电纺丝-气相沉积法制备碳包覆TiO_2纳米纤维及其光催化行为的研究

以聚乙烯吡咯烷酮(PVP)溶胶/钛酸正丁酯为前躯体,以静电纺丝法制备了PVP/Ti(OC4H9)4纤维。550℃下,空气氛中焙烧双组分纤维,得到直径60～300nm的TiO2纳米纤维。继而以气相沉积法制得碳包覆TiO2纳米纤维。用红外吸收光谱(FTIR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等对纳米纤维进行了表征。与TiO2纳米纤维、TiO2纳米粉体相比,气相沉积法制备的碳包覆TiO2纳米纤维在光分解亚甲基蓝上表现出更好的催化性能。     

同轴静电纺丝法在纳米中空Ti02纤维中填充Ag的应用

以聚乙烯吡咯烷酮(PVP)溶胶,钛酸四正丁酯和PVP溶胶,银颗粒为前驱体,以共轴静电纺丝法制备了银填充的TiO2中空纳米纤维.将双组分纤维在200℃下热处理去除乙醇与表面吸附水后,继而在空气气氛中焙烧至600℃.可以得到在内表面上沉积银颗粒的TiO2纳米管,银颗粒的直径为5-40 nm,TiO2纳米管的外径150-300 nm.管臂厚10-20 nm.用红外吸收光谱(IR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等测试手段对超细纤维进行了表征.中空纤维的直径和管壁可以通过改变电纺参数来调节.与Ag-TiO2纳米纤维、TiO2纳米中空纤维、TiO2纳米纤维及TiO2纳米粉体相比较,Ag颗粒填充的TiO2纳米中空纤维在光分解亚甲基蓝上表现出了更好的光催化性能.     

同轴静电纺丝法在纳米中空TiO2纤维中填充Ag的应用

以聚乙烯吡咯烷酮(PVP)溶胶/钛酸四正丁酯和PVP溶胶/银颗粒为前驱体, 以共轴静电纺丝法制备了银填充的TiO2中空纳米纤维. 将双组分纤维在200 ℃下热处理去除乙醇与表面吸附水后, 继而在空气气氛中焙烧至600 ℃, 可以得到在内表面上沉积银颗粒的TiO2纳米管, 银颗粒的直径为5-40 nm, TiO2纳米管的外径150-300 nm, 管臂厚10-20 nm. 用红外吸收光谱(IR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等测试手段对超细纤维进行了表征. 中空纤维的直径和管壁可以通过改变电纺参数来调节. 与Ag-TiO2纳米纤维、TiO2纳米中空纤维、TiO2纳米纤维及TiO2纳米粉体相比较, Ag颗粒填充的TiO2纳米中空纤维在光分解亚甲基蓝上表现出了更好的光催化性能.     

同轴静电纺丝法在纳米中空TiO2纤维中填充Ag的应用

以聚乙烯吡咯烷酮（PVP）溶胶/钛酸四正丁酯和PVP溶胶/银颗粒为前驱体,以共轴静电纺丝法制备了银填充的TiO2中空纳米纤维.将双组分纤维在200℃下热处理去除乙醇与表面吸附水后,继而在空气气氛中焙烧至600℃,可以得到在内表面上沉积银颗粒的TiO2纳米管,银颗粒的直径为5-40nm,TiO2纳米管的外径150-300nm,管臂厚10-20nm.用红外吸收光谱（IR）、X射线衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）等测试手段对超细纤维进行了表征.中空纤维的直径和管壁可以通过改变电纺参数来调节.与Ag-TiO2纳米纤维、TiO2纳米中空纤维、TiO2纳米纤维及TiO2纳米粉体相比较,Ag颗粒填充的TiO2纳米中空纤维在光分解亚甲基蓝上表现出了更好的光催化性能.     

Ag-TiO2/蒙脱土复合纳米光催化剂的研究

本文以蒙脱土(简称MMT)为载体,利用四氯化钛水解法将纳米TiO2引入到蒙脱土层间,经500℃煅烧后得到稳定结构的TiO2柱撑蒙脱土,再通过化学还原法将金属银负载于其上,合成出载银/二氧化钛柱撑蒙脱土复合光催化剂(Ag-TiO2/MMT).通过XRD、IR、BET、AAS等分析方法对复合光催化剂的物相组成、键合状况、比表面积、元素含量等物化性质进行了表征.对降解亚甲基蓝的光催化活性测试表明具有如下的光催化活性序列:Ag-TiO2/MMT>TiO2/MMT>TiO2(P25),其中Ag-TiO2/MMT由于柱化后具有较大的比表面积和Ag的负载改性而具有最高的光催化活性.     

