同轴静电纺丝法在纳米中空TiO2纤维中填充Ag的应用

以聚乙烯吡咯烷酮(PVP)溶胶/钛酸四正丁酯和PVP溶胶/银颗粒为前驱体, 以共轴静电纺丝法制备了银填充的TiO2中空纳米纤维. 将双组分纤维在200 ℃下热处理去除乙醇与表面吸附水后, 继而在空气气氛中焙烧至600 ℃, 可以得到在内表面上沉积银颗粒的TiO2纳米管, 银颗粒的直径为5-40 nm, TiO2纳米管的外径150-300 nm, 管臂厚10-20 nm. 用红外吸收光谱(IR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等测试手段对超细纤维进行了表征. 中空纤维的直径和管壁可以通过改变电纺参数来调节. 与Ag-TiO2纳米纤维、TiO2纳米中空纤维、TiO2纳米纤维及TiO2纳米粉体相比较, Ag颗粒填充的TiO2纳米中空纤维在光分解亚甲基蓝上表现出了更好的光催化性能.     

同轴静电纺丝法在纳米中空Ti02纤维中填充Ag的应用

以聚乙烯吡咯烷酮(PVP)溶胶,钛酸四正丁酯和PVP溶胶,银颗粒为前驱体,以共轴静电纺丝法制备了银填充的TiO2中空纳米纤维.将双组分纤维在200℃下热处理去除乙醇与表面吸附水后,继而在空气气氛中焙烧至600℃.可以得到在内表面上沉积银颗粒的TiO2纳米管,银颗粒的直径为5-40 nm,TiO2纳米管的外径150-300 nm.管臂厚10-20 nm.用红外吸收光谱(IR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等测试手段对超细纤维进行了表征.中空纤维的直径和管壁可以通过改变电纺参数来调节.与Ag-TiO2纳米纤维、TiO2纳米中空纤维、TiO2纳米纤维及TiO2纳米粉体相比较,Ag颗粒填充的TiO2纳米中空纤维在光分解亚甲基蓝上表现出了更好的光催化性能.     

电纺丝-气相沉积法制备碳包覆TiO_2纳米纤维及其光催化行为的研究

以聚乙烯吡咯烷酮(PVP)溶胶/钛酸正丁酯为前躯体,以静电纺丝法制备了PVP/Ti(OC4H9)4纤维。550℃下,空气氛中焙烧双组分纤维,得到直径60～300nm的TiO2纳米纤维。继而以气相沉积法制得碳包覆TiO2纳米纤维。用红外吸收光谱(FTIR)、X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等对纳米纤维进行了表征。与TiO2纳米纤维、TiO2纳米粉体相比,气相沉积法制备的碳包覆TiO2纳米纤维在光分解亚甲基蓝上表现出更好的催化性能。     

Micro- and nano-scale hollow TiO2 fibers by coaxial electrospinning: Preparation and gas sensing

We report the preparation of micro- and nano-scale hollow TiO₂ fibers using a coaxial electrospinning technique and their gas sensing properties in terms of CO. The diameter of hollow TiO₂ fibers can be controlled from 200 nm to several micrometers by changing the viscosity of electrospinning solutions. Lower viscosities produce slim hollow nanofibers. In contrast, fat hollow microfibers are obtained in the case of higher viscosities. A simple mathematical expression is presented to predict the change in diameter of hollow TiO₂ fibers as a function of viscosity. The successful control over the diameter of hollow TiO₂ fibers is expected to bring extensive applications. To test a potential use of hollow TiO₂ fibers in chemical gas sensors, their sensing properties to CO are investigated at room temperature.     

Synthesis,Characterization, and Photocatalytic Properties of Ag/TiO2 Composite Nanofibers Prepared by Electrospinning

Ag nanoparticles (Ag NPs) embedded titanium dioxide (TiO₂) nanofibers were fabricated by colloidal sol process, electrospinning, and calcination technique. Calcination of the electrospun nanofibers were heat treated at 600°C for 180 minutes in air atmosphere. X-ray diffraction patterns exhibited that the anatase phase and silver coexisted in the resulted Ag NPs/TiO₂ nanofibers; transmission electron microscopy demonstrated Ag NPs well spread in the porous microstructure of composite fibers. The prepared nanofibers were utilized as photocatalyst for degradation of methyl orange. The degradation rate of methyl orange dye solution containing Ag/TiO₂ composite nanofibers is 99% only after irradiation for 3 hours. It is proposed that these new Ag NPs/TiO₂ composite nanofibers will have potential application in water pollution treatment.      

