Acid and basic functionalities of nitrogen and carbon dioxide plasma‐treated polystyrene

The choice of plasma gas can determine the interaction between material and plasma and therefore the applications of the treated materials. Nitrogen plasma can integrate functional groups such as primary amines and carbon dioxide plasma can incorporate carboxylic groups on the surface of polymers. For specific adhesion such as bio‐adhesion, polar groups must be attached to the surface to enhance bio‐film formation but the acidic or basic character also controls the adhesion mechanism. Nitrogen and carbon dioxide plasmas are chosen to treat the surface of polystyrene and to show the effects of different functionalizations, i.e. attachment of acid or basic groups and degradation are compared in the present work. Nitrogen‐containing plasma induces mainly weak degradation at a rate of ～0.13 µg cm^?2s^?1. The roughness of the treated surface remains mostly unchanged. Functionalization leads to amino group attachment at a concentration of 1.2 sites nm^?2. We found that carbon dioxide plasma treatment shows more drastic degradation with a rate three times higher than that of nitrogen plasma and can create more functional groups (4.5 sites nm^?2) at mild plasma treatment. However, the roughness of the surface is altered. In both cases the aromatic groups are degraded through the plasma treatment (again this is more evident with the CO₂ plasma) and the induced functionalization was shown to be quick (the upper monolayer of polystyrene film can be functionalized rapidly). Copyright © 2005 John Wiley & Sons, Ltd.     

Effect of cold plasma process on the surface wettability of NBR and the kerosene resistance of NBR/PTFE composites

In this study, first the acrylonitrile‐butadiene rubber (NBR5080) was modified by argon (Ar), air, and oxygen plasma at low temperature, and the effect of plasma process (power, time, and pressure) on the surface properties of NBR5080, the interfacial properties, physical properties, and the mechanical properties of NBR5080/polytetrafluoroethylene (PTFE) composites were investigated. The state contact angle and the surface free energy were applied to characterize the surface wettability of NBR5080. The scanning electron microscope and the atomic force microscope were used to observe the surface morphology of the NBR5080. The chemical changes on the NBR5080 surface were verified by X‐ray photoelectron spectroscopy. The average water contact angle the NBR5080 declined obviously when NBR5080 was treated by Ar (100 W/600 s/30 Pa). The active oxygen groups were introduced onto the surface of NBR5080 by cold plasma treatment and more active group containing oxygen were observed on the samples treated by Ar plasma. The peel strength between the NBR5080 and the PTFE was increased obviously, which increased from 0 to 44.2 N?m^?1 for Ar plasma treatment. The mass and the dimension of NBR5080 increase sharply after immersing in kerosene, whereas the NBR5080/PTFE composites changed a little. The mechanical properties of NBR5080 and NBR5080/PTFE composites decreased as the immersion time in kerosene increased, but the decreased degree of NBR5080 is higher than NBR5080/PTFE composites.     

Surface modification of polyester by oxygen‐ and nitrogen‐plasma treatment

In this paper, we present a study on the surface modification of polyethyleneterephthalate (PET) polymer by plasma treatment. The samples were treated by nitrogen and oxygen plasma for different time periods between 3 and 90 s. The plasma was created by a radio frequency (RF) generator. The gas pressure was fixed at 75 Pa and the discharge power was set to 200 W. The samples were treated in the glow region, where the electrons temperature was about 4 eV, the positive ions density was about 2 × 10¹⁵ m^?3, and the neutral atom density was about 4 × 10²¹ m^?3 for oxygen and 1 × 10²¹ m^?3 for nitrogen. The changes in surface morphology were observed by using atomic force microscopy (AFM). Surface wettability was determined by water contact angle measurements while the chemical composition of the surface was analyzed using XPS. The stability of functional groups on the polymer surface treated with plasma was monitored by XPS and wettability measurements in different time intervals. The oxygen‐plasma‐treated samples showed much more pronounced changes in the surface topography compared to those treated by nitrogen plasma. The contact angle of a water drop decreased from 75° for the untreated sample to 20° for oxygen and 25° for nitrogen‐plasma‐treated samples for 3 s. It kept decreasing with treatment time for both plasmas and reached about 10° for nitrogen plasma after 1 min of plasma treatment. For oxygen plasma, however, the contact angle kept decreasing even after a minute of plasma treatment and eventually fell below a few degrees. We found that the water contact angle increased linearly with the O/C ratio or N/C ratio in the case of oxygen or nitrogen plasma, respectively. Ageing effects of the plasma‐treated surface were more pronounced in the first 3 days; however, the surface hydrophilicity was rather stable later. Copyright © 2008 John Wiley & Sons, Ltd.     

