Enhanced electrochemical properties of Li<Subscript>2</Subscript>ZnTi<Subscript>3</Subscript>O<Subscript>8</Subscript>/C nanocomposite synthesized with phenolic resin as carbon source

Li₂ZnTi₃O₈/C nanocomposite has been synthesized using phenolic resin as carbon source in this work. The structure, morphology, and electrochemical properties of the as-prepared Li₂ZnTi₃O₈ samples were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscope (TEM), Raman spectroscopy (RS), galvanostatic charge–discharge, and AC impedance spectroscopy. SEM images show that Li₂ZnTi₃O₈/C was agglomerated with a primary particle size of ca. 40 nm. TEM images reveal that a homogeneous carbon layer (ca. 5 nm) formed on the surface of Li₂ZnTi₃O₈ particles which is favorable to improve the electronic conductivity and inhibit the growth of Li₂ZnTi₃O₈ during annealing process. The as-prepared Li₂ZnTi₃O₈/C composite with 6.0 wt.% carbon exhibited a high initial discharge capacity of 425 and 159 mAh g^?1 at 0.05 and 5 A g^?1, respectively. At a high current density of 1 A g^?1, 95.5 % of its initial value is obtained after 100 cycles.     

The effects of sintering temperature and time on the structure and electrochemical performance of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode materials derived from sol-gel method

LiNi _0.8Co _0.2O ₂ cathode materials were synthesized by the sol-gel method using citric acid as a chelating agent. The effects of sintering temperature and time on the structure and electrochemical performance of the materials were investigated. The materials were characterized by X-ray diffraction, together with refinement analysis by the Rietveld method. The results showed that sintering temperature and time had significant influence on the structure of the materials. The lattice parameters ( a, c, c/ a and volume) and the amount of Ni in the Li 3a site showed a peak shape change with sintering temperature and time. The sample sintering at 998 K for 24 h showed the best ordering layered structure with the maximum c/ a ratio and the least amount of Ni on the Li 3a site. The charge-discharge experiments also indicated that the sample had the best electrochemical properties, with an initial capacity of 181 mA h/g and a capacity retention of 82.9% after 50 cycles at a 0.1 C rate between 3.0 V and 4.2 V. In addition, the compositional homogeneity of these cathode materials derived using the sol-gel method was demonstrated by scanning electron microscopy/energy dispersive analysis.     

Improvement of the electrochemical properties of a LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material formed by a new solid-state synthesis method

In order to avoid the shortcomings of large particle size and poor uniformity of material synthesized by the traditional solid-state method, this paper utilizes a simple improvement of calcination process (i.e., calcination–milling–recalcination) based on the traditional solid-state synthesis to successfully prepare a large number of well-distributed, micrometer-sized, spherical secondary LiNi_0.5Mn_1.5O₄ particles. Each particle is composed of nano- and/or sub-micrometer-sized grains. Results of the electrochemical performance tests show that the material exhibits a remarkable cycle performance and rate capability compared with that obtained from traditional synthesis method; the spherical LiNi_0.5Mn_1.5O₄ particles can deliver a large capacity of 135.8 mAh g^?1 at a 1 C discharge rate with a high retention of 77 % after 741 cycles and a good capacity of 105.9 mAh g^?1 at 10 C. Cyclic voltammetry measurements confirm that the significantly improved electrochemical properties are due to enhanced electronic conductivity and lithium-ion diffusion coefficient resulting from the optimized morphology and particle size. This improved method is more suitable for mass production.     

Effects of polyvinyl alcohol on the electrochemical performance of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Al<Subscript>0.05</Subscript>O<Subscript>2</Subscript> cathode material

In view of the close relationship between the morphology of LiNi_0.8Co_0.15Al_0.05O₂ (NCA) and its electrochemical performance, polyvinyl alcohol (PVA) was added to control the NCA morphology. And thus a new NCA cathode material modified by PVA (NCA-PVA) was prepared. The morphology and structure of the obtained samples were characterized by X-ray diffraction, scanning electron microscopy, and laser diffraction. The electrochemical performance was characterized with electrochemical workstation and cell tester by assembling into CR2032 coin-type half-cell. The results show that the obtained NCA-PVA has a better layer structure and smaller cation mixing degree, smaller particle size, and more uniform particle size distribution than the pristine NCA without adding PVA. The electrochemical performance is also improved: the initial discharge capacity increases from 143.36 to 184.84 mAh g^?1. And the charge-discharge efficiency increases from 78.25 to 86.42%. The specific discharge capacities of NCA-PVA are all higher than that of the NCA (about 50 mAh g^?1) at all testing rates (0.1, 0.2, 0.5, 1.0, 2.0, and 5.0 C).     

