Blends of styrene/maleic anhydride copolymers with polymethacrylates

The phase behavior of a series of styrene/maleic anhydride (SMA) copolymers with various polyacrylate and polymethacrylate homopolymers has been investigated using various techniques. None of the polyacrylates are miscible with SMA copolymers. Poly (methyl methacrylate) (PMMA) poly(ethyl methacrylate) (PEMA) and poly(n-propyl methacrylate) (PnPMA), are miscible with these copolymers over a certain range of maleic anhydride contents; whereas, the higher methacrylates apparently have no region of miscibility. For PEMA and PnPMA, the miscibility windows extend through 0% MA; hence, polystyrene is miscible with these polymethacrylates although the lower critical solution temperature is quite low. The exothermic heat of mixing styrene and ester analogs found here supports the observed miscibility of polystyrene with ethyl, n-propyl, and cyclohexyl (reported elsewhere) methacrylates. Lattice fluid interaction parameters for styrene-methacrylate obtained from the cloud points of these blends agree quite well with the Flory—Huggins parameters obtained from copolymer miscibility windows.     

Interactions in SMA-SAN blends

Styrene/maleic anhydride (SMA) and styrene/acrylonitrile (SAN) copolymers have previously been shown to form miscible blends when the MA and AN contents do not differ too greatly. It is shown here that this is the result of a weak exothermic interaction between the MA and AN units by measuring the heats of mixing for appropriate liquid analogs of the various monomer units. The region of copolymer compositions for miscibility of SMA-SAN blends is predicted from the Sanchez-Lacombe mixture theory using net interaction parameters calculated from the analog calorimetry results via a simple binary interaction model for copolymers. Lower critical solution temperature behavior was observed for blends of copolymers having compositions near the edge of the miscibility region. Various glass transition, volumetric, and FTIR results are discussed in terms of the interactions observed.     

Reactively and physically compatibilized immiscible polymer blends: stability of the copolymer at the interface

This paper reports on the interfacial behaviour of block and graft copolymers used as compatibilizers in immiscible polymer blends. A limited residence time of the copolymer at the interface has been shown in both reactive blending and blend compatibilization by preformed copolymers. Polystyrene (PS)/polyamide6 (PA6), polyphenylene oxide (PPO)/PA6 and polymethylmethacrylate (PMMA)/PA6 blends have been reactively compatibilized by a styrene-maleic anhydride copolymer SMA. The extent of miscibility of SMA with PS, PPO and PMMA is a key criterion for the stability of the graft copolymer at the interface. For the first 10 to 15 minutes of mixing, the in situ formed copolymer is able to decrease the particle size of the dispersed phase and to prevent it from coalescencing. However, upon increasing mixing time, the copolymer leaves the interface which results in phase coalescence. In PS/LDPE blends compatibilized by preformed PS/hydrogenated polybutadiene (hPB) block copolymers, a tapered diblock stabilizes efficiently a co-continuous two-phase morphology, in contrast to a triblock copolymer that was unable to prevent phase coarsening during annealing at 180°C for 150 minutes.     

Phase behavior in mixtures of a homopolymer and a block copolymer 1. FTIR and DSC studies

Miscibility in blends of three styrene-butadiene-styrene and one styrene-isoprene-styrene triblock copolymers containing 28%, 30%, 48%, and 14% by weight of polystyrene, respectively, with poly(vinyl methyl ether) (PVME) were investigated by FTIR spectroscopy and differential scanning calorimetry (DSC). It was found from the optical clarity and the glass transition temperature behavior that the blends show miscibility for each kind of triblock copolymers below a certain concentration of PVME. The concentration range to show miscibility becomes wider as the polystyrene content and molecular weight of PS segment in the triblock copolymers increase. From the FTIR results, the relative peak intensity of the 1100 cm^-1 region due to COCH₃ band of PVME and peak position of 698 cm^-1 region due to phenyl ring are sensitive to the miscibility of SBS(SIS)/PVME blends. The results show that the miscibility in SBS(SIS)/PVME blends is greatly affected by the composition of the copolymers and the polystyrene content in the triblock copolymers. Molecular weights of polystyrene segments have also affected the miscibility of the blends. ©1995 John Wiley & Sons, Inc.     

