Mid-infrared InAsSb-based nBn photodetectors with AlGaAsSb barrier layers – Grown on GaAs,using an interfacial misfit array,and on native GaSb

InAsSb-based nBn photodetectors were fabricated on GaAs, using the interfacial misfit (IMF) array growth mode, and on native GaSb. At −0.1 V operating bias, 200 K dark current densities of 1.4 × 10⁻⁵ A cm⁻² (on GaAs) and 4.8 × 10⁻⁶ A cm⁻² (on GaSb) were measured. At the same temperature, specific detectivity (D^*) figures of 1.2 × 10¹⁰ Jones (on GaAs) and 7.2 × 10¹⁰ Jones (on GaSb) were calculated. Arrhenius plots of the dark current densities yielded activation energies of 0.37 eV (on GaAs) and 0.42 eV (on GaSb). These values are close to the 4 K bandgap of the absorption layers (0.32–0.35 eV) indicating diffusion limited dark currents and small valence band offsets. Significantly, these devices could be used for mid-infrared focal plane arrays operating within the temperature range of cost-effective thermoelectric coolers.     

Effect of temperature on the current–voltage characteristics of GaAs/AlGaAs quantum cascade photodetectors

Transport of electrons within a quantum cascade photodetector structure takes place with the help of the scattering of electrons by phonons. By calculating scattering rates of the electrons mediated by longitudinal optical phonons (the dominant scattering mechanism), current–voltage characteristic of a quantum cascade photodetector is calculated. The results indicate that with the increase of bias voltage dark current increases rapidly, then the increase becomes slow at higher voltages, whilst photocurrent remains approximately constant with only slight variations in its magnitude. With the increase of temperature from 80 K to 160 K dark current increases by about two orders of magnitude while photocurrent varies slightly, so that at the illuminating power of 1 mW/m² photocurrent density increases in mean from 1.10×10⁻⁹ A/cm² at 80 K to 1.14×10⁻⁹ A/cm² at 160 K and then decreases to 1.03×10⁻⁹ A/cm² at 240 K. Thus the responsivity of the detector varies only slightly with temperature. However owing to the decrease in the resistivity of the photodetector with the increase of temperature, Johnson noise limited detectivity decreases considerably.     

Improving the performance of a far-infrared quantum-ring-based photodetector utilizing asymmetric multi-barrier resonant tunneling

In this paper, a novel structure for quantum ring inter-subband photodetectors (QRIP) is proposed to reduce its dark current. Some additional layers including asymmetric multi-barrier resonant tunneling (AMBRT) in absorption region layers are exploited to provide near unity tunneling probability for generated photocurrents and completely reject thermally generated electrons. AMBRT structure consists of three asymmetric AlGaAs barriers and two InGaAs wells which are designed for operation wavelength of generated photocurrents by absorption of 20 μm. Simulation results show that AMBRT can considerably reduce the dark current compared to previously proposed resonant tunneling structure about three orders of magnitude. As a consequent, higher specific detectivity for AMBRT-QRIP is obtained in the order of ∼10¹¹ cm Hz^1/2/W at 100 K.     

Performance improvement of long-wave infrared InAs/GaSb strained-layer superlattice detectors through sulfur-based passivation

We report on effective sulfur-based passivation treatments of type-II InAs/GaSb strained layer superlattice detectors (100% cut-off wavelength is 9.8 μm at 77 K). The electrical behavior of detectors passivated by electrochemical sulfur deposition (ECP) and thioacetamide (TAM) was evaluated for devices of various sizes. ECP passivated detectors with a perimeter-to-area ratio of 1600 cm^?1 exhibited superior performance with surface resistivity in excess of 10⁴ Ω cm, dark current density of 2.7 × 10^?3 A/cm², and specific detectivity improved by a factor of 5 compared to unpassivated devices (V_Bias =  ? 0.1 V, 77 K).     