Sn-doped Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode materials for lithium-ion batteries with enhanced electrochemical performance

Sn-doped Li-rich layered oxides of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ have been synthesized via a sol-gel method, and their microstructure and electrochemical performance have been studied. The addition of Sn⁴⁺ ions has no distinct influence on the crystal structure of the materials. After doped with an appropriate amount of Sn⁴⁺, the electrochemical performance of Li_1.2Mn_0.54-x Ni_0.13Co_0.13Sn _x O₂ cathode materials is significantly enhanced. The optimal electrochemical performance is obtained at x = 0.01. The Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode delivers a high initial discharge capacity of 268.9 mAh g^?1 with an initial coulombic efficiency of 76.5% and a reversible capacity of 199.8 mAh g^?1 at 0.1 C with capacity retention of 75.2% after 100 cycles. In addition, the Li_1.2Mn_0.53Ni_0.13Co_0.13Sn_0.01O₂ electrode exhibits the superior rate capability with discharge capacities of 239.8, 198.6, 164.4, 133.4, and 88.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively, which are much higher than those of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ (196.2, 153.5, 117.5, 92.7, and 43.8 mAh g^?1 at 0.2, 0.5, 1, 2, and 5 C, respectively). The substitution of Sn⁴⁺ for Mn⁴⁺ enlarges the Li⁺ diffusion channels due to its larger ionic radius compared to Mn⁴⁺ and enhances the structural stability of Li-rich oxides, leading to the improved electrochemical performance in the Sn-doped Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ cathode materials.     

Electrochemical properties of spinel Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> nanoparticles prepared via a low-temperature solid route

Spinel phase Li₄Ti₅O₁₂ (s-LTO) with an average primary particle size of 150 nm was synthesised via a solid state route by calcining a precursor mixture at 600 °C. The precursor was prepared from a stoichiometric mixture of TiO₂ nanoparticles and an ethanolic solution of Li acetate and activated by ball-milling. Effects of the calcination temperature and atmosphere are examined in relation to the coexistence of impurity phases by X-ray diffraction and ⁶Li MAS NMR. The charge capacity of s-LTO, determined from cyclic voltammogram at a scan rate of 0.1 mV/s, was 142 mAh/g. The capacity of our optimised material is superior to that of commercially available spinel (a-LTO), despite the considerably smaller BET-specific surface area of the former. The superior properties of our material were also demonstrated by galvanostatic charging/discharging. From these observations, we conclude that the presented low-temperature solid state synthesis route provides LTO with improved electrochemical performance.     

Towards high-performance cathode materials for lithium-ion batteries: Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Zn<Subscript>0.05</Subscript>O<Subscript>2</Subscript>

Zn-doped LiNi_0.8Co_0.2O₂ exhibits impressive electrochemical performance but suffers limited cycling stability due to the relative large size of irregular and bare particle which is prepared by conventional solid-state method usually requiring high calcination temperature and prolonged calcination time. Here, submicron LiNi_0.8Co_0.15Zn_0.05O₂ as cathode material for lithium-ion batteries is synthesized by a facile sol-gel method, which followed by coating Al₂O₃ layer of about 15 nm to enhance its electrochemistry performance. The as-prepared Al₂O₃-coated LiNi_0.8Co_0.15Zn_0.05O₂ cathode delivers a highly reversible capacity of 182 mA h g^?1 and 94% capacity retention after 100 cycles at a current rate of 0.5 C, which is much superior to that of bare LiNi_0.8Co_0.15Zn_0.05O₂ cathode. The enhanced electrochemistry performance can be attributed to the Al₂O₃-coated protective layer, which prevents the direct contact between the LiNi_0.8Co_0.15Zn_0.05O₂ and electrolyte. The escalating trend of Li-ion diffusion coefficient estimated form electrochemical impedance spectroscopic (EIS) also indicate the enhanced structural stability of Al₂O₃-coated LiNi_0.8Co_0.15Zn_0.05O₂, which rationally illuminates the protection mechanism of the Al₂O₃-coated layer.     

