Production and characterization of oil-in-water emulsions containing droplets stabilized by multilayer membranes consisting of beta-lactoglobulin, iota-carrageenan and gelatin

The influence of environmental conditions (pH, NaCl, CaCl2, and temperature) on the properties and stability of oil-in-water (O/W) emulsions containing oil droplets surrounded by one-, two-, or three-layer interfacial membranes has been investigated. Three oil-in-water emulsions were prepared with the same droplet concentration and buffer (5 wt % corn oil, 5 mM phosphate buffer, pH 6) but with different biopolymers: (i) primary emulsion: 0.5 wt % beta-Lg; (ii) secondary emulsion: 0.5 wt % beta-Lg, 0.1 wt % iota-carrageenan; (iii) tertiary emulsion: 0.5 wt % beta-Lg, 0.1 wt % iota-carrageenan, 0-2 wt % gelatin. The secondary and tertiary emulsions were prepared by electrostatic deposition of the charged biopolymers onto the surfaces of the oil droplets so as to form two- and three-layer interfacial membranes, respectively. The stability of the emulsions to pH (3-8), sodium chloride (0-500 mM), calcium chloride (0-12 mM), and thermal processing (30-90 degrees C) was determined. We found that multilayer emulsions had better stability to droplet aggregation than single-layer emulsions under certain environmental conditions and that one or more of the biopolymer layers could be made to desorb from the droplet surfaces in response to specific environmental changes (e.g., high salt or high temperature). These results suggest that the interfacial engineering technology used in this study could lead to the creation of food emulsions with improved stability to environmental stresses or to emulsions with triggered release characteristics.     

Oxidative stability and effect of stress factors on flaxseed oil-in-water emulsions stabilized by sodium caseinate–sodium alginate–chitosan interfacial membrane

The susceptibility of heart healthy ω-3 fatty acids to lipid oxidation has hindered its incorporation into healthful foods and beverages. In this study, plant-based flaxseed oil rich in ω-3 fatty acids were dispersed into primary, secondary and tertiary emulsion system. A primary emulsion containing sodium caseinate-stabilized cationic droplets was prepared by homogenizing flaxseed oil as oil phase and sodium caseinate solution as the aqueous phase in an ultrasonicator. A secondary emulsion comprising of sodium caseinate–sodium alginate anionic droplets were produced by diluting appropriate primary emulsion with alginate solution. Further, a tertiary emulsion composed of sodium caseinate–sodium alginate–chitosan-coated cationic droplets was produced by diluting secondary emulsion with chitosan solution. The resistance of primary, secondary and tertiary emulsions with the same lipid concentration to destabilization by thermal treatment (30–90 °C for 30 min), sodium chloride addition (≤70 mM NaCl) and oxidative degradation (hydroperoxide concentration and TBARS) was determined. The results showed that secondary emulsions could resist variation in environmental stresses of salt and heat as well as protect the oil phase from decomposition better than primary and tertiary emulsions. Interfacial engineering could be used to design emulsion system with desirable characteristics.     

Influence of environmental stresses on stability of oil-in-water emulsions containing droplets stabilized by beta-lactoglobulin-iota-carrageenan membranes

An oil-in-water emulsion (5 wt% corn oil, 0.5 wt% beta-lactoglobulin (beta-Lg), 0.1 wt% iota-carrageenan, 5 mM phosphate buffer, pH 6.0) containing anionic droplets stabilized by interfacial membranes comprising of beta-lactoglobulin and iota-carrageenan was produced using a two-stage process. A primary emulsion containing anionic beta-Lg coated droplets was prepared by homogenizing oil and emulsifier solution together using a high-pressure valve homogenizer. A secondary emulsion containing beta-Lg-iota-carrageenan coated droplets was formed by mixing the primary emulsion with an aqueous iota-carrageenan solution. The stability of primary and secondary emulsions to sodium chloride (0-500 mM), calcium chloride (0-12 mM), and thermal processing (30-90 degrees C) were analyzed using zeta-potential, particle size and creaming stability measurements. The secondary emulsion had better stability to droplet aggregation than the primary emulsion at NaCl 相似文献   

Impact on Morphological Characterization and Emulsion Stability of Lactoferrin–Beet Pectin Electrostatic Complexes