离聚物及其共混体系的研究3.基于配位络合的增容作用

通过将苯乙烯(S)与少量的甲基丙烯酸(MAA)或马来酸酐(MA)共聚及甲基丙烯酸正丁酯(nBMA)与4-乙烯基吡啶(4-VP)共聚,从而在聚苯乙烯(PS)及聚甲基丙烯酸丁酯(PBMA)链上分别引入了功能基团羧酸基(-CO-OH)、酸酐基(-CO-O-CO-)和吡啶基(-N)。通过与锌盐作用获得相应的离聚物(Ionomer)。用红外光谱(IR)表征了共聚物和离聚物的形成;差热分析(DSC)测定共聚物、离聚物和共混物的玻璃化转变温度(Tg)。研究结果表明,随着共聚物中功能基团含量的增加或者共聚物形成离聚物后,其玻璃化转变温度(Tg)提高了;而共聚物的共混物因羧酸基与吡啶基间的质子转移作用而提高了相容性。特别是在引入Zn~(2+)的共混物中,增容作用十分明显,这可归结于BMAVP中的吡啶基和SMAA-Zn~(2+)(或SMA-Zn~(2+))中的Zn~(2+)间的配位络合作用的贡献。     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.     

Blends of poly(vinyl methyl ether) with styrenic copolymers

Blends of poly(vinyl methyl ether) (PVME) with styrene/acrylonitrile (SAN), with styrene/maleic anhydride (SMA), and with styrene/acrylic acid (SAA) copolymers were examined for glass transition and lower critical solution temperature behavior. These copolymers were found to be completely miscible with PVME at levels of 3% or less of AA; below 10–11% AN, and below 15% MA (w%). Small amounts of the comonomers raised the temperature at which blends with PVME undergo phase separation on heating. This effect was greatest in the order AA > AN > MA. An interpretation of these results is given in terms of recent theories for homopolymer-copolymer blends, and the extent to which solubility parameter theory can be useful is considered.     

Characterization of the interaction energies for polystyrene blends with various methacrylate polymers

The binary interaction energies between styrene and various methacrylates were determined from newly examined phase boundaries with lattice–fluid theory. Because the blends of polystyrene (PS) and poly(cyclohexylmethacrylate) (PCHMA) were only miscible at high molecular weights when the blends were prepared by solution casting from tetrahydrofuran, we examined the miscibility of other blends by changing the molecular weights of PS or methacrylate polymers. On the basis of the phase‐separation temperature caused by the lower critical solution temperature, the miscibility of PS with the various methacrylates appeared to be in the order PCHMA > poly(n‐propyl‐methacrylate) (PnPMA) > poly(ethyl methacrylate) (PEMA) > poly(n‐butyl‐methacrylate) (PnBMA) > poly(iso‐butyl‐methacrylate) > poly(methyl methacrylate) (PMMA) > poly(tert‐butyl methacrylate), and the branching of butylmethacrylate appeared to decrease the miscibility with PS. The interaction energies between PS with various methacrylates obtained from phase boundaries with lattice–fluid theory reached minimum value corresponding to the styrene/n‐propylmethacrylate interaction. They were in the order PnPMA < PEMA < PCHMA < PnBMA < PMMA. The difference in the order of miscibility and interaction energies might be attributed to the terms related to the compressibility. The phase‐separation temperatures calculated with the interaction energies obtained here indicated that the PS/PEMA and PS/PnPMA blends at high molecular weights were miscible, whereas the PS/PnBMA blends were immiscible at high molecular weights. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2666–2677, 2000     

