Aging and cold crystallization of melt‐extruded poly(trimethylene terephthalate) films

We analyzed the thermal crystallization, glass‐transition behavior, and mechanical properties of melt‐extruded poly(trimethylene terephthalate) (PTT) films to investigate their physical aging and annealing effects. The physical aging and annealing of PTT films had an influence on the glass‐transition temperature, recrystallization behavior, and mechanical properties. When samples were aged at an ambient temperature, the crystallization temperature decreased largely within 5 h, the heat of crystallization increased, and the breaking stress and breaking elongation increased. The glass‐transition temperature of annealed samples, which was obtained from differential scanning calorimetry and dynamic mechanical measurements, increased with increasing annealing temperature below 80 °C but decreased above that temperature. In addition, the glass‐transition temperature and modulus of annealed samples were largely affected by the annealing time; in particular, they increased sharply within 1 h on annealing at 50 °C. Consequently, the change in the glass‐transition temperature on annealing was ascribed to the fact that the molecular constraint due to recrystallization and the mobility of rigid amorphous PTT chains competed with each other, being dependent on the annealing temperature. The mechanical properties of aged samples were closely related to their cold‐crystallization behavior. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1920–1927, 2001     

Dependence of dielectric,ferroelectric, and piezoelectric properties on crystalline properties of p(VDF‐co‐TrFE) copolymers

Thermal processing at various temperatures has been used to fabricate poly(vinylidene fluoride‐co‐trifluoroethylene) [P(VDF‐co‐TrFE)] films with varied crystalline properties in an attempt to improve their piezoelectric properties. Although the dielectric constant of the films annealed at higher temperature is smaller than that of cooled and quenched ones, it has been shown that the annealed films possess larger crystallinity and stacked lamellar crystal grain size. The ferroelectric domains deriving from crystal region in all the samples are effectively improved by hot polarization. As a result, the remnant polarizations (P_r) and coercive electric field (E_c) of the corresponding films are improved at a low frequency due to the response of dipoles in crystal phase, and the largest piezoelectric constant in the longitudinal thickness mode (d₃₃=?25 pC/N) is obtained in an annealed copolymer film. The results illustrate improving the crystal structure of P(VDF‐co‐TrFE) is an effective way to realize high electromechanical properties, which provides broadly applied scenery for this kind of copolymer in piezoelectric components. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Structure evolution of α′‐phase poly(lactic acid)

Poly(lactic acid) films consisting of α′‐forms were prepared and uniaxially drawn. The effects of the draw rate at temperatures above the glass transition temperature on chain conformation, degree of crystallinity, and crystalline phase transformation were investigated by a combination of vibrational spectroscopy (infrared and Raman), differential scanning calorimetry, and wide‐angle X‐ray diffraction (WAXD). It was established that the α′‐crystal's phase of poly(lactic acid) films does not transform into either an α or β crystals on uniaxial drawing at a fixed draw ratio of 4. However, the degree of crystallinity was significantly increased on deformation. The structural change as a function of deformation also promotes an increase in the strain‐induced enthalpic relaxation endothermic peak appearing near the glass transition region. While the overall changes in physical properties can be attributed to the changes in the degree of crystallinity as a function of strain rate, polarized Raman spectra, and WAXD clearly illustrated changes and the differences in the amorphous and crystalline orientation as a function of processing conditions. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 49: 1446–1454, 2011     

Annealing behavior of gel‐spun polyethylene fibers at temperatures lower than needed for significant shrinkage

The annealing at 373 K of ultrastrong, gel‐spun polyethylene (PE) has been studied. At this temperature, the fibers show no significant shrinkage. Still, a significant decrease in the mechanical properties is observed. The fibers have been analyzed with differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), atomic force microscopy (AFM), and small‐angle X‐ray scattering (SAXS). During the annealing, the glass transition of the intermediate phase is exceeded, as shown by DSC. When split for structure analysis by AFM, the annealed fibers undergo plastic deformation around the base fibrils instead of brittle fracture. The quasi‐isothermal TMDSC experiments are compared to the minor structural changes seen with SAXS and AFM. The loss of performance of the PE fibers at 373 K is suggested to be caused by the oriented intermediate phase, and not by major changes in the structure or morphology. The overall metastable, semicrystalline structure is shown by TMDSC to posses local regions that can melt reversibly. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 403–417, 2003     