InGaAsP/InP photodetectors targeting on 1.06 μm wavelength detection

InP-based InGaAsP photodetectors targeting on 1.06 μm wavelength detection have been grown by gas source molecular beam epitaxy and demonstrated. For the detector with 200 μm mesa diameter, the dark current at 10 mV reverse bias and R₀A are 8.89 pA (2.2 × 10⁻⁸ A/cm²) and 3.9 × 10⁵ Ω cm² at room temperature. The responsivity and detectivity of the InGaAsP detector are 0.30 A/W and 1.45 × 10¹² cm Hz^1/2 W⁻¹ at 1.06 μm wavelength. Comparing to the reference In_0.53Ga_0.47As detector, the dark current of this InGaAsP detector is about 570 times lower and the detectivity is more than ten times higher, which agrees well with the theoretical estimation.     

Modeling of electrical and optical characteristics of near room-temperature CdS/ZnSe based NIR photodetectors

Results of modeled photodetector characteristics in (CdS/ZnSe)/BeTe multi-well diode with p–i–n polarity are reported. The dark current density (J–V) characteristics, the temperature dependence of zero-bias resistance area product (R₀A), the dynamic resistance as well as bias dependent dynamic resistance (R_d) and have been analyzed to investigate the mechanisms limiting the electrical performance of the modeled photodetectors. The quantum efficiency, the responsivity and the detectivity have been also studied as function of the operating wavelength. The suitability of the modeled photodetector is demonstrated by its feasibility of achieving good device performance near room temperature operating at 1.55 μm wavelength required for photodetection in optical communication. Quantum efficiency of ∼95%, responsivity ∼0.6 A/W and D^* ∼ 5.7 × 10¹⁰ cm Hz^1/2/W have been achieved at 300 K in X BeTe conduction band minimum.     

Design and modelling of high-operating temperature MWIR HgCdTe nBn detector with n- and p-type barriers

The paper present the numerical analysis of the electrical and optical properties of the mid-wave infrared (MWIR) HgCdTe nBn type detectors with a 3.4 μm cut-off wavelength (at 50% of the initial rise in the response) operating at 230 K. The analysed n⁺/B/n/N⁺ structure consists of four HgCdTe layers with n- and p-type barriers. Different structural parameters, as well as compositional and dopant profiles obtained in molecular beam epitaxy (MBE) and metal organic chemical vapour deposition (MOCVD) techniques were modelled with emphasis on conduction band and valence band-offset which determines the proper construction of the nBn type devices. The barrier must prevent the flow of the electron current from the cap region to the absorber while simultaneously ensure the flow and collection of thermally and optically generated holes from the absorber to the cap region. It was shown that proper p-type doping of the barrier reduce the valence band-offset and increase the offset in the conduction band leading to the optimal detector architecture.Theoretical results were related to the experimental data of the MWIR n⁺/B/n/N⁺ photodetectors grown by MOCVD. Dark currents of the first fabricated devices are limited by undesirable iodine diffusion from cap layer to the barrier. However, the nBn architecture might be a promising solution for HgCdTe infrared detectors grown by MOCVD, mainly due to the possibility of in situ acceptor doping of the barrier.     

Bias-selectable mid-/long-wave dual band infrared focal plane array based on Type-II InAs/GaSb superlattice

In this paper, a mid-/long-wave dual-band detector which combined PπMN structure and unipolar barrier was developed based on type-II InAs/GaSb superlattice. A relevant 320 × 256 focal plane array (FPA) was fabricated. Unipolar barrier and PπMN structure in our dual band detector structure were used to suppress cross-talk and dark current, respectively. The two channels, with respective 50% cut-off wavelength at 4.5 μm and 10 μm were obtained. The peak quantum efficiency (QE) of mid wavelength infrared (MWIR) band and long wavelength infrared (LWIR) band are 53% at 3.2 μm under no bias voltage and 40% at 6.4 μm under bias voltage of −170 mV, respectively. And the dark current density under 0 and −170 mV of applied bias are 1.076 × 10⁻⁵ A/cm² and 2.16 × 10⁻⁴ A/cm². The specific detectivity of MWIR band and LWIR band are 2.15 × 10¹² cm·Hz^1/2/W at 3.2 μm and 2.31 × 10¹⁰ cm·Hz^1/2/W at 6.4 μm, respectively, at 77 K. The specific detectivity of LWIR band maintains above 10¹⁰ cm·Hz^1/2/W at the wavelength range from 4.3 μm to 10.2 μm under −170 mV. The cross-talk, selectivity parameter at 3.0 μm, about 0.14 was achieved under bias of −170 mV. Finally, the thermal images were taken by the fabricated FPA at 77 K.     

