Nanowear on polymer films of different architecture

In this paper, we describe atomic force microscope (AFM) friction experiments on different polymers. The aim was to analyze the influence of the physical architecture of the polymer on the degree and mode of wear and on the wear mode. Experiments were carried out with (1) linear polystyrene (PS) and cycloolefinic copolymers of ethylene and norbornene, which are stabilized by entanglements, (2) mechanically stretched PS, (3) polyisoprene-b-polystyrene diblock copolymers, with varying composition, (4) brush polymers consisting of a poly(methyl methacrylate) (PMMA) backbone and PS side chains, (5) PMMA and PS brushes grafted from a silicon wafer, (6) plasma-polymerized PS, and (7) chemically cross-linked polycarbonate. For linear polymers, wear depends critically on the orientation of the chains with respect to the scan direction. With increasing cross-link density, wear was reduced and ripple formation was suppressed. The cross-linking density was the dominating material parameter characterizing wear.     

Radiation‐induced fabrication of polymer nanoporous materials from microphase‐separated structure of diblock copolymers as a template

Polymer nanoporous materials with periodic cylindrical holes were fabricated from microphase‐separated structure of diblock copolymers consisting of a radiation‐crosslinking polymer and a radiation‐degrading polymer through simultaneous crosslinking and degradation by γ‐irradiation. A polybutadiene‐block‐poly(methyl methacrylate) (PB‐b‐PMMA) diblock copolymer film that self‐assembles into hexagonally packed poly(methyl methacrylate) cylinders in polybutadiene matrix was irradiated with γ‐rays. Solubility test, IR spectroscopy, and TEM and SEM observations for this copolymer film in comparison with a polystyrene‐block‐poly(methyl methacrylate) diblock copolymer film revealed that poly(methyl methacrylate) domains were removed by γ‐irradiation and succeeding solvent washing to form cylindrical holes within polybutadiene matrix, which was rigidified by radiation crosslinking. Thus, it was demonstrated that nanoporous materials can be prepared by γ‐irradiation, maintaining the original structure of PB‐b‐PMMA diblock copolymer film. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5916–5922, 2007     

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998     

Poly(sodium styrene sulfonate)-b-poly(methyl methacrylate) diblock copolymers through direct atom transfer radical polymerization: Influence of hydrophilic–hydrophobic balance on self-organization in aqueous solution

A series of poly(sodium styrene sulfonate)-b-poly(methyl methacrylate), PSSNa-b-PMMA, amphiphilic diblock copolymers have been synthesized through atom transfer radical polymerization (ATRP) of methyl methacrylate (MMA) in N,N-dimethylformamide/water mixtures, starting from a PSSNa macroinitiator. The kinetics of the polymerization was followed by ¹H NMR, while the chemical composition of the copolymers was verified by a variety of techniques, such as ¹H NMR, FTIR and TGA. The MMA content of the copolymers ranges from 0 up to 60 mol%, while the number–average molecular weight of the PSSNa macroinitiator was 9000 g/mol. The self-association of the diblock copolymers in aqueous solution was compared to the respective behavior of similar random P(SSNa-co-MMA) copolymers through optical density measurements, pyrene fluorescence probing, dynamic light scattering and surface tension measurements. It is shown that the diblock copolymers form micellar structures in water, characterized by an increasing hydrophobic character and a decreasing size as the length of the PMMA block increases. These micelle-like structures turn from surface inactive to surface active as the length of the PMMA block increases. Moreover, contrary to the MMA-rich random copolymers, the respective diblock copolymers form water insoluble polymer/surfactant complexes with cationic surfactants such as hexadecyltrimethyl ammonium bromide (HTAB), leading to materials with antimicrobial activity.     

