Flow-injection chemiluminescence determination of chloroquine using peroxynitrous acid as oxidant

A new flow-injection chemiluminescence (CL) method for determination of chloroquine is proposed based on a stronger chemiluminescence of chloroquine in hydrogen peroxide-nitrite-sulfuric acid medium. The proposed method allows the measurement of chloroquine over the range of 3.0×10⁻⁷ to 1.0×10⁻⁵ mol l⁻¹. The detection limit is 8.6×10⁻⁸ mol l⁻¹, and the relative standard deviation for 1.0×10⁻⁶ mol l⁻¹ chloroquine (n=11) is 1.6%. The CL mechanism is also discussed.     

Enzymatic chemiluminescent assay of glucose by sequential-injection analysis with soluble enzyme and on-line sample dilution

This work reports a sequential-injection analysis (SIA) method for the enzymatic assay of glucose with soluble glucose oxidase (GOD) and on-line sample dilution with chemiluminescence (CL) detection. A zone of sample was aspirated in the holding coil of the SIA manifold and, if necessary, was diluted on-line by means of an auxiliary dilution conduit. Then, a zone of GOD was aspirated adjacent to the sample zone and a stopped-flow period was applied to allow the enzymatic reaction to proceed with production of hydrogen peroxide. Then, zones of a catalyst (Co(II) solution) and alkaline luminol were aspirated into the holding coil. Finally, the flow was reversed and the stacked zones were sent to a flow-cell located in front of a photomultiplier tube (PMT) that monitored the CL intensity. The linear dynamic range was 1 × 10⁻⁵-1 × 10⁻³ mol L⁻¹ glucose, the coefficient of variation at 8 × 10⁻⁵ mol L⁻¹ of glucose was s_r = 3.1% (n = 8), the limit of detection at the 3σ level was c_L = 1 × 10⁻⁶ mol L⁻¹ and the sampling frequency was 28 h⁻¹. With on-line dilution by a factor of 1/200, the linear range could be extended up to 0.2 mol L⁻¹ glucose. The advantages of the proposed method are the simple manifold and instrumentation used, the scope for automated on-line dilution, the low consumption of sample and reagents and the elimination of enzyme immobilisation procedures. The method was applied to the analysis of commercial drinks and honey with percent relative errors in glucose determination in the range 100 ± 6.1%.     

Flow-injection chemiluminescence determination of ascorbic acid by use of the cerium(IV)-Rhodamine B system

A highly sensitive flow-injection (FI) method with chemiluminescence (CL) detection is used for the determination of l-ascorbic acid. The method is based on the CL reaction of Rhodamine B with cerium(IV) in sulfuric acid media. l-Ascorbic acid is suggested to be a catalyst utilized in the energy-transferred excitation process. The proposed procedure allows quantitation of l-ascorbic acid in the range 3.8×10⁻¹³ to 1.0×10⁻¹⁰ mol l⁻¹ with a correlation coefficient of 0.9998 (n=5) and relative standard deviation (R.S.D.) of 0.92% (n=11) at 1.0×10⁻¹¹ mol l⁻¹. The detection limit (3×blank) was 1.0×10⁻¹³ mol l⁻¹. The method is successfully used to determine l-ascorbic acid in fresh vegetables. The possible mechanism of the chemiluminescence in the system is discussed.     

Flow injection determination of thyroxine in pharmaceutical preparations using tris(2,2′-bipyridyl)ruthenium(III)-NADH chemiluminescence detection

A flow injection (FI) method is reported for the determination of thyroxine based on its enhancement of chemiluminescence (CL) from the Ru(bpy)₃³⁺-NADH system. The calibration graph was linear over the range 2.0-10 × 10⁻⁸ mol L⁻¹ (r² = 0.9989) with relative standard deviations (R.S.D.) in the range 2.0-4.5% (n = 4). The limit of detection (3σ blank) was 1.0 × 10⁻⁹ mol L⁻¹ with sample throughput of 120 h⁻¹. The effect of some organic compounds, anions and cations were studied for l-thyroxine determination. The method was applied to pharmaceutical preparations and the results obtained were in reasonable agreement with the amount labeled. The method was statistically compared with the results obtained by RIA; no significant disagreement at 95% confidence limit was observed. A calibration graph of NADH over the range 1.3 × 10⁻⁸-1.3 × 10⁻⁶ mol L⁻¹ was also established (r² = 0.9992) with R.S.D. in the range1.0-3.5% (n = 4). The limit of detection (3σ) was 1.0 × 10⁻¹⁰ mol L⁻¹ NADH.     

