BiFeO<Subscript>3</Subscript>-coated spinel LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> with improved electrochemical performance as cathode materials for lithium-ion batteries

Spinel LiNi_0.5Mn_1.5O₄ cathode material is a promising candidate for next-generation rechargeable lithium-ion batteries. In this work, BiFeO₃-coated LiNi_0.5Mn_1.5O₄ materials were prepared via a wet chemical method and the structure, morphology, and electrochemical performance of the materials were studied. The coating of BiFeO₃ has no significant impact on the crystal structure of LiNi_0.5Mn_1.5O₄. All BiFeO₃-coated LiNi_0.5Mn_1.5O₄ materials exhibit cubic spinel structure with space group of Fd3m. Thin BiFeO₃ layers were successfully coated on the surface of LiNi_0.5Mn_1.5O₄ particles. The coating of 1.0 wt% BiFeO₃ on the surface of LiNi_0.5Mn_1.5O₄ exhibits a considerable enhancement in specific capacity, cyclic stability, and rate performance. The initial discharge capacity of 118.5 mAh g^?1 is obtained for 1.0 wt% BiFeO₃-coated LiNi_0.5Mn_1.5O₄ with very high capacity retention of 89.11% at 0.1 C after 100 cycles. Meanwhile, 1.0 wt% BiFeO₃-coated LiNi_0.5Mn_1.5O₄ electrode shows excellent rate performance with discharge capacities of 117.5, 110.2, 85.8, and 74.8 mAh g^?1 at 1, 2, 5, and 10 C, respectively, which is higher than that of LiNi_0.5Mn_1.5O₄ (97.3, 90, 77.5, and 60.9 mAh g^?1, respectively). The surface coating of BiFeO₃ effectively decreases charge transfer resistance and inhibits side reactions between active materials and electrolyte and thus induces the improved electrochemical performance of LiNi_0.5Mn_1.5O₄ materials.     

Electrochemical properties of nano-crystalline LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> synthesized by polymer-pyrolysis method

LiNi_0.5Mn_1.5O₄ powders were prepared through polymer-pyrolysis method. XRD and TEM analysis indicated that the pure spinel structure was formed at around 450 °C due to the very homogeneous intermixing of cations at the atomic scale in the starting precursor in this method, while the well-defined octahedral crystals appeared at a relatively high calcination temperature of 900 °C with a uniform particle size of about 100 nm. When cycled between 3.5 and 4.9 V at a current density of 50 mA/g, the as prepared LiNi_0.5Mn_1.5O₄ delivered an initial discharge capacity of 112.9 mAh/g and demonstrated an excellent cyclability with 97.3% capacity retentive after 50 cycles.     

Effect of the preparation method of the cathode material LiNi<Subscript>0.33</Subscript>Mn<Subscript>0.33</Subscript>Co<Subscript>0.33</Subscript>O<Subscript>2</Subscript> on the electrochemical characteristics of a lithium ion cell

Complex metal oxides with the composition LiNi_0.33Mn_0.33Co_0.33O₂ prepared by various methods: sol–gel method, solid-phase method, and thermal destruction of metal-containing compounds in oil were studied. The results of elemental analysis, TGA/DSC, powder X-ray diffraction, SEM, TEM, as well as the results of electrochemical testing of the cathodes based on the obtained materials are presented. The complex metal oxides LiNi_0.33Mn_0.33Co_0.33O₂ prepared by sol–gel processes and thermal destruction of metal-containing compounds in oil consist of primary nanosized crystallites with an average size of 90 nm covered by a nanometer carbon layer, which improves the electrochemical characteristics of lithium ion batteries.     

Synthesis and electrochemical properties of yttrium-doped LiMn<Subscript>0.98</Subscript>Y<Subscript>0.02</Subscript>O<Subscript>2</Subscript> for lithium secondary batteries

Yttrium-doped lithium manganese oxide (LiMn_0.98Y_0.02O₂) was prepared by ion exchange of lithium for sodium in NaMn_0.98Y_0.02O₂ precursors obtained by using rheological phase reaction method. This material had small particle size, which was composed of grain size of about 100 nm. Especially, LiMn_0.98Y_0.02O₂ delivered the initial discharge capacity of about 191 mA h g⁻¹ at room temperature when cycled between 2.0 and 4.4 V vs Li/Li⁺. Moreover, it showed an excellent cycling behavior, its specific capacity remained above 173 mA h g⁻¹ after 20 cycles, and the material did not transform into spinel structure during the electrochemical cycling according to the cyclic voltammograms and X-ray powder diffraction. The electrochemical results revealed that the doping of Y³⁺ improved the performance of LiMnO₂ considerably.     