Facile synthesis of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript> microsheets with porous micro-nanostructure as high-rate cathode materials for Li-ion batteries

Porous LiMn₂O₄ microsheets with micro-nanostructure have been successfully prepared through a simple carbon gel-combustion process with a microporous membrane as hard template. The crystal structure, morphology, chemical composition, and surface analysis of the as-obtained LiMn₂O₄ microsheets are characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscope (XPS). It can be found that the as-prepared LiMn₂O₄ sample presents the two-dimensional (2-D) sheet structure with porous structure comprised with nano-scaled particles. As cathode materials for lithium-ion batteries, the obtained LiMn₂O₄ microsheets show superior rate capacities and cycling performance at various charge/discharge rates. The LiMn₂O₄ microsheets exhibit a higher charge and discharge capacity of 137.0 and 134.7 mAh g^?1 in the first cycle at 0.5 C, and it remains 127.6 mAh g^?1 after 50 cycles, which accounts for 94.7% discharge capacity retention. Even at 10 C rate, the electrode also delivers the discharge capacity of 91.0 mAh g^?1 after 300 cycles (93.5% capacity retention). The superior electrochemical properties of the LiMn₂O₄ microsheets could be attributed to the unique microsheets with porous micro-nanostructure, more active sites of the Li-ions insertion/deinsertion for the higher contact area between the LiMn₂O₄ nano-scaled particles and the electrolyte, and better kinetic properties, suggesting the applications of the sample in high-power lithium-ion batteries.     

Mn<Subscript>3</Subscript>O<Subscript>4</Subscript>/carbon nanotubes nanocomposites as improved anode materials for lithium-ion batteries

Mn₃O₄ and Mn₃O₄ (140)/CNTs have been investigated as high-capacity anode materials for lithium-ion batteries (LIBs) applications. Nanoparticle Mn₃O₄ samples were synthesized by hydrothermal method using Mn(Ac)₂ and NH₃·H₂O as the raw materials and characterized by XRD, TG, EA, TEM, and SEM. Its electrochemical performances, as anode materials, were evaluated by galvanostatic discharge-charge tests. The Mn₃O₄ (140)/CNTs displays outstanding electrochemical performances, such as high initial capacity (1942 mAh g^?1), stable cycling performance (1088 mAh g^?1 and coulombic efficiency remain at 97% after 60 cycles) and great rate performance (recover 823 mAh g^?1 when return to initial current density after 44 cycles). Compared to pure Mn₃O₄ (140), the improving electrochemical performances can be attributed to the existence of very conductive CNTs. The Mn₃O₄ (140)/CNTs with excellent electrochemical properties might find applications as highly effective materials in electromagnetism, catalysis, microelectronic devices, etc. The process should also offer an effective and facile method to fabricate many other nanosized metallic oxide/CNTs nanocomposites for low-cost, high-capacity, and environmentally benign materials for LIBs.     

The influence of Li sources on physical and electrochemical properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials for lithium-ion batteries

LiNi_0.5Mn_1.5O₄ cathode materials were successfully prepared by sol–gel method with two different Li sources. The effect of both lithium acetate and lithium hydroxide on physical and electrochemical performances of LiNi_0.5Mn_1.5O₄ was investigated by scanning electron microscopy, Fourier transform infrared, X-ray diffraction, and electrochemical method. The structure of both samples is confirmed as typical cubic spinel with Fd3m space group, whichever lithium salt is adopted. The grain size of LiNi_0.5Mn_1.5O₄ powder and its electrochemical behaviors are strongly affected by Li sources. For the samples prepared with lithium acetate, more spinel nucleation should form during the precalcination process, which was stimulated by the heat released from the combustion of extra organic acetate group. Therefore, the particle size of the obtained powder presents smaller average and wider distribution, which facilitates the initial discharge capacity and deteriorates the cycling performance. More seriously, there exists cation replacement of Li sites by transition metal elements, which causes channel block for Li ion transference and deteriorates the rate capability. The compound obtained with lithium hydroxide exhibits better electrochemical responses in terms of both cycling and rate properties due to higher crystallinity, moderate particle size, narrow size distribution and lower transition cation substitute content.     