Interfacial protein–polysaccharide complexes can be utilized in emulsion-based delivery system and contained functional component or medical ingredient. In the present work, the interaction of lactoferrin (LF, 0.2 wt%) with beet pectin (BP, 0–0.15 wt%) was researched in aqueous solutions at different pH (2–9) and ionic strength (0–800 mM) to provide the information about properties of complexes. A simulative environment was created to explore the optimal concentration of BP to formulate LF-coated stabilized emulsion and how the emulsion responded to the changing environmental pH (2–9) and ionic strength (0–500 mM). Particle size, particle distribution index, zeta-potential, turbidity, Turbiscan stability index,, and peak thickness were used to characterize the physical stability of emulsions. The confocal laser scanning microscopy was used to derive the microscopy images of droplets. The results indicated that 0.4 wt% was the optimal concentration to formulate emulsions, and the LF-BP-coated bilayer emulsion has a preferable stability in more extensive range than the pure LF-stabilized emulsions under the environmental stresses through electrostatic interactions. The results of this study will play an important role in facilitating the utilization of LF-BP complexes as an emulsifier in the development of incorporating functional component or medical ingredient into commercial products.     

Influence of Interfacial Rheological Properties on Stability of Asphaltene-Stabilized Emulsions

A series of oscillating droplet measurements have been performed on asphaltenes at the oil/water interface, in order to correlate the interfacial rheological behavior to their ability to stabilize emulsions. In the concentration sweep, the elastic modulus goes through a maximum around an asphaltene concentration of 0.05–0.10 g/l. This behavior was not in good correspondence with emulsion stability, which increased consistently from low to high concentrations. The decrease above 0.10 g/l was most likely an effect of diffusion of asphaltenes in the bulk to the interface, which became more significant at higher bulk concentrations. The rheology data as a function of concentration has been fitted to Butler's surface equation of state and the Lucassen–van den Tempel model. A decent correlation was found between emulsion stability and elasticity for both the effect of solvent aromaticity and pH. The elastic modulus displayed a gradual increase when xylene was mixed with heptane as the solvent, as was seen with emulsion stability. This was not caused by a significant increase of the adsorbed amount of asphaltene at the interface, as shown by a quartz crystal microbalance (QCM), but a more efficient reorganization of the already adsorbed asphaltenes. The ability asphaltenes displayed in stabilizing emulsions was significantly increased at both low and high pH, according to a previous study. The elastic modulus, on the other hand, only showed a very weak increase at pH 2, but a better correlation with emulsion stability above pH 8. From this it would appear that the dissociation of acid groups in the asphaltene structure at high pH has a bigger impact on the interfacial activity than the protonation of bases at low pH, while their effect on emulsion stability was the same.      

Comparison of droplet flocculation in hexadecane oil-in-water emulsions stabilized by beta-lactoglobulin at pH 3 and 7

The influence of surface and thermal denaturation of adsorbed beta-lactoglobulin (beta-Lg) on the flocculation of hydrocarbon oil droplets was measured at pH 3 and compared with that at pH 7. Oil-in-water emulsions (5 wt % n-hexadecane, 0.5 wt % beta-Lg, pH 3.0) were prepared that contained different levels of salt (0-150 mM NaCl) added immediately after homogenization. The mean particle diameter (d43) and particle size distribution of diluted emulsions were measured by laser diffraction when they were either (i) stored at 30 degrees C for 48 h or (ii) subjected to different thermal treatments (30-95 degrees C for 20 min). In the absence of salt, little droplet flocculation was observed at pH 3 or 7 because of the strong electrostatic repulsion between the droplets. In the presence of 150 mM NaCl, a progressive increase in mean particle size with time was observed in pH 7 emulsions during storage at 30 degrees C, but no significant change in mean particle diameter with time (d43 approximately 1.4 +/- 0.2 microm) was observed in the pH 3 emulsions. Droplet aggregation became more extensive in pH 7 emulsions containing salt (added before thermal processing) when they were heated above 70 degrees C, which was attributed to thermal denaturation of adsorbed beta-Lg leading to interdroplet disulfide bond formation. In contrast, the mean particle size decreased and the creaming stability improved when pH 3 emulsions were heated above 70 degrees C. These results suggest that the droplets in the pH 3 emulsions were weakly flocculated at temperatures below the thermal denaturation temperature of beta-Lg (T < 70 degrees C) but that flocs did not form so readily above this temperature, which was attributed to a reduction in droplet surface hydrophobicity due to protein conformational changes. The most likely explanation for the difference in behavior of the emulsions is that disulfide bond formation occurs much more readily at pH 7 than at pH 3.     

