H2O2 adsorption on the BN and SiC nanotubes: A DFT study

We have performed a comparative density functional theory study on adsorption of hydrogen peroxide (H₂O₂) on the boron nitride and silicon carbide nanotubes (BNNT and SiCNT) in terms of energetic, geometric, and electronic properties. It has been found that the molecule is chemically adsorbed on both of the tubes so that its interaction with SiCNT (adsorption energy ∼−0.97 eV) is much stronger than that with BNNT (adsorption energy ∼−0.47 eV). The H₂O₂ adsorption on BNNT slightly decreases its work function, increasing the field electron emission from the BNNT surface while it may not affect that of the SiCNT. In addition, the adsorption process may increase the electrical conductivity of SiCNT while does not affect that of the BNNT, significantly. We believe that the SiCNT may be a potential candidate for detection of H₂O₂.     

Adsorption of oxygen molecular on pristine and defected SiC nanotubes

The structural and electronic properties of oxygen molecular adsorbed on the exterior surface of pristine and N_C or B_C defected (10,0) or (6,6) SiCNT have been investigated systematically using the first-principles projector-augmented wave potential within the density-functional theory under the generalized-gradient approximation. We find that for both pristine tubes the preferred adsorption sites of the O₂ molecule are above and nearly parallel to armchair Si-C bond whether physisorption or chemisorption. The strong chemical interaction between O₂ molecule and tube leads to not only a vanishing in magnetism of the O₂ molecule but also an outward relaxation of the underlying Si-C bond. The C atom substituted by N or B atom assists O₂ molecule adsorption above and nearly parallel to zigzag Si-N or Si-B bond as well as imparts a metallic character on the SiCNTs with higher concentration of the defects or a magnetism on the SiCNTs with lower concentration of the defects. Therefore, a combination of N or B doping followed by exposure to air may be an effective way to tune the electronic properties of the semiconducting SiCNTs. Furthermore, the lower binding energies for the pair of oxygen interstitials chemisorbed on N_C or B_C defected (10,0) or (6,6) SiCNT show that the oxygen molecule will dissociate to the pair of oxygen interstitials at the sidewall of N_C or B_C defected SiCNTs.     

Adsorption of water molecule on (001) and (110) surfaces of MgH2

First principle calculations have been performed to explore the adsorption characteristics of water molecule on (001) and (110) surfaces of magnesium hydride. The stable adsorption configurations of water molecule on the surfaces of MgH₂ were identified by comparing the total energies of different adsorption states. The (110) surface shows a higher reactivity with H₂O molecule owing to the larger adsorption energy than the (001) surface, and the adsorption mechanisms of water molecule on the two surfaces were clarified from electronic structures. For both (001) and (110) surface adsorptions, the O p orbitals overlapped with the Mg s and p orbitals leading to interactions between O and Mg atoms and weakening the O–H bonds in water molecule. Due to the difference of the bonding strength between O and Mg atoms in the (001) and (110) surfaces, the adsorption energies and configurations of water molecule on the two surfaces are significantly different.     

SiO adsorption on a p(2 × 2) reconstructed Si(1 0 0) surface

We have investigated the adsorption mechanism of SiO molecule incident on a clean Si(1 0 0) p(2 × 2) reconstructed surface using density functional theory based methods. Stable adsorption geometries of SiO on Si surface, as well as their corresponding activation and adsorption energies are identified. We found that the SiO molecule is adsorbed on the Si(1 0 0) surface with almost no activation energy. An adsorption configuration where the SiO binds on the channel separating the dimer rows, forming a Si-O-Si bridge on the surface, is the energetically most favourable geometry found. A substantial red-shift in the calculated vibrational frequencies of the adsorbed SiO molecule in the bridging configurations is observed. Comparison of adsorption energies shows that SiO adsorption on a Si(1 0 0) surface is energetically less favourable than the comparable O₂ adsorption. However, the role of SiO in the growth of silicon sub-oxides during reactive magnetron plasma deposition is expected to be significant due to the relatively large amount of SiO molecules incident on the deposition surface and its considerable sticking probability. The stable adsorption geometries found here exhibit structural properties similar to the Si/SiO₂ interface and may be used for studying SiO_x growth.     

Mechanism of H2S molecule adsorption on the GaAs(100) surface: Ab initio quantum-chemical analysis

Ab initio quantum-chemical cluster calculations within the density-functional theory were carried out to study the mechanism of H₂S molecule adsorption on the gallium-rich surface of GaAs(100). It was shown that adsorption can occur in four stages: molecular adsorption; dissociative adsorption, during which an HS radical is adsorbed on a gallium atom comprising a dimer while the detached hydrogen atom is adsorbed on another surface atom of the semiconductor; hydrogen adatom migration between neighboring surface atoms of the semiconductor; and the formation of a Ga-S-Ga bridge bond and of a hydrogen molecule. The stationary-state energies and energy barriers to transitions between these states were determined. The conclusions drawn based on an analysis of calculated diagrams of the potential energy of the processes that occur are in good agreement with the experimental data available in the literature.     