A novel catalyst based on electrospun silver-doped silica fibers with ribbon morphology

Mesoporous silica nanofibers and Ag-doped composite nanoribbons were synthesized by a facile combination of an electrospinning technique and the sol–gel method. Tetraethyl orthosilicate, polyvinylpyrrolidone (PVP), triblock poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide), copolymer Pluronic P123, and silver nitrate (AgNO₃) were the components of sol for the production of Ag-doped hybrid silica ribbons. Heat removal of structure-directing agent P123 in the hybrid fibers at high temperatures resulted in a mesoporous morphology, and the degradation of PVP caused AgNO₃ to convert into silver in the form of nanoparticles. The size and content of the particles in the hybrid ribbons could be controlled by the concentration of AgNO₃ and thermal treatment conditions. Scanning electron microscopy, N₂ adsorption–desorption isotherm, transmission electron microscopy, X-ray diffraction, and UV–Vis spectroscopy were used to characterize the composite ribbons. The catalytic activity of the ribbons was evaluated by reduction of methylene blue dye and found to be better than in previous studies.     

LiCoO2 Hollow Nanofibers by Co‐Electrospinning Sol‐Gel Precursor

LiCoO₂ xerogel hollow nanofibers were first prepared by co‐electrospinning the sol precursor, and the polycrystalline LiCoO₂ hollow nanofibers were obtained after calcination of the xerogel fibers. The obtained hollow nanofibers made up of 20～30 nm nanocrystals were about 100 nm to several micrometers in outer diameter. The hollow nanofibers were detected by means of SEM, TEM, TG, DSC, FTIR, and XRD techniques.     

On heat transfer and flow characteristics of jets impinging onto a concave surface with varying jet arrangements

A new electrospinning process was developed for preparing TiO₂ nanofibers using a water-soluble Ti-precursor, [bis(kappa1O-hydroxo)(bis(kappa2O,O′-lactato)titanium(IV)] commonly known as titanium(IV) bis (ammonium lactato) dihydroxide (TiBALDH). The importance of the study is justified by the fact that Ti-precursors used for electrospinning, sol–gel, hydrothermal and other fiber synthesis processes are mostly non-water soluble. Accordingly, anatase TiO₂ nanofibers of diameter between 20 and 140 nm were synthesized by electrospinning and annealing. Polyvinylpyrrolidone (PVP) and different concentrations of TiBALDH were dissolved in a mixture of water, ethyl alcohol and acetic acid to optimize the electrospinning conditions. The thermal decomposition and fragmentation of PVP, TiBALDH and the fibers with 50% mass fraction of TiBALDH were studied by TGA-MS measurements. The fibers were then annealed at 1 °C min^?1 until 600 °C. The TiO₂ fibers were characterized using SEM–EDX, FTIR and XRD

     

Sol-Gel Co-Electrospun LiNiO2 Hollow Nanofibers

Using a coaxial capillary spinneret electrospinning technique combined with the sol-gel method, the nickelic xerogel hollow nanofibers first were prepared and the polycrystalline LiNiO₂ hollow nanofibers were obtained after sintering. The obtained hollow nanofibers were about 500 nm to 4 µm in outer diameter, and were made up of 20 ～ 30 nm nanocrystals. The xerogel hollow nanofibers and those calcined at different temperatures were characterized by thermogravimetric (TG) analysis, Fourier transform infrared (FTIR) spectrum, x-ray diffractometry (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM).     

Synthesis and characterization of hollow LiNiO<Subscript>2</Subscript> fibers via sol-electrospinning method

Hollow LiNiO₂ fibers have been prepared with a capillary spinneret electrospinning technique combined with the sol–gel method, and the possible mechanism for the fabrication of the hollow fibers was discussed. The xerogel fibers and those calcined at different temperatures were characterized by thermogravimetric (TG) analysis, X-ray diffractometry (XRD), Fourier transform infrared (FT-IR) spectrum, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and etc. The Polyvinyl Pyrrolidone (PVP) has an important role in the formation of hollow LiNiO₂ fibers.     

Synthesis of ordered mesoporous silica membrane on inorganic hollow fiber

This paper reports on a new method for the preparation of mesoporous silica membranes on alumina hollow fibers. A surfactant-silica sol is filled in the lumen of an alpha-alumina hollow fiber. The filtration technique combined with an evaporation-induced self-assembly (EISA) process results in the formation of a continuous ordered mesoporous silica layer on the outer side of alpha-alumina hollow fibers. X-ray diffraction (XRD), transmission electron microscopy (TEM), and nitrogen isothermal adsorption measurements reveal that these membranes possess hexagonal (P6mm) mesostructures with pore diameters of 4.48 nm and BET surfaces of 492.3 m(2) g(-1). Scanning electron microscopy (SEM) studies show that the layers are defect free and energy-dispersive spectroscopy (EDS) mapping images further confirm the formation of continuous mesoporous silica layer on the outer side of alpha-alumina hollow fibers. Nitrogen and hydrogen permeance tests show that the membranes are defect free.     

