非标记凝血酶阵列电化学适体传感器的研究

基于自制的集成化三阵列金膜电极,构建了一个简单、灵敏、非标记的凝血酶阵列电化学适体传感器。以聚乙烯不干胶掩膜版法结合金属溅射沉积技术,在FR-4玻璃纤维板上制作了由3个金膜工作电极、1个大面积金膜对电极和1个厚膜Ag/AgCl参比电极构成的集成化金膜阵列电极系统。以集成化金膜阵列电极作为基础电极,采用巯基自组装技术将带巯基的凝血酶适体固定在3个金工作电极表面,巯基己醇封闭后获得三阵列凝血酶适体传感器,以电活性物质铁氰化钾作为电化学探针,基于凝血酶适体和凝血酶结合前后铁氰化钾在电极表面传质的不同导致电流变化进行凝血酶的测定。采用方波脉冲伏安法,铁氰化钾氧化峰电流的变化值与凝血酶浓度在1.52~63 nmol/L范围内呈良好的线性关系,检出限(S/N=3)为0.92 nmol/L。     

基于共面薄膜金电极的三磷酸腺苷适体传感器

为了检测三磷酸腺苷(ATP)的浓度,利用微系统(MEMS)技术小批量加工薄膜金电极,采用自组装法将巯基修饰的三磷酸腺苷适体固定到金电极表面,以三磷酸腺苷适体作为识别元件,构建了一种基于共面薄膜金电极的三磷酸腺苷适体传感器。依据核酸磷酸骨架荷负电特性静电排斥[Fe(CN)6]3!/4!所引起的阻抗变化实现对ATP浓度的检测。首先采用电化学阻抗谱法研究了裸金电极及ATP加入前后、6-巯基己醇封闭电极前后以及不同自组装时间(3,8,15,24和30 h)条件下,电极在电化学阻抗溶液中阻抗值变化。然后研究了不同浓度ATP适体传感器的电化学阻抗谱以及适体传感器的线性度和重复性。结果表明,在自组装时间为24 h,使用6-巯基己醇封闭金电极的条件下,此传感器线性测量范围可达到1~500 nmol/L,检出限为1 nmol/L,线性相关系数为0.9842。此传感器制作简单,检出限低且重复性好。     

集成化金膜阵列电极的制作研究

以聚乙烯不干胶掩膜版法结合金属溅射沉积技术在FR-4玻璃纤维版上制作了由6个金膜工作电极(1 mm×2 mm)、1个大面积金膜对电极(2 mm×13 mm)和1个厚膜Ag/AgCl参比电极构成的集成化金膜阵列电极系统,并利用电化学手段对阵列电极系统进行了考察。研究结果表明,K3Fe(CN)6在厚膜Ag/AgCl/1.0 mol/L NaCl参比电极上的式电位与商业Ag/AgCl/3.0 mol/L NaCl参比电极相差0.067 V;参比电极放置1个月后,测量电位未发生明显变化。利用扫描电化学显微镜对工作电极表面平整度进行考察,结果表明工作电极表面具有较好的平整度。通过测量H2SO4还原峰面积评价了工作电极电化学面积的批内、批间一致性;通过K3Fe(CN)6在电极上的Ipa/Ipc比值评价了工作电极电化学特性的批内、批间一致性。结果表明,阵列电极面积和电化学特性具有良好的批内和批间一致性。对集成化金膜阵列电极系统的研究结果表明,聚乙烯不干胶掩膜版法结合金属溅射沉积技术制作的阵列电极能够满足电化学电极的要求,可作为电化学生物传感器的基础电极。     

基于单壁碳纳米管和目标诱导适体转移电化学适体传感器检测腺苷

以修饰于电极表面的单壁碳纳米管(SWNTs)作为适体固定平台,基于目标诱导适体(Aptamer)转移,构建了检测腺苷的电化学适体传感器。将SWNTs修饰到玻碳电极表面,没有目标物腺苷时,亚甲基蓝标记的腺苷适体(MB-Aptamer)通过适体与SWNTs之间强的相互作用固定在电极表面,此时电极表面因为有大量MB存在,能够检测到强的MB氧化电流信号。当引入腺苷后,因为腺苷与适体的相互作用力大于适体与SWNTs的相互作用力,迫使MB-Aptamer脱离电极进入溶液,此时电极表面MB量减少,导致MB氧化电流强度减弱,根据加入腺苷前后传感器表面MB氧化电流强度的变化,采用方波脉冲伏安法对腺苷进行检测。结果表明,MB氧化电流信号比值与腺苷浓度在0.0010~0.50 nmol/L之间呈良好的线性关系,检出限为0.49 pmol/L(S/N=3)。     

