TiO_2纳米阵列光阳极光电催化水分解研究进展

光电催化水分解制氢是目前解决能源危机与环境污染最理想的技术之一.设计和构筑高效的光阳极是实现光电催化技术实际应用的关键.在众多半导体光阳极材料中,TiO_2纳米阵列由于其快的电荷传输速率,高的光热稳定性,无毒和成本低等优点,已经被广泛用于光电催化水分解反应的研究.但是TiO_2本征的光吸收范围窄、光生电荷复合率高、表面水氧化动力学缓慢严重地制约了其太阳能-氢能转换效率.我们结合近年来国内外及本课题组的研究工作详细论述了TiO_2纳米阵列的改性策略,主要包括利用元素掺杂来拓展TiO_2的光吸收范围并提高导电性,构筑异质结促进光电极电荷的分离与转移,半导体敏化增加光电极的可见光吸收并促进电荷转移,表面处理用于增加表面水氧化反应速率.最后指出了该材料发展现状,并对其发展前景做出展望.我们为进一步提高TiO_2纳米阵列的光电催化水分解活性提供了理论指导和实践借鉴.     

电化学阻抗谱法研究铈改性TiO2纳米管阵列光电极裂解水产氢动力学

通过阳极氧化法在纯钛板上制备TiO2纳米管阵列电极.在光电化学电解池阳极中加入供电子物质乙二醇,显著减小了TiO2纳米管的电荷传递阻抗,促进了光电催化裂解水产氢反应.采用阴极电沉积和阳极氧化法制备了单质铈和氧化铈共同改性的TiO2纳米管阵列半导体光阳极,其平带电位向电负方向移动.采用电化学阻抗谱法(EIS)对改性后TiO2纳米管阵列在光电催化裂解水产氢中的电子传输性能以及界面性质进行了表征,确定了各阻抗弧对应的电极过程.采用合理的等效电路模型计算了电极的电子传输动力学参数.结果表明,经铈改性后的TiO2纳米管阵列膜电阻明显减小,有利于氢气的产生.探讨了单质铈与氧化铈促进TiO2纳米管阵列电荷传输的作用机理.     

TiO2纳米管阵列及其应用

TiO2纳米管阵列作为一种新型的纳米TiO2材料,由于具有独特的阵列结构和优异的性能,引起了人们的极大关注.本文介绍了采用阳极氧化法制备TiO2纳米管阵列的工艺条件、产物特性、形成机理,及其在氢传感器、光解水制氢、染料敏化太阳能电池与光催化降解污染物等领域的应用,分析了目前存在的问题,并提出了今后研究的对策.     

甘油-DMSO-H2O中阳极氧化TiO2纳米管阵列的生长与性能

采用NH4F-甘油-DMSO(二甲基亚砜)-H2O溶液体系的电化学阳极氧化法, 在金属钛基板上形成厚度为0.4-1.5 μm的有序TiO2纳米管阵列薄膜. 利用场发射电子扫描显微镜(FESEM)技术, 研究了电解液的组成及阳极氧化电压对TiO2纳米管阵列生长形貌的影响. 结果表明, 阳极氧化电压可以影响TiO2纳米管的径向尺寸和长度；通过改变电解液中DMSO/H2O的体积比, 能够调控纳米管的生成速率与形貌. 利用X射线衍射(XRD)对经过不同温度热处理的TiO2纳米管阵列薄膜的物相进行了分析. TiO2纳米管阵列薄膜的光电催化分解水过程的电压-电流特性测量显示, 光电流密度大于0.2 mA·cm-2.     

水热处理锐钛矿TiO2纳米管阵列及其增强的光电催化活性

在含氟溶液中,通过电化学阳极氧化钛片成功制备了高度有序的TiO2纳米管阵列,先在450℃下煅烧使其晶化为锐钛矿相,再在不同温度下水热处理了这些锐钛矿阵列。用XRD、SEM和XPS表征了所制备的样品。通过在氙灯光照下光电催化降解对氯苯酚水溶液来检测样品的活性。以对苯二甲酸作为探测分子,用荧光光谱检测了在氙灯光光照下样品表面产生的羟基自由基(.OH)。通过线性伏安扫描的间隙光照实验,测定了样品的光电流响应。结果表明后水热处理对锐钛矿TiO2纳米管阵列的结晶度和形貌没有影响,但光电催化活性明显增强,而不同温度处理的样品的活性差别不大。水热处理后的TiO2纳米管阵列的光电催化活性增强的原因是,水热后TiO2纳米管阵列表面羟基含量明显增加,使得其在光电催化过程中生成的.OH增加。     

氮掺杂TiO_2纳米管阵列的制备及其可见光光电催化活性研究

联用电化学阳极氧化和湿化学法制备氮掺杂的TiO2纳米管阵列膜.应用SEM、XPS、DRS分析、表征,并研究该膜层的形貌、组成和光学性质以及在卤钨灯照射下降解甲基橙水溶液的光电催化活性.结果表明:氮以取代掺杂的形式进入TiO2晶格,掺氮的TiO2纳米管阵列在可见光区有较强的吸收,其光电催化性能优于纯的TiO2纳米管阵列膜.     