静电纺丝法制备铁酸锌中空纤维及其磁学性能

以锌盐、铁盐和聚乙烯吡咯烷酮(PVP)为原料,通过静电纺丝法先制备PVP/硝酸盐复合纤维,这些复合纤维以5℃·min-1的升温速率加热到500℃并保温3h,最终得到铁酸锌(ZnFe2O4)中空纤维.通过X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)以及振动样品磁强计(VSM)等分析手段对中空纤维的晶体结构、形貌和磁学性能进行了研究.结果显示,ZnFe2O4中空纤维属于尖晶石结构,高温处理后仍能保持一维结构,纤维直径在200-400nm之间,纤维壁由大小为25nm的颗粒堆积而成.室温磁化结果显示制备的ZnFe2O4中空纤维具有超顺磁性,在10kOe的磁化强度为2.03emu·g-1.     

Structural characterization of nano-crystalline Co3O4 ultra-fine fibers obtained by sol–gel electrospinning

In this paper, we report the obtention of ultrafine fibers of cobalt oxide (Co₃O₄) by combining electrospinning method with high-temperature calcinations from the precursor sol of poly(2-ethyl-2-oxazoline) (PEtOx)/cobalt acetate tetrahydrate [Co(CH₃COO)₂·4H₂O] in water. The optimum electrospinning conditions for obtaining precursor composite nanofibers from PEtOx/Co(CH₃COO)₂·4H₂O solution in water, to produce ceramic nanofibers, were studied. The average fiber diameter of the precursor composite fibers measured by scanning electron microscopy (SEM) was approximately 200 nm. Thermogravimetric analysis of PEtOx was performed to estimate the suitable calcination temperature of the precursor fibers. SEM images of the ceramic fibers obtained after calcination revealed the shrinkage in diameter due to complete degradation of the polymer and Co(CH₃COO)₂·4H₂O. Fourier transform infrared spectroscopy was used to ensure the complete pyrolysis of polymer during calcinations of the composite fibers. Crystalline properties of the ceramic fibers were studied by X-ray diffraction and high resolution transmission electron microscopy. The ceramic fibers are polycrystalline with an average grain size of ≈40 nm obtained at a calcination temperature of 773 K. It was observed that the grain sizes increased as the calcination temperature was increased, due to self assembly mechanism.     

Preparation of Mn2O3 and Mn3O4 nanofibers via an electrospinning technique

Thin PVA/manganese acetate composite fibers were prepared by using sol-gel processing and electrospinning technique. After calcinations of the above precursor fibers, Mn₂O₃ and Mn₃O₄ nanofibers with a diameter of 50-200 nm could be successfully obtained. The fibers were characterized by TG-DTA, Scanning electron microscopy, FT-IR, WAXD, respectively. The results showed that the crystalline phase and morphology of nanofibers were largely influenced by the calcination temperature.     

Structural characterization and photocatalytic activity of hollow binary ZrO2/TiO2 oxide fibers

The formation of hollow binary ZrO₂/TiO₂ oxide fibers using mixed precursor solutions was achieved by activated carbon fibers templating technique combined with solvothermal process. The samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), N₂ adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis, and infrared (IR) spectroscopy. The binary oxide system shows the anatase-type TiO₂ and tetragonal phase of ZrO₂, and the introduction of ZrO₂ notably inhibits the growth of TiO₂ nanocrystallites. Although calcined at 575 °C, all hollow ZrO₂/TiO₂ fibers exhibit higher surface areas (>113 m²/g) than pure TiO₂ hollow fibers. The Pyridine adsorption on ZrO₂/TiO₂ sample indicates the presence of stronger surface acid sites. Such properties bring about that the binary oxide system possesses higher efficiency and durable activity stability for photodegradation of gaseous ethylene and trichloromethane than P25 TiO₂. In addition, the macroscopic felt form for the resulting materials is more beneficial for practical applications than traditional catalysts forms.     

Preparation of ZnFe2O4 Nanofibers by Sol‐Gel Related Electrospinning Method

Zinc ferrite gel fibers were prepared from the sol precursor by the electrospinning method, and the ZnFe₂O₄ polycrystalline nanofibers were obtained upon calcination of the gel fibers. The obtained ZnFe₂O₄ nanofibers composed of 20–30 nm nanocrystals were about one hundred to several hundred nanometers in diameter. The materials have been characterized by means of SEM, TEM, XRD, TGA, and IR techniques.     