Flow-injection chemiluminescence determination of fluoroquinolones by enhancement of weak chemiluminescence from peroxynitrous acid

A flow-injection chemiluminescence (CL) method is described for the determination of fluoroquinolones including ciprofloxacin, norfloxacin and ofloxacin. The method is based on the enhancement by these compounds of the weak CL from peroxynitrous acid. The linear ranges are 1.0×10⁻⁷ to 1.0×10⁻⁵ mol l⁻¹ for ciprofloxacin and norfloxacin, and 3.0×10⁻⁷ to 3.0×10⁻⁵ mol l⁻¹ for ofloxacin, respectively. The detection limits (S/N=3) are 4.5×10⁻⁸ mol l⁻¹ ciprofloxacin, 5.9×10⁻⁸ mol l⁻¹ norfloxacin and 1.1×10⁻⁷ mol l⁻¹ ofloxacin, respectively. The proposed method was applied to the determination of fluoroquinolones in pharmaceutical preparations.     

Highly selective electrogenerated chemiluminescence (ECL) for sulfide ion determination at multi-wall carbon nanotubes-modified graphite electrode

In the present work, a novel method for immobilization of carbon nanotubes (CNTs) on the surface of graphite electrode was proposed. We further found that superoxide ion was electrogenerated on this CNTs-modified electrode, which can react with sulfide ion combing with a weak but fast electrogenerated chemiluminescence (ECL) emission, and this weak ECL signal could be enhanced by the oxidative products of rhodamine B. In addition, the rate constant of this electrochemical reaction k⁰ was investigated and confirmed that the speed of electrogenerating superoxide ion was in accordance with the subsequent fast CL reaction. Thus, the fast CL reaction of superoxide ion with target brought in the possibility of high selectivity based on time-resolved, relative to other interferences. Based on these findings, an excellently selective and highly sensitive ECL method for sulfide ion was developed. Under the optimum conditions, the enhancing ECL signals were linear with the sulfide ion concentration in the range from 6.0 × 10⁻¹⁰ to 1.0 × 10⁻⁸ mol L⁻¹, and a 2.0 × 10⁻¹⁰ mol L⁻¹ detection limits (3σ) was achieved. In addition, the proposed method was successfully used to detect sulfide ion in environmental water samples.     

Selective determination of acenaphthylene by flow injection analysis with tris(2,2'-bipyridine)ruthenium(II) chemiluminescence detection

A simple, rapid flow injection chemiluminescence (FI-CL) method has been developed for selective determination of acenaphthylene (ACY), based on the CL produced in the reaction of tris(2,2′-bipyridine)ruthenium(III) (Ru(bipy)₃³⁺) and ACY in an acidic buffer solution. Under the optimum experimental conditions, the calibration curve was linear over the range 5.0 × 10⁻³ to 4.0 × 10⁻⁷ mol L⁻¹ for ACY. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol L⁻¹ and the relative standard deviation of 10 replicate measurements was 2.3% for 5.0 × 10⁻⁵ mol L⁻¹ of ACY. Selectivity of CL reaction of ACY from other 15 polycyclic aromatic hydrocarbons (PAHs) was investigated by flow injection method. The method was applied to determine the ACY content in soil.     

