非线性效应,选择合适的系统参数.研究内容可以为窄线宽纳秒脉冲光纤拉曼放大器的设计搭建提供参考.     

Investigation on threshold power of stimulated Brillouin scattering in photonic crystal fiber

We have developed a theoretical approach to simulate stimulated Brillouin scattering (SBS) generation in photonic crystal fiber (PCF). The threshold condition for the SBS occurrence has been derived as a function of fiber parameters and input pump power. A particular emphasis is given to the influence of the input pump power and fiber length on the Brillouin gain in the PCF. To assess threshold pump power accurately, the pump depletion effect has been included by employing the 1% criterion. This simulation can anticipate the Brillouin threshold gain value precisely. The threshold gain varies from 14 to 18 depending on the PCF length.     

Cavity enhanced stimulated Brillouin scattering in an optical chip for multiorder Stokes generation

We report the first demonstration of on-chip cascaded stimulated Brillouin scattering (SBS). Cascaded SBS is characterized in a 4 cm long chalcogenide (As?S?) rib waveguide where the end facet reflections provide a monolithic Fabry-Perot (FP) resonator. The presence of the FP cavity reduces the Brillouin gain threshold, which enables observation of cascaded SBS at reduced pump powers. We observe up to three orders of Stokes waves in the backscattered signal at a coupled peak power of 1.34 W. Anti-Stokes waves due to four-wave mixing between the pump and the Stokes wave were observed in the forward spectrum.     

窄线宽脉冲光纤激光的自相位调制预补偿研究

自相位调制(SPM)效应会展宽窄线宽脉冲光纤激光的光谱宽度,降低其相干性.通过相位调制对SPM引起的非线性相移进行预补偿,能够使脉冲激光在光纤中进行放大和传输后保持种子激光的光谱特性.基于三波耦合方程开展数值仿真,研究了在对SPM进行"欠补偿","完全补偿"和"过补偿"的情况下,SPM预补偿对受激布里渊散射阈值和激光光谱特性的影响.开展了SPM预补偿实验研究,将脉冲激光的光谱宽度从1.4 GHz压缩到120 MHz.研究内容可以为窄线宽脉冲光纤激光系统的设计搭建提供参考.     

18 W single-stage single-frequency acoustically tailored Raman fiber amplifier

A single-mode polarization-maintaining fiber doped to increase the Raman gain while suppressing stimulated Brillouin scattering (SBS) was utilized in a single-stage counter-pumped Raman fiber amplifier. The SBS suppression was achieved through the acoustic tailoring of the core. A pump probe experiment was conducted to characterize the Brillouin gain and indicated the existence of multiple Brillouin peaks. When the amplifier was seeded with approximately 15 mW of 1178 nm light, 11.5 W of cw output power was obtained with a linewidth ≤2 MHz. The application of a thermal gradient to further mitigate the SBS process increased the output power to 18 W, thus providing a net amplifier gain >30 dB.     

Origin of temporally stable continuous-wave stokes emission in stimulated Brillouin scattering: evidence of spectral self-phase conjugation

We report results on the appearance of temporally stable Stokes emission in stimulated Brillouin scattering (SBS) excited by continuous-wave pump radiation in optical fiber. With increasing pump strength the stable component emerges from stochastic emission slightly above the SBS threshold to become the dominant contribution, independent of fiber characteristics. These findings are shown to be a manifestation of spectral self-phase conjugation, providing what is to our knowledge the first experimental evidence of this phenomenon in optics.     

A new method for measuring the threshold of stimulated Brillouin scattering

A new method for measuring the threshold of stimulated Brillouin scattering (SBS) based on the generation location of a Stokes beam is proposed for the first time to our knowledge. The length of the medium cell is selected to be longer than the free gain length of pump pulses in the Brillouin medium. The reflected light from a certain mirror in front of the medium cell is chosen as the reference beam, and the SBS threshold is measured by the "jump" of the delay between the Stokes beam and the reference beam. An 8-ns Q-switched single-longitudinal-mode pulse is used as the pump and the typical SBS medium FC-72 is selected as the nonlinear medium in our experiment. The SBS threshold intensity is measured to be 173-178 mW/cm 2 , which is consistent with existing results measured with the transmitted energy limiting method.     

受激布里渊散射光限幅输出波形控制研究

数值模拟了种子场诱导受激布里渊散射光限幅过程的限幅输出波形特性.得到利用种子场控制限幅脉冲波形的规律：选取种子场脉冲宽度为抽运脉冲宽度的五倍，抽运脉冲相对于种子脉冲的延迟时间控制在与抽运脉冲宽度相当时，限幅输出波形最佳.限幅输出波形同时受抽运光功率影响，随抽运能量的增加，限幅脉冲功率不断下降，直至趋于0. 关键词： 受激布里渊散射 限幅输出波形 注入种子     

Amplification effect on stimulated Brillouin scattering in the S-band forward G652 fiber Raman amplifier

The amplification effects on forward and backward stimulated Brillouin scattering (SBS) lines in the forward pumped S-band distributed G652 fiber Raman amplifier (FRA) have been studied. There is a pump threshold power of Stokes backward stimulated Brillouin scattering (B-SBS) line in the forward pumped G652 FRA, it is about 1 mW. The Stokes B-SBS lines are amplified by FRA and fiber Brillouin Brillouin gain. In experimental work, the saturation gain of the first order Stokes backward SBS line is about 58 dB and the saturation gain of 25-km G652 forward FRA is about 25 dB, so the gain of FBA is about 33 dB. The forward stimulated Brillouin scattering (F-SBS) is generated and amplified in S-band G652 FRA. The stimulated threshold powers of the forward first order Stokes SBS (SB1-), second order Stokes SBS (SB2-), and third order SBS (SB3-) in the forward pumped FRA are 2.3, 1.6, and 1.6 mW,respectively. In experimental work, the saturation gains of SB1-, SB2-, and SB3- are about 38, 62, and 60 dB, respectively. The saturation Raman gain of 25-km G652 forward FRA is about 8.8 dB, so the Brillouin gains of SB1-, SB2-, and SB3- are about 29.2, 53.2, and 51.2 dB, respectively. The forward and backward cascaded SBS lines have been observed.