聚磷酸酯阻燃剂复配聚磷酸铵对环氧树脂阻燃性能的影响

合成了一种9,10-二氢-9-氧杂-10-磷杂菲-10-氧化物(DOPO)的衍生物——聚苯氧基磷酸-2-10-氢-9-氧杂-磷杂菲基对苯二酚酯(POPP), 以间苯二胺(m-PDA)为固化剂, 环氧树脂(EP)为基料, POPP为阻燃剂, 复配聚磷酸铵(APP), 制备了不同磷含量的阻燃环氧树脂. 利用极限氧指数(LOI)和垂直燃烧(UL94)实验表征了环氧树脂的阻燃性能; 以热重分析、 锥型量热和扫描电镜分析了阻燃环氧树脂的热性能和表面形态. 研究结果表明, 阻燃剂总加入量(质量分数)为5%时即可达到UL94 V-0级, 同时LOI值为27.7%; 当总加入量为15%, 即w_POPP=5%, w_APP=10 %时, 其LOI值可达到33.8%. 随着磷含量的增加, 阻燃环氧树脂的初始降解温度略有降低, 但高温下的残炭率明显增加. POPP/APP的加入在很大程度上降低了环氧树脂的热释放速率、 有效燃烧热、 烟释放量和有毒气体释放量. 阻燃环氧树脂在高温下形成比较稳定的致密膨胀炭层, 为底层的环氧树脂主体隔绝了分解产物及热量和氧气交换, 增强了高温下的热稳定性.     

膨胀阻燃硬质聚氨酯泡沫塑料热降解及燃烧产烟研究

采用热失重、X-射线光电子能谱分析、氧指数及烟密度测试等方法研究了可膨胀石墨(EG)与聚磷酸铵(APP)复配膨胀阻燃硬质聚氨酯泡沫塑料(RPUF)的热降解、燃烧性能及产烟行为.在此基础上利用锥形量热仪考察了EG/APP对磷酸三(β-氯异丙基)酯(TCPP)阻燃RPUF体系燃烧性能的影响.研究表明,EG与APP间的相互作用导致了EG/APP体系高温阶段失重速率下降、残炭量显著上升;EG/APP与RPUF之间的成炭作用以APP的化学成炭为主.与RPUF比较,RPUF/EG/APP的氧指数由19.8%提高至35.4%的同时,烟密度没有显著上升.对比EG、APP及EG/APP阻燃RPUF,体系残炭量越高、炭层耐热氧化能力越强,氧指数就越大;残炭表面越致密,产烟量就越少.添加EG/APP可显著降低含卤体系RPUF/TCPP的热释放、烟释放及CO释放速率,体现了EG与APP复合体系物理与化学膨胀结合的优势.     

OMMT-NC-膨胀型阻燃剂三元协同阻燃LLDPE的效果

采用有机蒙脱土(OMMT)和碳酸镍(NC)为阻燃协效剂,与膨胀型阻燃剂(IFR)三元体系协同阻燃线性低密度聚乙烯(LLDPE).采用热重分析(TGA)、氧指数(LOI)测试、UL-94燃烧测试和锥形量热测试(CONE)研究了LLDPE阻燃体系的热稳定性和燃烧性能;采用红外光谱分析(FT-IR)、数码相机和扫描电子显微镜(SEM)对燃烧残余物的结构和形貌进行了分析.结果表明:固定mnLLDPE/mIFR=7/3,当moMMT/m(LLDPE+IFR)=0.04时,阻燃体系的LOI为31.5％,通过UL-94 V-0级测试,LLDPE-IFR-OMMT的残炭率为15.09％,最大热释放速率(PHRR)相比于纯LLDPE降低了50％;向LLDPE-IFR-OMMT体系中添加NC,少量的NC就能显著增加体系的阻燃性能,当mNC/m(LLDPE+IFR)=0.02时,阻燃体系的LOI为32.7％,LLDPE-IFR-OMMT-NC的残炭率达到19.04％,PHRR相比于纯LLDPE降低了57％.OMMT和NC的加入能催化LLDPE-IFR成炭,形成致密的炭层,增加炭层的强度,从而提高复合材料的阻燃性能.     

