CaCO_3颗粒模板法制备聚合物超亲水/超疏水表面

以碳酸钙(CaCO3)颗粒层为模板,运用简单的热压和酸蚀刻相结合的方法制备聚合物超亲水/超疏水表面.首先在玻璃基底上均匀铺撒一层CaCO3颗粒,以此作为模板,通过热压线性低密度聚乙烯(LLDPE)使CaCO3颗粒均匀镶嵌在聚合物表面,获得了超亲水性质;进一步经酸蚀得到了具有微米和亚微米多孔结构的表面,其水滴静态接触角(WCA)可达(152.7±0.8)°,滚动角小于3°,具备超疏水性质.表面浸润性能和耐水压冲击性能研究表明该超疏水表面具有良好的稳定性和持久性.用同样工艺微模塑/酸蚀刻其它疏水性聚合物,得到类似结果.     

Fabrication of Superhydrophobic Surface with Different Metal Films on Aluminum Alloy

A simple technique was developed for the fabrication of a superhydrophobic surface on the aluminum alloy sheets. Different hierarchical structures(Ag, Co, Ni and Zn) were formed on the aluminum surface by the galvanic replacement reactions. After the chemical modification of them with fluorination, the wettability of the surfaces was changed from superhydrophilicity to superhydrophobicity. Scanning electron microscopy(SEM), energy dispersive spectrometry(EDS) and water contact angle measurement were performed to characterize the morphological characteristic, chemical composition and superhydrophobicity of the surfaces. The as-prepared superhydrophobic surfaces showed a water contact angle as high as ca.160° and sliding angle as low as ca.3°. We hope the method to produce superhydrophobic surface can be used in many fields.     

Fabrication of functionalized aluminum compound petallike structure with superhydrophobic surface

The petallike structures, similar to that of a lotus leaf, were directly fabricated on the surface of aluminum sheets by a simple one‐step solution‐immersion process. It was found that the width of the nanoflakes ranges from 20 to 500 nm, and the length of the flakes is about several micrometers. The wettability of the surface with a hierarchical structure was changed from superhydrophilicity to superhydrophobicity by chemical modification with perfluorodecyltriethoxysilane (PDES). The static contact angles (CAs) for water on both of the modified surfaces were larger than 150° , which was closely related to the chemical modification and hierarchical structure. Furthermore, the surfaces retained good superhydrophobic stability in long‐term storage as well, which should be critical to the application of aluminum materials in engineering. Copyright © 2010 John Wiley & Sons, Ltd.     

A novel superhydrophobic surface based on low‐density polyethylene/ethylene‐propylene‐diene terpolymer thermoplastic vulcanizate

A novel superhydrophobic surface based on low‐density polyethylene (LDPE)/ethylene‐propylene‐diene terpolymer (EPDM) thermoplastic vulcanizate (TPV) was successfully fabricated where the etched aluminum foil was used as template. The etched aluminum template, consisted of countless micropores and step‐like textures, was obtained by metallographic sandpaper sanding and the subsequent acid etching. The surface morphology and the hydrophobic properties of the molded TPV surface were researched by using field emission scanning electron microscope and contact angle meter, respectively. From the microstructure observation of the superhydrophobic LDPE/EPDM TPV surface, the step‐like textures obtained via molding with etched aluminum foil template and a large number of fiber‐like structures resulted from the plastic deformation of LDPE matrix could be found obviously. The obtained TPV surface exhibited remarkable superhydrophobicity, with a contact angle of 152.0° ± 0.7° and a sliding angle of 3.1° ± 0.8°.     

Facile preparation of superhydrophobic nanorod surfaces through ion-beam irradiation

Obtaining superhydrophobic surfaces for their application in electronics and flexible wearable devices remains a significant challenge. Most previously reported methods for obtaining superhydrophobic surfaces involve complex and expensive preparation techniques and thus cannot be used for practical applications. Ion-beam irradiation is a simple and promising method for fabricating superhydrophobic nanostructures on large areas at a low cost. Ion-beam irradiation using argon and oxygen gases was used to prepare silica nanorod structures on glass substrates. This study is not just a modification of the surface of nanoparticles, but a change in nanoparticle shape. The nanorods were subsequently treated with perfluorooctyltriethoxysilane to obtain superhydrophobicity. The surface of the silica nanorods exhibited a static water contact angle of 153°, indicating superhydrophobicity. The combination of rough structures of silica nanorods and low surface energy resulted in superhydrophobicity. The surface properties were evaluated in detail using Fourier-transform infrared spectroscopy, field-emission scanning electron microscopy, and X-ray photoelectron spectroscopy. The proposed method is facile, inexpensive, and can be used for the large-scale production of nanorod structures for potential industrial applications.     