Effect of Nanoparticle Hydrophobicity on Stability of Highly Concentrated Emulsions

The effect of hydrophobicity index (HI) of fumed nanosilica specimens on stability of water-in-oil (W/O) highly concentrated emulsions (HCE with ? = 90 vol%) with an overcooled dispersed phase was studied. A series of five silica with HI in the 0.60–1.34 range and HI > 3 were used separately and in combination with a low molecular weight traditional surfactant, Sorbitan MonoOleate (SMO). First, it was shown that SMO alone can stabilize W/O HCE whereas only silica nanoparticles with intermediate HI in the range 0.97 ≤ HI ≤ 1.34 could form W/O emulsions only up to 77–79 vol%. Then, on the contrary to SMO-based emulsions, Pickering emulsions are unstable under shearing. When mixed (silica plus SMO) emulsifier systems were used, firstly a thermodynamic consideration revealed that only SMO is likely to adsorb at the W/O interface and controls the emulsifying process by the decrease in the interfacial tension. Then, interestingly, all different kinds of emulsion stability investigated in this study demonstrate a breaking point (BP) at HI = 0.97. Below the BP the emulsions were found to be very unstable on shelf as well as under shear. Above the BP, a clear synergy between colloidal silica and SMO surfactant has been found.      

Effect of dispersion pH on the formation and stability of Pickering emulsions stabilized by layered double hydroxides particles

Using positively charged plate-like layered double hydroxides (LDHs) particles as emulsifier, liquid paraffin-in-water emulsions stabilized solely by such particles are successfully prepared. The effects of the pH of LDHs aqueous dispersions on the formation and stability of the emulsions are investigated here. The properties of the LDHs dispersions at different pHs are described, including particle zeta potential, particle aggregation, particle contact angle, flow behavior of the dispersions and particle adsorption at a planar oil/water interface. The zeta potential decreases with increasing pH, leading to the aggregation of LDHs particles into large flocs. The structural strength of LDHs dispersions is enhanced by increasing pH and particle concentration. The three-phase contact angle of LDHs also increases with increasing pH, but the variation is very small. Visual observation and SEM images of the interfacial particle layers show that the adsorption behavior of LDHs particles at the planar oil/water interface is controlled by dispersion pH. We consider that the particle-particle (at the interface) and particle-interface electrostatic interactions are well controlled by adjusting the dispersion pH, leading to pH-tailored colloid adsorption. The formation of an adsorbed particle layer around the oil drops is crucial for the formation and stability of the emulsions. Emulsion stability improves with increasing pH and particle concentration because more particles are available to be adsorbed at the oil/water interface. The structural strength of LDHs dispersions and the gel-like structure of emulsions also influence the stability of the emulsions, but they are not necessary for the formation of emulsions. The emulsions cannot be demulsified by adjusting emulsion pH due to the irreversible adsorption of LDHs particles at the oil/water interface. TEM images of the emulsion drops show that a thick particle layer forms around the oil drops, confirming that Pickering emulsions are stabilized by the adsorbed particle layers. The thick adsorbed particle layer may be composed of a stable inner particle layer which is in direct contact with the oil phase and a relatively unstable outer particle layer surrounding the inner layer.     

Factors affecting the stability of O/W emulsion in BSA solution: stabilization by electrically neutral protein at high ionic strength

Bovine serum albumin (BSA) was used as an emulsifier to disperse corn oil in aqueous media with various protein concentration, pH, and ionic strength. Quantitative estimation was made on the homogenizing activity of BSA and dispersion stability of oil particles by measuring particle size, turbidity, and creaming rate. Dispersion stability strongly depended on pH and became a minimum around pH 5.0 which was the isoelectric point of BSA. The interfacial tension between BSA solution and corn oil was minimized at pH 5.0. Interesting results were obtained concerning the ionic-strength dependence of stability. When the ionic strength was set below 30 mM, the emulsions became more stable with the increase of BSA concentration at pH 6.7 but the opposite behavior (enhanced destabilization) was confirmed at pH 5.0 with the BSA content. In high ionic strength conditions (ca. > or = 80 mM NaCl), however, BSA-stabilized emulsions became fairly stable even at pH 5.0. These results suggested that BSA molecules having no net charge induced some attractive interactions (e.g., bridging or depletion) in low ionic strength but steric stabilization in high ionic strength, respectively.     