Correlation between the structural,electrical and electrochemical performance of layered Li(Ni<Subscript>0.33</Subscript>Co<Subscript>0.33</Subscript>Mn<Subscript>0.33</Subscript>)O<Subscript>2</Subscript> for lithium ion battery

The Li(Ni_0.33Co_0.33Mn_0.33)O₂ (LNCMO) cathode material is prepared by poly(vinyl pyrrolidone) (PVP)-assisted sol-gel/hydrothermal and poly(ethylene glycol)-block-poly(propylene glycol)-block-poly (ethylene glycol) (Pluronic-P123)-assisted hydrothermal methods. The compound prepared by PVP-assisted hydrothermal method shows a comparatively higher electrical conductivity of ~2?×?10^?5 S cm^?1 and exhibits a discharge capacity of 152 mAh g^?1 in the voltage range of 2.5 to 4.4 V, for a C-rate of 0.2 C, whereas the compounds prepared by P123-assisted hydrothermal method and PVP-assisted sol-gel method show a total electrical conductivity in the order of 10^?6 S cm^?1 and result in poor electrochemical performance. The structural and electrical properties of LNCMO (active material) and its electrochemical performance are correlated. The difference in percentage of ionic and electronic conductivity contribution to the total electrical conductivity is compared by transference number studies. The cation disorder is found to be the limiting factor for the lithium ion diffusion as determined from ionic conductivity values.     

Enhanced electrochemical performance of submicron LiCoO<Subscript>2</Subscript> synthesized by polymer pyrolysis method

Submicron LiCoO₂ was synthesized by a polymer pyrolysis method using LiOH and Co(NO₃)₂ as the precursor compounds. Experimental results demonstrated that the powders calcined at 800 °C for 12 h appear as well-crystallized, uniform submicron particles with diameter of about 200 nm. As a result, the as-prepared LiCoO₂ electrode displayed excellent electrochemical properties, with an initial discharge capacity of 145.5 mAh/g and capacity retention of 86.1% after 50 cycles when cycled at 50 mA/g between 3.5 and 4.25 V. When cycled between 3.5 and 4.5 V, the discharge capacity increased to 177.9 mAh/g with capacity retention of 85.6% after 50 cycles.     

Electrospun Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript>/Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> composite nanofibers for enhanced high-rate lithium ion batteries

Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers with the mean diameter of ca. 60 nm have been synthesized via facile electrospinning. When the molar ratio of Li to Ti is 4.8:5, the Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers exhibit initial discharge capacity of 216.07 mAh g^?1 at 0.1 C, rate capability of 151 mAh g^?1 after being cycled at 20 C, and cycling stability of 122.93 mAh g^?1 after 1000 cycles at 20 C. Compared with pure Li₄Ti₅O₁₂ nanofibers and Li₂TiO₃ nanofibers, Li₄Ti₅O₁₂/Li₂TiO₃ composite nanofibers show better performance when used as anode materials for lithium ion batteries. The enhanced electrochemical performances are explained by the incorporation of appropriate Li₂TiO₃ which could strengthen the structure stability of the hosted materials and has fast Li⁺-conductor characteristics, and the nanostructure of nanofibers which could offer high specific area between the active materials and electrolyte and shorten diffusion paths for ionic transport and electronic conduction. Our new findings provide an effective synthetic way to produce high-performance Li₄Ti₅O₁₂ anodes for lithium rechargeable batteries.     