Glycine-assisted combustion synthesis and electrochemical behavior of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.5</Subscript>O<Subscript>2</Subscript> nanoparticles under microwave irradiation

Layered LiNi_0.5Mn_0.5O₂ nanoparticles have been successfully prepared by the glycine-assisted combustion method under microwave irradiation. The exothermic reaction can generate a large quantity of heat rapidly leading to the formation and crystallization of LiNi_0.5Mn_0.5O₂. From the X-ray diffraction and scanning electronic microscopy results, the resulting powders have a well-developed layered structure and average particle-size is about 80 nm. The chemical composition analysis and electrochemical characteristics of the obtained LiNi_0.5Mn_0.5O₂ nanoparticles as cathode material for rechargeable lithium-ion battery were also investigated. The improved electrochemical performances of the layered LiNi_0.5Mn_0.5O₂ nanoparticles might be ascribed to the nanostructure of the powders and the unique combustion synthesis under microwave irradiation.     

Co-precipitation spray-drying synthesis and electrochemical performance of stabilized LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode materials

In this paper, the LiNi_0.5Mn_1.5O₄ cathode materials of lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining process. The use of a spray-drying process to form particles, followed by a calcination treatment at the optimized temperature of 750 °C to produce spherical LiNi_0.5Mn_1.5O₄ particles with a cubic crystal structure, a specific surface area of 60.1 m² g^?1, a tap density of 1.15 g mL^?1, and a specific capacity of 132.9 mAh g^?1 at 0.1 C. The carbon nanofragment (CNF) additives, introduced into the spheres during the co-precipitation spray-drying period, greatly enhance the rate performance and cycling stability of LiNi_0.5Mn_1.5O₄. The sample with 1.0 wt.% CNF calcined at 750 °C exhibits a maximum capacity of 131.7 mAh g^?1 at 0.5 C and a capacity retention of 98.9% after 100 cycles. In addition, compared to the LiNi_0.5Mn_1.5O₄ material without CNF, the LiNi_0.5Mn_1.5O₄ with CNF demonstrates a high-rate capacity retention that increases from 69.1% to 95.2% after 100 cycles at 10 C, indicating an excellent rate capability. The usage of CNF and the synthetic method provide a promising choice for the synthesis of a stabilized LiNi_0.5Mn_1.5O₄ cathode material.

Open image in new window

Graphical Abstract Micro/nanostructured LiNi_0.5Mn_0.5O₄ cathode materials with enhanced electrochemical performances for high voltage lithium-ion batteries are synthesized by a co-precipitation spray-drying and calcining routine and using carbon nanofragments (CNFs) as additive.

     

锰源对燃烧法制备5V级正极材料LiNi0.5Mn1.5O4的影响

以硝酸锰和醋酸锰,采用蔗糖燃烧法制备锂离子电池正极材料LiNi0.5Mn1.5O4通过XRD、SEM、粒径分布测试、循环伏安、恒流充放电测试以及交流阻抗等方法,研究了醋酸锰和硝酸锰对产物的结构、形貌、粒径及电化学性能的影响。XRD测试结果表明样品的结构都为立方尖晶石型,属于Fd3m空间群。不同的锰源对材料的粒径及粒径分布有很大的影响。以醋酸锰为原料制得的材料的粒径较小并且分布更均匀,有利于锂离子的脱出和嵌入从而提高电化学性能。以醋酸锰为锰源制得的LiNi0.5Mn1.5O4在3.6~5.2 V的充放电电压范围内的电化学性能更好,1C(1C=140.0 mA.g-1)倍率的首次放电容量为144.5 mAh.g-1,循环100周后容量保持率为96%,在3C,5C,10C以及20C的放电容量分别为136.3,132.0,124.7以及96.6 mAh.g-1。     

Effect of lithium boron oxide glass coating on the electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript>

The effect of the lithium boron oxide glass coating on the electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂ has been investigated via solution method. The morphology, structure, and electrochemical properties of the bare and coated LiNi_1/3Co_1/3Mn_1/3O₂ are characterized by scanning electron microscopy, X-ray diffraction, electrochemical impedance spectroscopy, and charge–discharge tests. The results showed that the lattice structure of LiNi_1/3Co_1/3Mn_1/3O₂ is not changed after coating. The coating sample shows good high-rate discharge performance (148 mAh g⁻¹ at 5.0 C rate) and cycling stability even at high temperature (with the capacities retention about 99% and 87% at room and elevated temperature after 50 cycles). The Li⁺ diffusion coefficient is also largely improved, while the charge transfer resistance, side reactions within cell, and the erosion of Hydrofluoric Acid all reduced. Consequently, the good electrochemical performances are obtained.     