Degradable polymer blends. I. Screening of miscible polymers

Blends of biodegradable polymers having properties distinct from the individual polymer components, and that are suitable for use as carriers of pharmaceutically active agents, were prepared from two or more polyanhydrides, polyesters, and mixtures of polyanhydrides and low molecular weight polyesters. The blends have different properties than the original polymers, providing a mean for altering the characteristics of the polymeric matrix without altering the chemical structure of the component polymers. Aliphatic, aromatic, and copolymers of polyanhydrides were miscible in each other and formed less crystalline compositions with a single melting point which was lower than the melting point of the starting polymers. The polyesters: poly(lactide-glycolide), poly(caprolactone), and poly(hydroxybutyric acid) presented some miscibility in each other. However, the polyanhydrides were immiscible with the polyesters resulting in a complete phase separation both in solution or in melt mixing. Only low molecular weight polyesters (in the range of 2000) of lactide and glycolide, mandelic acid, propylenefumarate, and caprolactone presented some miscibility with polyanhydrides. Similarly, poly(orthoester) and hydroxybutyric acid polymers formed a uniform mixture with the anhydride polymers which had the two melting points of the original polymers. Drug release from polymer blends composed of poly(hydroxybutyric acid) or low molecular weight poly(lactic acid) with poly(sebacic anhydride) (PSA) showed a constant release of drug for periods from 2 weeks to several months as a function of the PSA content in the blend. Increasing the content of PSA, a fast degrading polymer, increases the release rate from the blend. © 1993 John Wiley & Sons, Inc.     

PVC/PBD-b-PMMA共混体系相容性的研究

采用ＤＭＡ和ＴＥＭ系统研究了聚丁二烯－聚甲基丙烯酸甲酯的嵌段共聚物（ＰＢＤ－ｂ－ＰＭＭＡ）与聚氯乙烯（ＰＶＣ）共混体系的相容性问题。结果表明：ＰＶＣ／ＰＢＤ－ｂ－ＰＭＭＡ共混体系具有部分相溶性。相容的程度与共混体系的组成、组分聚合物的分子量以及共聚物中ＰＢＤ和ＰＭＭＡ嵌段的比例密切相关。     

Study on rheological properties and relaxational behavior of poly(dianilinephosphazene)/low-density polyethylene blends

Rheological properties and relaxational behavior of blends of low-density polyethylene (LDPE) and poly(dianilinephosphazene) (PDAP) have been investigated to check miscibility and molecular relaxations in the crystalline and amorphous phases. In the studied shear rate range, all PDAP/LDPE blends exhibited a shear thinning behavior. The experimental data were fitted using the logarithmic rule and serial model to investigate the miscibility of blends. It was found that LDPE and PDAP can achieve a certain degree of miscibility in the molten state. The dynamic mechanical α-, β- and γ-relaxation behavior obtained from dynamic mechanical thermal analysis imply that the two components in the amorphous phase were miscible. The wide-angle X-ray diffraction result showed that these two components interact with each other.     

Effects of different types of polyethylene on the morphology and properties of recycled poly(ethylene terephthalate)/polyethylene compatibilized blends

Recycled poly(ethylene terephthalate) (R‐PET) was blended with four types of polyethylene (PE), linear low density polyethylene (LLDPE; LL0209AA, Fs150), low density polyethylene (LDPE; F101‐1), and metallocene‐LLDPE (m‐LLDPE; Fv203) by co‐rotating twin‐screw extruder. Maleic anhydride‐grafted poly(styrene‐ethylene/butyldiene‐styrene) (SEBS‐g‐MA) was added as compatibilizer. R‐PET/PE/SEBS‐g‐MA blends were examined by scanning electron microscopy (SEM), differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), and mechanical property testing. The results indicated that the morphology and properties of the blends depended to a great extent on the miscibility between the olefin segments of SEBS‐g‐MA and PE. Due to the proper interaction between SEBS‐g‐MA and LDPE (F101‐1), most SEBS‐g‐MA, located at the interface between two phases of PET and LDPE to increase the interfacial adhesion, lead to better mechanical properties of R‐PET/LDPE (F101‐1) blend. However, both the poor miscibility of SEBS‐g‐MA with LLDPE (LL0209AA) and the excessive miscibility of SEBS‐g‐MA with LLDPE (Fs150) and m‐LLDPE (Fv203) reduced the compatibilization effect of SEBS‐g‐MA. DSC results showed that the interaction between SEBS‐g‐MA and PE obviously affected the crystallization of PET and PE. DMA results indicated that PE had more influence on the movement of SEBS‐g‐MA than PE did. Copyright © 2010 John Wiley & Sons, Ltd.     