Fe-Ni/TiO2纳米管阵列电极的制备、表征及光电催化还原五氯酚活性

采用阳极氧化法和浸渍电沉积联用法制备了不同负载量的Fe-Ni/TiO2纳米管阵列电极. 通过扫描电子显微镜(SEM)、 X射线光电子能谱(XPS)和电化学测量等手段对样品的微观形貌、 晶体结构和光电响应等特性进行分析. 考察了在0.6 V偏压下, 所制备的电极对五氯酚的光电催化还原性能. 结果表明, 适量的Fe和Ni纳米颗粒的负载, 降低了TiO2纳米管阵列光生电子-空穴对的复合几率; 浸渍电沉积5次的Fe-Ni/TiO2纳米管阵列电极光电催化还原降解五氯酚的效率为91.35%, 明显高于TiO2纳米管阵列电极.     

钛基TiO2纳米管阵列电极的光电催化性能

应用电化学阳极氧化法在纯Ti基底上制备高度有序的TiO2纳米管阵列,考察了Ti/TiO2光阳极的光电化学响应.以苯酚溶液为目标污染物,研究Ti/TiO2电极的光电催化性能,并与光催化性能进行比较.结果表明,该电极光电催化性能优于光催化性能.施加0.6 V电压时,光电催化性能最好.电化学阻抗谱分析显示,光电催化和光催化降解过程的速控步骤均为表面反应步骤,外加偏压减小了界面电荷转移阻抗,提高了光生载流子的分离效率.     

ZnFe2O4/TiO2纳米管阵列电极的制备及光电催化降解苯酚的研究

采用阳极氧化法和电沉积法制备出具有可见光响应的ZnFe2O4/TiO2纳米管阵列电极.用环境扫描电子显微镜(ESEM)、X-射线衍射(XRD)和透射电子显微镜(TEM)对制备的ZnFe2O4/TiO2纳米管阵列电极的表面形貌和结构进行了表征.结果表明,该方法成功地将ZnFe2O4纳米颗粒均匀分散在TiO2纳米管中,分布在管口处的较少.同时,详细讨论了反应物浓度、沉积时间、循环次数、沉积电压对ZnFe2O4/TiO2纳米管阵列电极性能的影响.通过在可见光下降解苯酚评价了复合电极的光催化活性,实验结果表明:由于ZnFe2O4和TiO2之间的协同效应,复合电极的光响应范围扩展到了可见光区域,光电催化活性提高1.5～2倍.     

Fe_2O_3/TiO_2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO2纳米管阵列,采用化学浴方法在TiO2纳米管阵列上修饰了Fe2O3纳米颗粒。利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能。结果表明,Fe2O3纳米颗粒的修饰将TiO2纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe2O3/TiO2纳米管阵列的光电流是未修饰的TiO2纳米管阵列的9倍。而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO2纳米管阵列高出30%。     

Synthesis of Bi-doped TiO2 Nanotubes and Enhanced Photocatalytic Activity for Hydrogen Evolution from Glycerol Solution

Bi‐doped TiO₂ nanotubes with variable Bi/Ti ratios were synthesized by hydrothermal treatment in 10 mol·L^?1 NaOH (aq.) through using Bi‐doped TiO₂ particles derived from conventional sol‐gel method as starting materials. The effects of Bi content on the morphology, textural properties, photo absorption and photocatalytic activity of TiO₂ nanotubes were investigated. The scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS) observations of the obtained samples revealed the formation of titanate nanotube structure doped with Bi, which exists as a higher oxidation state than Bi³⁺. Bi‐doping TiO₂ nanotubes exhibited an extension of light absorption into the visible region and improved photocatalytic activities for hydrogen production from a glycerol/water mixed solution as compared with pure TiO₂ nanotubes. There was an optimal Bi‐doped content for the photocatalytic hydrogen production, and high content of Bi would retard the phase transition of titanate to anatase and result in morphology change from nanotube to nanobelt, which in turn decreases the photocatlytic activity for hydrogen evolution.     

