A W-band Frequency Source with Low Spurs and Low Phase Noise

A W-band millimeter wave frequency source is developed by frequency multiplier chain and injection locking. The referenced crystal oscillator (CO) signal 120 MHz is multiplied 400 times to output 48 GHz signal. Then, it is used as a referenced source of fundamental-wave injection-locked harmonic Gunn oscillator with output power more than 10 mW at 96 GHz and spurious output less than −65 dBc. The measured phase noise is −97 and −105 dBc/Hz at 10 kHz and 200 kHz offset, respectively. At last, the influence of the flicker noise, provided by the frequency multipliers and amplifiers, is analyzed.     

35 GHz dielectric resonator stabilised gunn oscillator

A 35 GHz dielectric resonator oscillator(DRO) using GaAs Gunn diode in microstrip configuration has been designed and developed. The oscillator, with an integral waveguide-to-microstrip transition, delivered an output greater than 18 dBm. Phase noise of the oscillator is found to be better than –80 dBc/Hz at 100 KHz away from the carrier. A frequency drift of about ±25 MHz has been observed over the temperature range from –10 °C to 50 °C.     

A dual band CMOS VCO with a balanced duty cycle buffer

This paper proposes a dual band VCO with a standard 0.35 μm CMOS process to generate 1.07 and 2.07 GHz. The proposed VCO architecture with 50% duty cycle circuit and a half adder (HA) is able to produce a frequency two times higher than that of the conventional VCOs. The measurement results demonstrate that the gain of VCO and power dissipation are 561 MHz/V and 14.6 mW, respectively. The phase noises of the dual band VCO are measured to be −102.55 and −95.88 dBc/Hz at 2 MHz offset from 1.07 and 2.07 GHz, respectively.     

高性能注入锁相光电振荡器

提出一种基于注入锁定和锁相环技术的注入锁相光电振荡器.利用注入锁定来改善光电振荡器的近载频相噪以及杂散抑制度.将光电振荡器的输出信号与外注入源进行鉴相,通过锁相环来提升频率稳定性,并进一步改善光电振荡器的近载频相噪.实验结果表明:注入锁相光电振荡器在电滤波器中心频率为9.5GHz、3dB带宽为20 MHz和光纤环长度为6km的情况下,实现了输出信号频率为9.5GHz的单模振荡;当注入锁定带宽为1.98kHz时,光电振荡器输出信号在1kHz频偏处的相位噪声为-125dBc/Hz,在10kHz频偏处的相位噪声为-147dBc/Hz,杂散抑制度高于80dB,阿伦偏差接近1.37×10~(-11)@1s和1.22×10~(-11)@1000s.     

长光纤环高性能光电振荡器研究

提出了采用多个长光纤环实现高性能光电振荡器的方法,通过合理的长度设计,多个长光纤环能够降低光电振荡器的相位噪声,同时提高边模抑制比。理论分析了多个长光纤环实现高性能光电振荡器的可行性,并构建了实验系统。在实验中,利用3个大于4km的长光纤环构建光电振荡器,实现了频率10GHz的微波信号,其相位噪声在频偏10kHz处达到了-130dBc/Hz,边模抑制比达到了60dBc。实验结果与理论分析一致,证明了该方法的正确性。     

C波段低相位噪声高温超导介质振荡器

高温超导技术在现代军用、民用电子系统中的应用日益广泛,文中的设计应用超导技术制作了一个振荡器,该振荡器具有极低的相位噪声,在77K温区,该振荡器工作频率5.012GHz,偏离载频1kHz处相位噪声达-129.8dBc/Hz.     

Two-level injection in fiber-delay line based oscillator

Two-level injection-locked opto-electronic oscillator is proposed for low phase noise. Dielectric resonator oscillator (DRO) is used as the first injection source, injection locking a long-fiber loop based opto-electronic oscillator, then its output is injection locking another long-fiber opto-electronic oscillator for getting a lower-phase noise output carrier. After the first injection, the single side band (SSB) phase noise at 10 kHz offset frequency decreases from −123 dBc/Hz to −135 dBc/Hz, then through the second injection the SSB phase noise drops down to −146 dBc/Hz.     

Subfemtosecond synchronization of microwave oscillators with mode-locked Er-fiber lasers

We synchronize an 8.06 GHz microwave signal from a voltage-controlled oscillator with an optical pulse train from a 77.5 MHz mode-locked Er-fiber laser using a fiber-based optical-microwave phase detector. The residual phase noise between the optical pulse train and the synchronized microwave signal is -133 dBc/Hz (-154 dBc/Hz) at 1 Hz (5 kHz) offset frequency, which results in 838 as integrated rms timing jitter [1 Hz-1 MHz]. The long-term residual phase drift is 847 as (rms) measured over 2 h, which reaches 4×10(-19) fractional frequency instability at 1800 s averaging time. This method has a potential to provide both subfemtosecond-level short-term phase noise and long-term phase stability in microwave extraction from mode-locked fiber lasers.     