Preparation of PTBA‐PAA‐PMMA Compatibilizer for PET‐PMMA Blends by Atom Transfer Radical Polymerization

The synthesis of diblock copolymer of tert butyl acrylate and methyl methacrylate (PTBA‐b‐PMMA) was prepared by Atom Transfer Radical Polymerization (ATRP). At the outset, macroinitiator of tert butyl acrylate (TBA) was prepared by using N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) ligand, Cuprous Bromide (CuBr) catalyst, and ethyl 2‐bromo isobutyrate (2‐EiBBr) initiator. Immediately after the intake of the utmost TBA in the macroinitiator, the second monomer, methyl methacrylate (MMA) was added to the reaction medium, for further polymerization. In these experiments the compositions of the monomers were varied, although the concentrations of ligand, catalyst and the initiator were kept constant. Subsequently, the diblock copolymers were hydrolyzed, under acidic conditions, using HCl catalyst, to obtain an amphiphilic copolymer. These block copolymers were characterized by NMR, IR, GPC, and DSC techniques. These copolymers will be used in, powder coatings, pigment dispersions, and as compatibilizers in polymer blends.     

Direct access to functional (Meth)acrylate copolymers through transesterification with lithium alkoxides

A straightforward and efficient synthetic method that transforms poly(methyl methacrylate) (PMMA) into value‐added materials is presented. Specifically, PMMA is modified by transesterification to produce a variety of functional copolymers from a single starting material. Key to the reaction is the use of lithium alkoxides, prepared by treatment of primary alcohols with LDA, to displace the methyl esters. Under optimized conditions, up to 65% functionalization was achieved and copolymers containing alkyl, alkene, alkyne, benzyl, and (poly)ether side groups could be prepared. The versatility of this protocol was further demonstrated through the functionalization of both PMMA homo and block copolymers obtained through either radical polymerization (traditional and controlled) or anionic procedures. The scope of this strategy was illustrated by extension to a range of architectures and polymer backbones. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1566–1574     

Understanding the Miscibility and Morphology of Poly(methyl methacrylate) and Styrenic Copolymer Blends of Tunable Domain Sizes

In the present study, we have investigated the miscibility, morphology and mechanical behavior of poly(methyl methacrylate) (PMMA) blends with a series of poly(styrene-co-maleic anhydride) (SMA) copolymers containing varying amounts of maleic anhydride (MA) content (from 8 to 26%). The experimental findings have been substantiated by the modeling studies to gain fundamental understanding of the observed phenomena with respect to the miscibility of the PMMA and SMA blends of a given MA content. The morphological differences, molecular weights, domain sizes and mechanical behavior of the blends at a given ratio of PMMA and copolymers have been investigated and a correlation has been made between the morphological understanding to the molecular weights and mechanical properties. The results indicate that the PMMA/SMA blends are miscible only at a certain MA content providing transparent PMMA/SMA blends without affecting any of the enabling properties of PMMA that are of commercial interest through a facile melt mixing process. The surface hardness and % recovery (nano-indentation) of these blends were evaluated as well to gain fundamental understanding of the surface characteristics and mechanicals of the blends.     

Synthesis of functional graft copolymers by solution copolymerization and their evaluation as dispersants in nonaqueous phase dispersion polymerization

The poly(HEMA‐co‐MMA‐g‐PMMA) graft copolymer was prepared with a poly(methyl methacrylate) (PMMA) macromonomer, 2‐hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA), and its application as a dispersant for the nonaqueous phase dispersion polymerization of polystyrene (PST) was investigated. Monodisperse PST particles were obtained with two‐dimensionally tailored graft copolymers, with the number of grafted chains controlled and the polar component (HEMA) in the backbone chains balanced. As for the reactor, a stirred vessel with moderate agitation yielded uniform polymer particles, whereas sealed glass ampules with an overturning motion yielded broader size distributions. Increasing the polarity of the solvent in the continuous phase yielded smaller polymer particles with a gradual deterioration of monodispersity. Uniform polymer particles with a coefficient of variation of less than 6% were obtained up to 30 wt % solid contents. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1788–1798, 2003     

Synthesis of Propylene Diblock Copolymers via Metallocene and Borane Chemistry

An isotactic chain end unsaturated polypropylene was prepared by the homogeneous metallocene catalyst Et(Ind)₂ZrCl₂ with MAO. Herein, the chain end unsaturated polypropylene proceeded the hydroboration reaction to prepare borane‐containing polypropylene. The borane‐containing polypropylene could be transformed to hydroxyl‐terminated polypropylene, PPOH. And then the polypropylene‐nylon 6 diblock copolymer, PP‐b‐NY6, was synthesized from telechelic PPOH by converting this prepolymer with toluene diisocyanate and using the resulting materials as macroactivators for anionic caprolactam polymerization. Meanwhile, this investigation used borane‐containing polypropylene and oxygen to produce free radicals at the chain end on the polypropylene. Experimental results indicate that the free radical is an effective initiator for the polymerization of methyl methacrylate to produce diblock PP‐b‐PMMA. The block copolymers are characterized by IR, NMR, and DSC analyses. The diblock copolymer is a good compatibilizer for polymer blends.     