Raman and Photoluminescence Spectroscopic Detection of Surface‐Bound Li+O2− Defect Sites in Li‐Doped ZnO Nanocrystals Derived from Molecular Precursors

We present a detailed study of Raman spectroscopy and photoluminescence measurements on Li‐doped ZnO nanocrystals with varying lithium concentrations. The samples were prepared starting from molecular precursors at low temperature. The Raman spectra revealed several sharp lines in the range of 100–200 cm^?1, which are attributed to acoustical phonons. In the high‐energy range two peaks were observed at 735 cm^?1 and 1090 cm^?1. Excitation‐dependent Raman spectroscopy of the 1090 cm^?1 mode revealed resonance enhancement at excitation energies around 2.2 eV. This energy coincides with an emission band in the photoluminescence spectra. The emission is attributed to the deep lithium acceptor and intrinsic point defects such as oxygen vacancies. Based on the combined Raman and PL results, we introduce a model of surface‐bound LiO₂ defect sites, that is, the presence of Li⁺O₂^? superoxide. Accordingly, the observed Raman peaks at 735 cm^?1 and 1090 cm^?1 are assigned to Li? O and O? O vibrations of LiO₂.     

A Plasma‐Triggered O−S Bond and P−N Junction Near the Surface of a SnS2 Nanosheet Array to Enable Efficient Solar Water Oxidation

A photoelectrochemical (PEC) cell can split water into hydrogen and oxygen with the assistance of solar illumination. However, its application is still limited by excessive bulk carrier recombination and sluggish surface oxygen evolution reaction (OER) kinetics. Taking SnS₂ as an example, a promising layered optoelectronic semiconductor, Ar plasma treatment strategy was used to introduce a SnS/SnS₂ P?N heterojunction and O?S bond near the surface of a SnS₂ nanosheet array, simultaneously increasing the separation efficiency of photogenerated electron–hole pairs in the bulk and lowering the OER overpotential at the surface. The onset potential of the plasma‐treated SnS₂ nanosheet array shifts negatively to 0.16 V, and the photocurrent density at 1.23 V vs. RHE boosts to 2.15 mA cm^?2, which is 7 times that of pristine SnS₂. This work demonstrates a facile plasma treatment strategy to modulate the energy band structure and surface chemical states for improved PEC performance.     

Identifying the O2 diffusion and reduction mechanisms on CeO2 electrolyte in solid oxide fuel cells: A DFT + U study

The interactions and reduction mechanisms of O₂ molecule on the fully oxidized and reduced CeO₂ surface were studied using periodic density functional theory calculations implementing on‐site Coulomb interactions (DFT + U) consideration. The adsorbed O₂ species on the oxidized CeO₂ surface were characterized by physisorption. Their adsorption energies and vibrational frequencies are within ?0.05 to 0.02 eV and 1530–1552 cm^?1, respectively. For the reduced CeO₂ surface, the adsorption of O₂ on Ce⁴⁺, one‐electron defects (Ce³⁺ on the CeO₂ surface) and two‐electron defects (neutral oxygen vacancy) can alter geometrical parameters and results in the formation of surface physisorbed O₂, O₂^a? (0 < a < 1), superoxide (O₂^?), and peroxide (O₂^2?) species. Their corresponding adsorption energies are ?0.01 to ?0.09, ?0.20 to ?0.37, ?1.34 and ?1.86 eV, respectively. The predicted vibrational frequencies of the peroxide, superoxide, O₂^a? (0 < a < 1) and physisorbed species are 897, 1234, 1323–1389, and 1462–1545 cm^?1, respectively, which are in good agreement with experimental data. Potential energy profiles for the O₂ reduction on the oxidized and reduced CeO₂ (111) surface were constructed using the nudged elastic band method. Our calculations show that the reduced surface is energetically more favorable than the unreduced surface for oxygen reduction. In addition, we have studied the oxygen ion diffusion process on the surface and in bulk ceria. The small barrier for the oxygen ion diffusion through the subsurface and bulk implies that ceria‐based oxides are high ionic conductivity at relatively low temperatures which can be suitable for IT‐SOFC electrolyte materials. © 2009 Wiley Periodicals, Inc. J Comput Chem, 2009     