Development of a gold nanoparticles based chemiluminescence imaging assay and its application

In this paper, a novel gold nanoparticles based protein immobilization method was designed. Biocomposites of gold nanoparticles and proteins were successfully coated on poly(methyl methacrylate) (PMMA) plates and polystyrene microtiter plates. The proteins could be immobilized on solid materials with high density and better bioactivity. Based on above design, chemiluminescence (CL) imaging assay for determination of H₂O₂ and recombinant human interleukin-6 (rHu IL-6) was developed. The linear range and the loading capability were greatly improved when compared with imaging assay performed with direct proteins immobilization. Under the selected experimental conditions, a linear relationship was obtained between the CL intensity and the concentration of H₂O₂ in the range of 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹, and rHu IL-6 in the range of 2.0-312.0 pg mL⁻¹. The detection limits were 2 × 10⁻⁷ mol L⁻¹ (3σ) for H₂O₂ and 0.5 pg mL⁻¹ for rHu IL-6 with relative standard deviation of 3.8% for 3.0 × 10⁻⁵ mol L⁻¹ H₂O₂, and 4.4% for 39.0 pg mL⁻¹ rHu IL-6. This method has been applied to the determination of rHu IL-6 in human serum with satisfactory results.     

Simultaneous, sensitive and selective on-line chemiluminescence determination of Cr(III) and Cr(VI) by capillary electrophoresis

A novel in-capillary reduction and capillary electrophoretic (CE)-chemiluminescence (CL) method was developed for the sensitive and selective determination of chromium(III) and chromium(VI). The proposed method was based on the in-capillary reduction of Cr(VI) with acidic H₂O₂ to form Cr(III) using the zone-passing technique and chemiluminescence detection of Cr(III). The sample [Cr³⁺ and CrO₄²⁻], hydrochloric acid, and H₂O₂ (reductant) solution segments were injected for specified periods of time in this order from the anodic end of a capillary, followed by application of an appropriate running voltage between both ends. As both chromium species have opposite charges, Cr³⁺ migrates to the cathode while CrO₄²⁻ ion, moving oppositely to the anode, reacts with acidic H₂O_2, resulted in formation of Cr³⁺. Based on the migration time difference of both Cr³⁺ ions, they were separated by zone electrophoresis. Running buffer was composed of 0.02 mol l⁻¹ HAc-NaAc (pH 4.7) with 1×10⁻³ mol l⁻¹ EDTA. Parameters affecting CE-CL separation and detection, such as reductant concentration, mixing mode of the analytes with CL reagent, CL reaction reagent pH and concentration, stability of luminol-hydrogen peroxide mixed solution were optimized. The limits of detection for chromium(III) and chromium(VI) (3σ) were 6×10⁻¹³ mol l⁻¹ (mass concentration 12 zmol) and 8×10⁻¹² mol l⁻¹ (160 zmol), respectively. This method offered potential advantages of simplicity, sensitivity, selectivity and applicability to the determination of Cr(III) and Cr(VI) in environmental water.     

Chemiluminescence determination of ultramicro DNA with a flow-injection method

A high sensitive flow-injection chemiluminescence method for determination of calf thymus DNA and herring sperm DNA has been developed. The method is based on the chemiluminescence reaction of Rhodamine B-cerium(IV)-thermally denatured DNAs in sulfuric acid media. The proposed procedure allows quantitation of DNAs in the range 2.6×10⁻⁵ to 0.26 μg ml⁻¹ for calf thymus DNA and 5.0×10⁻⁸ to 5.0×10⁻⁵ μg ml⁻¹ for herring sperm DNA with correlation coefficients 0.9998 and 0.9996 (both n=11), respectively. The detection limits (3σ) are 6.5×10⁻⁶ μg ml⁻¹ for calf thymus DNA and 4.3×10⁻⁸ μg ml⁻¹ for herring sperm DNA. The possible mechanism of chemiluminescence in the system is discussed.     

Determination of thyroxine hormone by luminol chemiluminescence

A chemiluminescence (CL) flow system for determination of thyroxine (Thy) is presented. It is based on the catalytic effect of cobalt(II) on the CL reaction between luminol and hydrogen peroxide. The iodinated chemical structure of Thy causes a heavy atom effect. The luminol CL signals show significant quenching by Thy. The calibration graph for Thy is linear for 15-70 μg ml⁻¹ and the 3σ detection limits are 27 μg ml⁻¹ for d-Thy and 23 μg ml⁻¹ for l-Thy.     