Transparent hydrophobic and superhydrophobic coatings fabricated using polyamide 12–SiO2 nanocomposite

Optically transparent hydrophobic and superhydrophobic coatings have been prepared using polyamide 12–SiO₂ nanocomposite (NC) on glass substrates by the spin‐coating method. The coatings have been optimized for their hydrophobicity and transparency. The transformation from hydrophobic to superhydrophobic is achieved with increase in roughness (R_a) which increases with SiO₂ content. These coatings are highly transparent in the entire visible region (400–800 nm). The influence of layer thickness on water contact angle (WCA) and optical transmittance of the coatings has been studied. Field emission scanning electron micrograph (FESEM) shows the presence of SiO₂ nanoparticles covered with polyamide homogenously on the surface and the particles are aggregated to form a rough structure. X‐ray diffraction (XRD) patterns show that the polyamide losses its crystalline structure in the composite. The preparation procedure reported here is simple and eco‐friendly. The dual nature of the coatings, that is, high transparency and superhydrophobicity in the entire visible region suggests for its potential usage in self‐cleanings, wind screen and optoelectronic applications. Copyright © 2016 John Wiley & Sons, Ltd.     

Facile Spray-Coating for Fabrication of Superhydrophobic SiO2/PVDF Nanocomposite Coating on Paper Surface

A facile and low-cost superhydrophobic nanocomposite coating on paper surface was fabricated through one-step simply spraying dispersion, using hydrophobic silica nanoparticles as a filter (SiNPs) and polyvinylidene fluoride (PVDF) as a film-forming material. Hydrophobic SiNPs were fabricated via co-hydropholysis and condensation of TEOS and long-chain alkyl silane based on a simple sol-gel process, and the surface chemical structure of SiNPs was characterized by Fourier transform infrared (FTIR) spectra. The wettability and morphology of the coating surface were measured by contact angle (CA) measurement and scanning electron microscope, respectively. The influence of the mass ratio of hydrophobic SiNPs to PVDF (M(SiNPs:PVDF)) on the superhydrophobicity of paper surface was studied. The results showed that when M(SiNPs:PVDF) was 3:1, the water CA was 156.0 ± 1.0° for the nanocomposite coating with micro/nano-hierarchical structure on paper surface. Further, such superhydrophobic nanocomposite coatings on paper surface showed little adhesive property with water. In addition, the prepared superhydrophobic nanocomposite coating could be applied in other substrates, such as wood, aluminum sheet, stainless steel, polytetrafluoroethylene (PTFE), etc.     

以砂纸为模板制作聚合物超疏水表面

报道了一种聚合物材料超疏水表面的简便制备方法. 以不同型号的金相砂纸为模板, 通过浇注成型或热压成型技术, 在聚合物表面形成不同粗糙度的结构. 接触角实验结果证明, 聚合物表面与水的接触角随着所用砂纸模板粗糙度的增加而加大, 其中粒度号为W7和W5砂纸制作的表面与水的接触角可超过150°, 显示出超疏水性质. 多种聚合物使用砂纸为模均可制备不同粗糙度及超疏水的表面, 本征接触角对复制表面浸润性的影响从Wenzel态到Cassie态而变小. 扫描电镜结果表明, 不规则形状的砂纸磨料颗粒构成了超疏水所需要的微纳米结构的模板.     

Formation of superhydrophobic cerium oxide surfaces on aluminum substrate and its corrosion resistance properties

Superhydrophobic cerium oxide film was introduced to aluminum substrate by an in‐situ growth process and surface modification. Different molar ratios between Ce(NO₃)₃ · 6H₂O and C₆H₁₂N₄ were involved in this research. The morphologies, chemical compositions and wetting properties of the films were analyzed by scanning electron microscopy (SEM), energy dispersive X‐ray detector, Fourier transfer infrared spectrometer and water contact angle (WCA) measurement, respectively. A great WCA of 158.8^o with a low angle hysteresis of about 3^o was obtained. Combination of uniform hierarchical micro‐nanostructure as revealed by SEM together with the hydrophobic alkyl groups from stearic acid was found to be responsible for the superior superhydrophobic property. The corrosion resistance performance of the superhydrophobic surface was evaluated by immersing in sodium chloride aqueous solution, the WCA kept as high as 152.1^o after immersion for 21 days, indicating our superhydrophobic surfaces had high chemical stability and durability in corrosive medium. Copyright © 2013 John Wiley & Sons, Ltd.     