BiFeO<Subscript>3</Subscript>-coated spinel LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> with improved electrochemical performance as cathode materials for lithium-ion batteries

Spinel LiNi_0.5Mn_1.5O₄ cathode material is a promising candidate for next-generation rechargeable lithium-ion batteries. In this work, BiFeO₃-coated LiNi_0.5Mn_1.5O₄ materials were prepared via a wet chemical method and the structure, morphology, and electrochemical performance of the materials were studied. The coating of BiFeO₃ has no significant impact on the crystal structure of LiNi_0.5Mn_1.5O₄. All BiFeO₃-coated LiNi_0.5Mn_1.5O₄ materials exhibit cubic spinel structure with space group of Fd3m. Thin BiFeO₃ layers were successfully coated on the surface of LiNi_0.5Mn_1.5O₄ particles. The coating of 1.0 wt% BiFeO₃ on the surface of LiNi_0.5Mn_1.5O₄ exhibits a considerable enhancement in specific capacity, cyclic stability, and rate performance. The initial discharge capacity of 118.5 mAh g^?1 is obtained for 1.0 wt% BiFeO₃-coated LiNi_0.5Mn_1.5O₄ with very high capacity retention of 89.11% at 0.1 C after 100 cycles. Meanwhile, 1.0 wt% BiFeO₃-coated LiNi_0.5Mn_1.5O₄ electrode shows excellent rate performance with discharge capacities of 117.5, 110.2, 85.8, and 74.8 mAh g^?1 at 1, 2, 5, and 10 C, respectively, which is higher than that of LiNi_0.5Mn_1.5O₄ (97.3, 90, 77.5, and 60.9 mAh g^?1, respectively). The surface coating of BiFeO₃ effectively decreases charge transfer resistance and inhibits side reactions between active materials and electrolyte and thus induces the improved electrochemical performance of LiNi_0.5Mn_1.5O₄ materials.     

Natural graphite enhanced the electrochemical performance of Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> cathode material for lithium ion batteries

Natural graphite treated by mechanical activation can be directly applied to the preparation of Li₃V₂(PO₄)₃. The carbon-coated Li₃V₂(PO₄)₃ with monoclinic structure was successfully synthesized by using natural graphite as carbon source and reducing agent. The amount of activated graphite is optimized by X-ray diffraction, scanning electron microscope, transmission electron microscope, Raman spectrum, galvanostatic charge/discharge measurements, cyclic voltammetry, and electrochemical impedance spectroscopy tests. Our results show that Li₃V₂(PO₄)₃ (LVP)-10G exhibits the highest initial discharge capacity of 189 mAh g^?1 at 0.1 C and 162.9 mAh g^?1 at 1 C in the voltage range of 3.0–4.8 V. Therefore, natural graphite is a promising carbon source for LVP cathode material in lithium ion batteries.     

Nearly monodispersed LiFePO<Subscript>4</Subscript>F nanospheres as cathode material for lithium ion batteries

Tavorite-structured lithium transition metal fluorophosphates have been considered as a good alternative to olivine-type cathode for lithium-ion batteries due to its exceptional ionic conductivity and excellent thermal stability. In this work, nearly monodisperse LiFePO₄F nanospheres with high purity are successfully synthesized by a solid-state route associated with chemically induced precipitation method for the first time. The synthesized LiFePO₄F presents nearly monodisperse nanospheres particles with average particle size of ~?500 nm. Cyclic voltammetry data exhibit a clear indication of the Fe³⁺/Fe²⁺ redox couple that involves a two-phase transition. Its electrochemical behaviors are examined by galvanostatic charge-discharge. The results show that the initial discharge capacity is 110.2 mAh g^?1 at 0.5 C, after 200 cycles is still retained 104.0 mAh g^?1 with the retention rate of 94.4%. The excellent cycle performance is mainly attributed to the uniform nanospheres-like morphology which is not only beneficial to shorten the transport distance of ions and electrons, but also improve the interface area between electrode and electrolyte, and thus improve the kinetics of Li ions.     