TiO2 Nanotube Arrays Modified with Cr‐Doped SrTiO3 Nanocubes for Highly Efficient Hydrogen Evolution under Visible Light

In recent decades, solar‐driven hydrogen production over semiconductors has attracted tremendous interest owing to the global energy and environmental crisis. Among various semiconductor materials, TiO₂ exhibits outstanding photocatalytic properties and has been extensively applied in diverse photocatalytic and photoelectric systems. However, two major drawbacks limit practical applications, namely, high charge‐recombination rate and poor visible‐light utilization. In this work, heterostructured TiO₂ nanotube arrays grafted with Cr‐doped SrTiO₃ nanocubes were fabricated by simply controlling the kinetics of hydrothermal reactions. It was found that coupling TiO₂ nanotube arrays with regular SrTiO₃ nanocubes can significantly improve the charge separation. Meanwhile, doping Cr cations into SrTiO₃ nanocubes proved to be an effective and feasible approach to enhance remarkably the visible‐light response, which was also confirmed by theoretical calculations. As a result, the rate of photoelectrochemical hydrogen evolution of these novel heteronanostructures is an order of magnitude larger than those of TiO₂ nanotube arrays and other previously reported SrTiO₃/TiO₂ nanocomposites under visible‐light irradiation. Furthermore, the as‐prepared Cr‐doped SrTiO₃/TiO₂ heterostructures exhibit excellent durability and stability, which are favorable for practical hydrogen production and photoelectric nanodevices.     

Photoelectrochemical water splitting and simultaneous photoelectrocatalytic degradation of organic pollutant on highly smooth and ordered TiO2 nanotube arrays

The photoelectrochemical water splitting and simultaneous photoelectrocatalytic degradation of organic pollutant were achieved on TiO₂ nanotube electrodes with double purposes of environmental protection and renewable energy production under illumination of simulated solar light. The TiO₂ nanotube arrays (TiO₂ NTs) were fabricated by a two-step anodization method. The TiO₂ NTs prepared in two-step anodization process (2-step TiO₂ NTs) showed much better surface smoothness and tube orderliness than TiO₂ NTs prepared in one-step anodization process (1-step TiO₂ NTs). In the photoelectrochemical water splitting and simultaneous photoelectrocatalytic decomposition process, the 2-step TiO₂ NTs electrode showed both highest photo-conversion efficiency of 1.25% and effective photodecomposition efficiency with existing of methylene blue (MB) as sacrificial agent and as pollutant target. Those results implied that the highly ordered nanostructures provided direct pathway and uniform electric field distribution for effective charges transfer, as well as superior capabilities of light harvesting.     

Visible Light Photocatalytic Activity of Pt/N‐TiO2 towards Enhanced H2 Production from Water Splitting

Present work mainly focuses on experimental investigation to improvement of hydrogen production by water photoelectrolysis. An experimental facility was designed and constructed for visible light photocatalysis. A series of N‐TiO₂ photocatalysts impregnated with platinum on the surface of N‐TiO₂ were prepared. Hydrogen production upon irradiating aqueous Pt/N‐TiO₂ suspension with visible light was investigated. The shift in excitation wavelength of TiO₂ was 380 nm improved the yield of hydrogen production by N‐TiO₂ and Pt/N‐TiO₂. We used a 400 W mercury arc lamp combined with a 400 nm cutoff filter eliminating all the wavelengths under 400 nm. Pt/N‐TiO₂ material was characterized with TPR, reflective UV/Visible spectroscopy and TEM. The best hydrogen production rate obtained for this setup for N/Ti = 10, 0.05 wt% Pt/N‐TiO₂, through water splitting was about 772 μmolh^?1g^?1.     

Proton exchange reactions of C2–C4 alkanes sorbed in ZSM-5 zeolite

Photoelectrochemical cells with TiO₂ electrodes to convert sunlight and water into gaseous hydrogen and oxygen are a source of clean and renewable fuel. Despite their great potential, far-from-ideal performance and poor utilization of the solar spectrum have prevented them from becoming a widespread and practical technology. We review recent experimental work that uses dynamics measurements to study limitations of photoelectrochemical cells from a fundamental level and the use of TiO₂ nanotube arrays as a superior alternative to TiO₂ nanoparticles. Through a combination of nanoscale size control, doping, composite materials, and the incorporation of noble-metal nanoparticles, improved performance and light harvesting are demonstrated.     