Improvement of the electrochemical properties of a LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode material formed by a new solid-state synthesis method

In order to avoid the shortcomings of large particle size and poor uniformity of material synthesized by the traditional solid-state method, this paper utilizes a simple improvement of calcination process (i.e., calcination–milling–recalcination) based on the traditional solid-state synthesis to successfully prepare a large number of well-distributed, micrometer-sized, spherical secondary LiNi_0.5Mn_1.5O₄ particles. Each particle is composed of nano- and/or sub-micrometer-sized grains. Results of the electrochemical performance tests show that the material exhibits a remarkable cycle performance and rate capability compared with that obtained from traditional synthesis method; the spherical LiNi_0.5Mn_1.5O₄ particles can deliver a large capacity of 135.8 mAh g^?1 at a 1 C discharge rate with a high retention of 77 % after 741 cycles and a good capacity of 105.9 mAh g^?1 at 10 C. Cyclic voltammetry measurements confirm that the significantly improved electrochemical properties are due to enhanced electronic conductivity and lithium-ion diffusion coefficient resulting from the optimized morphology and particle size. This improved method is more suitable for mass production.     

Synthesis and electrochemical properties of Li-rich Li[Ni<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>]O<Subscript>2</Subscript> for pouch-typed cell

Layered transition metal oxide LiNi _x Co _y MnzO₂ cathode materials with different Li amount were successfully synthesized via co-precipitation method. Monodispersed Li[Ni_0.5Co_0.2Mn_0.3]O₂ and Li-rich Li_1.1[Ni_0.5Co_0.2Mn_0.3]O₂ spherical agglomeration consisted of secondary particles, which is favorable for the higher tap-density of materials, can be easily obtained. The pouch-typed cells with obtained materials were assembled to investigate electrochemical performance at level of full-cell. The results show that the assembled pouch-typed full-cells with Li-rich sample present higher capacity, better rate capability and cycle life.     

Effects of Mg,Al Co-doping into Mn site on electrochemical performance of LiNi<Subscript>0.5</Subscript>Co<Subscript>0.2</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript>

In order to study the influence of multiple ions doping into single-site on the structure and electrochemical properties of Ni-rich layered-structure cathode material LiNi_0.5Co_0.2Mn_0.3O₂, the coprecipitation of hydroxides was applied to synthesize Mg, Al co-doped cathode material LiNi_0.5Co_0.2Mn_0.3–x Mg_1/2x Al_1/2x O₂ (x = 0.00, 0.01, 0.02, 0.04) in this paper. Morphology and structure, kinetic parameter, impedance and electrochemical performance of the material were respectively characterized by SEM, XRD, CV, EIS and galvanostatic charge/discharge test. The results of comprehensive analysis showed that the properties of material were improved obviously when the amount of doping was 0.02. At this amount of doping, the corresponding material has smaller cation mixing, higher hexagonal ordering of layered-structure, larger Li⁺ ion diffusion coefficients which are 2.444 × 10^–10 and 4.186 × 10^–10 cm² s^–1 for Li+ intercalation and deintercalation respectively, smaller impedance which is 33.93 Ω, higher specific capacity of first-discharge which is 168.01 mA h g^–1 and higher capacity retention rate which is up to 95.06% after 20 cycles at 0.5 C (100 mA g^–1).     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Influence of Li source on tap density and high rate cycling performance of spherical Li[Ni<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>]O<Subscript>2</Subscript> for advanced lithium-ion batteries

Spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode materials with different microstructure have been prepared by a continuous carbonate co-precipitation method using LiOH⋅H₂O, Li₂CO₃, CH₃COOLi⋅2H₂O and LiNO₃ as lithium source. The effects of Li source on the physical and electrochemical properties of Li[Ni_1/3Co_1/3Mn_1/3]O₂ are investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical measurements. The results show that the morphology, tap density and high rate cycling performance of Li[Ni_1/3Co_1/3Mn_1/3]O₂ spherical particles are strongly affected by Li source. Among the four Li sources used in this study, LiOH⋅H₂O is beneficial to enhance the tap density of Li[Ni_1/3Co_1/3Mn_1/3]O₂, and the tap density of as-prepared sample reaches 2.32 g cm⁻³. Meanwhile, Li₂CO₃ is preferable when preparing the Li[Ni_1/3Co_1/3Mn_1/3]O₂ with high rate cycling performance, upon extended cycling at 1 and 5C rates, 97.5% and 92% of the initial discharge capacity can be maintained after 100 cycles.     