聚苯氧基磷酸联苯二酚酯/聚磷酸铵膨胀阻燃剂对环氧树脂阻燃性能影响研究

以聚苯氧基磷酸联苯二酚酯(PBPP)与聚磷酸铵(APP)组成复合阻燃剂,对环氧树脂(EP)进行阻燃改性.通过氧指数(LOI)、垂直燃烧(UL-94)、热失重(TGA)、锥形量热(CONE)和扫描电镜(SEM)等方法研究改性环氧树脂的阻燃性能和阻燃机理.结果表明,PBPP/APP体系对EP具有较好的阻燃性能,阻燃剂添加量为10%时能使环氧树脂的氧指数提高到29.6%,垂直燃烧等级达到UL94 V-0级,残炭量大大增加;平均热释放速率下降45.7%,热释放速率峰值下降51.0%,有效燃烧热平均值下降21.1%;TGA、CONE、SEM等综合分析显示了PBPP/APP改性后的环氧树脂比纯环氧树脂具有更高的热稳定性,燃烧后能够形成连续、致密、封闭、坚硬的焦化炭层,在聚合物表面产生有效覆盖、隔绝了氧气,改善了环氧树脂的燃烧性能.     

DOPO基膦酸铝盐的制备及其阻燃环氧树脂的性能研究

以10-羟基-9-氧杂-10-磷杂菲-10-氧化物(DOPO-OH)和六水合氯化铝为原料合成了一种DOPO基膦酸铝盐(DOPO-Al)阻燃剂,通过红外光谱、扫描电镜、能谱、核磁共振磷谱和热失重表征了其结构,并制备了DOPO-Al阻燃的环氧树脂,通过极限氧指数、锥形量热、热失重和差示扫描量热测试分析了该树脂的阻燃和热性能。结果表明,DOPO-Al为高温阻燃剂,其初始热分解温度(T_(5%))高达595.5℃。DOPO-Al能提高环氧树脂的阻燃性能和耐热性。当DOPO-Al添加量为7.5%(wt)时,环氧树脂的LOI值由24.1%提高至31.3%;在燃烧过程中,使其热释放速率峰值、平均热释放速率、总热释放、总烟释放和总烟产量均降低,使残留物增加幅度高达135%。炭层分析表明DOPO-Al存在凝聚相阻燃机理。环氧树脂的T_(5%)和玻璃化转变温度分别高达368.9℃和161.8℃,所制备阻燃环氧树脂具有较好的热性能。     

耐高温杂化阻燃剂/改性红磷阻燃半芳香尼龙的研究

将自制的耐高温勃姆石@苯基次膦酸铝杂化阻燃剂(BM@Al-PPi)与市售改性红磷(MRP)复配制得一种可用于半芳香尼龙PA6T/DT(HTN)的耐高温高效阻燃体系.保持阻燃剂15 wt%的总添加量不变时,MRP的添加量仅为5 wt%即可赋予HTN垂直燃烧V-0级别,极限氧指数为29.8%.锥形量热测试及其燃烧残余物研究表明,MRP阻燃HTN材料以气相阻燃作用为主,抑制热释放效果不佳且烟释放明显增加;而BM@Al-PPi的凝聚相交联成炭作用可同时抑制热释放与烟释放.结合裂解气相色谱质谱联用(Py-GC-MS)分析,给出了HTN/BM@Al-PPi/MRP体系的阻燃机理.BM@Al-PPi与MRP结合使得残炭质量显著提高,同时兼具气相作用,达到了较好的阻燃效果.     

核壳型纳米粒子填充PP-EVA及阻燃材料的动态燃烧行为

利用锥形量热仪(CONE)和热重分析(TGA),并结合极限氧指数(LOI)和UL-94垂直燃烧测试方法对核(PSt/OMMT)-壳(PBA)结构纳米复合粒子(CSN)填充聚丙烯(PP)-乙烯-醋酸乙烯酯共聚物(EVA)复合材料及加入无卤复配阻燃剂制备的PP-EVA/CSN/聚磷酸铵(APP)/层状氢氧化镁铝(LDH)复合阻燃材料的阻燃性能及热降解行为进行了研究。结果表明,添加10%(wt)CSN可以提高PP-EVA复合材料的阻燃性能,且PP-EVA复合体系燃烧时的热释放速率、有效燃烧热减少,热稳定性增强。CSN与APP/LDH产生阻燃协同作用,使复合阻燃材料的阻燃性能、热稳定性能进一步提高。     