Enhancement of on chip chemiluminescence signal intensity of tris(1,10-phenanthroline)-ruthenium(II) peroxydisulphate system for analysis of chlorpheniramine maleate in pharmaceutical formulations

The effect of detection chip geometry on chemiluminescence (CL) signal intensity of tris(1,10-phenanthroline)-ruthenium(II) peroxydisulphate system for analysis of chlorpheniramine maleate (CPM) in pharmaceutical formulations was investigated. It was observed that the design of the detection chip is very crucial and can play an important role in enhancing the CL signal intensity in this system. The CL signal intensity was enhanced 250% when a teardrop micromixer chip was used, compared to the commonly used serpentine chip geometry. The study was conducted using a multi-chip device. In this device, chip 1 was used to prepare and pump the reagent mixture, whereas chip 3 was used for pumping the sample. The two chips were connected to the teardrop chip (2) via silica capillary where detection took place. Non-linear regression curve fitting of the calibration data revealed that the calibration curves are best described by third order polynomial equation with excellent correlation coefficients (R² = 0.9998) for the concentration range 7.69 × 10⁻⁸ to 5.12 × 10⁻⁵ mol L⁻¹. A linear response is also observed over the range 7.69 × 10⁻⁸ to 1.28 × 10⁻⁵ mol L⁻¹ (R² = 0.9996) and the detection limit was found to be 5.49 × 10⁻⁸ mol L⁻¹. The device was successfully used for the analysis of CPM in tablets and a multi-component cough syrup. Results were reproducible with relative standard deviation (RSD) of 0.6-1.1%.     

β−cyclodextrins-based inclusion complexes of CoFe2O4 magnetic nanoparticles as catalyst for the luminol chemiluminescence system and their applications in hydrogen peroxide detection

β−cyclodextrins (β−CD)-based inclusion complexes of CoFe₂O₄ magnetic nanoparticles (MNPs) were prepared and used as catalysts for chemiluminescence (CL) system using the luminol-hydrogen peroxide CL reaction as a model. The as-prepared inclusion complexes were characterized by XRD (X-ray diffraction), TGA (thermal gravimetric analysis) and FT-IR. The oxidation reaction between luminol and hydrogen peroxide in basic media initiated CL. The effect of β−CD-based inclusion complexes of CoFe₂O₄ magnetic nanoparticles and naked CoFe₂O₄ magnetic nanoparticles on the luminol-hydrogen peroxide CL system was investigated. It was found that inclusion complexes between β−CD and CoFe₂O₄ magnetic nanoparticles could greatly enhance the CL of the luminol-hydrogen peroxide system. Investigation on the kinetic curves and the chemiluminescence spectra of the luminol-hydrogen peroxide system demonstrates that addition of CoFe₂O₄ MNPs or inclusion complexes between β−CD and CoFe₂O₄ MNPs does not produce a new luminophor of the chemiluminescent reaction. The luminophor for the CL system was still the excited-state 3-aminophthalate anions (3-APA*). The enhanced CL signals were thus ascribed to the possible catalysis from CoFe₂O₄ MNPs or inclusion complexes between β−CD and CoFe₂O₄ nanoparticles. The feasibility of employing the proposed system for hydrogen peroxide sensing was also investigated. Experimental results showed that the CL emission intensity was linear with hydrogen peroxide concentration in the range of 1.0 × 10⁻⁷ to 4.0 × 10⁻⁶ mol L⁻¹ with a detection limit of 2.0 × 10⁻⁸ mol L⁻¹ under optimized conditions. The proposed method has been used to determine hydrogen peroxide in water samples successfully.     