Novel side‐chain liquid‐crystalline polyimide for film materials

A novel side‐chain liquid‐crystalline polyimide (SLCPI) was prepared via copolycondensation from 3,5‐diamino‐benzonic‐4′‐biphenyl ester, 4,4′‐diamino‐ biphenyl ether, and 3,3′,4,4′‐oxydiphthalic dianhydride. The energy‐minimized structure and liquid crystallinity of SLCPI were investigated by molecular modeling, differential scanning calorimetry (DSC), wide‐angle X‐ray scattering, and polarized optical microscopy, respectively. The results indicated that this polyimide (PI) with side‐chain mesogenic units exhibited a nematic NI phase. Because of the in situ self‐reinforcement of side‐chain mesogenic units, the improved tensile strength and modulus of PI films reached 270% and 300%, respectively. The coefficient of thermal expansion of films decreased by 40%. DSC and thermogravimetric analyses indicated that the phase‐transition temperature of SLCPI was above 240 °C, and the 5% weight‐loss temperature was above 520 °C. Moreover, copolycondensation of two diamines with dianhydride and incorporation of pendent mesogenic units diminished the regularity and symmetry of main chains; as a result, SLCPI exhibits good film processability. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 554–559, 2003     

Crystalline structure and morphology of biaxially oriented polyamide‐11 films

The effect of the uniaxial and biaxial stretching and subsequent solution annealing of extrusion‐cast polyamide‐11 films on the crystalline structure and morphology was investigated with differential scanning calorimetry, wide‐angle X‐ray diffraction (WAXD), Fourier transform infrared spectroscopy, and small‐angle X‐ray scattering (SAXS). The extrusion‐cast polyamide‐11 films exhibited elevations in the glass‐transition and cold‐crystallization temperatures with a constant crystallinity and a constant melting point during aging under room conditions (20–26 °C and 20–31% relative humidity). WAXD and SAXS suggested that chain‐folded lamellae of coexisting α‐ and β‐crystals existed in all the stretched polyamide‐11 films. WAXD pole figures indicated that hydrogen bonds in the hydrogen‐bonded sheets of these two crystalline forms apparently formed between antiparallel chain molecules. The unit cell parameters [a = 9.52 Å, b = 5.35 Å, c = 14.90 Å (chain axis), α = 48.5°, β = 90°, and γ = 74.7° for a triclinic α form and a = 9.52 Å, b = 14.90 Å (chain axis), c = 4.00 Å, α = 90°, β = 67.5°, and γ = 90° for a monoclinic β form] for polyamide‐11 crystals were proposed according to the results of this study and the results of previous investigators. The unit cell parameters of the stretched extrusion‐cast polyamide‐11 films varied, depending on the stretching conditions (the stretch temperature and stretch ratio). As the stretch temperature and stretch ratio were increased, the crystal became more similar to the form described previously and was accompanied by an increase in the long spacing of crystalline lamellae. Annealing the stretched films in a boiling 20% formic acid solution made slightly more perfected crystals. The hydrogen‐bonding α(010) + β(002) planes, which are nearly parallel to both amide group planes and zigzag methylene sequence planes of the biaxially stretched films were found to be parallel to the film surface. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 2624–2640, 2002     

Fibrillar structure of resorbable microblock copolymers based on 1,5‐dioxepan‐2‐one and ε‐caprolactone