Surface‐initiated ring‐opening polymerization of p‐dioxanone on Wang resin bead

Biodegradable poly(p‐dioxanone) (PPDO) was formed on Wang resin surface by surface‐initiated ring‐opening polymerization (SI‐ROP). The SI‐ROP of p‐dioxanone (PDO) was achieved by heating a mixture of Tin(II) bis(2‐ethylhexanoate) [Sn(Oct)₂], hydroxyl functionalized Wang resin, and PDO in anhydrous toluene at 80 °C. The resultant polymer‐grafted Wang resin (Wang‐g‐PPDO) was characterized by fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), optical microscopy (OM), and field‐emission scanning electron microscopy (FE‐SEM). The FTIR spectra of Wang‐g‐PPDO show peak characteristic of PPDO at 2943 cm^?1 (? C? H stretch), at 1741 cm^?1 (? C?O stretch), and 1136 cm^?1 (C? O? C stretch) indicating the formation of ester linkage between PPDO and hydroxyl terminated Wang resin. The DSC thermogram show melting peak corresponding to PPDO polymer on Wang resin surface. Thermogravimetric investigation shows increase in PPDO content on the Wang resin surface in terms of percentage of weight loss with increase in reaction time. The OM and SEM photographs clearly show the formation of PPDO polymer on the Wang resin surface without altering the spherical nature of Wang resin bead. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1178–1184, 2008     

Surface characterization and electrical property of carbon fibers modified by air oxidation

Polyacrylonitrile‐based carbon fibers were modified by oxidation in air, and a systematic study of surface groups and surface resistance at different treated temperatures was made. Progressive fiber weight loss occurred with increasing extents of air oxidation, and it was approximately proportional to the extent of air oxidation from the onset of oxidation up to 400 °C. At this point 4.4% of the initial fiber weight had been lost. A faster loss of weight occurred as the extent of air oxidation increased from 400 °C to 700 °C. X‐ray photoelectron spectroscopy studies (C 1s and O 1s) indicated that the oxygen/carbon atomic ratio rose rapidly from 2.64% (as‐received carbon fiber) to 42.83% as the oxidation temperature was increased to 400 °C. Fourier transform infrared spectra showed the relative intensity of the peaks at about 3440 cm^?1 from ―OH stretching vibrations and at 1634 cm^?1 from ―C?O stretching vibrations increased significantly at 400 °C. FESEM micrographs showed that as‐received fibers show relatively smooth surface. With oxidation temperature increasing, the fiber surface was rougher. The surface resistance of treated carbon fibers decreased obviously with increasing oxidation temperatures. The most decrease was about 100% at 400 °C. Copyright © 2014 John Wiley & Sons, Ltd.     

Interaction between model poly(ethylene terephthalate) thin films and weakly ionised oxygen plasma

Model films of poly(ethylene terephthalate) were treated by oxygen plasma in order to quantify the etching rate and estimate the contribution of charged and neutral particles to the reaction probability. Model films with a thickness of 50 nm were deposited on a quartz crystal of a microbalance (QCM) by spin‐coating technique. The samples were exposed to oxygen plasma with the positive ion density of 4 × 10¹⁵ m^?3 and neutral oxygen atom density of 6 × 10²¹ m^?3. The etching rate was determined from the QCM signal and was 4.7 nm s^?1. The etching was found rather inhomogeneous as the atomic force microscopic images showed an increase of the surface roughness as a result of plasma treatment. The model films were completely removed from the surface of the quartz crystals in about 12 s. Knowing the etching rate and the flux of oxygen atoms to the surface allowed for calculation of the reaction probability which was found to be rather low at the value of 1.6 × 10^?4. Copyright © 2011 John Wiley & Sons, Ltd.     

