Pd/Pt二元合金电极的制备及氧还原性能

本文利用欠电位沉积亚单层的Cu及Pt置换取代Cu的方法, 制备了具有不同表面元素组成的Pd/Pt二元合金电极(用Pd/Ptx表示, x指欠电位沉积Cu-Pt置换取代Cu过程的次数),并对其表面元素组成、氧还原性能进行了表征. 在控制欠电位沉积Cu的下限电位恒定(0.34 V)的前提下, 表面Pt/Pd的元素组成比通过重复欠电位沉积Cu及Pt置换取代Cu的次数(1~5次)来可控地调变. 光电子能谱(XPS) 以及红外光谱实验表明,Pd/Ptx电极表层区的Pt：Pd元素组成比随着Pt沉积次数增加而增加, 对Pd/Pt4电极, 在电极表层区约2~3 nm内的Pt/Pd的原子比大约是1:4,而最表层裸露Pd原子的比例仍在20%以上。循环伏安结果显示, 随着Pt沉积次数的增加(1-5次), Pd/Ptx电极表面越不易被氧化。氧还原测试结果显示随着Pt沉积次数的增加(1~4次), Pd/Ptx二元金属电极的氧还原活性依次增加, 经过第3次沉积后其氧还原活性已优于纯Pt,而经4次以上沉积,其氧还原活性基本不变。在其它反应条件相同条件的前提下, Pd/Pt4电极上氧还原的半波电位与纯Pt相比右移约25 mV。结合本文与文献的实验结果,我们初步认为Pd/Ptx二元金属体系氧还原性能改善主要源自表层Pd原子导致其邻近的Pt原子上含氧物种吸附能的降低.     

次亚磷酸根离子在铂电极上氧化的机理研究(英文)

用SNIFTIRS和循环伏安法研究次亚磷酸根离子在多晶铂电极上的电氧化机理 .分析了0 .5mol/LH2 SO4 + 0 .1mol/LNaH2 PO2 溶液中原位红外反射谱图与Pt电极电位的关系 ,发现次亚磷酸根离子在Pt上发生解离吸附 ,其氧化产物是H3 PO4 ,不同于在Ni上的氧化产物H2 PO- 3 ,据此提出了酸性溶液中次亚磷酸根离子在Pt上氧化机理的新看法     

In situ electrodeposition of Pt nanoclusters on glassy carbon surface modified by monolayer choline film and their electrochemical applications

Pt nanoclusters attached to the monolayer choline (Ch) modified glassy carbon surface were successfully synthesized by use of in situ cyclic voltammetry (CV) method. Field emission scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and electrochemical impedance spectroscopy (EIS) were used to characterize the properties of this modified electrode. It was demonstrated that Ch was immobilized onto the carbon surface forming a covalently planted Ch monolayer, which could induce the formation of Pt nanoclusters. The preliminary study found that the homogeneous nanostructured Pt/Ch film exhibited remarkable electrocatalytic activity towards the oxidation of methanol and nitrite.     

Adsorption of anions on ultra-thin metal deposits on single-crystal electrodes: II: Voltammetric and radiochemical study of bisulfate adsorption on Pt(111) and Pt(poly) electrodes containing copper adatoms

The formation of ultra-thin metal deposits of copper on Pt(111) and polycrystalline platinum electrodes, as well as the adsorption of bisulfate on the copper-covered platinum surfaces, were studied by cyclic voltammetry and radioactive labeling. The highest charge obtained by voltammetry in the underpotential stripping range nearly corresponds to a close-packed monolayer of copper. The radioactive labeling data indicate that there are inactive and active copper adlayers toward bisulfate adsorption. The transition from inactive to active behavior is interpreted in terms of an increase in surface—bisulfate interactions at the expense of surface—perchlorate interactions. Based on recent X-ray absorption near-edge spectroscopy (XANES) analysis of copper deposition onto platinum, the site for bisulfate adsorption is most probably a Cu⁺ surface species. Combining this spectroscopic information with coulometry shows that an additional electron is confined to surface platinum atom(s) covered by the copper species. The copper film attains bulk copper properties when approximately 2.5 monolayers of copper are deposited.     