The Effect of Oil Components and Homogenization Conditions on the Physicochemical Properties of Zedoary Turmeric Oil Submicron Emulsions

Zedoary turmeric oil submicron emulsions were studied. The effects of the oil phase as a mixture (ternary) on the emulsion droplet size were investigated by means of the simplex lattice design. By optimizing the homogenization process and using only 1.2% soya lecithin, emulsions with 20% oil phase consisting of zedoary turmeric oil–MCT–soybean oil ratio of 0.5:0.25:0.25 with particle sizes in the range of 132–148 nm and moderate viscosity (3.6–4.0 mPa · s) could be prepared. These emulsions showed good stability over 6 months. This study showed the dominating influence of composition of the oil phase as well as the importance of the homogenizing conditions on processing and stability of the zedoary turmeric oil submicron emulsions.     

Effects of emulsifier type and environmental stress on the stability of curcumin emulsion

The objective of this study was to investigate the effects of environmental stress and emulsifier types on the stability of curcumin emulsions. Results showed that Lecithin and Tween 80 presented good emulsifying capacity. The Tween 80 emulsion was the most stable among the four emulsions.

The particle sizes of Tween 80 and whey protein emulsion were relatively smaller than gum arabic and lecithin. Extensive droplet aggregation appeared in whey protein-stabilized emulsions when the pH was approximately isoelectric point (pI) with salt concentration >200?mM. Lecithin emulsion was unstable when pH?≤?6 with salt concentration >100?mM. There was little impact of pH and ionic strength on gum arabic and Tween 80 emulsions. All of the emulsions were stable at temperatures from 30 to 90°C in the absence of salt. These results help characterize the emulsifying and stabilizing abilities of emulsifier types intended for applications in the food industry.     

Flaxseed Oil-In-Water Emulsions Stabilized by Multilayer Membranes: Oxidative Stability and the Effects of pH

The investigation of the effect of multilayer membranes on the stability of flaxseed oil-in-water (o/w) emulsions was the main goal of this study. The primary emulsion was prepared by homogenizing the oil phase (10 wt%) with an aqueous sodium caseinate solution (90 wt% and a pH 6.8) using a high-pressure microfluidizer. This emulsion was mixed with a pectin solution to form a secondary emulsion at a pH 6.8 and then adjusted to a pH to 3 for the adsorption of anionic pectin molecules on the surface of the cationic droplet surfaces. The pH effect on the physical stability of the emulsions was evaluated by measuring the mean particle diameter, ζ-potential, creaming index, and visualization of the microstructure. Also, the oxidative stability was determined by monitoring the lipid hydroperoxides and thiobarbituric acid-reactive substances (TBARs) at 55°C. The results of this study indicate that a multilayer structure had a positive effect on the improvement of the physical and oxidative stability of the conventional emulsions under certain pH conditions and limited storage period.     

Hofmeister Salts Affect Buildup of Thin Multilayer Films Surrounding Oil Droplets

The layer-by-layer electrostatic deposition method is a novel technique to precisely control the interfacial properties of multilayered films such as charge, thickness, permeability, and composition. The formation and stability of multilayered emulsions is however often plagued by extensive droplet flocculation and aggregation even at ideal polyelectrolyte concentrations where saturation should occur. Addition of salts may reduce the degree of attractive interactions ions and thus improve deposition. To test this hypothesis, the influence of different Hofmeister salts (KCl, NaCl, LiCl, and NH₄Cl) at various salt concentrations (0–2500 mM) on the aggregation behavior of multilayered emulsions was investigated. A simple coating process of fish gelatin interfacial membranes with sugar beet pectin was used. Our results show that mean particle diameter and particle size distribution of emulsions initially decreased from 600 nm to 328 nm with increasing salt concentrations up to 250 mM. Above a critical level (>500 mM), heavy aggregation of emulsions at the presence of chaotropic salts occurred whereas kosmotropes reduced flocculation and creaming. Microscopic images and isothermal titration calorimetry confirmed particle size measurements. Results thus suggest that addition of salts may be an extremely useful tool to modulate and improve depositioning of alternatingly charged polymers on surfaces.      