Stress–strain behavior of low‐density polyethylene/poly(methyl methacrylate) blends with modulated interfaces with a hydrogenated polybutadiene‐block‐poly(methyl methacrylate) diblock copolymer

The stress–strain diagrams and ultimate tensile properties of uncompatibilized and compatibilized hydrogenated polybutadiene‐block‐poly(methyl methacrylate) (HPB‐b‐PMMA) blends with 20 wt % poly(methyl methacrylate) (PMMA) droplets dispersed in a low‐density polyethylene (LDPE) matrix were studied. The HPB‐b‐PMMA pure diblock copolymer was prepared via controlled living anionic polymerization. Four copolymers, in terms of the molecular weights of the hydrogenated polybutadiene (HPB) and PMMA sequences (22,000–12,000, 63,300–31,700, 49,500–53,500, and 27,700–67,800), were used. We demonstrated with the stress–strain diagrams, in combination with scanning electron microscopy observations of deformed specimens, that the interfacial adhesion had a predominant role in determining the mechanism and extent of blend deformation. The debonding of PMMA particles from the LDPE matrix was clearly observed in the compatibilized blends in which the copolymer was not efficiently located at the interface. The best HPB‐b‐PMMA copolymer, resulting in the maximum improvement of the tensile properties of the compatibilized blend, had a PMMA sequence that was approximately half that of the HPB block. Because of the much higher interactions encountered in the PMMA phase in comparison with those in HPB (LDPE), a shorter sequence of PMMA (with respect to HPB but longer than the critical molecular weight for entanglement) was sufficient to favor a quantitative location of the copolymer at the LDPE/PMMA interface. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 22–34, 2005     

Synthesis of Poly(methyl methacrylate) Labeled with Fluorescein Moieties via Atom Transfer Radical Polymerization

Fluorescein chromophore‐labeled poly(methyl methacrylate) (PMMA) was prepared via atom transfer radical polymerization (ATRP) with two novel bromine‐containing fluorescein derivatives, 3,6‐bi(2′‐bromo‐2′‐methyl‐propionic acid) fluorescein ester (Fla‐Br) and 3‐(2′‐bromo‐2′‐methyl‐propionic acid) fluorescein ester (Flb‐Br), as the functional initiators, and CuBr/PMDETA as the catalyst, respectively. The above mentioned fluorescein containing bromine were synthesized in our lab. The ATRP of PMMA was proved in a controlled fashion. The resultant PMMA with narrow molecular weight distribution was endowed with the fluorescein chromophore incorporated into the polymer backbone. The presence of the fluorescein labeling of the polymers was confirmed by ¹H‐NMR and GPC trace under UV detector. The UV spectroscopy and fluorescence measurements of the resultant polymer gave further evidence of the functionality of the fluorescein labeling.     

Poly(methyl methacrylate)‐block‐poly(N‐vinyl pyrrolidone) diblock copolymer: A facile synthesis via sequential radical polymerization mediated by isopropylxanthic disulfide and its nanostructuring polybenzoxazine thermosets

In this contribution, we reported a facile synthesis of poly(methyl methacrylate)‐block‐poly(N‐vinyl pyrrolidone) (PMMA‐b‐PVPy) diblock copolymers via sequential radical polymerizations mediated by isopropylxanthic disulfide (DIP). It was found that the radical polymerization of N‐vinyl pyrrolidone (NVP) mediated by DIP was in a controlled and living manner. In contrast, the polymerization of methyl methacrylate mediated by DIP displayed the behavior of telomerization, affording xanthate‐terminated PMMA with a good control of molecular weights while the conversion of monomer was not very high. The xanthate‐terminated PMMA can be successfully used as the macromolecular chain transfer agent for the polymerization of NVP via RAFT/MADIX process and thus PMMA‐b‐PVPy diblock copolymers can be successfully synthesized via sequential radical polymerization mediated by isopropylxanthic disulfide. One of these diblock copolymers was incorporated into polybenzoxazine and the nanostructured thermosets were obtained as evidenced by transmission electron microscopy, small angle X‐ray scattering, and dynamic mechanical thermal analysis. The formation of nanostructures in polybenzoxazine thermosets was ascribed to a reaction‐induced microphase separation mechanism. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 952–962     