Surface analysis of plasma‐treated polydimethylsiloxane by x‐ray photoelectron spectroscopy and surface voltage decay

Surface states of polydimethylsiloxane (PDMS) treated by plasma were investigated by x‐ray photoelectron spectroscopy and surface voltage decay. X‐ray photoelectron spectroscopy confirmed the formation of a silica‐like (SiO_x, x = 3–4) oxidative surface layer. This layer increased in thickness with increasing exposure duration of plasma. Plasma exposure lowers the surface resistivity from 1.78 × 10¹⁴ to 1.09 × 10¹³ Ω □^?1 with increasing plasma treatment time. By measuring the decay time constant of surface voltage, the calculated surface resistivity was compared with the value measured directly by a voltage–current method; good agreement between the two methods was obtained. It was observed that plasma treatment led to a decrease in the thermal activation energy of the surface conduction from 31.0 kJ mol^?1 for an untreated specimen to 21.8 kJ mol^?1 for a plasma‐treated specimen for 1 h. Our results allow the examination of effects of plasma on the electrical properties of PDMS. Copyright © 2003 John Wiley & Sons, Ltd.     

Synergy of Epoxy Chemical Tethers and Defect‐Free Graphene in Enabling Stable Lithium Cycling of Silicon Nanoparticles

We report a new approach for nanosilicon–graphene hybrids with uniquely stable solid electrolyte interphase. Expanded graphite is gently exfoliated creating “defect‐free” graphene that is non‐catalytic towards electrolyte decomposition, simultaneously introducing high mass loading (48 wt. %) Si nanoparticles. Silane surface treatment creates epoxy chemical tethers, mechanically binding nano‐Si to CMC binder through epoxy ring‐opening reaction while stabilizing the Si surface chemistry. Epoxy‐tethered silicon pristine–graphene hybrid “E‐Si‐pG” exhibits state‐of‐the‐art performance in full battery opposing commercial mass loading (12 mg cm^?2) LiCoO₂ (LCO) cathode. At 0.4 C, with areal capacity of 1.62 mAh cm^?2 and energy of 437 Wh kg^?1, achieving 1.32 mAh cm^?2, 340.4 Wh kg^?1 at 1 C. After 150 cycles, it retains 1.25 mAh cm^?2, 306.5 Wh kg^?1. Sputter‐down XPS demonstrates survival of surface C‐Si‐O‐Si groups in E‐Si‐pG after repeated cycling. The discovered synergy between support defects, chemical‐mechanical stabilization of Si surfaces, and SEI‐related failure may become key LIB anode design rule.     

Rapid Synthesis of Cobalt Nitride Nanowires: Highly Efficient and Low‐Cost Catalysts for Oxygen Evolution

Electrochemical splitting of water to produce hydrogen and oxygen is an important process for many energy storage and conversion devices. Developing efficient, durable, low‐cost, and earth‐abundant electrocatalysts for the oxygen evolution reaction (OER) is of great urgency. To achieve the rapid synthesis of transition‐metal nitride nanostructures and improve their electrocatalytic performance, a new strategy has been developed to convert cobalt oxide precursors into cobalt nitride nanowires through N₂ radio frequency plasma treatment. This method requires significantly shorter reaction times (about 1 min) at room temperature compared to conventional high‐temperature NH₃ annealing which requires a few hours. The plasma treatment significantly enhances the OER activity, as evidenced by a low overpotential of 290 mV to reach a current density of 10 mA cm^?2, a small Tafel slope, and long‐term durability in an alkaline electrolyte.     

High‐Energy Rechargeable Metallic Lithium Battery at −70 °C Enabled by a Cosolvent Electrolyte

Lithium metal is an ideal anode for high‐energy rechargeable batteries at low temperature, yet hindered by the electrochemical instability with the electrolyte. Concentrated electrolytes can improve the oxidative/reductive stability, but encounter high viscosity. Herein, a co‐solvent formulation was designed to resolve the dilemma. By adding electrochemically “inert” dichloromethane (DCM) as a diluent in concentrated ethyl acetate (EA)‐based electrolyte, the co‐solvent electrolyte demonstrated a high ionic conductivity (0.6 mS cm^?1), low viscosity (0.35 Pa s), and wide range of potential window (0–4.85 V) at ?70 °C. Spectral characterizations and simulations show these unique properties are associated with the co‐solvation structure, in which high‐concentration clusters of salt in the EA solvent were surrounded by mobile DCM diluent. Overall, this novel electrolyte enabled rechargeable metallic Li battery with high energy (178 Wh kg^?1) and power (2877 W kg^?1) at ?70 °C.     