Frequency Sources in W-band Radar Front-end with Low Phase Noise

A W-band coherent stepped-frequency pulsed radar front-end is developed. It consists of a millimetre wave transmitting source, a mm-wave local source, a DDS with multi frequency points output and two microwave sources serving as local oscillators. All the sources are coherent with the 120 MHz referenced crystal oscillator. The mm-wave sources are realized by frequency multiplier chain, up-conversion and injection locking. The phase noise of fundamental-wave injection-locked W-band harmonic Gunn oscillator output signal achieves −98 dBc/Hz at 10 kHz offset and the spurious output is less than −50 dBc. The received intermediate frequency signal is also presented.     

Optical-fiber pulse rate multiplier for ultralow phase-noise signal generation

In this Letter we report on an all optical-fiber approach to the synthesis of ultralow-noise microwave signals by photodetection of femtosecond laser pulses. We use a cascade of Mach-Zehnder fiber interferometers to realize stable and efficient repetition rate multiplication. This technique increases the signal level of the photodetected microwave signal by close to 18 dB. That in turn allows us to demonstrate a residual phase-noise level of -118 dBc/Hz at 1 Hz and -160 dBc/Hz at 10 MHz from a 12 GHz signal. The residual noise floor of the fiber multiplier and photodetection system alone is around -164 dBc/Hz at the same offset frequency, which is very close to the fundamental shot-noise floor.     

A novel tunable optical oscillator for broadband signals

A tunable optical oscillator that generates signals at the micro- to millimeter-wave band for wireless communication applications is suggested. It uses directly modulated semiconductor lasers, in which sideband modes and four-wave mixing (FWM) conjugate modes are injection locked by the simple control of the applied modulation power. The signals at 15 GHz with phase noise of below ?95 dBc/Hz at an offset frequency of 100 kHz were experimentally obtained. The frequency of the generated signal is tunable, and the maximum achievable signal frequency is limited mainly by the bandwidth of the receiver.     

Coupled frequency-doubling optoelectronic oscillator based on polarization modulation and polarization multiplexing

A coupled frequency-doubling optoelectronic oscillator (OEO) is proposed and experimentally demonstrated, which is constructed based on the perfect combination of polarization modulation and polarization multiplexing. A fundamental microwave signal at 9.95 GHz or a frequency-doubled microwave signal at 19.9 GHz is generated with a wavelength-independent sidemode-suppression ratio (SMSR) as high as 78 dB obtained. The phase noise of the generated 19.9-GHz signal is ? 103.45 dBc/Hz at 10-kHz frequency offset, indicating a good short-term stability. The proposed scheme is simple and flexible, which can find applications in radars and wireless communications.     

A Novel W-band Microstrip Integrated Avalanche Diode High Order Frequency Multiplier

A W band microstrip integrated high order frequency multiplier based on avalanche diode is proposed. The property of avalanche high order multiplication mode is analyzed based on physical operation mechanism of avalanche diode. According to the harmonics impedance model of avalanche diode, the microstrip integrated multiplier is designed, fabricated and measured. Output power of 5.78 mW has been obtained at output frequency of 94.5 GHz with 15th multiplication order and the phase noise is -90 dBc/Hz and -95 dBc/Hz at 10 KHz and 100 KHz offset. Good results at 13th and 17th multiplication order are also obtained.     

Ultralow phase noise microwave generation with an Er:fiber-based optical frequency divider

We present an optical frequency divider based on a 200 MHz repetition rate Er:fiber mode-locked laser that, when locked to a stable optical frequency reference, generates microwave signals with absolute phase noise that is equal to or better than cryogenic microwave oscillators. At 1 Hz offset from a 10 GHz carrier, the phase noise is below -100 dBc/Hz, limited by the optical reference. For offset frequencies >10 kHz, the phase noise is shot noise limited at -145 dBc/Hz. An analysis of the contribution of the residual noise from the Er:fiber optical frequency divider is also presented.     