Model electrodes with defined mesoscopic structure

Model electrodes with defined mesoscopic structure were either generated by adsorption of surfactant stabilized metal clusters from colloidal solution on a support of gold or by electrochemical deposition of platinum on gold substrates. Both types of model electrodes were characterized by STM (scanning tunnelling microscopy), cyclic voltammetry and electrooxidation of adsorbed CO. The supported colloidal Pt as well as the electrochemically deposited Pt revealed different reactivities regarding the CO monolayer electrooxidation as compared to a polycrystalline Pt bulk electrode. In addition, in-situ FTIR (Fourier transformed infrared) spectroscopy was applied to characterize CO adsorbed on electrochemically deposited Pt on gold. Combined with the structural information from STM it seems likely that the differences regarding the catalytic properties of the model electrodes are due to different coverages of the substrate with catalyst particles. Received: 24 June 1996 / Revised: 29 November 1996 / Accepted: 4 December 1996     

Direct electrochemistry of Phanerochaete chrysosporium cellobiose dehydrogenase covalently attached onto gold nanoparticle modified solid gold electrodes

Achieving efficient electrochemical communication between redox enzymes and various electrode materials is one of the main challenges in bioelectrochemistry and is of great importance for developing electronic applications. Cellobiose dehydrogenase (CDH) is an extracellular flavocytochrome composed of a catalytic FAD containing dehydrogenase domain (DH(CDH)), a heme b containing cytochrome domain (CYT(CDH)), and a flexible linker region connecting the two domains. Efficient direct electron transfer (DET) of CDH from the basidiomycete Phanerochaete chrysosporium (PcCDH) covalently attached to mixed self-assembled monolayer (SAM) modified gold nanoparticle (AuNP) electrode is presented. The thiols used were as follows: 4-aminothiophenol (4-ATP), 4-mercaptobenzoic acid (4-MBA), 4-mercaptophenol (4-MP), 11-mercapto-1-undecanamine (MUNH(2)), 11-mercapto-1-undecanoic acid (MUCOOH), and 11-mercapto-1-undecanol (MUOH). A covalent linkage between PcCDH and 4-ATP or MUNH(2) in the mixed SAMs was formed using glutaraldehyde as cross-linker. The covalent immobilization and the surface coverage of PcCDH were confirmed with surface plasmon resonance (SPR). To improve current density, AuNPs were cast on the top of polycrystalline gold electrodes. For all the immobilized PcCDH modified AuNPs electrodes, cyclic voltammetry exhibited clear electrochemical responses of the CYT(CDH) with fast electron transfer (ET) rates in the absence of substrate (lactose), and the formal potential was evaluated to be +162 mV vs NHE at pH 4.50. The standard ET rate constant (k(s)) was estimated for the first time for CDH and was found to be 52.1, 59.8, 112, and 154 s(-1) for 4-ATP/4-MBA, 4-ATP/4-MP, MUNH(2)/MUCOOH, and MUNH(2)/MUOH modified electrodes, respectively. At all the mixed SAM modified AuNP electrodes, PcCDH showed DET only via the CYT(CDH). No DET communication between the DH(CDH) domain and the electrode was found. The current density for lactose oxidation was remarkably increased by introduction of the AuNPs. The 4-ATP/4-MBA modified AuNPs exhibited a current density up to 30 μA cm(-2), which is ～70 times higher than that obtained for a 4-ATP/4-MBA modified polycrystalline gold electrode. The results provide insight into fundamental electrochemical properties of CDH covalently immobilized on gold electrodes and promote further applications of CDHs for biosensors, biofuel cells, and bioelectrocatalysis.     

鲁米诺在铂电极上阳极电致化学发光的机理研究

研究了碱性鲁米诺溶液在多晶铂电极上的阳极电致化学发光(ECL)行为,观察到电极的预极化处理和溶解氧跟发光峰强度和峰形有直接关系。结合XPS谱图和Pt,Pt|S~a~d~s修饰电极的循环伏安特性,给出了鲁米诺阳极ECL两个发光通道的可能反应机理:(1)鲁米诺阴离子在表面有新鲜Pt原子的电极上氧化生成鲁米诺自由基,然后迅速与溶液中的氧反应形成0.22V(vs.Ag)处的发光肩峰;(2)电极表面的铂氧化物能加速原子态氧的发生过程,并增大0.60V(vs.Ag)附近ECL主峰的发光强度。     

丙三醇在Pt电极上吸附和氧化过程的原位FTIR反射光谱研究

运用电化学循环伏安(CV)和原位FTIR反射光谱方法, 研究了丙三醇在Pt电极上的氧化过程。结果指出, 丙三醇的氧化是一个复杂的表面过程。其间包括脱水、吸附、解离等步骤。根据CV和红外实验数据, 本文提出了Pt电极上丙三醇解离吸附的表面反应机理和不同电位下丙三醇氧化的分子过程。     