Rapid surface functionalization of poly(ethersulphone) foils using a highly reactive oxygen‐plasma treatment

We present a study of the oxygen‐plasma functionalization of polyethersulphone (PES). PES samples were exposed to a weakly ionized, highly dissociated oxygen plasma, with an electron temperature of 5 eV and a positive ion density of 8 × 10¹⁵ m^?3, and its afterglow, in which the density of charged particles was negligibly low and the density of neutral oxygen atoms was 4 × 10²¹ m^?3. The wettability of the samples was determined by measuring the contact angle of a water drop, while the appearance of the functional groups on the surface of the samples was determined using high‐resolution conventional XPS. The samples were saturated with surface functional groups, both in the plasma and in the afterglow region, after 1 s of treatment time. The results are explained by the high flux of oxygen atoms on the sample surface and the characteristics of the oxygen plasma. Copyright © 2007 John Wiley & Sons, Ltd.     

Double Perovskite LaFexNi1−xO3 Nanorods Enable Efficient Oxygen Evolution Electrocatalysis

Perovskite‐based electrocatalysts are one of the most promising materials for oxygen evolution reaction (OER), but their activity and durability are still far from desirable. Herein, we demonstrate that the double perovskite LaFe_xNi_1?xO₃ (LFNO) nanorods (NRs) can be adopted as highly active and stable OER electrocatalysts. The optimized LFNO‐II NRs with Ni/Fe ratio of 8:2 achieve a low overpotential of 302 mV at 10 mA cm^?2 and a small Tafel slope of 50 mV dec^?1, outperforming those of the commercial Ir/C. The LFNO‐II NRs also show high OER stability with slight current decrease after 20 h. The enhanced activity is explained by the improved surface area, tailored electronic structure as well as strong hybridization between O and Ni.     

From Linear to Angular Isomers: Achieving Tunable Charge Transport in Single‐Crystal Indolocarbazoles Through Delicate Synergetic CH/NH⋅⋅⋅π Interactions

Weak intermolecular interaction in organic semiconducting molecular crystals plays an important role in molecular packing and electronic properties. Here, four five‐ring‐fused isomers were rationally designed and synthesized to investigate the isomeric influence of linear and angular shapes in affecting their molecular packing and resultant electronic properties. Single‐crystal field‐effect transistors showed mobility order of 5,7‐ICZ (3.61 cm² V^?1 s^?1) >5,11‐ICZ (0.55 cm² V^?1 s^?1) >11,12‐ICZ (ca. 10^?5 cm² V^?1 s^?1) and 5,12‐ICZ (ca. 10^?6 cm² V^?1 s^?1). Theoretical calculations based on density functional theory (DFT) and polaron transport model revealed that 5,7‐ICZ can reach higher mobilities than the others thanks to relatively higher hole transfer integral that links to stronger intermolecular interaction due to the presence of multiple NH???π and CH???π(py) interactions with energy close to common NH???N hydrogen bonds, as well as overall lower hole‐vibrational coupling owing to the absence of coupling of holes to low frequency modes due to better π conjugation.     

Topochemical Synthesis of Two‐Dimensional Transition‐Metal Phosphides Using Phosphorene Templates

Transition‐metal phosphides (TMPs) have emerged as a fascinating class of narrow‐gap semiconductors and electrocatalysts. However, they are intrinsic nonlayered materials that cannot be delaminated into two‐dimensional (2D) sheets. Here, we demonstrate a general bottom‐up topochemical strategy to synthesize a series of 2D TMPs (e.g. Co₂P, Ni₁₂P₅, and Co_xFe_2?xP) by using phosphorene sheets as the phosphorus precursors and 2D templates. Notably, 2D Co₂P is a p‐type semiconductor, with a hole mobility of 20.8 cm² V^?1 s^?1 at 300 K in field‐effect transistors. It also behaves as a promising electrocatalyst for the oxygen evolution reaction (OER), thanks to the charge‐transport modulation and improved surface exposure. In particular, iron‐doped Co₂P (i.e. Co_1.5Fe_0.5P) delivers a low overpotential of only 278 mV at a current density of 10 mA cm^?2 that outperforms the commercial Ir/C benchmark (304 mV).     