The copolymerization of 1,5‐dioxepan‐2‐one (DXO) and ε‐caprolactone, initiated by a five‐membered cyclic tin alkoxide initiator, was performed in chloroform at 60 °C. Copolymers with different molar ratios of DXO (25, 40, and 60%) were synthesized and characterized. ¹³C NMR spectroscopy of the carbonyl region revealed the formation of copolymers with a blocklike structure. Differential scanning calorimetry measurements showed that all the copolymers had a single glass transition between ?57 and ?49 °C and a melting temperature in the range of 30.1–47.7 °C, both of which were correlated with the amount of DXO. An increase in the amount of DXO led to an increase in the glass‐transition temperature and to a decrease in the melting temperature. Dynamic mechanical thermal analysis measurements confirmed the results of the calorimetric analysis, showing a single sharp drop in the storage modulus in the temperature region corresponding to the glass transition. Tensile testing demonstrated good mechanical properties with a tensile strength of 27–39 MPa and an elongation at break of up to 1400%. The morphology of the copolymers was examined with polarized optical microscopy and atomic force microscopy; the films that crystallized from the melt showed a short fibrillar structure (with a length of 0.05–0.4 μm) in contrast to the untreated solution‐cast films. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2412–2423, 2003     

Effect of annealing on the structure and properties of poly(vinylidene fluoride) β‐form films

Oriented poly(vinylidene fluoride) (PVDF) films consisting of β crystals were prepared by the solid‐state coextrusion (SC) of a gel film near the melting temperature (T_m) and by conventional cold tensile drawing (TD) of a melt‐quenched film. These films were annealed over the temperature range of 75–190 °C (below and above the static T_m) while the sample length was kept constant or constant loads were applied. After annealing with the sample length kept constant, the dynamic Young's modulus markedly decreased because of the relaxation of oriented amorphous chains, as shown by infrared spectroscopy. In contrast, annealing under a constant load improved the chain orientation in both the crystalline and amorphous regions, resulting in an increase in the modulus from an initial 10.5 to 14.3 GPa for the SC and from an initial 3.3 to 4.8 GPa for the TD. The SC, annealed at 190 °C with a constant load corresponding to an initial tension of 200 MPa, exhibited an extreme crystalline‐chain orientation of 0.998 and a modulus of 14.3 GPa, among the highest values ever reported for PVDF. Although the remanent polarization (P_r) of the TD increased slightly from the initial 62 to 68 mC/m², P_r of the SC stayed constant at 100 mC/m² independently of the annealing conditions. This suggests that the P_r value of 100 mC/m² approached the equilibrium value for this PVDF sample containing 3.5 mol % structural defects. Therefore, although the modulus and P_r of the TD increased slightly with annealing, the maximum values achieved by annealing were markedly lower than those of the SC and annealed SC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1701–1712, 2003     

Online monitoring of birefringence development in heat‐setting polymer films with a fast dual‐wavelength optical technique. I. Uniaxially oriented poly(ethylene naphthalate)

The purpose of this article is to study the fast structural changes that take place during the deformation and heat setting of uniaxially preoriented poly(ethylene 2,6‐naphthalate) films. For this purpose, an online birefringence measurement system coupled with a heat‐setting oven was used. In the online birefringence system, whose details were reported previously (H. Venkatesvaran and M. Cakmak, SPE ANTEC Tech Pap 1993, 39, 257; H. Venkatesvaran and M. Cakmak, Polym Eng Sci 2001, 41, 341), a green and red laser is passed through the films being annealed in a heat‐setting chamber; the resulting data are analyzed for the details of structural mechanisms that take place during this process. This technique is shown to be capable of detecting reversals in birefringence development; as a result, complex sequences of structural evolution can be tracked. The design of this system allows one to observe not only the increase or decrease in birefringence during the course of the heat‐setting process but also the rate dependencies on processing variables. In this study, we establish that the rate of structural rearrangement, as detected by birefringence, depends strongly on the state of the pre‐existing chain orientation and the level of crystallinity. Increased levels of preorientation in the films results in decreases in the rate of birefringence change during heat setting. This is primarily attributed to the increased levels of steric hindrance developed with the increase in orientation and crystallinity in the preoriented samples. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 1107–1121, 2001     