电纺丝合成树枝状Ag-TiO2复合材料及光催化降解有机物

通过高压电纺丝方法合成TiO2纳米纤维, 以此为模板构建树枝状Ag-TiO2复合材料. 采用 X 射线衍射与扫描电镜对该材料进行结构与形貌表征. 与商品化的TiO2(P25)及TiO2纳米纤维相比, 该复合材料在亚甲基蓝的光催化降解过程中表现出更优异的催化性能.     

溶胶-凝胶自蔓燃法制备铁掺杂纳米TiO2光催化剂

为了研究溶胶-凝胶自蔓燃法（SHS）制备的铁掺杂纳米TiO2的光催化活性,以TiCl4为原料制备了Fe3+掺杂TiO2光催化剂,分别在低压汞灯、中压汞灯和太阳光照射下进行了亚甲基蓝降解实验。 XRD和SEM显示,以TiCl4为前驱体,n(Ti)∶n(柠檬酸)∶n(NH4NO3)=1∶3∶5,经250 ℃自蔓燃和500 ℃热处理后,TiO2呈疏松、多孔的灰白色锐钛型粉体,粒径约为20 nm;在不同光源作用下,掺铁摩尔分数为0.02%的TiO2催化活性均最大;亚甲基蓝溶液在掺铁分数为0.02%的TiO2作用下,经太阳光照90 min后降解率达到了96.1%,为纯TiO2的1.78倍。     

卟啉化聚合物纤维膜负载TiO_2光催化剂的制备及其光催化性能研究

通过烯基铁卟啉分别和苯乙烯、丙烯腈及甲基丙烯酸甲酯共聚制备三种卟啉化聚合物,然后利用静电纺丝技术将这三种卟啉共聚物与TiO2颗粒共纺制备卟啉共聚物纤维膜负载TiO2光催化剂。扫描电子显微镜(SEM)表征结果显示卟啉共聚物纤维负载TiO2催化剂都具有良好的纤维结构,纤维直径约为1.0-2.0μm。X-射线衍射仪(XRD)则表明TiO2的晶型在纺丝前后都没有受到明显影响。对甲基橙溶液的催化降解实验结果显示:铁卟啉-丙烯腈共聚物负载TiO2催化剂的光催化活性最高,而且铁卟啉的含量对催化剂催化活性起着非常重要的作用。优化后的铁卟啉-丙烯腈共聚物纤维膜负载TiO2光催化剂对甲基橙溶液的脱色率达到76.3%,同时纤维膜结构有利于催化剂的回收和重复使用。     

活性炭负载TiO2-Fe3O4磁性光催化剂的制备及性能

采用溶胶-凝胶法制备了易于固液分离的活性炭（AC）负载磁性光催化剂（TiO2-Fe3O4／AC）．样品通过SEM-EDX和X射线衍射法进行表征．通过在紫外光照射下降解亚甲基蓝评价其光催化降解能力．结果表明：负载22％Fe3O4的光催化剂（含20％TiO2和58％AC）的光催化活性最强（120min时亚甲基蓝的降解率达到87％,是纯TiO2的2．7倍）;磁性光催化剂可实现磁分离回收．     

Fe_2O_3/TiO_2纳米管阵列的制备及其光催化性能

在钛基体上采用阳极氧化法制备了TiO2纳米管阵列,采用化学浴方法在TiO2纳米管阵列上修饰了Fe2O3纳米颗粒。利用扫描电镜、X射线衍射和紫外可见漫反射光谱等手段对材料进行了表征,同时测试了材料的光电化学性能及其光催化降解亚甲基蓝染料废水的性能。结果表明,Fe2O3纳米颗粒的修饰将TiO2纳米管阵列的光响应拓宽至可见光区域,提高了光电流,Fe2O3/TiO2纳米管阵列的光电流是未修饰的TiO2纳米管阵列的9倍。而在光催化反应中,亚甲基蓝最高降解率可达80%,比未修饰的TiO2纳米管阵列高出30%。     

液相沉积法制备光催化活性TiO2薄膜和纳米粉体

采用液相沉积法，在35℃通过向六氟钛酸铵水溶液中添加硼酸和结晶诱导剂锐 铁矿型TiO2纳米晶，沉积出具有光催化活性的Ti02薄膜和纳米粉体．用XRD，AFM， 阶梯仪,UV-vis，BET法对Ti02薄膜和粉体的沉积条件、结构、厚度和性能进行了测 定和表征，并用亚甲兰的降解，评价了TiO2薄膜和纳米粉体的光催化活性．结果表 明，当反应物六氟钛酸铵与硼酸的摩尔比为1：2—1：4时，沉积的粉体和薄膜含有 锐钛矿相Ti02；经300℃热处理的Ti02薄膜和纳米粉体具有最高的光催化活性，它 的光催化活性是未经热处理前的5倍．本文还解释了经300℃热处理的薄膜和纳米粉 体具有最高光催化活性的原因．     