Performance of mid-wave T2SL detectors with heterojunction barriers

A heterojunction T2SL barrier detector which effectively blocks majority carrier leakage over the pn-junction was designed and fabricated for the mid-wave infrared (MWIR) atmospheric transmission window. The layers in the barrier region comprised AlSb, GaSb and InAs, and the thicknesses were selected by using k · P-based energy band modeling to achieve maximum valence band offset, while maintaining close to zero conduction band discontinuity in a way similar to the work of Abdollahi Pour et al. [1] The barrier-structure has a 50% cutoff at 4.75 μm and 40% quantum efficiency and shows a dark current density of 6 × 10⁻⁶ A/cm² at −0.05 V bias and 120 K. This is one order of magnitude lower than for comparable T2SL-structures without the barrier. Further improvement of the (non-surface related) bulk dark current can be expected with optimized doping of the absorber and barrier, and by fine tuning of the barrier layer design. We discuss the effect of barrier doping on dark current based on simulations. A T2SL focal plane array with 320 × 256 pixels, 30 μm pitch and 90% fill factor was processed in house using a conventional homojunction p–i–n photodiode architecture and the ISC9705 readout circuit. High-quality imaging up to 110 K was demonstrated with the substrate fully removed.     

High quality mid-wavelength infrared InAs/GaSb superlattices by exploring the optimum molecular beam epitaxy growth process

In this paper we report on the growth of mid-wavelength infrared superlattice materials by molecular beam epitaxy. We focused on the effects of process parameters, such as arsenic beam equivalent pressure and shutter sequences, on the key material properties, such as the lattice mismatch and the surface morphology. Though a smaller As beam equivalent pressure helps to reduce the lattice mismatch between the superlattice and the GaSb substrate, the As beam equivalent pressure itself has a lower limit below which the material’s surface morphology will degrade. To achieve fully lattice-matched superlattice materials, a novel shutter sequence in the growth process was designed. With well-designed interface structures, a high quality P-I-N superlattice mid-infrared detector structure was realized. At 77 K the dark current density at −50 mV bias was 2.4 × 10⁻⁸ A/cm² and the resistance-area product (RA) at maximum (−50 mV bias) was 2.4 × 10⁶ Ω cm², and the peak detectivity was then calculated to be 9.0 × 10¹² cm Hz^1/2/W. The background limited infrared photodetector (BLIP) level can be achieved at a temperature of 113 K.     

Band engineered HOT midwave infrared detectors based on type-II InAs/GaSb strained layer superlattices

We report on heterostructure bandgap engineered midwave infrared photodetectors based on type-II InAs/GaSb strained layer superlattices with high operating temperatures. Bandgap and bandoffset tunability of antimonide based systems have been used to realize photodiodes and photoconductors. A unipolar barrier photodiode, pBiBn, and an interband cascade photovoltaic detector have been demonstrated with a 100% cutoff wavelength of 5 μm at 77 K. The pBiBn detector demonstrated operation up to room temperature and the cascade detector up to 420 K. A dark current density of 1.6 × 10⁻⁷ A/cm² and 3.6 × 10⁻⁷ A/cm⁻² was measured for the pBiBn and interband cascade detector, respectively, at 80 K. A responsivity of 1.3 A/W and 0.17 A/W was observed at −30 mV and −5 mV of applied bias for pBiBn and cascade detector, respectively, at 77 K. The experimental results have been explained by correlating them with the operation of the devices.     

Molecular Beam Epitaxy growth and characterization of silicon – Doped InAs dot in a well quantum dot infrared photo detector (DWELL-QDIP)

We report the growth by Molecular Beam Epitaxy (MBE), fabrication and characterization of silicon doped 20 layer InAs dot in a well quantum dot infrared photo detector (DWELL-QDIP) device structures. Two structures with InAs dots of vertical heights of 50 Å and 40 Å were compared. A 2–8 μm band normal incidence photo response of the detector with polarization and bias dependence was obtained at 77 K. The specific peak detectivity D1 be 0.8 × 10⁹ Jones for one of the detectors.     