Preparation of hierarchically structured PCL superhydrophobic membrane via alternate electrospinning/electrospraying techniques

Superhydrophobic polycaprolactone (PCL) membranes with hierarchical structure were fabricated via alternate electrospinning/electrospraying techniques. Electrospun PCL/methyl silicone oil (PCL/MSO) nanofibers were employed as substrate. PCL/MSO‐PCL microspheres (PCL/MSO‐PCL_MS) hierarchical membrane was prepared via electrosprayed PCL_MS as an additional layer on the substrate. Field emission scanning electron microscopy images showed the formation of hierarchical PCL/MSO‐PCL_MS membranes. Compared to pure PCL fibers substrate (120 ± 1.3°), the water contact angle (WCA) of MSO‐modified PCL membrane was 142 ± 0.7°. The most interesting observation was that the WCA of PCL_MS without any modification could be achieved to 146 ± 2.8°. On this basis, PCL/MSO‐PCL_MS hierarchical membrane possessed superhydrophobic surface with 150 ± 0.6° of WCA. The excellent surface roughness and air‐pocket capacity of hierarchical membranes would make the membranes more hydrophobic. The maximum oil (n‐hexane) adsorption capacity of PCL/MSO‐PCL_MS membrane was 32.53 g g^?1. Oil–water separation efficiencies of the superhydrophobic membranes were all higher than 99.93% after 10 cycles. The hierarchically structured PCL superhydrophobic membranes indicate the potential applications of environmentally friendly biopolymers as separation membranes. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 421–430     

Fabrication of durable superhydrophobic nanofibrous filters for oil‐water separation using three novel modified nanoparticles (ZnO‐NSPO,AlOO‐NSPO,and TiO2‐NSPO)

Three reusable and durable superhydrophobic nanofibrous filters were prepared by dip coating the nanofibrous fabric in the three different dispersed solutions of the newly modified nanoparticles (ZnO‐NSPO, AlOO‐NSPO, and titanium dioxide [TiO₂]‐NSPO). The contact angle results proved that the TiO₂‐NSPO coated nanofibrous polyacrylonitrile (PAN) filter was hydrophobic with the water contact angle (WCA) of 141° while the ZnO‐NSPO and AlOO‐NSPO coated nanofibrous PAN filters were superhydrophobic with the WCA of 168° and 152°, respectively. The as‐prepared filters can be utilized as an effective martial for oil‐water separation with separation efficiency of over 98%.     

聚苯硫醚超疏水复合涂层的制备与性能

利用工业原料聚苯硫醚微粉和疏水性二氧化硅纳米粉末,采用喷涂法在瓷砖表面制备了疏水复合涂层.研究了热处理温度、组分配比对涂层表面形貌、粗糙度和接触角的影响,发现随着热处理温度升高,涂层表面粗糙度增大,随着疏水性二氧化硅含量的增加,由于表面聚集的疏水性二氧化硅增多,涂层疏水性增强,在热处理温度为280℃、疏水性二氧化硅与聚苯硫醚质量比为1∶1时,可获得超疏水涂层,涂层的接触角大于150°,滚落角小于4°,pH值为1～14的水溶液在其表面都具有很高的接触角.超疏水涂层具有良好的自清洁效果,并且经落沙法实验测定,超疏水涂层耐刮伤性能良好.     