Double inversion of emulsions induced by salt concentration

The effects of salt on emulsions containing sorbitan oleate (Span 80) and Laponite particles were investigated. Surprisingly, a novel double phase inversion was induced by simply changing the salt concentration. At fixed concentration of Laponite particles in the aqueous phase and surfactant in paraffin oil, emulsions are oil in water (o/w) when the concentration of NaCl is lower than 5 mM. Emulsions of water in oil (w/o) are obtained when the NaCl concentration is between 5 and 20 mM. Then the emulsions invert to o/w when the salt concentration is higher than 50 mM. In this process, different emulsifiers dominate the composition of the interfacial layer, and the emulsion type is correspondingly controlled. When the salt concentration is low in the aqueous dispersion of Laponite, the particles are discrete and can move to the interface freely. Therefore, the emulsions are stabilized by particles and surfactant, and the type is o/w as particles are in domination. At intermediate salt concentrations, the aqueous dispersions of Laponite are gel-like, the viscosity is high, and the transition of the particles from the aqueous phase to the interface is inhibited. The emulsions are stabilized mainly by lipophilic surfactant, and w/o emulsions are obtained. For high salt concentration, flocculation occurs and the viscosity of the dispersion is reduced; thus, the adsorption of particles is promoted and the type of emulsions inverts to o/w. Laser-induced fluorescent confocal micrographs and cryo transmission electron microscopy clearly confirm the adsorption of Laponite particles on the surface of o/w emulsion droplets, whereas the accumulation of particles at the w/o emulsion droplet surfaces was not observed. This mechanism is also supported by the results of rheology and interfacial tension measurements.     

Influence of pH on the stability of oil-in-water emulsions stabilized by a splittable surfactant

A laboratory study was conducted to evaluate the effect of pH on the stability of oil-in-water emulsions stabilized by a commercial splittable surfactant Triton SP-190 by comparison with the results obtained by a common surfactant Triton X-100. The emulsion stability was explored by measuring the volume of oil phase separated and the size of the dispersed droplets. It was found that the addition of inorganic acids did not significantly affect the stability of emulsions stabilized by Triton X-100, but had a profound influence on the stability of emulsions stabilized by Triton SP-190. Moreover, the droplet size of a Triton X-100-stabilized emulsion and its dynamic interfacial activity were insensitive to acids. However, at lower pH the droplet size of the emulsions stabilized by Triton SP-190 was considerably increased. From the dynamic interfacial tension measurements the dynamic interfacial activity of Triton SP-190 at the oil/water interface was found to be strongly inhibited by the addition of acids, resulting in a slower decreasing rate of dynamic interfacial tension. The results demonstrate that the dramatic destabilization of Triton SP-190-stabilized emulsions could be realized by the use of acids, which evidently changed the interfacial properties of the surfactant and resulted in a higher coalescence rate of oil droplets.     

Complex formation in mixtures of lysozyme-stabilized emulsions and human saliva

In this paper, we studied the interaction between human unstimulated saliva and lysozyme-stabilized oil-in-water emulsions (10 wt/wt% oil phase, 10 mM NaCl, pH 6.7), to reveal the driving force for flocculation of these emulsions. Confocal scanning laser microscopy (CSLM) showed formation of complexes between salivary proteins and lysozyme adsorbed at the oil-water interface and lysozyme in solution as well. To assess the electrostatic nature of the interaction in emulsion/saliva mixtures, laser-diffraction and rheological measurements were conducted in function of the ionic strength by adding NaCl to the mixture in the range between 0 and 168 mM. Increasing the ionic strength reduced the ability of saliva to induce emulsion flocculation as shown by the decreased floc size and the effect on the viscosity. Turbidity experiments with varying pH (3-7) and ionic strength also showed decreased complex formation in mixtures between saliva and lysozyme in solution upon NaCl addition up to 200 mM. Decreasing the pH increased the turbidity, in line with the increase of the positive net charge on the lysozyme molecule. We conclude that electrostatic attraction is the main driving force for complex formation between saliva components and lysozyme adsorbed at the oil droplets and in solution.     