基于多边形金纳米颗粒的非标记型可卡因适体传感器的研制

实验合成了多边形金纳米颗粒,通过壳聚糖(CHIT)将合成的多边形金纳米颗粒固定在玻碳电极表面,然后通过自组装技术将带巯基的捕获DNA探针固定在修饰有多边形金纳米颗粒的电极表面,利用杂交反应使可卡因适体与DNA捕获探针结合,制成非标记型可卡因适体传感器。以六氨合钌作为电化学指示剂,通过测量传感器与目标物可卡因结合前后电流变化情况对可卡因进行测定。考察了缓冲溶液的pH、可卡因培育时间、扫描速度等对测定的影响。结果表明,在pH为7.40时该传感器的检测范围为1.0×10-10～1.0×10-3 mol/L,检测限为3.0×10-11 mol/L。该传感器制作简单,响应好,抗干扰能力强。     

非标记夹心式电化学可卡因适体传感器的研究

设计一种基于双链核酸适体的非标记夹心式电化学适体传感器, 建立简单、高灵敏度的可卡因分析方法. 首先将末端巯基修饰的捕获适体探针组装在金电极表面, 构建可卡因适体传感器. 该传感器与目标分子可卡因和部分互补的检测适体探针作用后, 在电极表面形成适体/可卡因/适体复合物. 以六氨合钌为信号分子, 基于单链适体和适体/可卡因/适体复合物对六氨合钌吸附量的不同, 通过计时电量法检测电极表面吸附六氨合钌的还原电量, 进行可卡因的分析检测. 在优化的条件下, 还原电量与可卡因浓度在1～50 mmol/L范围内呈良好的线性关系, 检出限为0.1 mmol/L. 用于血清中可卡因的检测, 回收率为96.4%～104%. 该方法简单, 灵敏度高, 可作为一种通用型的适体传感器模型.     

基于Pd-Au纳米颗粒的非标记型凝血酶传感器的研制

采用电沉积方法将Pd纳米颗粒沉积到玻碳电极(GCE)表面,再将Pd纳米颗粒修饰电极插入H2SO4溶液中,吸收适量活性氢后,转移到HAuCl4溶液中,静置一定时间后,使金被活性氢还原并自发沉积到Pd纳米颗粒修饰的玻碳电极表面。通过自组装作用将带巯基的凝血酶适配体Ⅰ固定在Pd-Au/GCE表面,制得非标记型凝血酶适配体传感器。当凝血酶与凝血酶适配体结合时,覆盖在电极表面,从而阻碍了电极表面的Pd-Au纳米颗粒对H2O2的催化还原活性,通过监测H2O2还原电流的减小程度,实现对凝血酶的定量检测。考察了pH值、培育时间等实验条件对响应电流的影响以及Pd-Au纳米颗粒的协同作用。实验表明,此传感器的线性范围为3.0~300 nmol/L,检出限为0.98 nmol/L。     

基于不同电化学探针检测乳腺癌基因片段电化学传感器的研究

构建了以3种不同电活性物质(铁氰化钾平衡电对、亚甲基蓝和六氨合钌)为电化学信号探针,检测乳腺癌基因片段(乳腺癌DNA)的电化学传感器。利用吸附作用将探针ss DNA固定于金纳米-多壁碳纳米管-Nafion复合纳米材料修饰金电极表面,制备了DNA电化学传感器。采用循环伏安法、电化学阻抗法和微分脉冲伏安法,对DNA电化学传感器进行表征和定量分析。实验结果表明,在5 mmol/L K3[Fe(CN)6]-5mmol/L K4[Fe(CN)6]平衡电对电化学探针检测液中,乳腺癌DNA的线性范围为0.1~500.0 nmol/L,其检出限(S/N=3)为0.03 nmol/L。以20μmol/L亚甲基蓝为电化学探针检测液时,乳腺癌DNA的线性范围为1.0~500.0 nmol/L,检出限为0.3 nmol/L。利用50μmol/L六氨合钌电化学探针检测时,乳腺癌DNA的线性范围为1.0~500.0 nmol/L,检出限为0.3 nmol/L。3种电化学探针中,利用铁氰化钾平衡电对探针检测乳腺癌DNA的检出限最低,线性范围最宽。该传感器可用于其他DNA的检测分析。     