三聚氰胺聚磷酸盐/季戊四醇配比、协效剂组及表面改性对聚丙烯基木塑复合材料的膨胀阻燃影响

通过极限氧指数(LOI)、线性燃烧速率(LBR)、热重分析和锥形量热分析等技术手段研究膨胀型阻燃剂(IFRs)中三聚氰胺聚磷酸盐(MPP)和季戊四醇(PER)的质量比、组成为m(MgO):m(可膨胀石墨,EG):m(SiO₂)=1:5:5的协效剂组(MgO/EG/SiO₂)和硅烷偶联剂(KH550)对聚丙烯基木塑复合材料(WPC)阻燃性能的影响。 结果表明,当IFRs中m(MPP):m(PER)=23:2(IFRs-M1)、质量分数为25%时的阻燃性能最佳,膨胀阻燃复合材料WPC/IFRs-M1的LOI和LBR分别为27.1%和3.89 mm/min,较未添加的WPC分别提高48.1%和下降89.79%,燃烧时的热释放速率、总热释放量、总烟释放量和CO₂释放量分别降低了76.2%、50.1%、6.9%和65.4%,600 ℃时的残炭率提高了498.3%。 协效剂组和KH550表面处理均可进一步改善WPC/IFRs-M1的阻燃性能,均对IFRs-M1具有良好的阻燃增效作用。 相比于WPC/IFRs-M1,同时用这两种阻燃增效手段的WPC/IFRs-M1/MgO/EG/SiO₂/KH550,其LOI提高了3.7%,LBR降低了20.3%;材料的热稳定性明显提高,热失重降低;燃烧时的热释放速率、总热释放量、总烟释放量和CO₂释放量分别降低了36.5%、37.6%、57.5%和33.33%,600 ℃时的残炭率提高了84.02%,显示出二者更好的协同效应。     

PP/EVA/OMMT纳米复合材料及其阻燃材料的动态燃烧行为

利用锥形量热仪(CONE)在35kW/m2热辐照条件下,并结合极限氧指数(LOI)和UL-94垂直燃烧测试方法对聚丙烯(PP)/乙烯-醋酸乙烯酯共聚物(EVA)/有机蒙脱土(OMMT)纳米复合材料和加入无卤复配阻燃剂制备的PP/EVA/OMMT/氢氧化铝(ATH)/三氧化二锑(AO)纳米复合阻燃材料的热释放速率、烟释放及材料在燃烧时的质量损失行为进行了研究。结果表明,添加5%(质量分数)OMMT可以提高PP/EVA复合材料的阻燃性能,燃烧时的热释放速率、质量损失率以及烟释放量减少,且OMMT与无卤复配阻燃剂之间可产生阻燃协同作用,使纳米复合阻燃材料的阻燃性能、热稳定性和抑烟性进一步增强。     

膨胀型无卤阻燃HIPS热分解动力学及阻燃机理研究

利用动态热失重法(TGA)研究了一种新型的膨胀型无卤阻燃高抗冲聚苯乙烯(HIPS)热降解反应动力学及阻燃机理, 通过对Kissinger模型和Coat-Redern (C-R)模型求解的热降解反应的动力学参数对比, 最终确定反应的动力学参数. 其中, 反应级数n的确定是通过一般反应对Ea/RTmax取值范围的限定, 利用最大热降解速率所对应的失重率αmax与n的关系, 确定其取值. 并采用TGA-FTIR及Py-GC/MS对材料气相产物及热裂解产物进行了阻燃机理的研究. 研究表明, 两种反应的热降解反应动力学参数基本一致, 其中阻燃HIPS的平均表观活化能小于纯HIPS, 说明在HIPS分解之前, 无卤阻燃剂已经开始分解, 释放的难燃气体(氨气及其衍生物、水蒸气等)在气相中起到阻燃的作用. 同时阻燃剂的添加, 促使反应向链转移反应飘移, 使燃烧产物中非单体化合物增加, 而在凝聚相中形成的致密的炭层结构也起到阻燃的效果.     