Graft formation and chain scission in blends of polyamide-6 and -6.6 with maleic anhydride containing polymers

The in situ formation of a compatibilizer, consisting of a copolymer of PA grafted onto a maleic anhydride (MA) containing polymer, is essential for the morphology and properties of the corresponding PA blends. In this study four blends, containing PA-6 or PA-6.6 and EPDM-g-MA or poly(styrene-co-maleic anhydride) (SMA; 28 wt % MA), were prepared and characterized. Chemical analyses showed that the amount of PA graft is independent of the blend composition. Going from EPDM-g-MA to SMA the MA content of the original MA-containing polymer increases, which in the corresponding blends results in an increase in the number of PA grafts and a decrease in the length of the PA grafts. In the SMA blends the number averaged molecular weight of the grafted PA is only about 200 g/mol. It is postulated that the water molecule, released upon imide formation at the PA/(MA-containing polymer) interface, hydrolyses a PA amide group, resulting in a new amine end group, which in its turn reacts with the MA-containing polymer, etc. Differential scanning calorimetry shows that the degree of crystallinity of the PA phase is decreased only when the size of the PA phase between the MA-containing polymer domains approaches the PA crystalline lamellar thickness. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 179–188, 1998     

Miscibility of polysulfone blends with poly(1‐vinylpyrrolidone‐co‐styrene) copolymers and their interaction energies

The miscibility of polysulfone (PSf) with various hydrophilic copolymers was explored. Among these blends, PSf gave homogeneous mixtures with poly(1‐vinylpyrrolidone‐co‐styrene) [P(VP–S)] copolymers when these copolymers contained 68–88 wt % 1‐vinylpyrrolidone (VP). Miscible PSf blends with P(VP–S) copolymers underwent phase separation on heating caused by lower critical solution temperature (LCST)‐type phase behavior. The phase behavior depended on the copolymer composition. Changes in the VP content of P(VP–S) copolymers from 65 to 68 wt % shifted the phase behavior from immiscibility to miscibility and the LCST behavior. The phase‐separation temperatures of the miscible blends first increased gradually with the VP content, then went through a broad maximum centered at about 80 wt % VP, and finally decreased just before the limiting content of VP for miscibility with PSf. The interaction energies of binary pairs involved in PSf/P(VP–S) blends were evaluated from the phase‐separation temperatures of PSf/P(VP–S) blends with lattice‐fluid theory combined with a binary interaction model. The decrease in the contact angle between water and the membrane surface with increasing VP content in P(VP–S) copolymers indicated that the hydrophobic properties of PSf could be improved via blending with hydrophilic P(VP–S) copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1401–1411, 2003     

Ion transport and relaxation in phosphonium poly(ionic liquid) homo- and co-polymers

In the present work, a poly(ionic liquid) (PIL), poly(triphenyl-4-vinylbenzylphosphonium chloride) and a series of its random copolymers with nonionic hydrophobic poly(methyl methacrylate) (PMMA) are synthesized by conventional free radical polymerization (CFRP) and reversible addition-fragmentation chain-transfer (RAFT) polymerization. The understanding of some fundamental aspects about ion transport and relaxation mechanism in PIL and PIL copolymers are investigated using dielectric spectroscopy via several theoretical models. The influence of copolymer compositions, physical blending of neat PIL and PMMA, size of counter anions (Cl⁻ and TFSI⁻) and variation of molecular weights on thermal stability, moisture sensitivity, ionic transport and relaxation properties are also studied. An enhancement of thermal stability and ionic transport property of the PIL copolymer is observed compared to those of the physically mixed blend of two homopolymers with same compositions. The incorporation of hydrophobic PMMA segment definitely decreases the moisture content in PIL copolymers than the PIL itself. In all these PIL- based systems, the temperature dependence of ionic conductivity, relaxation time and ion diffusivity are well described by Vogel-Tammann-Fulcher model. The studies of some fundamental properties of these new PIL copolymers with less moisture sensitivity may help in using them as potential polymer electrolytes in energy storage devices.     