The importance of proper anchoring of an amphiphilic dispersant for colloidal stability

Highly stable poly(methyl methacrylate) (PMMA) based microcapsule suspensions without excess dispersant are obtained via the solvent evaporation route using poly(methyl methacrylate)-block-poly(sodium methacrylate) or poly(methyl methacrylate)-block-poly(sodium acrylate) diblock copolymers as dispersant. The stable suspension is characterized by a high ζ-potential that does not change with time or after washing steps. It is indirectly proven on model PMMA surfaces using quartz crystal microbalance with dissipation monitoring that the PMMA block of the copolymer is embedded in the underlying PMMA microcapsule. Such anchoring of the dispersant is key for the good colloidal stability.     

Compatibilizing effect of a graft copolymer on bacterial poly(3‐hydroxybutyrate)/poly(methyl methacrylate) blends

Blends of isotactic (natural) poly(3‐hydroxybutyrate) (PHB) and poly(methyl methacrylate) (PMMA) are partially miscible, and PHB in excess of 20 wt % segregates as a partially crystalline pure phase. Copolymers containing atactic PHB chains grafted onto a PMMA backbone are used to compatibilize phase‐separated PHB/PMMA blends. Two poly(methyl methacrylate‐g‐hydroxybutyrate) [P(MMA‐g‐HB)] copolymers with different grafting densities and the same length of the grafted chain have been investigated. The copolymer with higher grafting density, containing 67 mol % hydroxybutyrate units, has a beneficial effect on the mechanical properties of PHB/PMMA blends with 30–50% PHB content, which show a remarkable increase in ductility. The main effect of copolymer addition is the inhibition of PHB crystallization. No compatibilizing effect on PHB/PMMA blends with PHB contents higher than 50% is observed with various amounts of P(MMA‐g‐HB) copolymer. In these blends, the graft copolymer is not able to prevent PHB crystallization, and the ternary PHB/PMMA/P(MMA‐g‐HB) blends remain crystalline and brittle. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1390–1399, 2002     

Diphilic Macromolecular Brushes with a Polyimide Backbone and Poly(methacrylic acid) Blocks in Side Chains

Novel macromolecular brushes with a polyimide backbone and diphilic diblock copolymer side chains consisting of a hydrophilic block of poly(methacrylic acid) adjacent to the backbone and the outer hydrophobic block of poly(methyl methacrylate) are synthesized. The synthesis includes the grafting of poly(tert-butyl methacrylate) to the polyimide chain followed by the polymerization of methyl methacrylate on the graft copolyimide as a branched multicenter macroinitiator. Brushes with diphilic side chains are obtained via the acidic hydrolysis of ester groups in the first block of side chains. The grafting polymerization of methacrylates is performed according to the “grafting from” approach by the method of pseudoliving atom transfer radical polymerization using two methodologies of polymerization activated by either copper- or iron-containing complexes. Conditions providing the controlled regime of the polymerization processes under study are found, and pathways for the targeted regulation of the degree of polymerization of methacrylate blocks and their grafting density are determined. As is shown by dynamic light scattering and transmission electron microscopy, the macromolecules of brushes with diphilic side chains form in ethanol homotypic, obviously spherical, supramolecular micellar structures with hydrodynamic radii in the range from 40 to 120 nm depending on the length and grafting density of the two blocks in diphilic side chains.     

Blends of styrene/acrylic acid copolymers and acrylic polymers

The miscibility of a series of styrene/acrylic acid copolymers with various polyacrylate and polymethacrylate homopolymers, as well as a series of styrene/methyl methacrylate copolymers, has been investigated. According to the binary interaction model, the miscibility diagram for styrene/acrylic acid copolymers with styrene/methyl methacrylate copolymers indicates that acid and ester groups interact endothermically. The phase behavior of the homopolymers also implies this. The analysis ignores the association and self-association observed for the polymer blends and the low-molecular-weight analogs used to model them. The heat of mixing of low-molecular-weight analogs depended greatly on both composition and acid structure.     