Flame retardant effects of organic inorganic hybrid intumescent flame retardant based on expandable graphite in silicone rubber composites

In this work, an organic inorganic hybrid intumescent flame retardant (functionalized expandable graphite, FEG) was synthesized and characterized by Fourier transform infrared spectrometry (FTIR). The flame retardant effects of FEG in silicone rubber (SR) composites were investigated by cone calorimeter test (CCT), and the thermal stability of SR composites was studied using TGA. The CCT results showed that FEG can effectively reduce the flammable properties including peak heat release rate (PHRR), total heat release (THR), smoke production rate (SPR), total smoke release (TSR), and smoke factor (SF). An improvement of thermal stability of SR/FEG was also observed. Compared with EG, FEG can further reduce THR, SPR, and TSR of SR/FEG composites in combustion process. Moreover, there is a more obvious intumescent char layer formed from the sample with FEG than the sample with EG at the same loading in SR composites. Copyright © 2014 John Wiley & Sons, Ltd.     

The synergistic flame‐retardant effect of O‐MMT on the intumescent flame‐retardant PP/CA/APP systems

The flame retardancy of a novel intumescent flame‐retardant polypropylene (IFR‐PP) system, which was composed of a charring agent (CA), ammonium polyphosphate (APP), and polypropylene (PP), could be enhanced significantly by adding a small amount (1.0 wt%) of an organic montmorillonite (O‐MMT). The synergistic flame‐retardant effect was studied systematically. The thermal stability and combustion behavior of the flame‐retarded PP were also investigated by thermogravimetric analysis (TGA), limiting oxygen index (LOI), vertical burning test (UL‐94), scanning electronic microscopy (SEM), and cone calorimeter test (CCT). TGA results demonstrated that the onset decomposition temperatures of IFR‐PP samples, with or without O‐MMT, were higher than that of neat PP. Compared with IFR‐PP, the LOI value of IFR‐PP containing 1.0 wt% O‐MMT was increased from 30.8 to 33.0, and the UL‐94 rating was also enhanced to V‐0 from V‐1 when the total loading of flame retardant was the same. The cone calorimeter results showed that the IFR‐PP with 1.0 wt% of O‐MMT had the lowest heat release rate (HRR), total heat release (THR), total smoke production (TSP), CO production (COP), CO₂ production (CO₂P), and mass loss (ML) of all the studied IFR‐PP samples, with or without O‐MMT. All these results indicated that O‐MMT had a significantly synergistic effect on the flame‐retardancy of IFR‐PP at a low content of O‐MMT. Copyright © 2009 John Wiley & Sons, Ltd.     

Flame retardancy and thermal degradation of halogen-free flame-retardant biobased polyurethane composites based on ammonium polyphosphate and aluminium hypophosphite

In this work, based on castor oil (CO), flame retardant polyurethane sealants (FRPUS) with ammonium polyphosphate (APP) and aluminum hypophosphite (AHP) were prepared. The synergistic flame retardant effects between APP and AHP on flame retardancy, thermal stability, and flame retardant mechanisms of FRPUS were investigated. It was found that when the mass ratio of APP and AHP was 5:1, the limiting oxygen index (LOI) value of FRPUS increased to 35.1%, In addition, at this ratio, the parameters from cone calorimeter testing (CCT) were reduced; these parameters include peak heat release rate (PHRR), total heat release (THR), smoke production rate (SPR) and total smoke production (TSP). The thermal decomposition behavior of the FRPUS was investigated by thermogravimetric analysis (TGA). The results showed that AHP improved the thermal stability of the PUS/APP system and increased char residue at high temperatures. Moreover, the residual carbon was investigated by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM), gas phase pyrolysis products were investigated by thermogravimetric analysis/infrared spectrometry (TG-IR) and thermogravimetric analysis/mass spectrometry (TG-MS). It was observed that the flame retardant mechanisms of the APP/AHP system was the combination of gas and condensed phase flame retardant mechanisms.     