Effects of Nb substitution on structure and electrochemical properties of LiNi<Subscript>0.7</Subscript>Mn<Subscript>0.3</Subscript>O<Subscript>2</Subscript> cathode materials

Nb-doped cathode materials with the formula Li(Ni_0.7Mn_0.3)_1?xNb_xO₂ (x?=?0, 0.01, 0.02, 0.03, 0.04) have been prepared successfully by calcining the mixtures of LiOH·H₂O, Nb₂O₅, and Ni_0.7Mn_0.3(OH)₂ precursor formed through a simple continuous co-precipitation method. The effects of Nb substitution on the crystal structure and electrochemical properties of LiNi_0.7Mn_0.3O₂ were studied systematically by X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and various electrochemical measurements. The results show that the lattice parameters of the Nb substitution LiNi_0.7Mn_0.3O₂ samples are slightly larger than that of pure LiNi_0.7Mn_0.3O₂, and the basic α-NaFeO₂ layered structure does not change with the Nb doping. What’s more, better morphology, lower resistance, and good cycle stability were obtained after Nb substitution. In addition, CV test exhibits that Nb doping results in lower electrode polarization and XPS results indicate that the valence of Mn kept constant but the component of Ni³⁺ decreased after doping. All the results indicate that Nb doping in LiNi_0.7Mn_0.3O₂ is a promising method to improve the properties of Ni-rich lithium-ion batteries positive-electrode materials.     

High-Temperature X-Ray Diffraction Investigation of the Decomposition Process in Manganese-Gallium Spinel Mn<Subscript>1.5</Subscript>Ga<Subscript>1.5</Subscript>O<Subscript>4</Subscript>

The stability of spinel-type mixed Mn_1.5Ga_1.5O₄ oxide prepared in an inert medium (1000 °C, Ar) is studied by thermogravimetry and high-temperature X-ray diffraction in air in a wide temperature range 30–1000 °C. On heating, reversible decomposition processes of initial spinel are observed. From 30 °C to 600 °C oxygen atoms attach to the surface layer of initial Mn_1.5Ga_1.5O₄ spinel to form a new phase distinct from parent oxide by the oxygen stoichiometry (cation vacancies are formed). The product of decomposition is two oxides: Mn_1.5Ga_1.5O₄ and Mn_1.5–xGa_1.5–x[·]_xO₄. On the contrary, above 600 °C a loss of oxygen occurs, the concentration of cation vacancies decreases in Mn_1.5–xGa_1.5–x[·]_xO₄, and the reverse process of single phase oxide crystallization takes place. At 1000 °C the spinel phase forms again whose composition is similar to that of the initial parent phase Mn_1.5Ga_1.5O₄. On cooling the decomposition of this phase is again observed due to oxygen attachment.     

Hydride lithiation of spinels LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>

Undoped lithiation of stoichiometric spinel using lithium hydride LiH up to the composition Li_2.25Mn₂O₄ was performed. A homogeneous material with a given Li: Mn ratio was obtained by mechanochemical activation with sequential annealing of a LiMn₂O₄–LiH mixture in a high-purity argon atmosphere and then in air or oxygen at 373–553 K.     

Electrochemical properties of submicro-sized layered LiNi0.5Mn0.5O2

Submicro-sized layered LiNi_0.5Mn_0.5O₂ was synthesized via an improved solid-state reaction, in which at first a precursor mixed by nickel manganese double hydroxide with lithium hydroxide solution was prepared in order to make the fully contact between these materials, and then was calcined at different temperatures. The heat treatment process and the crystal structure of materials were investigated by DTA, TGA, and XRD methods. The SEM images show that the particles of layered LiNi_0.5Mn_0.5O₂ are submicrometer in size. It was found that the layered LiNi_0.5Mn_0.5O₂ synthesized at 750 °C for 24 h in oxygen atmosphere presents the best electrochemical performance, which delivers an initial discharge capacity of 153 mAh/g in the charge/discharge potential region (vs. Li) of 2.5–4.3 V, and exhibits good cycle stability.     