Synthesis, property characterization and photocatalytic activity of the novel composite polymer polyaniline/Bi2SnTiO7

A novel polyaniline/Bi(2)SnTiO(7 )composite polymer was synthesized by chemical oxidation in-situ polymerization method and sol-gel method for the first time. The structural properties of novel polyaniline/Bi(2)SnTiO(7) have been characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and X-ray spectrometry. The lattice parameter of Bi(2)SnTiO(7) was found to be a = 10.52582(8) ?. The photocatalytic degradation of methylene blue was realized under visible light irradiation with the novel polyaniline/Bi(2)SnTiO(7) as catalyst. The results showed that novel polyaniline/Bi(2)SnTiO(7 )possessed higher catalytic activity compared with Bi(2)InTaO(7) or pure TiO(2) or N-doped TiO(2) for photocatalytic degradation of methylene blue under visible light irradiation. The photocatalytic degradation of methylene blue with the novel polyaniline/Bi(2)SnTiO(7) or N-doped TiO(2) as catalyst followed first-order reaction kinetics, and the first-order rate constant was 0.01504 or 0.00333 min(-1). After visible light irradiation for 220 minutes with novel polyaniline/Bi(2)SnTiO(7 )as catalyst, complete removal and mineralization of methylene blue was observed. The reduction of the total organic carbon, the formation of inorganic products, SO(4)2- and NO(3-), and the evolution of CO(2) revealed the continuous mineralization of methylene blue during the photocatalytic process. The possible photocatalytic degradation pathway of methylene blue was obtained under visible light irradiation.     

单晶MoO3纳米片：静电纺丝法制备及光催化活性

以聚乙烯基吡咯烷酮(PVP)和钼酸铵((NH4)6Mo7O24.4H2O)为原料,利用静电纺丝技术结合溶胶过程制备了PVP/(NH4)6Mo7O24.4H2O前躯体,对前躯体缓慢控温处理制备MoO3纳米材料。通过X-射线光电子能谱(XPS)﹑红外光谱(FTIR)﹑X射线粉末衍射(XRD)和场发射扫描电子显微镜(FE-SEM)等表征手段研究了热处理温度对MoO3晶体生长和结构的影响。以亚甲基蓝(MB)的光降解为模型反应,研究了MoO3微纳米材料的光催化性能。结果表明,热处理温度500℃时生成的MoO3纳米片光催化活性最好,并探讨了其光催化机理。     

Photochromism-based detection of volatile organic compounds by W-doped TiO2 nanofibers

W-doped TiO(2) nanofibers with various compositions (W/Ti: 2-8%) were fabricated by the electrospinning method from respective precursor solutions containing tungsten(V) pentaethoxide, titanium tetraisopropoxide (TTIP), and polyvinylpyrrolidone (PVP), followed with calcination at 550 °C. Morphological and structural characteristics of these nanofibers were studied with SEM, XRD and XPS. W-doping inhibited the crystal growth and anatase-to-rutile transformation of TiO(2) nanofibers. W-doped TiO(2) nanofiber mats showed good photocatalytic oxidation abilities for acetone. Obvious color change from white to blue of mats during the photocatalysis process can be detected by naked eyes, which provides a good way in detection of pollutants in indoor air, especially for the volatile organic compounds (VOCs).     

Silver Nanoparticles Filling in TiO2 Hollow Nanofibers by Coaxial Electrospinning

This study investigated the coaxial electrospinning process of silver filling in TiO₂ ultrafine hollow fibers using polyvinyl pyrrolidone (PVP) sol/titanium n-butyloxide (Ti(OC₄H₉)₄) and PVP sol/silver nanoparticles as pore-directing agents. The bicomponent fibers were heat treated at 200 °C and calcined at 600 °C. Silver particles having diameters of 5 to 40 nm were deposited on the inner surface of the long hollow TiO₂ nanofibers (outer diameter of 150.300 nm) with mesoporous walls (thickness of 10.20 nm). The morphological structure of the filled ultrafine hollow fibers has been studied by means of infrared (IR) spectrum, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The diameters and wall thicknesses of the hollow fibers could be tuned by adjusting the electrospinning parameters. Compared with other nanostructured TiO₂ materials, such as mesoporous Ag-TiO₂ blending fibers, TiO₂ hollow nanofibers, TiO₂ nanofibers, and TiO₂ powders, the silver filled TiO₂ hollow fibers exhibited a higher photocatalytic activity toward the degradation of methylene blue.