Synthesis of DOPO‐based pyrazine derivative and its effect on flame retardancy and thermal stability of epoxy resin

A novel DOPO‐based pyrazine derivative 6‐((2‐hydroxyphenyl)(pyrazin‐2‐ylamino)methyl)dibenzo[c,e][1,2]oxaphosphinine 6‐oxide (DHBAP) was triumphantly synthesized by a two‐step addition reaction using 2‐aminopyrazine, 2‐hydroxybenzaldehyde and 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide (DOPO) as reactants, and characterized by Fourier‐transform infrared (FTIR), ³¹P nuclear magnetic resonance (NMR) and ¹H NMR. Afterwards, the addition type flame retardant (DHBAP) was utilized to modify epoxy resin (EP) by blending method. When the content of DHBAP in neat EP was 8 wt%, it reached to the V‐0 rating and the limited oxygen index (LOI) value up to 34.0%. Furthermore, according to the cone calorimeter (CC) test results, the heat release rate (HRR), total heat release (THR), smoke produce rate (SPR) and total smoke production (TSP) of EP/8% DHBAP decreased by 26.3%, 21.3%, 37.0% and 60.9% when compared with neat EP, respectively, indicating that DHBAP had good inhibition on heat and smoke releases. Eventually, the flame‐retardant mechanism of DHBAP was further explored by X‐ray photoelectron spectroscopy (XPS), Raman spectroscopy, and pyrolysis‐gas chromatography/mass spectrometry (Py‐GC/MS). The results showed that DHBAP had good flame‐retardant activity in the gasous‐condensed two phases.     

Metal‐organic framework MIL‐53 (Fe)@C/graphite carbon nitride hybrids with enhanced thermal stability,flame retardancy,and smoke suppression for unsaturated polyester resin

Metal‐organic framework MIL‐53 (Fe)@C/graphite carbon nitride hybrid (MFeCN), a novel flame retardant, was synthesized by hydrothermal reaction and subsequently added into unsaturated polyester resin (UPR). The structure, morphology, and thermal stability of MFeCN were characterized by Fourier transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy‐dispersive X‐ray spectroscopy (EDS), and thermogravimetric analysis (TG). The thermal stability and flammability of the UPR composites were characterized by TG and cone calorimeter tests (CCT). The results of CCT demonstrated that the peak heat release rate (pHRR), total heat release (THR), peak smoke production rate (pSPR), and total smoke production (TSP) of UPR/MFeCN‐4 were reduced by 39.8%, 10.2%, 33.3%, and 14.5%, respectively, comparing with UPR. The results of TG and CCT indicated that MFeCN could improve the thermal stability, flame retardancy, and smoke suppression properties of the UPR composites. The residues after CCT were then characterized by laser Raman spectroscopy (LRS), XPS, and SEM. Finally, based on the above experimental results and analysis, the flame retardancy mechanism of MFeCN was proposed.     

Preparation of a novel phosphorus‐containing organosilicon and its effect on the flame retardant and smoke suppression of polyethylene terephthalate

A novel phosphorus‐containing silicone flame retardant (PDPSI) was prepared by Mannish reaction, and a series of PDPSI/PET composites were prepared by melt blending method. The nuclear magnetic resonance (¹H NMR), Fourier transformation infrared (FTIR), and the thermogravimetric analyzer (TGA) results indicated that PDPSI showed network structure and owned good thermal stability, with the char residue of 62.2% at 800°C. The flame retardancy of PDPSI/PET composites was characterized by limiting oxygen index (LOI), vertical burning tests (UL‐94), and cone calorimeter (CCT). The results revealed that the addition amount of PDPSI was 5%, the LOI value of PDPSI/PET composites increased to 27.3%, and UL‐94 test passed V‐0 rating. When the PDPSI loading was 3%, PET composites showed excellent flame retardancy and smoke suppression, with a decrease in the peak heat release rate (PHRR) by 71.19% and the total smoke release (TSP) reduced from 14.4 to 11.1m². The scanning electron microscopy (SEM) and FTIR results of char residue demonstrated that the flame‐retardant mechanism of PDPSI was solid phase flame retardant. PDPSI catalyzed the aromatization reaction of PET to promote the formation of a dense and continuous carbon layer, finally improving the flame retardancy and smoke suppression properties of PET.     