Li3PO4‐Coated LiNi0.5Mn1.5O4: A Stable High‐Voltage Cathode Material for Lithium‐Ion Batteries

LiNi_0.5Mn_1.5O₄ is regarded as a promising cathode material to increase the energy density of lithium‐ion batteries due to the high discharge voltage (ca. 4.7 V). However, the interface between the LiNi_0.5Mn_1.5O₄ cathode and the electrolyte is a great concern because of the decomposition of the electrolyte on the cathode surface at high operational potentials. To build a stable and functional protecting layer of Li₃PO₄ on LiNi_0.5Mn_1.5O₄ to avoid direct contact between the active materials and the electrolyte is the emphasis of this study. Li₃PO₄‐coated LiNi_0.5Mn_1.5O₄ is prepared by a solid‐state reaction and noncoated LiNi_0.5Mn_1.5O₄ is prepared by the same method as a control. The materials are fully characterized by XRD, FT‐IR, and high‐resolution TEM. TEM shows that the Li₃PO₄ layer (<6 nm) is successfully coated on the LiNi_0.5Mn_1.5O₄ primary particles. XRD and FT‐IR reveal that the synthesized Li₃PO₄‐coated LiNi_0.5Mn_1.5O₄ has a cubic spinel structure with a space group of Fd$\bar 3$ m, whereas noncoated LiNi_0.5Mn_1.5O₄ shows a cubic spinel structure with a space group of P4₃32. The electrochemical performance of the prepared materials is characterized in half and full cells. Li₃PO₄‐coated LiNi_0.5Mn_1.5O₄ shows dramatically enhanced cycling performance compared with noncoated LiNi_0.5Mn_1.5O₄.     

Towards high-performance cathode materials for lithium-ion batteries: Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-coated LiNi<Subscript>0.8</Subscript>Co<Subscript>0.15</Subscript>Zn<Subscript>0.05</Subscript>O<Subscript>2</Subscript>

Zn-doped LiNi_0.8Co_0.2O₂ exhibits impressive electrochemical performance but suffers limited cycling stability due to the relative large size of irregular and bare particle which is prepared by conventional solid-state method usually requiring high calcination temperature and prolonged calcination time. Here, submicron LiNi_0.8Co_0.15Zn_0.05O₂ as cathode material for lithium-ion batteries is synthesized by a facile sol-gel method, which followed by coating Al₂O₃ layer of about 15 nm to enhance its electrochemistry performance. The as-prepared Al₂O₃-coated LiNi_0.8Co_0.15Zn_0.05O₂ cathode delivers a highly reversible capacity of 182 mA h g^?1 and 94% capacity retention after 100 cycles at a current rate of 0.5 C, which is much superior to that of bare LiNi_0.8Co_0.15Zn_0.05O₂ cathode. The enhanced electrochemistry performance can be attributed to the Al₂O₃-coated protective layer, which prevents the direct contact between the LiNi_0.8Co_0.15Zn_0.05O₂ and electrolyte. The escalating trend of Li-ion diffusion coefficient estimated form electrochemical impedance spectroscopic (EIS) also indicate the enhanced structural stability of Al₂O₃-coated LiNi_0.8Co_0.15Zn_0.05O₂, which rationally illuminates the protection mechanism of the Al₂O₃-coated layer.     

Synthesis of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> nanoparticles by modified Pechini method and their enhanced rate capability

Layered LiNi_1/3Co_1/3Mn_1/3O₂ nanoparticles were prepared by modified Pechini method and used as cathode materials for Li-ion batteries. The pyrolytic behaviors of the foamed precursors were analyzed by use of simultaneous thermogravimetric and differential thermal analysis (TG-DTA). Structure, morphology and electrochemical performance characterization of the samples were investigated by X-ray diffraction (XRD), field emission scanning electron macroscopy(SEM), Brunauer-Emmett-Teller (BET) specific surface area and charge–discharge tests. The results showed that the samples prepared by modified Pechini method caclined at 900 °C for 10 h were indexed to pure LiNi_1/3Co_1/3Mn_1/3O₂ with well hexagonal structure. The particle size was in a range of 100–300 nm. The specific surface area was larger than that of the as-obtained sample by Pechini method. Initial discharge capacity of 163.8 mAh/g in the range 2.8–4.4 V (vs. Li/Li⁺) and at 0.1C for LiNi_1/3Co_1/3Mn_1/3O₂ prepared by modified Pechini method was obtained, higher than that of the sample prepared by Pechini method (143.5 mAh/g). Moreover, the comparison of electrochemical results at different current rates indicated that the sample prepared by modified Pechini method exhibited improved rate capability.