Transition from miscibility to immiscibility in blends of poly(methyl methacrylate) and styrene-acrylonitrile copolymers with varying copolymer composition: a DSC study

The glass transition and the structural relaxation processes have been studied in blends of poly(methyl methacrylate) (PMMA) and styrene-acrylonitrile (SAN) copolymers with different acrylonitrile (AN) contents. The 50/50 wt.% blend of PMMA with the SAN copolymer containing 30 wt.% of AN is immiscible, while blends with copolymers containing between 13 and 26 wt.% of AN are miscible. Thus the upper limit of miscibility is between 26 and 30 wt.% of AN. The temperature dependence of the relaxation times of the conformational rearrangements of polymer chains around the glass transition have been determined in the blends and pure components by modelling DSC thermograms obtained after different thermal histories in each sample. The slope in the Arrhenius diagram logτ vs 1/T around the glass transition temperature is significantly smaller in the blend which is closer to the upper limit of miscibility than in the other miscible blends in which SAN copolymer contains less AN. The change of slope can be ascribed to a distribution in the glass transition temperatures of the different rearranging regions, reflecting the appearance of a microheterogeneity in the blend that cannot be detected as a double glass transition in the blend.     

Interfacial thickness in bilayers of poly(phenylene oxide) and styrenic copolymers

Estimates for the thickness of the interface between poly (2,6-dimethyl-1,4-phenylene oxide) (PPO) and copolymers of styrene–acrylonitrile (SAN) and styrene–maleic anhydride (SMA) based on the theory of Helfand and Tagami are compared to neutron reflectivity (NR) measurements. Good agreement is found between the NR measurements and theoretical predictions that make use of a mean field binary interaction model and previously reported binary interaction energies. The techniques outlined in this work may be used to understand relationships between the mechanical properties of multiphase polymer blends and the fundamental thermodynamics of polymer interactions. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 3115–3125, 1998     

Synthesis and Characterization of a Branched Poly(Methacrylamide): Thermal Stability and Molecular Simulation Studies of Their Blends With Vinylic Polymers

The synthesis of a poly(diethylaminoethyl methacrylamide) (BP), based on a lineal methacrylamide with diethylaminoethyl branches was carried out. Thermal behavior was studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Relatively high thermal stability is found. Blends with poly(methylmethacrylate) (PMMA), poly(acrylic acid) (PAA) and poly(monomethyl itaconate) (PMMI) were prepared. Their thermal properties in blends were studied together with miscibility, in order to improve thermal properties of vinylic polymer blends. An increase of thermal stability was found for certain blend compositions. By FTIR analysis, higher band displacements were found for low BP compositions. AFM and molecular simulation analysis were carried out in order to elucidate the structural origin leading to thermal stability and miscibility increases. Hydrophobic interactions among methyl end groups of BP and methylene groups of vinylic polymers should be the responsible of miscibility and thermal stability increases.     

HIPS／MA接技共聚物对HIPS／PA1010共混体系的增容

制备了高抗冲聚苯乙烯和马来酸酐的接枝共聚物，利用红外光谱，电子能谱和动态力学谱对产物的结构进行了表征，并通过滴定法测定了接枝物中马来酸酐的含量。结果表明马来酸酐接技到了高抗冲聚苯乙烯中顺丁橡胶的分子链上，接技率为４．７％。研究了该接枝共聚物对ＰＡ１０１０／ＨＩＰＳ共混物的增容作用。电镜照片显示，随着共聚物中接枝物含量的增加，分散相相区尺寸明显减小，说明增容效果显著。测定了共混体系的拉伸行为，研究了