Adsorption of CO, NH3 and O2 on Fe site of La0.875Sr0.125FeO3 (0 1 0) surface by density function theory calculation

The adsorption of CO, NH₃ and O₂ gas molecules on Fe site of La_0.875Sr_0.125FeO₃ (0 1 0) surface has been investigated based on the density functional theory (DFT) with the spin polarized generalized gradient approximation (GGA). The optimal adsorption orientations as well as the adsorption energies for these molecules adsorption on Fe site of La_0.875Sr_0.125FeO₃ (0 1 0) surface are derived. Results show that adsorption configurations with C-down for CO, N-down for NH₃ are stable. For the O₂ molecule adsorption, the mode with an angle about 120° between the oxygen molecule and La_0.875Sr_0.125FeO₃ (0 1 0) surface is stable.     

Adsorption of molecular SiO2 on a clean Si(1 0 0) surface

We have investigated the adsorption of molecular (gaseous) SiO₂ on a clean Si(1 0 0) p(2 × 2) reconstructed surface using density functional theory based methods. The SiO₂ molecule is found to be chemisorbed on various sites on the Si surface and the most energetically favourable structure is on top of the dimers. The minimum energy pathways for the various adsorption channels indicate that the reaction is barrierless in all cases. The corresponding vibrational spectrum is also calculated and the adsorbed molecules are, as expected, found to have red-shifted vibrational frequencies. The energetically favourable adsorption sites and adsorption energies are comparable to the results found for SiO.     

CO adsorption on small Aun（n=1-7） clusters supported on a reduced rutile TiO2（110） surface:a first-principles study

CO adsorption on small Au n(n = 1-7) clusters which are supported by a partially reduced rutile TiO 2(110) surface has been investigated by the first-principles method.The low coordinated sites of Au clusters are favorable for CO adsorption.CO-Au n-TiO 2 system displays surface magnetism.There is a strong interaction between the adsorbed CO molecule and the supported Au clusters.     

H2O在Pt(100)表面的预吸附态与高迁移性能

本文采用ASED-MO方法,计算了H₂O分子在Pt(100)面上不同吸附取向、不同吸附位置时的结合能,以及表面扩散激活能和扩散系数.计算结果表明,H₂0分子必须通过氢原子朝向衬底的预吸附态.才能进人氧原子朝向衬底的垂直顶位化学吸附状态.当H₂O分子处于上述预吸附态时,势能面极为平坦,扩散系数大,迁移性高. 关键词：     

The chemisorption of pentacene on Si(0 0 1)-2 × 1

Adsorption structures of the pentacene (C₂₂H₁₄) molecule on the clean Si(0 0 1)-2 × 1 surface were investigated by scanning tunneling microscopy (STM) in conjunction with density functional theory calculations and STM image simulations. The pentacene molecules were found to adsorb on four major sites and four minor sites. The adsorption structures of the pentacene molecules at the four major sites were determined by comparison between the experimental and the simulated STM images. Three out of the four theoretically identified adsorption structures are different from the previously proposed adsorption structures. They involve six to eight Si-C covalent chemical bonds. The adsorption energies of the major four structures are calculated to be in the range 67-128 kcal/mol. It was also found that the pentacene molecule hardly hopped on the surface when applying pulse bias voltages on the molecule, but was mostly decomposed.     

BaxOy小团簇修饰Ru(0001)表面的结构稳定性和氮分子吸附性质

为了说明钡助剂的存在形式, 本文采用第一性原理方法研究了Ba_xO_y小团簇修饰Ru(0001)表面的结构稳定性和氮分子吸附性质. 基于总能的热力学分析发现, 在实验条件下(500 K, P_H2O/P_H2<10^-3), Ba₂O团簇比BaO₂, BaO, Ba和O等团簇(原子)更加稳定. 这证实含有金属性钡原子的团簇也是氧化钡助剂可能的工作状态. 表面电荷差分密度说明Ba₂O团簇的氧和钡原子与衬底的作用不同. 不过Ba₂O团簇氧和钡原子附近的氮分子吸附行为相似, Ba₂O团簇增强了氮分子和衬底的相互作用. Ba₂O团簇氧和钡原子附近的氮分子吸附能分别为0.78 和0.88 eV, 均大于清洁表面的0.67 eV. 氮分子间距和氮分子的拉伸振动频率都表明Ba₂O团簇在一定程度上活化了吸附氮分子. Ba₂O团簇氧和钡原子附近的N–N键长分别为0.117和0.116 nm, 大于清洁表面的0.114 nm. 氧和钡原子附近氮分子的拉伸振动频率分别为 1888 和1985 cm^-1, 小于清洁表面的2193 cm^-1. 电荷差分密度的计算结果说明, 削弱作用主要来自于Ba₂O团簇中钡离子和氮分子间的静电作用. 两者间的静电作用增加了氮分子π 反键轨道的占据数, 促进了氮分子极化, 从而削弱氮分子键.     