High‐performance poly(ethylene‐2,6‐naphthalate) fiber prepared by high‐tension annealing

A high‐tension annealing (HTA) method has been applied to zone‐annealed poly(ethylene‐2,6‐naphthalate) (PEN) fibers in order to further improve their mechanical properties. The HTA treatment was carried out under an applied tension of 428 MPa at a treating temperature of 175 °C. The applied tension was close to the tensile strength at 175 °C. The resulting HTA fiber had a birefringence of 0.492 and degree of crystallinity of 57%. Wide‐angle X‐ray diffraction (WAXD) photographs of the HTA fibers showed three reflections (010, 100, and 1 10) attributed to an α form crystal, but no (020) reflection attributed to a β form was observed in the equator. The tensile modulus and tensile strength increased with processing, and the HTA fiber had a maximum modulus of 33 GPa, a tensile strength of 1.1 GPa, and a storage modulus of 33 GPa at 25 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 61–67, 2000     

The brittle–ductile transition induced by thermal ageing of toluene cast poly(2,6‐dimethyl‐1,4‐phenylene oxide) as observed by interfacial friction

The interfacial shear stress of toluene cast poly(2,6‐dimethyl‐1,4‐phenylene oxide) films has been studied as a function of annealing temperature. The surface topography of these films was studied by scanning probe microscopy following a single sliding pass. Casting from toluene results in a semicrystalline film with a rigid amorphous phase and containing a small amount of residual solvent that exhibits a higher interfacial shear stress than a high temperature annealed solvent‐free amorphous film. Films containing small amounts of toluene exhibit a wear pattern consisting of ripples oriented perpendicular to the sliding direction following a single sliding pass. These results support the notion that the interfacial shear stress is a function of the shear yield stress, and, that during sliding friction tensile stresses must form at the polymer surface. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1637–1643, 2009     

Melt‐processable blends of ionic poly(p‐phenylene terephthalamide) and poly(4‐vinylpyridine): Relaxation behavior

Melt‐processable blends were prepared from rigid molecules of an ionically modified poly(p‐phenylene terephthalamide) (PPTA) and flexible‐coil molecules of poly(4‐vinylpyridine) (PVP). Dynamic mechanical analyses of blends with 50% or more of the ionic PPTA component revealed the presence of two distinct phases. The glass‐transition temperature of the more stable, ionic PPTA‐rich phase increased linearly with the ionic PPTA content. The second phase present in these blends was an ionic PPTA‐poor, or a PVP‐rich, phase. For this phase, a reasonably good fit of the data, showing the glass‐transition temperature as a function of the ionic PPTA content, was achieved between the results of this study and the reported results of previous investigation of molecular composites of the same two components with ionic PPTA contents of 15 wt % or less. The possible influence of annealing on the blend structure of a 90/10 blend of ionic PPTA and PVP was examined. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1468–1475, 2003     

Room‐temperature processing of π‐conjugated oligomers into uniaxially oriented monodomain films on coumarin‐based photoalignment layers

Photoalignment layers comprising Polymer 1 were prepared using linearly polarized UV‐irradiation for chloroform‐vapor annealing of π‐conjugated oligomer films, both processes conducted at room temperature. The resultant uniaxially oriented monodomain films exhibited S = 0.74 (at P_r = 0.90) and 0.82 (at P_r = 0.95) in OF and OF2T films, respectively, apparently limited by film dewetting in comparison to S = 0.82 ± 0.01 from thermal annealing on rubbed polyimide alignment and Polymer 1 photoalignment layers. The time to arrive at maximum S values varied from 5–10 s to 6–8 min on rubbed polyimide alignment layers and Polymer 1 photoalignment layer, respectively, because of favorable π–π interactions enhanced by rubbing. In contrast, PF2T could not be oriented on either type of alignment layers after annealing under saturated chloroform vapor up to 14 h. Annealing of an OF2T film under saturated chlorobenzene vapor at room temperature permitted lyotropic nematic mesomorphism to be observed in situ, which is equivalent to thermotropic nematic mesomorphism as the driving force behind thermal annealing. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Effect of postcasting heat‐treatment on the structure and properties of semicrystalline phase‐inversion poly(vinylidene fluoride) membranes