Refinements of the WKMC empirical line lists (5852–7919 cm−1) for methane between 80 K and 296 K

During the last 4 years, empirical line lists for methane at room temperature and at 80 K were constructed from spectra recorded by (i) differential absorption spectroscopy (DAS) in the high energy part of the tetradecad (5852?6195 cm^?1) and in the icosad (6717–7589 cm^?1) and (ii) high sensitivity CW-Cavity Ring Down Spectroscopy (CRDS) in the 1.58 μm and 1.28 μm transparency windows (6165–6750 cm^?1 and 7541–7919 cm^?1, respectively). We have recently constructed the global line lists for methane in “natural” isotopic abundance, covering the spectral region from 5854 to 7919 cm^?1 (Campargue A, Wang L, Kassi S, Mondelain D, Bézard B, Lellouch E, et al., An empirical line list for methane in the 1.26–1.71 μm region for planetary investigations (T=80–300 K). Application to Titan, Icarus 219 (2012) 110–128). These WKMC (Wang, Kassi, Mondelain, Campargue) empirical lists include about 43,000 and 46,420 lines at 80±3 K and 296±3 K, respectively. The “two temperature method” provided lower state energy values, E_emp, for about 24,000 transitions allowing us to account satisfactorily for the temperature dependence of the methane absorption over the considered region. The obtained lists have been already successfully applied in a large range of temperature conditions existing on Titan, Uranus, Pluto, Saturn and Jupiter.In the present contribution, we provide some improvements to our lists by using literature data to extend the set of lower state energy values and by correcting the distortion of the high E_emp values (J>10) due to the temperature gradient existing in the cryogenic cell used for the recordings. The proposed refinements are found to have an overall limited impact but they may be significant in some spectral intervals below 6500 cm^?1.The new version of our lists at 80 K and 296 K is provided as Supplementary Material: the WKMC@80K+ and WKMC@296K lists are adapted for planetary and atmospheric applications, respectively. The WKMC@80K+ list is made applicable over a wider range of temperatures and shows satisfactory extrapolation capabilities up to room temperature. It was obtained by transferring to the 80 K list the 27,580 single lines present only in the 296 K list, with corresponding lower state energy values chosen to make them below the detectivity limit at 80 K.In the discussion, the different line lists and databases available for methane in the near infrared are compared and some suggestions are given.     

Mid-wave QWIPs for the [3–4.2 μm] atmospheric window

We report two approaches using Quantum Well Infrared Photodetectors for detection in the [3–4.2 μm] atmospheric window. Taking advantage of the large band gap discontinuity we demonstrated a strained AlInAs/InGaAs heterostructure on InP. The optical coupling in this structure has been experimentally and numerically investigated. The results show that the coupling is mainly due to guided modes. The second approach is based on double barrier strained AlGaAs/AlAs/GaAs/InGaAs active layers on GaAs. The segregation of the elements III in these structures has been investigated using a transmission electron microscope. The results show a strong modification of the conduction band profile. We demonstrate peak wavelengths at 3.9 μm for the InP based detector and 4.0 μm for the GaAs based detector. We report a background limited peak detectivity (2π field of view, 300 K background) at 4.0 μm of about 2 × 10¹¹ cm Hz^1/2 W^?1 at 77 K, and 1.5 × 10¹¹ cm Hz^1/2 W^?1 at 100 K.     

Analytical modeling and ATLAS simulation of N+-InP/n0-In0.53Ga0.47As/p+-In0.53Ga0.47As p-i-n photodetector for optical fiber communication

In this paper we report an analytical modeling of N⁺-InP/n⁰-In_0.53Ga_0.47As/p⁺-In_0.53Ga_0.47As p-i-n photodetector for optical fiber communication. The results obtained on the basis of our model have been compared and contrasted with the simulated results using ATLAS? and experimental results reported by others. The photodetector has been studied in respect of energy band diagram, electric field profile, doping profile, dark current, resistance area-product, quantum efficiency, spectral response, responsivity and detectivity by analytical method using closed form equations and also been simulated by using device simulation software ATLAS? from SILVACO® international. The photodetector exhibits a high quantum efficiency ～90%, responsivity ～1.152–1.2 A/W in the same order as reported experimentally by others, specific detectivity ～5 × 10⁹ cm Hz^1/2 W^?1at wavelength 1.55–1.65 μm, dark current of the order of 10^?11 A at reverse bias of 1.5 V and 10^?13–10^?12 A near zero bias. These values are comparable to those obtained for practical p-i-n detectors. The estimated noise equivalent power (NEP) is of the order of 2.5 × 10^?14 W.     