An emphatic orthogonal signal correction-support vector machine method for the classification of tissue sections of endometrial carcinoma by near infrared spectroscopy

A sequential injection analysis (SIA) spectrophotometric method for determining tetracycline (TC), chlortetracycline (CTC) and oxytetracycline (OTC) in different sample matrices were described. The method was based on the reaction between tetracyclines and yttrium (III) in weak basic micellar medium, yielding the light yellow complexes, which were monitored at 390, 392 and 395 nm, respectively. A cationic surfactant, cetyltrimethylammonium bromide (CTAB) was used to obtain the micellar system. The linear ranges of calibration graphs were between 1.0 × 10⁻⁵ and 4 × 10⁻⁴ mol L⁻¹, respectively. The molar absorptivities were 5.24 × 10⁵, 4.98 × 10⁴ and 4.78 × 10⁴ L mol⁻¹ cm⁻¹. The detection limits (3σ) were between 4.9 × 10⁻⁶ and 7.8 × 10⁻⁶ mol L⁻¹ whereas the limit of quantitations (10σ) were between 1.63 × 10⁻⁵ and 2.60 × 10⁻⁵ mol L⁻¹ the interday and intraday precisions within a weak revealed as the relative standard deviations (R.S.D., n = 11) were less than 4%. The method was rapid with a sampling rate of over 60 samples h⁻¹ for the three drugs. The proposed method has been satisfactorily applied for the determination of tetracycline and its derivatives in pharmaceutical preparations together with their residues in milk and honey samples collected in Chiang Mai Province. The accuracy was found to be high as the Student's t-values were found to be less than the theoretical ones. The results were compared favorably with those obtained by the conventional spectrophotometric method.     

Flow-injection chemiluminescence determination of aminomethylbenzoic acid and aminophylline based on N-bromosuccinimide-luminol reaction

A novel and sensitive chemiluminescence (CL) method for the determination of aminomethylbenzoic acid and aminophylline coupled with flow-injection analysis (FIA) technique is developed in this paper. It is based on the inhibition effect of the studied drugs on the chemiluminescence emission of N-bromosuccinimide-luminol (NBS-luminol) system. Under the optimum conditions, the decreased CL intensity is linear with the concentration of aminomethylbenzoic acid in the range of 2×10⁻⁸ to 1.0×10⁻⁶ g ml⁻¹ and with the concentration of aminophylline in the range of 1×10⁻⁷ to 7.0×10⁻⁶ g ml⁻¹, respectively. The detection limit is 7.0×10⁻⁹ g ml⁻¹ for aminomethylbenzoic acid (3σ) and 3.4×10⁻⁸ g ml⁻¹ for aminophylline (3σ). The relative standard deviations (R.S.D.) for 11 parallel measurements of 2.0×10⁻⁷ g ml⁻¹ aminomethylbenzoic acid and 1.0×10⁻⁶ g ml⁻¹ aminophylline are 2.6 and 3.0%, respectively. The proposed methods have been applied for the determination of the studied drugs in their pharmaceutical formulations with satisfactory results. The possible use of the proposed system for the determination of aminomethylbenzoic acid in plasma sample was also tested. The possible inhibition mechanism of aminomethylbenzoic acid and aminophylline on luminol-NBS system was discussed briefly.     

Application of a novel co-enzyme reactor in chemiluminescence flow-through biosensor for determination of lactose

A novel enzyme reactor with co-immobilization of β-galactosidase and glucose oxidase in calcium alginate fiber (CAF) and amine modified nanosized mesoporous silica (AMNMS) was prepared which incorporate the adsorption and catalysis of AMNMS with the cage effect of the polymer to increase catalytic activity and stability of immobilized enzyme. The enzyme reactor was applied to prepare a chemiluminescence (CL) flow-through biosensor for determination of lactose combined with a novel luminol-diperiodatonickelate (DPN) CL system we reported. It shows that the CL flow-through biosensor possesses long lifetime, high stability, high catalytic activity and sensitivity. The relative CL intensity was linear with the lactose concentration in the range of 8 × 10⁻⁸-4 × 10⁻⁶ g mL⁻¹ with the detection limit of 2.7 × 10⁻⁸ g mL⁻¹ (3σ). It has been successfully applied to the determination of lactose in milk.     