Blends of styrene/maleic anhydride copolymers with polymethacrylates

The phase behavior of a series of styrene/maleic anhydride (SMA) copolymers with various polyacrylate and polymethacrylate homopolymers has been investigated using various techniques. None of the polyacrylates are miscible with SMA copolymers. Poly (methyl methacrylate) (PMMA) poly(ethyl methacrylate) (PEMA) and poly(n-propyl methacrylate) (PnPMA), are miscible with these copolymers over a certain range of maleic anhydride contents; whereas, the higher methacrylates apparently have no region of miscibility. For PEMA and PnPMA, the miscibility windows extend through 0% MA; hence, polystyrene is miscible with these polymethacrylates although the lower critical solution temperature is quite low. The exothermic heat of mixing styrene and ester analogs found here supports the observed miscibility of polystyrene with ethyl, n-propyl, and cyclohexyl (reported elsewhere) methacrylates. Lattice fluid interaction parameters for styrene-methacrylate obtained from the cloud points of these blends agree quite well with the Flory—Huggins parameters obtained from copolymer miscibility windows.     

用双硫酯链转移法合成嵌段聚合物

研究了以双硫酯为链转移剂进行的均聚和嵌段共聚物的合成 .首先合成大分子链转移剂 ,得到分子量可控、多分散性系数较小的均聚物PMMA、PBMA、PEMA、PEA、PBA、PMA、PSt,多分散性系数一般小于 1 30 .在相同的条件下 ,甲基丙烯酸酯类的聚合速度最快 ,苯乙烯其次 ,丙烯酸酯类最慢 .用末端带有双硫酯基团的PSt、PBMA、PBA为链转移剂 ,加入多种第二单体聚合得到实测分子量与理论分子量接近 ,且多分散性系数较小的两嵌段聚合物 .在链转移剂和引发剂的比例为 3∶1～ 6∶1的范围内 ,聚苯乙烯同样可以作为第一嵌段得到和其它酯类单体的两嵌段聚合物 .1 H NMR方法证明了聚合物的末端带有双硫酯基团 .嵌段聚合时必须加入微量的自由基引发剂以形成大分子自由基 ,达到较好的控制聚合效果     

Synthesis and Characterization of a Diblock Copolymer of Methyl Methacrylate and Vinyl Acetate by Successive Photo‐Induced Charge Transfer Polymerization Using Ethanolamine as the Parent Compound

Communication: A diblock copolymer consisting of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) with hydroxyl group at one end is prepared by successive charge transfer polymerization (CTP) under UV irradiation at room temperature using ethanolamine and benzophenone as a binary initiation system. The diblock copolymer PMMA‐b‐PVAc could be selectively hydrolyzed to the block copolymer of poly(methyl methacrylate) and poly(vinyl alcohol) (PVA) using sodium ethoxide as the catalyst. Both copolymers, PMMA‐b‐PVAc and PMMA‐b‐PVA, are characterized in detail by means of FTIR and ¹H NMR spectroscopy, and GPC. The effect of the solvent on CTP and the kinetics of CTP are discussed.     

Controlling the size of nanostructures in thin films via blending of block copolymers and homopolymers

The effects of molecular weight and concentration of poly (methyl methacrylate) (PMMA) homopolymer or symmetric short polystyrene-block-poly (methyl methacrylate) (PS-b-PMMA) diblock copolymer on the size of the nanostructures of its blends with symmetric long PS-b-PMMA diblock copolymer have been investigated by atomic force microscopy. By careful controlling of the film thickness, solvent selectivity, and annealing time, PMMA cylindrical microdomains oriented normal to the film surface were obtained in all thin films. With the addition of both low- and high-molecular-weight PMMA homopolymers, the cylindrical domain sizes increased although it was less obvious for the lower molecular weight homopolymer. In contrast to the homopolymer, adding the short chain diblock copolymer resulted in a decrease in the cylindrical domain size, which was ascribed to the reduction of the interfacial tension and increase in the stretching energy.