基于石墨烯化学修饰电极的适体传感器

采用石墨烯(RGO)作载体,凝血酶适体(TBA)作探针,凝血酶为目标蛋白,电化学阻抗谱(EIS)为检测技术,建立了检测蛋白质的新方法。由于RGO可增大电极有效表面积并提高电极表面电子传输速率以及TBA的特异性识别能力,此方法具有较高的灵敏度和良好的选择性。采用本方法检测凝血酶的线性范围为0.3～10 fmol/L,检出限为0.26 fmol/L。本研究将RGO应用于电化学适体传感器,证实了RGO修饰电极在电化学适体传感器领域中潜在的应用价值。     

一种胶质瘤细胞的核酸适体电化学阻抗传感器

本文基于交流阻抗谱技术发展了一种新型的高灵敏核酸适体传感器用于胶质瘤细胞的检测。该传感器通过巯基在金表面的混合自组装,将腱肽蛋白c的核酸适体探针固定于金电极表面。基于腱肽蛋白在胶质瘤细胞表面的高表达,利用细胞与电极表面核酸适体探针的特异性生物识别对铁氰化物电化学阻抗的抑制,建立了胶质瘤细胞检测的核酸适体传感器。考察并优化了核酸适体/巯基丙酸混合自组装比例、反应时间、温度和离子强度等对传感器性能有显著影响的分析条件,结果表明该传感器的阻抗响应与胶质瘤细胞浓度呈线性关系,线性范围为100~50 000 cell/mL,其检出限可达50 cell/mL。     

亚微米级叉指型超微带电极阵列的加工和电化学表征

超微电极具有常规电极无法比拟的优良的电化学特性.超微电极包括单超微电极和超微电极阵列,单超微电极响应电流较小,一般仪器难以检测;而超微电极阵列除具有单超微电极的特点外,还能增加测量时的响应电流,有利于仪器检测.其中的叉指型超微带电极阵列(IDA)具有产生-收集效应,可提高检测的灵敏度,实现低浓度测量[1～4].将微电子技术和微细加工技术应用于化学和生物传感技术已引起关注,利用微细加工技术可以实现传感器的微型化、集成化和智能化;减少测量使用的样品量;使传感器的敏感元件具有确定的形状和尺寸,提高测量结果的一致性.本文用多…     

Label‐Free Electrochemical Aptasensor for Determination of Chloramphenicol Based on Gold Nanocubes‐Modified Screen‐Printed Gold Electrode

An ultrasensitive label‐free electrochemical aptasensor was developed for selective detection of chloramphenicol (CAP). The aptasensor was made using screen‐printed gold electrode modified with synthesized gold nanocube/cysteine. The interactions of CAP with aptamer were studied by cyclic voltammetry, square wave voltammetry (SWV) and electrochemical impedance spectroscopy. Under optimized conditions, two linear calibration curves were obtained for CAP determination using SWV technique, from 0.03 to 0.10 µM and 0.25–6.0 µM with a detection limit of 4.0 nM. The aptasensor has the advantages of good selectivity and stability and applied to the determination of CAP in human blood serum sample.     

Aptamer-based highly sensitive electrochemical detection of thrombin via the amplification of graphene

Herein, we successfully fabricated a highly sensitive label-free electrochemical aptasensor for thrombin based on the amplification of graphene (Gra). The excellent electrochemical probe of nickel hexacyanoferrate nanoparticles (NiHCFNPs) was introduced to form Nafion-Graphene-NiHCFNPs (Nf-Gra-NiHCFNPs) nanocomposites membrane on the gold electrode. The employment of graphene not only enhanced the surface area of the electrode with increased NiHCFNPs immobilization, but also improved the conductivity of the electrode, which further effectively improved the sensitivity of this proposed aptasensor. Subsequently, AuNPs layer was formed to immobilize the thrombin aptamer (TBA) and enhance the stability of the composite monolayer mentioned above. Then, thiol-modified TBA was assembled onto the AuNPs layer. Thereafter, hexanethiol (HT) was employed to block the possible remaining active sites. With the dual amplification of Gra and AuNPs, the resulting aptasensor exhibited good current response to target thrombin with a wide linear range extended from 1 pM to 80 nM (the detection limit was 0.3 pM). Additionally, the morphologies of bare Au substrate, nickel hexacyanoferrate nanoparticles (NiHCFNPs) and nanocomposites were successfully characterized by atomic force microscopy (AFM).     