Microporous PVDF membranes were prepared by immersion‐precipitation in 1‐octanol of casting dopes dissolved at different temperatures, with dissolution temperature affecting strongly the membrane microstructure. The effect of postcoagulation thermal annealing, which is an additional thermal parameter, on membrane microstructure and properties is probed herein. Membranes obtained were annealed at temperatures up to 160 °C, which is close to the melting point of PVDF polymer. Annealing leads to a substantial modification of the nano‐scale fine structure of the membranes, while the overall‐microporous structure is preserved. At elevated annealing temperatures, nano‐grains, fibrils, and stick‐like crystalline entities gradually eclipse, while globules develop more robust connections based on wide bands of crystal elements. Probing by X‐ray diffraction and dynamic scanning calorimetry shows that crystallinity increases when annealing temperature and time are increased. As regards mechanical properties, the tensile strength of the membranes can be enhanced substantially, up to about 10 times, upon appropriate high temperature prolonged annealing. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1880–1893, 2009     

The effect of proton irradiation on the melting and isothermal crystallization of poly(ether‐ether‐ketone)

Amorphous poly(ether‐ether‐ketone) (PEEK) progressively crosslinks on irradiation with 11.0 MeV protons, and this has a marked effect on the extent of crystallinity that subsequently develops and on the kinetics of the high temperature isothermal crystallization. The extent of crystallinity with time was analyzed using the Avrami equation, and the temperature dependence of the rate constants was analyzed in terms of nucleation theory. While irradiation inhibits the overall rates of crystallization by the reduction in the mobility of the chain segments as observed by the progressive increase in the glass transition temperature, it also alters the fold surface free energy. The observed melting points were consistent with depression of the equilibrium melting point by the crosslinks produced by irradiation. These two effects alone are sufficient to account for the inhibition of crystallization on irradiation of PEEK by protons. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1094–1103, 2008     

Deformation and fracture behavior of poly(vinylidene fluoride‐trifluorethylene) ferroelectric copolymer films under uniaxial tension

The deformation and fracture behavior under uniaxial tension was characterized for P(VDF‐TrFE) 68/32 mol % copolymer films prepared under two different processing conditions. It was found that the copolymer films prepared by solution casting and then annealing show a typical polymeric brittle fracture feature. For the copolymer films prepared by stretching the solution‐cast films and then annealing process, a typical linearly strengthening stage occurs in the stress–strain curve after yielding, and the polymer film samples fracture at a much larger maximum strain and a higher tensile strength than those prepared by the former process. SEM observation and XRD analysis were carried out to examine the morphology and microstructure change during uniaxial tension. The results show that for the stretched film samples, the polymer chains undergo slipping or further reorientation during uniaxial tension, causing the increase of the peak intensity in the X‐ray diffraction pattern. For the directly annealed ones, no yielding phenomenon is observed and there is no apparent X‐ray diffraction intensity change. It was suggested that the highly‐oriented fibril structure of the stretched film samples contributes to the linearly strengthening stage after yielding in the stress–strain curve. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3255–3260, 2005     

Enhanced electrical properties of highly oriented poly(vinylidene fluoride) films prepared by solid‐state coextrusion