Aligned polymer fibers produced via an additive electric field

Electrospinning is known to be a highly versatile method to produce nanofibers, and several techniques have been developed to align nanofibers. In this paper, poly(vinyl alcohol) (PVA), poly(vinylpyrrolidone) (PVP), poly(propylene carbonate) (PC), poly(ethylene oxide) (PEO), PVA/Chitosan and PVA/Fe₃O₄ uniaxially aligned ultrafine fibers were obtained with electrospinning method by adding another electric field in the collection area. Alignment of the nanofibers was characterized by the use of digital cameras and field emission scanning electron microscopy, polarized Fourier transform infrared spectroscopy (FTIR), and wideangle X-ray diffraction (XRD). The mechanism of fiber alignment was investigated as well.     

Fabrication and characterization of NiTiO3 nanofibers by sol–gel assisted electrospinning

Continuous NiTiO₃ nanofibers have been successfully synthesized by a sol–gel assisted electrospinning method followed by calcination at 600 °C in air. These nanofibers were characterized for the morphological, structural and optical properties by scanning electron microscopy (SEM), energy-dispersive X-ray spectrum (EDS), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV–visible (UV–vis) diffuse reflectance spectroscopy (DRS). SEM results reveal that the obtained NiTiO₃ nanofibers are 175 nm in diameter and several micrometers in length after annealing at 600 °C. The XRD analysis shows that the nanofibers possess highly crystalline structure with no impurity phase. In contrast, the NiTiO₃ nanoparticles synthesized at the identical conditions by a sol–gel route have impurities including TiO₂ and NiO. Moreover, the electrospun NiTiO₃ nanofibers are endowed with an obvious optical absorbance in the visible range, demonstrating they have visible light photoresponse.     

Ag nanoparticle-embedded one-dimensional β-CD/PVP composite nanofibers prepared via electrospinning for use in antibacterial material

Ag nanoparticle-embedded one-dimensional β-CD (β-cyclodextrin)/PVP composite nanofibers were prepared using a one-step electrospinning technique. Ag nanoparticles were obtained in the AgNO₃/β-CD/DMF solution, in which silver nitrate been introduced as the precursor, DMF as solvent, β-CD as reducing and capping agent. After electrospinning of the composite solution at room temperature, the β-CD/PVP nanofibers containing Ag nanoparticles were obtained. The electrospun composite solution containning Ag nsnopsrticles were confirmed by UV-visible absorption spectra; the resulting composite nanofibers were characterized by scanning electron microscopy , transmission electron microscopy, and X-ray diffraction. Ag-β-CD/PVP nanofiber exhibits good antibacterial property for Escherichia coli and Staphylococcus aureus. Consequently, we propose that these Ag nanoparticle-embedded 1D-nanostructures prepared via electrospinning may be used as antibacterial material.     

Electrochemical Properties of Fiber‐in‐Tube‐ and Filled‐Structured TiO2 Nanofiber Anode Materials for Lithium‐Ion Batteries

Phase‐pure anatase TiO₂ nanofibers with a fiber‐in‐tube structure were prepared by the electrospinning process. The burning of titanium‐oxide‐carbon composite nanofibers with a filled structure formed as an intermediate product under an oxygen atmosphere produced carbon‐free TiO₂ nanofibers with a fiber‐in‐tube structure. The sizes of the nanofiber core and hollow nanotube were 140 and 500 nm, respectively. The heat treatment of the electrospun nanofibers at 450 and 500 °C under an air atmosphere produced grey and white filled‐structured TiO₂ nanofibers, respectively. The initial discharge capacities of the TiO₂ nanofibers with the fiber‐in‐tube and filled structures and the commercial TiO₂ nanopowders were 231, 134, and 223 mA h g^?1, respectively, and their corresponding charge capacities were 170, 100, and 169 mA h g^?1, respectively. The 1000th discharge capacities of the TiO₂ nanofibers with the fiber‐in‐tube and filled structures and the commercial TiO₂ nanopowders were 177, 64, and 101 mA h g^?1, respectively, and their capacity retentions measured from the second cycle were 89, 82, and 52 %, respectively. The TiO₂ nanofibers with the fiber‐in‐tube structure exhibited low charge transfer resistance and structural stability during cycling and better cycling and rate performances than the TiO₂ nanofibers with filled structures and the commercial TiO₂ nanopowders.