Quick response PZT/P(VDF-TrFE) composite film pyroelectric infrared sensor with patterned polyimide thermal isolation layer

The fabrication method and the pyroelectric response of a single element infrared sensor based lead zirconate titanate (PZT) particles and polyvinylidene fluoride P(VDF-TrFE) copolymer composite thick film is reported in this paper. A special thermal insulation structure, including polyimide (PI) thermal insulation layer and thermal insulation tanks, was used in this device. The thermal insulation tanks were fabricated by laser micro-etching technique. Voltage responsivity (R_V), noise voltage (V_noise), noise equivalent power (NEP), and detectivity (D^*) of the PZT/P(VDF-TrFE) based infrared sensor are 1.2 × 10³ V/W, 1.25 × 10⁻⁶ V Hz^1/2, 1.1 × 10⁻⁹ W and 1.9 × 10⁸ cm Hz^1/2 W⁻¹ at 137.3 Hz modulation frequency, respectively. The thermal time constant of the infrared sensor τ_T was about 15 ms. The results demonstrate that the composite infrared sensor show a high detectivity at high chopper frequency, which is an essential advantage in infrared detectors and some other devices.     

Mid-infrared photoconductive properties of heavily Bi-doped PbTe p–n homojunction diode grown by liquid-phase epitaxy

We fabricated a heavily Bi-doped (x_Bi ≈ 2 × 10¹⁹ cm⁻³) PbTe p–n homojunction diode that detects mid-infrared wavelengths by the temperature difference method (TDM) under controlled vapor pressure (CVP) liquid phase epitaxy (LPE). The photocurrent density produced by the heavily Bi-doped diode sample is approximately 20 times and 3 times greater than that produced by an undoped and heavily In-doped sample, respectively. By varying the ambient temperature from 15 K to 225 K, the detectable wavelength is tunable from 6.18 μm to 4.20 μm. The peak shift of the detectable wavelength is shorter in the heavily Bi-doped sample than in the undoped sample, consistent with our previously proposed model, in which Bi–Bi nearest donor–acceptor pairs are formed in the heavily Bi-doped PbTe liquid phase epitaxial layer. Current–voltage (I–V) measurements of the heavily Bi-doped diode sample under infrared exposure at 77 K indicated a likely leak in the dark current, arising from the deeper levels. From the dark I–V measurements, the activation energy of the deep level was estimated as 0.067 eV, close to the energy of the deep Tl-doped PbTe acceptor layer. We conclude that the deep level originates from the Tl-doped p-type epitaxial layer.     

Distinction investigation of InGaAs photodetectors cutoff at 2.9 μm

Using double heterojunction structure with linearly graded In_xAl_1–xAs as buffer layer and In_0.9Al_0.1As as cap layer, wavelength extended In_0.9Ga_0.1As detectors with cutoff wavelength of 2.88 μm at room temperature have been grown by using gas source molecular beam epitaxy, their characteristics have been investigated in detail and compared with the detectors cutoff at 2.4 μm with similar structure as well as commercial InAs detectors. Typical resistance area product R₀A of the detectors reaches 3.2 Ω cm² at 290 K. Measured peak detectivity reaches 6.6E9 cm Hz^1/2/W at room temperature.     

A proposed organic Schottky barrier photodetector for application in the visible region

The fabrication and characterization of an organic photodetector (OPD) in the form of ITO coated glass/polycarbazole (PCz)/Al Schottky contact is reported. The device has been fabricated in our laboratory for the first time using the polymer synthesized by us. The device has been subsequently characterized in respect of electrical and optical properties in order to explore its potential for possible use as a detector in the visible region at 650 nm. It is observed that the detector exhibits a reasonably high value of peak detectivity (∼6 × 10⁶ cm Hz^1/2 W⁻¹) near zero bias voltage at V = 0.2 V.