Oriented poly(vinylidene fluoride) (PVDF) films with β‐form crystals have been commonly prepared by cold drawing of a melt‐quenched film consisting of α‐form crystals. In this study, we have successfully produced highly oriented PVDF thin films (20 µm thick) with β‐crystals and a high crystallinity (55–76%), by solid‐state coextrusion of a gel film to eight times the original length at an established optimum extrusion temperature of 160°C, some 10°C below the melting temperature. The resultant drawn films had a highly oriented (orientation function f_c = 0.993) fibrous structure, showing high mechanical properties of an extensional elastic modulus of 8.3 GPa and tensile strength of 0.84 GPa, along the draw direction. Such highly oriented and crystalline films exhibited excellent ferroelectric and piezoelectric properties. The square hysteresis loop was significantly sharper than that of a conventional sample. The sharp switching transient yielded the remnant polarization P_r of 90 mC/m², and the electromechanical coupling factor k_t was 0.24 at room temperature. These values are about 1.5 times greater than those of a conventional β‐PVDF film. Thus, solid‐state coextrusion near the melting point was found to be a useful technique for the preparation of highly oriented and highly crystalline β‐PVDF films with superior mechanical and electrical properties. The morphology of the extrudate relevant to such properties is discussed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2549–2556, 1999     

Crystallization‐induced aging in poly(trimethylene terephthalate)/ poly(ethylene oxide terephthalate) segmented block copolymers

A new type poly(ether–ester) based on poly(trimethylene terephthalate) as rigid segments and poly(ethylene oxide terephthalate) as soft segments was synthesized and its aging behavior were investigated. Different from other polymer, the segmented block copolymers exhibited a unique aging mechanism. That is, the degradation of mechanical property within short term annealing was due to the overgrown crystals and dramatically increased crystallinity, which was proved by field emission scanning electron microscope (FE‐SEM) and differential scanning calorimetry (DSC), respectively. The deterioration in mechanical property after long term annealing was the results of both the increase in crystallinity and the decrease in molecular weight. Moreover, FE‐SEM showed many interesting flower‐like crystals presented on the surface of annealed sample. The flower‐like crystals consist of several radialized petal‐like arms and a more densely packed center, which has been seldom found in polymer bulk. Wide‐angle x‐ray diffraction results showed that the copolymer has the same crystal structure as PTT. Such poly(ether–ester) or its blends with other polymer could be suitable for rapid degradable products, such as package and vessel. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 411–416, 2010     

Extraordinary transport behavior of gases in isothermally annealed poly(4‐methyl‐1‐pentene) membranes

Poly(4‐methyl‐1‐pentene) (PMP) membranes were modified through isothermal annealing to investigate the change of their crystalline structure and rigid and mobile amorphous fractions (RAF and MAF), assuming a three‐phase model, affected the gas transport behavior. The crystalline structure was characterized by wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS) techniques, and the free volume properties were analyzed by positron annihilation lifetime spectroscopy. Compared with the pristine membrane, the annealed membranes show higher crystallinity; the crystals undergo partial structural change from form III to form I. The lamellar crystal thickness, rigid amorphous fraction thickness, and long period in the lamellar stacks increase with crystallinity. The annealed PMP membranes exhibit higher permeability due to the increase in larger size free volumes in MAF and higher selectivity due to the increase in smaller size free volumes in RAF, respectively. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2368–2376     

Crystallization improvement of poly(L‐lactide) induced by functionalized multiwalled carbon nanotubes

In the present work, the crystalline structures and the melting behaviors of poly(L ‐lactide) (PLLA) obtained after being annealed at different conditions have been investigated through differential scanning calorimetry and wide‐angle X‐ray diffraction, respectively. To improve the crystallization of PLLA, functionalized multiwalled carbon nanotubes (f‐MWCNTs) are introduced into PLLA. Our results show that by prolonging the annealing duration or enhancing the annealing temperature, the degree of crystallinity of PLLA gradually increases. Very important, the addition of f‐MWCNTs promotes the cold‐crystallization of PLLA dramatically even at relatively lower annealing temperature or in shorter annealing duration. Further results show that, whether in neat PLLA or in PLLA/f‐MWCNTs nanocomposite, only α form crystal forms during the annealing process. The glass transition temperature shifts to high temperatures because of the increase of crystallinity. F‐MWCNTs exhibit great heterogeneous nucleation effect for PLLA crystallization through enhancing the nucleation density, leading to homogeneous and tiny spherulites formation in a very short time. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 326–339, 2009