TiO2分子在GaN(0001)表面吸附的理论研究

采用基于密度泛函理论的平面波超软赝势法,计算了TiO₂分子在GaN(0001)表面的吸附成键过程、吸附能量和吸附位置. 计算结果表明不同初始位置的TiO₂分子吸附后,Ti在fcc或hcp位置,两个O原子分别与表面两个Ga原子成键,Ga-O化学键表现出共价键特征,化学结合能达到7.932-7.943eV,O-O连线与GaN[1120]方向平行,与实验观测(100)[001] TiO₂//(0001)[1120]GaN一致. 通过动力学过程计算分析,TiO₂分子吸附过程经历了物理吸附、化学吸附与稳定态形成的过程,稳定吸附结构和优化结果一致. 关键词： GaN(0001)表面 2分子')" href="#">TiO₂分子 密度泛函理论 吸附     

Molecular orbital study of the chemisorption of carbon monoxide on a tungsten (100) surface

The adsorption energies of carbon monoxide chemisorbed at various sites on a tungsten (100) surface have been calculated by extended Hückel molecular orbital theory (EHMO). The concept of a “surface molecule” in which CO is bonded to an array of tungsten atoms W_n has been employed. Dissociative adsorption in which C occupies a four-fold, five-coordination site and O occupies either a four- or two-fold site has been found to be the most stable form for CO on a W surface. Stable one-fold and two-fold sites of molecularly adsorbed CO have also been found in which the CO group is normal to the surface plane and the C atom is nearest the surface. Adsorption energies and molecular orbitals for the stable molecularly and dissociatively adsobred CO sites are compared with the experimental data on various types of adsorbed CO, i.e., virgin-, α-, and β-CO. Models are suggested for each of these adsorption types. The strongest bonding interactions occur between the CO 5σ orbital and the totally symmetric 5d and 6s orbitals of the W_n cluster. Possible mechanisms for conversion of molecularly adsorbed CO to dissociatively adsorbed CO are proposed and the corresponding activation energies are estimated.     

Au(110)表面结构和氧原子吸附的第一性原理研究

用密度泛函理论(DFT)研究了金属Au(110)表面结构以及氧原子的吸附状态.计算得到Au(110)-(1×2)缺列再构表面原子的弛豫分别是-15.0%(Δd₁₂/d₀)和-1.1%(Δd₂₃/d₀),表面能为52.7 meV/²,功函数Φ=5.00 eV;Au(110)-(1×3)缺列再构表面的Δd_{1 关键词： 缺列再构Au(110)表面 STM图像 氧原子吸附}     

Hydrogen adsorption on Pt-decorated closed-end armchair (3,3), (4,4) and (5,5) single-walled carbon nanotubes

ABSTRACT

Structures of small lengths of capped (3,3), (4,4) and (5,5) single-walled carbon nanotubes (SWCNTs) and their structures decorated by Pt atom and Pt_n clusters (n = 2–4) were obtained using density functional theory calculations. Binding abilities of Pt atom and Pt_n clusters on the outer surface of SWCNTs at various adsorption sites were explored. Adsorptions of H₂ onto Pt atom of the Pt-decorated (3,3), (4,4) and (5,5) SWCNTs were studied and their adsorption energies are reported. The thermodynamic properties and equilibrium constants for H₂ adsorptions on the Pt₄-decorated (3,3), (4,4) and (5,5) SWCNTs were obtained. The adsorption of H₂ on the Pt atom of the Pt₄/(3,3) SWCNT was found to be the most preferred reaction of which enthalpy and free energy changes at room temperature are ?46.61 and ?23.99 kcal/mol, respectively.     