Superhydrophilic/superhydrophobic surfaces fabricated by spark‐coating

In this study, the authors researched the preparations of superhydrophilic/superhydrophobic surfaces on commercial cup stock polyethylene coated papers by using sparked aluminum nanoparticles deposited on substrates through a sparking process. In this stage, the surface was porous and showed superhydrophilic properties. The samples were then annealed in air at various temperatures and some transformed to superhydrophobicity. It is well known that a suitable roughness in combination with low surface energy has been required to obtain superhydrophobic surfaces. Therefore, it is believed that during annealing process, when polyethylene is diffused from the substrate through the nanoparticle films and the superhydrophobic characteristics were created. The scanning electron microscope images showed that the film surfaces had a fluffy structure for both the as‐deposited and the annealed samples. However, the atomic force microscopy phase images showed completely different surface properties. Moreover, the X‐ray photoelectron spectroscopy spectra showed different surface chemical compositions. The experimental results revealed that the working temperature to produce superhydrophobic surfaces depended on the sparked film thickness. Furthermore, in order to prove the assumption explained above, glass and poly (methyl methacrylate) were also used as substrates.     

Control of the water adhesion on hydrophobic micropillars by spray coating technique

We present an alternative approach for controlling the water adhesion on solid superhydrophobic surfaces by varying their coverage with a spray coating technique. In particular, micro-, submicro-, and nanorough surfaces were developed starting from photolithographically tailored SU-8 micropillars that were used as substrates for spraying first poly(tetrafluoroethylene) submicrometer particles and subsequently iron oxide nanoparticles. The sprayed particles serve to induce surface submicrometer and nanoscale roughness, rendering the SU-8 patterns superhydrophobic (apparent contact angle values of more than 150°), and also to tune the water adhesion between extreme states, turning the surfaces from “non-sticky” to “sticky” while preserving their superhydrophobicity. The influence of the chemical properties and of the geometrical characteristics of the functionalized surfaces on the wetting properties is discussed within the frame of the theory. This simple method can find various applications in the fabrication of microfluidic devices, smart surfaces, and biotechnological and antifouling materials.     

A facile method for fabrication of superhydrophobic coating on aluminum alloy

A superhydrophobic coating applied in corrosion protection was successfully fabricated on the surface of aluminum alloy by chemical etching and surface modification. The water contact angle on the surface was measured to be 161.2° ± 1.7° with sliding angle smaller than 8°, and the superhydrophobic coating showed a long service life. The surface structure and composition were then characterized by means of SEM and XPS. The electrochemical measurements showed that the superhydrophobic coating significantly improved the corrosion resistance of aluminum alloy. The superhydrophobic phenomenon of the prepared surface was analyzed with Cassie theory, and it was found that only about 6% of the water surface is in contact with the metal substrate and 94% is in contact with the air cushion. Copyright © 2011 John Wiley & Sons, Ltd.     

One‐step immersion method for fabricating superhydrophobic aluminum alloy with excellent corrosion resistance

This work develops a facile one‐step immersion method for preparing the superhydrophobic aluminum alloy, i.e. the aluminum alloy is treated with stearic acid (STA)–ethanol–H₂O solution at 60 °C for 35 h. Results show that the aluminum alloy achieves flower‐like structure with both a great deal of pillars and pores, while the long hydrophobic alkyl chains are chemically grafted onto the hierarchical surface. Meanwhile, the water contact angle at the aluminum alloy surface gradually enhances with the decrease of the ethanol–H₂O volume ratio, and the water contact angle and rolling angle of 156.2° and 5°, respectively, are obtained when the ethanol–H₂O volume ratio is 1:3. Moreover, results show that the higher water contact angle at the aluminum alloy, the better corrosion resistance of the aluminum alloy. Consequently, the aluminum alloy with the superhydrophobic property has the best corrosion resistance, durability, and stability in corrosive environments. Copyright © 2016 John Wiley & Sons, Ltd.     

Creation of “Rose Petal” and “Lotus Leaf” Effects on Alumina by Surface Functionalization and Metal‐Ion Coordination

Functional differences between superhydrophobic surfaces, such as lotus leaf and rose petals, are due to the subtle architectural features created by nature. Mimicry of these surfaces with synthetic molecules continues to be fascinating as well as challenging. Herein, we demonstrate how inherently hydrophilic alumina surface can be modified to give two distinct superhydrophobic behaviors. Functionalization of alumina with an organic ligand resulted in a rose‐petal‐like surface (water pinning) with a contact angle of 145° and a high contact angle hysteresis (±69°). Subsequent interaction of the ligand with Zn²⁺ resulted in a lotus‐leaf‐like surface with water rolling behavior owing to high contact angle (165°) and low‐contact‐angle‐hysteresis (±2°). In both cases, coating of an aromatic bis‐aldehyde with alkoxy chain substituents was necessary to emulate the nanowaxy cuticular feature of natural superhydrophobic materials.     