Li<Subscript>0.99</Subscript>Ti<Subscript>0.01</Subscript>FePO<Subscript>4</Subscript>/C composite as cathode material for lithium ion battery

Three kinds of LiFePO₄ materials, mixed with carbon (as LiFePO₄/C), doped with Ti (as Li_0.99Ti_0.01FePO₄), and treated both ways (as Li_0.99Ti_0.01FePO₄/C composite), were synthesized via ball milling by solid-state reaction method. The crystal structure and electrochemical behavior of the materials were investigated using X-ray diffraction, SEM, TEM, cyclic voltammetry, and charge/discharge cycle measurements. It was found that the electrochemical behavior of LiFePO₄ could be increased by carbon coating and Ti-doping methods. Among the materials, Li_0.99Ti_0.01FePO₄/C composite presents the best electrochemical behavior, with an initial discharge capacity of 154.5 mAh/g at a discharge rate of 0.2 C, and long charge/discharge cycle life. After 120 cycles, its capacity remains at 92% of the initial capacity. The Li_0.99Ti_0.01FePO₄/C composite developed here can be used as the cathode material for lithium ion batteries.     

Co<Subscript>2</Subscript>(OH)<Subscript>3</Subscript>Cl xerogels with 3D interconnected mesoporous structures as a novel high-performance supercapacitor material

Co₂(OH)₃Cl xerogel interconnected mesoporous structures have been prepared by a facile one pot sol-gel process and heat treated at 200 and 400 °C. All samples are studied for their morphology, structure, and electrochemical stability upon cycling. The specific capacitance of the as-prepared Co₂(OH)₃Cl from single electrode study is 450 F/g, when the electrodes are cycled in 3 M KOH at a specific current 2 A/g. Interestingly, capacity retention after 500 and 1000 cycles is about 92 and 75 %, respectively. Sample heated at 200 °C exhibits 308 F/g at 2 A/g and that heated at 400 °C shows only 32 F/g at 0.2 A/g. With an increase in preparation temperature, amorphous Co₂(OH)₃Cl is converted to crystalline Co₃O₄ phases with lower electrochemical performance. In full cell study, as-prepared Co₂(OH)₃Cl showed a capacity of about 49 F/g as asymmetric capacitor and 32 F/g as symmetric capacitor at 2 A/g current density. Co₂(OH)₃Cl being a novel porous material with merits of homogeneous porosity, high surface area, and an interconnected three dimensional (3D) structure exhibits considerably high capacitance. With a significant specific capacity and electrochemical stability, the synthesized material is a novel potential candidate for supercapacitors.

Open image in new window

Graphical abstract ?

     

Comparing the electrochemical properties of pure phase Zn<Subscript>2</Subscript>SnO<Subscript>4</Subscript> and composite Zn<Subscript>2</Subscript>SnO<Subscript>4</Subscript>/C

Compound Zn₂SnO₄ was synthesized by a hydrothermal method in which SnCl₄ · 5H₂O, ZnCl₂ and N₂H₄ · H₂O were used as reactants. Composite Zn₂SnO₄/C was then synthesized through a carbothermic reduction process using the as-prepared Zn₂SnO₄ and glucose as reactants. Comparing to the pure Zn₂SnO₄, some improved electrochemical properties were obtained for composite Zn₂SnO₄/C. When doped with 15% glucose, the composite Zn₂SnO₄/C showed the best electrochemical performance. Its first discharge capacity was about 1500 mA h g⁻¹, with a capacity retain of 500 mA h g⁻¹ in the 40th cycle at a constant current density of 100 mA/g in the voltage range of 0.05–3.0 V. There were also some differences displayed in their cyclic voltammogram.     

Electrochemical properties of nano-crystalline LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> synthesized by polymer-pyrolysis method

LiNi_0.5Mn_1.5O₄ powders were prepared through polymer-pyrolysis method. XRD and TEM analysis indicated that the pure spinel structure was formed at around 450 °C due to the very homogeneous intermixing of cations at the atomic scale in the starting precursor in this method, while the well-defined octahedral crystals appeared at a relatively high calcination temperature of 900 °C with a uniform particle size of about 100 nm. When cycled between 3.5 and 4.9 V at a current density of 50 mA/g, the as prepared LiNi_0.5Mn_1.5O₄ delivered an initial discharge capacity of 112.9 mAh/g and demonstrated an excellent cyclability with 97.3% capacity retentive after 50 cycles.