金属间化合物PtSb对乙醇的电催化氧化性能

采用氩弧熔炼和热处理方法获得PtSb有序金属间化合物材料. 用循环伏安和计时电流技术进行电化学性能测试. 在含有0. 25 mol•L^-1 CH₃CH₂OH的硫酸溶液中, 通过对乙醇电氧化的起始电位和电流密度大小的比较发现, PtSb金属间化合物具有良好的催化乙醇氧化性能. 利用XRD和XPS技术分析了晶体结构和电子结构. 采用不同扫描速率下的循环伏安技术得到乙醇氧化的电子交换系数(α), 发现C₂H_{5OH在PtSb催化剂表面上反应时的α远远大于在Pt电极表面的.}     

Adsorption and release behavior of bare and DNA-wrapped-carbon nanotubes on self-assembled monolayer surface

The adsorption and release behavior of single-stranded DNA-wrapped single-walled carbon nanotubes (ssDNA-w-SWCNTs) on alkylthiol self-assembled monolayer (SAM) surface was systematically characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Fast electron transfer between bare Au electrode and redox species blocked by the alkylthiol SAM can be restored by SWCNTs or ssDNA-w-SWCNTs. The release of ssDNA-w-SWCNTs is carried out by positive or negative desorption potential. SWCNTs/SAM or ssDNA-w-SWCNTs/SAM is completely removed from Au surface at +0.90 V or -1.40 V (vs. 3.0 M KCl|Ag|AgCl). The controlled release of SWCNTs/SAM and ssDNA-w-SWCNTs/SAM holds great promise for gene delivering.     

Direct Electrochemical Study of the Redox Species in RC Protein and its Mutants Immobilized in Self-Assembly Monolayers

4-Aminothiophenol (4-ATP) self-assembled monolayer (SAM) was immobilized on gold electrode. The multi-layered protein film electrode was prepared to rinse the 4-ATP-Au electrode in poly-styrenesulfonate (PSS) and poly-dimerthyldiallylammonium chloride (PDDA) successively, then soaked in a solution containing photosynthetic reaction center (RC) protein from Rhodobacter sphaeriodes or its pigment-replaced mutant. Thus, RC was found embedded in an ordered-orientation film. In cyclic voltammetry (CV) and square wave voltammetry (SWV), Au electrode gave a series of electrochemical signals due to the redox reaction of RC protein or its mutants. Intermolecular direct electron transfer (ET) was studied in this work.     

Investigation of Electrochemical Behavior of Some Dithiophosphonates in Acetonitrile on the Platinum and Gold Electrodes

Some dithiophosphonate derivatives were synthesized and the electrochemical reduction mechanism was investigated by cyclic voltammetry (CV), square wave voltammetry (SWV) and chronoamperometry (CA) in 0.1 M tetrabutylammoniumtetrafluoroborate (TBATFB) in acetonitrile at platinum (Pt) and gold (Au) electrodes. Dithiophosphonates showed a cyclic voltammetric reduction peak at about ?1.1 V at Pt and ?1.3 V at Au electrode (vs. Ag/Ag⁺) in this media. It was also shown that dithiophosphonates can be determined quantitatively in acetonitrile using a calibration graph. The number of electrons transferred were calculated as 2 using ferrocene as a reference compound at the UME electrode. Mechanism of dithiophosphonates was also examined on Pt and Au electrodes and electrochemical reduction of dithiophosphonates seems to follow an EC mechanism with an irreversible electron transfer step. The reaction product in the bulk electrolysis experiment was isolated and identified using proton‐coupled P‐31 NMR, ¹³C‐NMR and IR spectroscopy. The adsorption tests for dithiophosphonates were revealed that no strong or weak adsorption phenomena exist on both Pt and Au electrodes. Simulation curves were acquired by DigiSim 3.03 version to investigate the reduction mechanism and to estimate the kinetic parameters for electrochemical and chemical steps.     

Cysteamine monolayer inducing the formation of platinum nanoclusters for methanol electrocatalytic oxidation

Platinum nanoclusters (Pt-NCs) were synthesized on the surface of a gold electrode that was modified with cysteamine to form a kind of self-assembled monolayer via in-situ cyclic voltammetry (CV). Scanning electron microscopy, electrochemical impedance spectroscopy, and CV were used to characterize the properties of the electrode. The Cys monolayer induces the aggregation of platinum nanoparticles due to electrostatic interaction between the positive amino groups of the cystein monolayer and the negative charge of the hexachloroplatinate ions and causes the formation of Pt-NCs on the surface of the electrode. The resulting electrode exhibits high elecrocatalytic activity towards the oxidation of methanol.     