Pressure effects on cation migration in 2,5‐di‐tert‐butyl‐1,4‐benzoquinone radical anion

Pressure effects on the two‐site jumping of sodium and potassium cations in a 2,5‐di‐tert‐butyl‐1,4‐benzoquinone ion pair have been studied using a high‐pressure EPR technique. The rate constants of the intramolecular and intermolecular migrations for Na⁺ and K⁺ were determined from an EPR spectral simulation. The migration rates were found to be accelerated by increasing the external pressure. Using the pressure dependence of the migration rates, we estimated the activation volumes of the intramolecular (ΔV₁^?) and intermolecular (ΔV₂^?) processes for the Na⁺ and K⁺ migrations: ΔV₁^? = ?5.3 cm³ mol^?1 and ΔV₂^? = ?29 cm³ mol^?1 for Na⁺, and ΔV₁^? = ?8.3 cm³ mol^?1 and ΔV₂^? = ?0.85 cm³ mol^?1 for K⁺. Based on the results, the mechanisms for the two‐site jumping of Na⁺ and K⁺ are discussed in terms of volume. © 2001 John Wiley & Sons, Inc. Int J Chem Kinet 33: 397–401, 2001     

Low bandgap π‐conjugated copolymers based on fused thiophenes and benzothiadiazole: Synthesis and structure‐property relationship study

A series of low bandgap conjugated polymers consisting of benzothiadiazole alternating with dithienothiophene (DTT) or dithienopyrrole (DTP) unit with or without 3‐alkylthiophene bridge have been synthesized. Effect of the fused rings and 3‐alkylthiophene bridge on the thermal, optical, electrochemical, charge transport, and photovoltaic properties of these polymers have been investigated. These polymers show broad absorption extending from 300 to 1000 nm with optical bandgaps as low as 1.2 eV; the details of which can be varied either by incorporating 3‐alkylthiophene bridge or by replacing DTT with DTP. The LUMO levels (?2.9 to ?3.3 eV) are essentially unaffected by the specific choice of donor moiety, whereas the HOMO levels (?4.6 to ?5.6 eV) are more sensitive to the choice of donor. The DTT and DTP polymers with 3‐alkylthiophene bridge were found to exhibit hole mobilities of 8 × 10^?5 and 3 × 10^?2 cm² V^?1 s^?1, respectively, in top‐contact organic field‐effect transistors. Power conversion efficiencies in the range 0.17–0.43% were obtained under simulated AM 1.5, 100 mW cm^?2 irradiation for polymer solar cells using the DTT and DTP‐based polymers with 3‐alkylthiophene bridge as donor and fullerene derivatives as acceptor. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5498–5508, 2009     

Electrochemical Treatment for Effectively Tuning Thermoelectric Properties of Free‐Standing Poly(3‐methylthiophene) Films

The degree of oxidation of conducting polymers has great influence on their thermoelectric properties. Free‐standing poly(3‐methylthiophene) (P3MeT) films were prepared by electrochemical polymerization in boron trifluoride diethyl etherate, and the fresh films were treated electrochemically with a solution of propylene carbonate/lithium perchlorate as mediator. The conductivity of the resultant P3MeT films depends on the doping level, which is controlled by a constant potential from ?0.5 to 1.4 V. The optimum electrical conductivity (78.9 S cm^?1 at 0.5 V) and a significant increase in the Seebeck coefficient (64.3 μV K^?1 at ?0.5 V) are important for achieving an optimum power factor at an optimal potential. The power factor of electrochemically treated P3MeT films reached its maximum value of 4.03 μW m^?1 K^?2 at 0.5 V. Moreover, after two months, it still exhibited a value of 3.75 μW m^?1 K^?2, and thus was more stable than pristine P3MeT due to exchange of doping ions in films under ambient conditions. This electrochemical treatment is a significant alternative method for optimizing the thermoelectric power factor of conducting polymer films.