The role of poly(methacrylic acid) conformation on dispersion behavior of nano TiO2 powder

To exploit the advantages of nanoparticles for various applications, controlling the dispersion and agglomeration is of paramount importance. Agglomeration and dispersion behavior of titanium dioxide (TiO₂) nanoparticles was investigated using electrokinetic and surface chemical properties. Nanoparticles are generally stabilized by the adsorption of a dispersant (polyelectrolyte) layer around the particle surface and in this connection ammonium salt of polymethacrylic acid (Darvan C) was used as dispersant to stabilize the suspension. The dosages of polyelectrolyte were optimized to get best dispersion stability by techniques namely particle charge detector (13.75 mg/g) and adsorption (14.57 mg/g). The surface charge of TiO₂ particles changed significantly in presence of dispersant Darvan C and isoelectric point (iep) shifted significantly towards lower pH from 5.99 to 3.37. The shift in iep has been quantified in terms of free energy of interaction between the surface sites of TiO₂ and the adsorbing dispersant Darvan C. Free energies of adsorption were calculated by electrokinetic data (−9.8 RT unit) and adsorption isotherms (−10.56 RT unit), which corroborated well. The adsorption isotherms are of typical Langmuir type and employed for calculation of free energy. The results indicated that adsorption occurs mainly through electrostatic interactions between the dispersant molecule and the TiO₂ surface apart from hydrophobic interactions.     

CO methanation on Ni(1 1 1) and modified Ni3Al(1 1 1) surfaces: A first-principle study

The adsorption energies of intermediates in CO methanation on the modified Ni₃Al(1 1 1) surface and the Ni(1 1 1) surface are calculated using density functional theory. A microkinetic analysis based on the calculated adsorption energies is performed to explain the different kinetics of CO methanation catalyzed by Ni₃Al and Ni powders. The electronic structures of different atoms on the modified Ni₃Al surface are also presented, and correlate well with the adsorption energies and geometries.     

Density-functional study of CO adsorbed on RhN （N = 2-19） clusters

We investigate the structural, electronic and adsorption properties of one single CO molecule adsorbed on Rh_N (N = 2-19) clusters, using the density-functional theory in the spin-polarized generalized gradient approximation. It is found that the structural growth model of the Rh_N clusters transforms from double layers (N = 12-16) to three layers (N = 17-19). Three different adsorption types are the atop site adsorption for N = 6, 8, 9, 11, 12, the bridge site adsorption for N = 2-5, 7, 10, 13-15, 17 and the face adsorption for N = 16, 18, 19. The adsorption abilities of Rh_N clusters are related to C-O bond length, vibrational frequency, adsorption energy and the charge transfer between CO and Rh clusters as well as the electronic density of state. With the increase of Rh cluster size, the adsorption energy of CO adsorbed on Rh_N clusters tends to be 2.2 eV-2.3 eV, which is 0.2 eV-0.3 eV larger than the theoretical value (about 2.0 eV) of CO molecule adsorption on clean Rh (111) surface.     

N-doped graphene as a nanostructure adsorbent for carbon monoxide: DFT calculations

ABSTRACT

This work reports the physisorption of carbon monoxide (CO) on the surface of N-doped graphene. To study the adsorption of CO on N-doped graphene, some quantum chemical calculations were used through density functional theory. Based on our results, it can be found that the CO molecule could be adsorbed on the surface of N-doped graphene physically with the adsorption energies (E_ads) of ?2.9 and ?0.8 kcal mol^?1 (depends on the kind of configuration) while positive adsorption energies were calculated upon adsorption of CO on pristine graphene. We used the charge analysis for calculation of the net transferred charge of adsorbed CO on pristine and N-doped graphene sheets to evaluate the sensing ability of surface. The global indices of reactivity were calculated from the differences of the lowest unoccupied molecular orbital and highest occupied molecular orbital energies. Graphs for density of states point to some orbital hybridisation between CO molecule and N-doped graphene. Consequently, the N-doped graphene transforms the existence of CO molecules into electrical signal, and it may be potentially used as a sensor for CO.     

Hybrid HF–DFT modeling of monolayer water adsorption on (001) surface of cubic BaHfO3 and BaZrO3 crystals

First-principles calculations have been used to study the atomic structure, preferred sites and adsorption energies for water adsorption at different terminations of the cubic phase of perovskite-structured BaHfO₃ and BaZrO₃. By considering different initial positions of water molecules, the possibility of water dissociation has been investigated. It is demonstrated that the site selectivity and the form of adsorbed molecule can be affected by the choice of surface unit cell. Dissociative adsorption was found to be favorable for all surfaces in consideration. Hydroxylation of ZrO₂- and HfO₂-terminated surfaces is accomplished by a noticeable reconstruction of the surface structure of cubic phase towards the orthorhombic phase. Calculated atomic charges in bare and hydroxylated surfaces show that BaHfO₃ crystal is slightly more ionic than BaZrO₃.