Fabrication of multi-sectional TiO 2 nanotube arrays by anodization

We report a facile method to grow multi-sectional TiO₂ nanotube arrays consisting of alternating bamboo-shaped and smooth-walled nanotube sections by anodization. Two key factors are necessary for obtaining these morphologies. First, in order to avoid possible disruptions between the conjoint sections of the nanotube, the distribution of hydrogen ions is suggested not to be fiercely disturbed when switching from the first to the second stage. Second, to avoid the disruption of the nanotube at the joint which results from the disparity in diameters between sections, the direct current voltage is set to be the maximum of the square wave voltage. These newly developed TiO₂ nanotube arrays are expected to have potential applications in solar cells, drug release and delivery systems.     

阴离子改性甘油溶液中TiO2纳米管阵列的制备和表征

本文采用电化学阳极氧化法以含氟的甘油和水混合溶液为电解液在纯钛表面制备了一层排列规整的TiO2纳米管阵列,研究了电解液中额外添加3种2价阴离子、不同的电解时间及不同的添加物浓度等因素对所获得的TiO2纳米管阵列形貌的影响。结果表明,在改性电解液中制备的TiO2纳米管阵列的长度均超过了未改性的电解液中制备的,并随着氧化时间的增长,纳米管管口直径增大,管壁变薄;同时添加的(NH4)2TiF6浓度在0.025~0.1 mol.L-1范围内均可获得管长更长且形貌较好的TiO2纳米管阵列。     

Photocatalysis: Light energy conversion for the oxidation,disinfection, and decomposition of water

The results of many-year studies of the relationship between the physical properties and photocatalytic activity of TiO₂ and Pt/TiO₂ in photocatalytic purification and disinfection of air and water and water photodecomposition with oxygen evolution are presented. Recommendations are given as to finding the optimal method for platinum supporting on TiO₂ to achieve the highest possible catalytic activity. Multisite kinetic models of the gas-phase oxidation of simple organic substances are considered. Methods for regenerating the photocatalyst after its deactivation in the oxidation of sulfur-containing organic substances are suggested. New data are discussed on the acceleration of air purification by the combination of photocatalytic oxidation with atmospheric electric discharges, the addition of gaseous hydrogen peroxide, and oxidation on photocatalysts existing in the aerosol state. As compared to pure TiO₂, platinated titanium dioxide has a higher capability for disinfection and complete mineralization of microorganisms. Two promising methods for production of hydrogen from water using solar light are presented.     

TiO2 nanotube arrays fabricated by anodization in different electrolytes for biosensing

Titania nanotube arrays were fabricated by anodic oxidation of titanium foil in different electrolytes. The morphology, crystallinity and composition of the as-prepared nanotube arrays were studied by XRD, SEM and EDX. Electrochemical impedance spectroscopy (EIS) was employed to investigate their electrical conductivity and capacitance. Titania nanotube arrays co-adsorbed with horseradish peroxidase (HRP) and thionine chloride (Th) were studied for their sensitivity to hydrogen peroxide by means of cyclic voltammetric and galvanostatic measurements. The experiments showed that TiO₂ nanotube arrays possessed appreciably different sensitivities to H₂O₂ due to their different conductivity. Further experiments revealed that TiO₂ nanotubes have noticeably different ability of adsorbing HRP and Th, and the best sensitivity was achieved when the density of HRP is the highest. The TiO₂ nanotube arrays fabricated in potassium fluoride solution demonstrated the best sensitivity on hydrogen peroxide in the range of 10⁻⁵–3 × 10⁻³ M at pH 6.7 and at a potential of −600 mV (vs. Ag/AgCl).     

Quantum Chemical Study of Water Adsorption on the Surfaces of SrTiO3 Nanotubes

We have studied the adsorption of water molecules on the inner and outer surfaces of nanotubes generated by rolling (001) layers of SrTiO₃ cubic crystals. The stability and the atomic and electronic structures of the adsorbed layers are determined by using hybrid density functional theory. The absorption energy and the preferred adsorbate structure are essentially governed by the nature of the surface of the nanotube. Dissociative adsorption prevails on the outer nanotube surfaces. The stability of the adsorbed layers on the inner surfaces is related to the possibility of the formation of hydrogen bonds between water molecules and surface oxygen atoms, and depends on the surface curvature. The presence of water molecules on the inner surface of the nanotubes leads to an increase of the electronic band gap. Externally TiO₂‐terminated nanotubes could be used for the photocatalytic decomposition of water by ultraviolet radiation.