Rapid enzymatic chemiluminescent assay of glucose by means of a hybrid flow-injection/sequential-injection method

This work reports a hybrid flow-injection analysis (FIA)/sequential-injection analysis (SIA) method for the rapid enzymatic assay of glucose with soluble glucose oxidase (GOD). The method relies on the sequential injection of segments of the sample and of a solution of enzyme by means of a multi-port selection valve in a flowing water stream. As the two zones are swept downstream, they overlap and merge so that the glucose in the sample is enzymatically oxidised. The generated hydrogen peroxide is merged with an alkaline luminol solution and the chemiluminescence (CL) intensity is monitored and related to the glucose concentration in the sample. The linear range of the method for glucose determination is 0.01-1 mmol L⁻¹, the relative standard deviation is 3.9% at the 0.08 mmol L⁻¹ level (n = 8), the limit of detection at the 2σ level is 4 μmol L⁻¹ glucose and the injection rate is 80 h⁻¹. The method was applied to the analysis of energy drinks and honey with relative errors in glucose determination in the range 100 ± 4.3%. The advantages of the proposed method are the wide linear range, the simple instrumentation used, the low consumption of sample and reagents, the elimination of catalysts and immobilised enzymes and the high sample throughput.     

Sub-picogram determination of Vitamin B12 in pharmaceuticals and human serum using flow injection with chemiluminescence detection

A sensitive chemiluminescence (CL) method, based on the enhancive effect of cobalt(II) on the CL reaction between luminol and dissolved oxygen in a flow injection (FI) system, was proposed for determination of Vitamin B₁₂. The increment of the CL intensity was proportional to the concentration of Vitamin B₁₂, giving a calibration graph linear over the concentration from 2.0×10⁻¹⁰ to 1.2×10⁻⁶ g l⁻¹ (r²=0.9992) with the detection limit of 5.0×10⁻¹¹ g l⁻¹ (3σ). At a flow rate of 2.0 ml min⁻¹, a complete determination of Vitamin B₁₂, including sampling and washing, could be accomplished in 0.5 min with the relative standard deviations (R.S.D.) of less than 5.0%. The proposed method was applied successfully to the determination of Vitamin B₁₂ in pharmaceuticals, human serum, egg yolk and fish tissue.     

Sensitive and selective determination of molybdenum by flow injection chemiluminescence method combined with controlled potential electrolysis technique

A sensitive and selective flow injection chemiluminescence (CL) method combined with controlled potential electrolysis technique was described for the determination of molybdenum. The method is based on the chemiluminescence reaction of luminol with unstable molybdenum(III) in alkaline solution. The molybdenum(III) was on-line reduced from molybdenum(VI) via controlled potential electrolysis technique using a homemade flow-through carbon electrolytic cell at the potential of −0.6 V (versus Ag/AgCl). The method allows the determination of molybdenum in the 5.0×10⁻¹⁰ to 5.0×10⁻⁷ g ml⁻¹ range with a limit of detection (3σ) of 5×10⁻¹¹ g ml⁻¹ molybdenum. The relative standard deviation is 2.6% for the 1.0×10⁻⁹ g ml⁻¹ molybdenum solution in 11 repeated measurements. This method was successfully applied to the determination of molybdenum in water samples.     

Flow chemiluminescence sensor for determination of clenbuterol based on molecularly imprinted polymer

In this paper, a novel flow chemiluminescence (CL) clenbuterol sensor based on molecularly imprinted polymer (MIP) on line enrichment nanogram clenbuterol and chemiluminescence reaction of potassium permanganate and formaldehyde in the polyphosphate enhanced by clenbuterol. Clenbuterol in the urine was selectively adsorbed on the clenbuterol-imprinted polymer, which was packed into the flow cell. The formaldehyde and the polyphosphate with potassium permanganate flowed through the flow cell and reacted with the on line adsorbed clenbuterol and produced strong CL. The results show that the sensor was reversible. The CL intensity was linear with clenbuterol concentration from 1.0 × 10⁻⁹ g/mL to 5.0 × 10⁻⁸ g/mL. The detection limit was 3.0 × 10⁻¹⁰ g/mL. The R.S.D. for ng/mL clenbuterol was less than 5% (n = 3). The present method offered a high selectivity and sensitivity that made the quantitative analysis of trace clenbuterol (ng/mL) in the animal urine sample.