Effect of Interfacially Active Fractions of Some Egyptian Crude Oils on Their Emulsion Stability

Four samples from different crude oils were used for this study: light and heavy crude oils from Iran and two crude oils from Egypt, namely, Ras Gharb and Suez mix. The asphaltenes were separated from these crude oils and then the maltene (non‐asphaltenic fraction) was fractionated into waxes, aromatics, and resins. All fractions were characterized using FTIR and UV spectroscopic analyses in addition to gel permeation chromatograph (GPC). These fractions were tested for their emulsion stability. For chemometric analysis different parameters (variables) have been used to study the effect of different fractions (objects) on the emulsion stability. Such variables included the integrated areas under the stretching absorption peaks of CH in the range of 3000–2800 cm^?1, C?O in the range of 1750–1650 cm^?1, and the aromatic C?C in the range of 1650–1550 cm^?1, as well as UV absorption value at 235 nm and average molecular weight (MW). Principal component analysis (PCA) and multiple linear regression (MLR) were conducted for examining the relationship between multiple variables and the stability of water‐in‐crude oil emulsions. The results of PCA explain the interrelationships between the observations and variables in multivariate data. The correlation coefficients between different parameters derived from PCA reveals that the UV absorption value and MW are strongly correlated with emulsion stability. It also reveals that the resins, asphaltenes, and maltene have better emulsion stability than waxes and lower molecular weight aromatics. The linear relationship between the parameters and the stability of water‐in‐crude oil emulsions using MLR was modeled according to the better statistical results. The obtained mathematical model can be used to predict the stability of water‐in‐crude oil emulsions from the chemical groups and functionalities in each crude oil fraction.     

Oil-in-water emulsions stabilized by whey protein aggregates: Effect of aggregate size,pH of aggregation and emulsion pH

Oil-in-water emulsions (60% oil (w/w)) were prepared using whey protein aggregates as the sole emulsifying agent. The effects of whey protein aggregate size (the diameter between 0.92 and 10.9?µm), the pH of emulsions (4–8.6) and storage time on physical properties, droplet size, and stability of emulsions were investigated. The results indicate that increment of whey protein aggregate size caused an increase in the firmness, droplet size, and viscosity of emulsions, and also a decrease in the emulsion creaming. The emulsion viscosity, firmness, and droplet size were reduced by increasing the emulsion pH; however, the creaming process was accelerated. Viscosity, creaming, and droplet size of emulsions were increased slightly during 21 days storage at 40°C.     

Effect of the type of the oil phase on stability of highly concentrated water-in-oil emulsions

The water-in-oil high internal phase emulsions were the subject of the study. The emulsions consisted of a super-cooled aqueous solution of inorganic salt as a dispersed phase and industrial grade oil as a continuous phase. The influence of the industrial grade oil type on a water-in-oil high internal phase emulsion stability was investigated. The stability of emulsions was considered in terms of the crystallization of the dispersed phase droplets (that are super-cooled aqueous salt solution) during ageing. The oils were divided into groups: one that highlighted the effect of oil/aqueous phase interfacial tension and another that investigated the effect of oil viscosity on the emulsion rheological properties and shelf-life. For a given set of experimental conditions the influence of oil viscosity for the emulsion stability as well as the oil/aqueous interfacial tension plays an important role. Within the frames of our experiment it was found that there are oil types characterized by optimal parameters: oil/aqueous phase interfacial tension being in the region of 19–24 mN/m and viscosity close to 3 mPa s; such oils produced the most stable high internal phase emulsions. It was assumed that the oil with optimal parameters kept the critical micelle concentration and surfactant diffusion rate at optimal levels allowing the formation of a strong emulsifier layer at the interface and at the same time creating enough emulsifier micelles in the inter-droplet layer to prevent the droplet crystallization.     

Effect of electrolyte in silicone oil-in-water emulsions stabilised by fumed silica particles

Partially hydrophobised fumed silica particles are used to make silicone oil-in-water emulsions at natural pH of the aqueous phase. The stability and rheological properties of the emulsions and suspensions are studied at NaCl concentrations in the range 0-100 mM. It is found that all emulsions are very stable to coalescence irrespective of the NaCl concentration. However, a strong effect of electrolyte on the creaming and rheological properties is observed and linked to the particle interactions in aqueous suspensions. The creaming rate and extent are large at low electrolyte concentrations but both abruptly decrease at salt concentrations exceeding the critical flocculation concentration of the suspension (approximately 1 mM NaCl). The drastic improvement of the stability to creaming is attributed to the formation of a visco-elastic three-dimensional network of interconnected particles and emulsion droplets.