Effects of contact angle hysteresis on ice adhesion and growth on superhydrophobic surfaces under dynamic flow conditions

In this paper, the icephobic properties of superhydrophobic surfaces are investigated under dynamic flow conditions using a closed-loop low-temperature wind tunnel. Superhydrophobic surfaces were prepared by coating aluminum and steel substrate plates with nano-structured hydrophobic particles. The superhydrophobic plates, along with uncoated controls, were exposed to a wind tunnel air flow of 12 m/s and ?7 °C with deviations of ±1 m/s and ±2.5 °C, respectively, containing micrometer-sized (～50 μm in diameter) water droplets. The ice formation and accretion were observed by CCD cameras. Results show that the superhydrophobic coatings significantly delay ice formation and accretion even under the dynamic flow condition of highly energetic impingement of accelerated supercooled water droplets. It is found that there is a time scale for this phenomenon (delay in ice formation) which has a clear correlation with contact angle hysteresis and the length scale of the surface roughness of the superhydrophobic surface samples, being the highest for the plate with the lowest contact angle hysteresis and finest surface roughness. The results suggest that the key for designing icephobic surfaces under the hydrodynamic pressure of impinging droplets is to retain a non-wetting superhydrophobic state with low contact angle hysteresis, rather than to only have a high apparent contact angle (conventionally referred to as a “static” contact angle).     

Nanostructures increase water droplet adhesion on hierarchically rough superhydrophobic surfaces

Hierarchical roughness is known to effectively reduce the liquid-solid contact area and water droplet adhesion on superhydrophobic surfaces, which can be seen for example in the combination of submicrometer and micrometer scale structures on the lotus leaf. The submicrometer scale fine structures, which are often referred to as nanostructures in the literature, have an important role in the phenomenon of superhydrophobicity and low water droplet adhesion. Although the fine structures are generally termed as nanostructures, their actual dimensions are often at the submicrometer scale of hundreds of nanometers. Here we demonstrate that small nanometric structures can have very different effect on surface wetting compared to the large submicrometer scale structures. Hierarchically rough superhydrophobic TiO(2) nanoparticle surfaces generated by the liquid flame spray (LFS) on board and paper substrates revealed that the nanoscale surface structures have the opposite effect on the droplet adhesion compared to the larger submicrometer and micrometer scale structures. Variation in the hierarchical structure of the nanoparticle surfaces contributed to varying droplet adhesion between the high- and low-adhesive superhydrophobic states. Nanoscale structures did not contribute to superhydrophobicity, and there was no evidence of the formation of the liquid-solid-air composite interface around the nanostructures. Therefore, larger submicrometer and micrometer scale structures were needed to decrease the liquid-solid contact area and to cause the superhydrophobicity. Our study suggests that a drastic wetting transition occurs on superhydrophobic surfaces at the nanometre scale; i.e., the transition between the Cassie-Baxter and Wenzel wetting states will occur as the liquid-solid-air composite interface collapses around nanoscale structures. Consequently, water adheres tightly to the surface by penetrating into the nanostructure. The droplet adhesion mechanism presented in this paper gives valuable insight into a phenomenon of simultaneous superhydrophobicity and high water droplet adhesion and contributes to a more detailed comprehension of superhydrophobicity overall.     

Strelitzia reginae leaf as a natural template for anisotropic wetting and superhydrophobicity

Artificial surfaces that exhibit unidirectional water spreading and superhydrophobicity are obtained by Strelitzia reginae leaves. Both green and dried leaves are used, thus exploiting the plant senescence. We demonstrate that the natural drying process of the leaves strongly affects the surface morphology and wettability. Polymeric stamps from the green leaf show an arrangement of periodic microridges/microgrooves that favor anisotropic wetting, with a water contact angle (WCA) variation of about 21% along the two principal directions. Instead, the shrinkage of the leaf tissue, as a consequence of the natural dehydration process, induces an enhancement of the superficial corrugation. This results in the establishment of a superhydrophobic state, which shows a WCA of up to 160°, and water rolling off. S. reginae leaves are therefore easily accessible stamps suitable for controlling wettability and realizing surfaces that exhibit various wetting behaviors.