用于铯芯片级原子钟的4.596 GHz射频源研制

芯片级原子钟主要包括射频模块、物理封装模块以及其他的外围控制模块。射频模块的设计关系到芯片级原子钟的短期稳定度,所以射频模块在芯片级原子钟的设计时是非常重要的一部分。本文利用数字锁相环技术实现频率为4.596 GHz的射频源,射频源由三部分组成,包括小数分频频率综合器、压控振荡器和环路滤波器。数字锁相环具有相位噪声低,频谱稳定度高等特点。此外,由于小数分频频率综合器是可编程的,可以通过配置N分频器与R分频器实现输出频率的快速扫描。与此同时,根据相关公式,可以计算出三阶无源环路滤波器的近似参数值,所设计的环路滤波器具有300 kHz的环路带宽以及55的相位裕度。最后,整个基于数字锁相环技术实现的射频源通过仿真、硬件实现以及测试。测试结果显示,射频源的相位噪声为-74.02 dBc/Hz@300 Hz,符合芯片级原子钟射频源的设计要求。     

Q-band injection-locked gunn diode oscillator

The configuration and performance of a Q-band injection-locked Gunn oscillator are presented whose outport is connected with a phase-locked reference source by a circulator. The output power of the oscillator is more than 60mW at 46.1GHz. The single-sideband phase noise (SSB) is less than-71.7dBc/Hz offset 10KHz from the carrier, and the spectrum of clutter signal is less than -40dB.     

基于DFB腔注入锁定效应的可调谐光电振荡器

提出一种基于分布反馈光注入锁定效应的可调谐光电振荡器,其环路主要由马赫曾德尔调制器、光电探测器、环形器、分布反馈激光器和射频放大器顺接而成,分布反馈激光器是系统关键器件,通过分布反馈激光器光注入锁定效应,分布反馈腔在光域实现了微波光子滤波器功能,无需传统光电振荡器必须的射频带通滤波器.同时,由于分布反馈激光器注入锁定提高了环路Q值,因此系统可采用短环路结构,从而降低了光纤因温度敏感对微波信号稳定性的影响并减小了整个系统的尺寸.另外,通过调节注入光波长和功率可改变该微波光子滤波器的中心频率,从而可实现系统的可调谐性.理论分析了该光电振荡器的原理和微波光子滤波器的调谐性,在此基础上开展了实验验证.结果表明该光电振荡器能够产生18.7～21.6 GHz的可调微波信号,在1 kHz频偏处的相位噪声为-90 dBc/Hz.     

Ultra-stable microwave generation with a diode-pumped solid-state laser in the 1.5-μm range

We demonstrate the first ultra-stable microwave generation based on a 1.5-μm diode-pumped solid-state laser (DPSSL) frequency comb. Our system relies on optical-to-microwave frequency division from a planar-waveguide external cavity laser referenced to an ultra-stable Fabry–Perot cavity. The evaluation of the microwave signal at ~10 GHz uses the transportable ultra-low-instability signal source ULISS^®, which employs a cryo-cooled sapphire oscillator. With the DPSSL comb, we measured ?125 dBc/Hz phase noise at 1 kHz offset frequency, likely limited by the photo-detection shot-noise or by the noise floor of the reference cryo-cooled sapphire oscillator. For comparison, we also generated low-noise microwave using a commercial Er:fiber comb stabilized in similar conditions and observed >20 dB lower phase noise in the microwave generated from the DPSSL comb. Our results confirm the high potential of the DPSSL technology for low-noise comb applications.     

HL-2Mװ��LHCDϵͳ3.7GHz΢������Դ���

介绍了HL-2M装置低混杂波系统中3.7GHz微波激励源的设计。微波激励源设计为模块化形式,由3.7GHz点频固态源单元、功率分配器单元、功率放大器单元和现场控制器单元等组成。微波激励源有8路输出端口,每个端口的输出功率在0~10W范围内连续可调,并可以实现远程控制输出功率;采用取样鉴相锁相环技术使微波输出信号具有相位噪声低、频率稳定度高、杂散抑制好等优点。频偏1kHz时,相位噪声是-115dBc/Hz,频偏10kHz时,相位噪声是-117dBc/Hz,频偏100kHz时,相位噪声是-122dBc/Hz;输出频率稳定度≤0.03ppm/30min;杂散抑制≤-80dBc。     

Ultralow-noise mode-locked laser with coupled optoelectronic oscillator configuration

We describe simultaneous generation of ultralow-noise optical pulses and microwave signal with a mode-locked fiber laser in a coupled optoelectronic oscillator configuration. We demonstrate 9.2-GHz optical and microwave signals with the measured phase noise of -140 dBc/Hz at 10-kHz offset frequency. We show that the mode-locked laser in the photonic oscillator serves as a high-Q filter and is responsible for the observed low phase noise.