基于微带阵列电极的微型葡萄糖传感器研究

用微电子薄膜技术制作了微带阵列电极（ＭＡＥ）,考察了该电极在铁氰化钾,过氧化氢溶液中的电化学行为。在微带阵列电极表面,修饰一层全氟代磺酸酯膜作为基底电极,并把电子介体二茂铁及葡萄糖氧化酶固定在基底电极上制备了微型葡萄糖传感器,探讨了微酶电极对葡萄糖氧化过程的催化作用。该微酶电极响应时间小于１０ｓ,检测线性上限为８ｍｍｏｌ／Ｌ。     

Blocking properties of gold electrodes modified with 4-nitrophenyl and 4-decylphenyl groups

The electrochemical properties of Au electrodes grafted with 4-nitrophenyl and 4-decylphenyl groups have been studied. The electrografting of gold electrode surface with aryl groups was carried out by electroreduction of the corresponding diazonium salts in acetonitrile. The nitrophenyl film growth on gold was examined by atomic force microscopy, electrochemical quartz crystal microbalance and X-ray photoelectron spectroscopy. These measurements showed that a multilayer film of nitrophenyl groups was formed. Cyclic voltammetry was used to study the blocking properties of aryl-modified gold electrodes towards the Fe(CN)₆^3−/4− redox system. The reduction of oxygen was strongly suppressed on these electrodes as evidenced by the rotating disc electrode results.     

Impedimetric Aptasensor for Thrombin Recognition Based on CD Support

We report an aptamer biosensing array for thrombin detection by measuring the electrochemical impedance upon aptamer‐protein formation at the surface of CD‐trodes (GCDTs) in the presence of the redox couple [Fe(CN)₆]^3?/4?. GCDTs are fabricated from recordable compact discs that contain a fine gold layer. The biosensor is constructed by self‐assembling of a thiol‐modified thrombin binding aptamer (TBA) onto a GCDT surface. The sensor reveals good ligand specificity, recognition in a wide range of thrombin concentrations from 20 nM to 1 µM with a limit of detection of 5 nM.     

A highly selective and sensitive cocaine aptasensor based on covalent attachment of the aptamer-functionalized AuNPs onto nanocomposite as the support platform

Based on the conformational changes of the aptamer-functionalized gold nanoparticles (AuNPs) onto MWCNTs/IL/Chit nanocomposite as the support platform, we have developed a sensitive and selective electrochemical aptasensor for the detection of cocaine. The 5′-amine-3′-AuNP terminated aptamer is covalently attached to a MWCNTs/IL/Chit nanocomposite. The interaction of cocaine with the aptamer functionalized AuNP caused the aptamer to be folded and the AuNPs with negative charge at the end of the aptamer came to the near of electrode surface therefore, the electron transfer between ferricyanide (K₃Fe(CN)₆) as redox probe and electrode surface was inhibited. A decreased current of (K₃Fe(CN)₆) was monitored by differential pulse voltammetry technique. In an optimized condition the calibration curve for cocaine concentration was linear up to 11 μM with detection limit (signal-to-noise ratio of 3) of 100 pM. To test the selectivity of the prepared aptasensor sensing platform applicability, some analgesic drugs as the interferes were examined. The potential of the aptasensor was successfully applied for measuring cocaine concentration in human blood serum. Based on our experiments it can be said that the present method is absolutely beneficial in developing other electrochemical aptasensor.     

A novel nitrite sensor based on graphene/polypyrrole/chitosan nanocomposite modified glassy carbon electrode

A novel nitrite sensor was fabricated based on a graphene/polypyrrole/chitosan nanocomposite film modified glassy carbon electrode. The nanocomposite film was characterized by scanning electron microscopy, Fourier transform infrared spectroscopy and Raman spectroscopy. The electron transfer behaviour of the modified electrodes was investigated in [Fe(CN)(6)](3-)/(4-) redox probe using cyclic voltammetry and electrochemical impedance spectroscopy. Differential pulse voltammetry and amperometry were used to study the electrochemical properties of the proposed sensor. Under optimum conditions, the sensor exhibited good reproducibility and stability for nitrite determination. Linear response was obtained in the range of 0.5-722 μM with a detection limit of 0.1 μM (S/N = 3) for nitrite determination.