协效剂对膨胀阻燃聚丙烯基木塑复合材料的阻燃增效研究

赋予木塑复合材料(WPC)的阻燃性能成为近年来该领域国内外的研究热点之一。本文通过两轮正交试验,研究8种常见的协效剂对膨胀型阻燃剂(IFRs,m(聚磷酸铵,APP)∶m(季戊四醇,PER)=2∶1)的阻燃增效作用,筛选出具有显著协效作用的协效剂组MgO/EG(可膨胀石墨)/SiO_2,其组成为m(MgO)∶m(EG)∶m(SiO_2)=1∶5∶5,其与IFRs的最佳配比为m(IFRs)∶m(MgO/EG/SiO_2)=1∶0.18,得到性能良好的阻燃型聚丙烯基木塑复合材料。通过热重分析(TGA)和锥形量热分析(CONE)评价IFRs及协效剂组对聚丙烯(PP)基木塑复合材料(WPC)热稳定性能和阻燃性能的影响。结果表明,IFRs及MgO/EG/SiO_2的加入可以有效提高WPC的热稳定性,WPC/IFRs/MgO/EG/SiO_2600℃的残炭率达到22.42%。WPC/IFRs的热释放速率峰(PHRR)、总热释放量(THR)和总烟释放量(TSP)相比于WPC分别降低了21.9%、8.7%和22%。MgO/EG/SiO_2的加入可以进一步提高IFRs的阻燃效率,WPC/IFRs/MgO/EG/SiO_2的PHRR和THR相比于WPC分别降低了33.0%和13.8%。     

Flame‐retardant performance and mechanism of epoxy thermosets modified with a novel reactive flame retardant containing phosphorus,nitrogen, and sulfur

A novel phosphorus‐containing, nitrogen‐containing, and sulfur‐containing reactive flame retardant (BPD) was successfully synthesized by 1‐pot reaction. The intrinsic flame‐retardant epoxy resins were prepared by blending different content of BPD with diglycidyl ether of bisphenol‐A (DGEBA). Thermal stability, flame‐retardant properties, and combustion behaviors of EP/BPD thermosets were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), limited oxygen index (LOI) measurement, UL94 vertical burning test, and cone calorimeter test. The flame‐retardant mechanism of BPD was studied by TGA/infrared spectrometry (TGA‐FTIR), pyrolysis‐gas chromatography/mass spectrometry (Py‐GC/MS), morphology, and chemical component analysis of the char residues. The results demonstrated that EP/BPD thermosets not only exhibited outstanding flame retardancy but also kept high glass transition temperature. EP/BPD‐1.0 thermoset achieved LOI value of 39.1% and UL94 V‐0 rating. In comparison to pure epoxy thermoset, the average of heat release rate (av‐HRR), total heat release (THR), and total smoke release (TSR) of EP/BPD‐1.0 thermoset were decreased by 35.8%, 36.5% and 16.5%, respectively. Although the phosphorus content of EP/BPD‐0.75 thermoset was lower than that of EP/DOPO thermoset, EP/BPD‐0.75 thermoset exhibited better flame retardancy than EP/DOPO thermoset. The significant improvement of flame retardancy of EP/BPD thermosets was ascribed to the blocking effect of phosphorus‐rich intumescent char in condensed phase, and the quenching and diluting effects of abundant phosphorus‐containing free radicals and nitrogen/sulfur‐containing inert gases in gaseous phase. There was flame‐retardant synergism between phosphorus, nitrogen, and sulfur of BPD.     

Flame retardation of glass-fibre-reinforced polyamide 6 by a novel metal salt of alkylphosphinic acid

Aluminum salts of phosphinic acid mixture of diisobutylphosphinic acid and monoisobutylphosphinic acid (HPA-2TBA-Al) and glass fibres were compounded with polyamide 6 to prepare a series of flame retardant GF/PA6 composites via melt blending. The flame retardance and burning behaviors of the composites were investigated by limiting oxygen index (LOI), vertical burning test (UL-94), and Cone calorimeter test. The thermal properties and decomposition kinetics were investigated by thermogravimetric analysis (TGA) under N₂ atmosphere. Addition of HPA-2TBA-Al results in an increased LOI value, a UL-94 V-0 rating together with a decrease in both the values of PHRR and THR in Cone calorimetric analysis. Visual observations and scanning electronic microscopy (SEM) after flame retardant tests confirmed the char-formation which acts as a fire barrier in condense phase. Analysis of cone calorimeter data indicates that gas phase flame retardant mechanism exists in the GFPA6/HPA-2TBA-Al system.