Direct electron transfer of hemoglobin founded on electron tunneling of CTAB monolayer

Direct electron transfer and stable adsorption of hemoglobin (Hb) on a carbon paste (CP) electrode were achieved with the aid of a single-chain cationic surfactant, namely, cetyltrimethylammonium bromide (CTAB). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) indicated that CTAB could form a complete monolayer with a high density of positive charges on the surface of the CP electrode, which strongly adsorbed negatively charged protein molecules via electrostatic interactions. The surfactant molecules anchored the protein molecules to align in suitable orientations and acted as electron-tunneling pathways between the protein molecules and the CP electrode. The bioelectrocatalytic activity of the immobilized Hb was confirmed by RAIR and UV-vis spectroscopies, and rapid electrochemical responses to the reduction of oxygen (O2), hydrogen peroxide (H2O2), and nitrite (NO2-) were also obtained.     

Voltammetry of basal plane platinum electrodes in acetonitrile electrolytes: effect of the presence of water

The first part of this report studies the electrochemical properties of single-crystal platinum electrodes in acetonitrile electrolytes by means of cyclic voltammetry. Potential difference infrared spectroscopy in conjunction with linear voltammetry was used to obtain a molecular-level picture of this interface. The second part of this report studies the hydrogen evolution and the hydrogen oxidation reactions on the three low-index faces of Pt electrodes in acetonitrile electrolytes. The data (CVs and IR spectra) strongly suggest that acetonitrile and CN(-) molecules are adsorbed on single-crystal platinum electrodes in the range of -1.5 to 0.3 V versus Ag/AgCl. Those species block part of the adsorption sites for hydrogen adatoms, and they decompose on the surface in the presence of water. The nature of the cation and the presence of water strongly affect the onset of acetonitrile electrolysis and the kinetics and stability of the adsorbed species on the electrode. Finally, the hydrogen evolution and the hydrogen oxidation reactions on platinum single-crystal surfaces in acetonitrile electrolytes are strongly affected by the surface-energy state of Pt electrodes.     

CO oxidation on Pt-modified Rh(111) electrodes.

The CO electro-oxidation reaction was studied on platinum-modified Rh(111) electrodes in 0.5 M H2SO4 using cyclic voltammetry and chronoamperometry. The Pt-Rh(111) electrodes were generated during voltammetric cycles at 50 mV s(-1) in a 30 microM H2PtCl6 and 0.5 M H2SO4 solution. Surfaces generated by n deposition cycles were investigated (Ptn-Rh(111) with n=2, 4, 6, 8, 10, and 16). The blank cyclic voltammograms of these surfaces are characterized by a pronounced sharpening of the hydrogen/(bi)sulfate adsorption/desorption peaks, typical for Rh(111), and the appearance of contributions between 0.1 and 0.4 V, which were ascribed to hydrogen/(bi)sulfate adsorption/desorption on the deposited platinum. At higher potentials, the surface oxidation of Rh(111) is enhanced by the presence of platinum. The structure of the Pt-modified electrodes was investigated by STM imaging. At low Pt coverages (Pt2-Rh(111)), monoatomically high islands are formed, which grow three dimensionally as the number of deposition cycles increases. After eight cycles, the monolayer islands have grown in diameter and range from mono- to multiatomic height. At even higher Pt coverage (Pt16-Rh(111)), the islands grow to particles of approx. 10 nm in diameter, which are 5-6 atoms high. The CO stripping voltammetry on these surfaces is characterized by two peaks: A low-potential, structure-insensitive peak, ascribed to CO reacting at the platinum monolayer islands, whose onset is shifted 150, 250, and 100 mV negatively with respect to pure Rh(111), Pt(111), and polycrystalline Pt, respectively, indicating the enhanced CO electro-oxidation properties of the Pt overlayer system. A peak at higher potentials displays strong structure sensitivity (particle-size effect) and was ascribed to CO reacting on the islands of multiatomic height. Current-time transients recorded on the surface with the highest amount of monolayer islands (Pt4-Rh(111)) also indicate enhanced CO-oxidation kinetics. Comparison of the Pt4-Rh(111) current-time transients recorded at 0.635, 0.675, and 0.750 V versus RHE (reversible hydrogen electrode) with those of pure Rh(111) and Pt(111) shows greatly reduced reaction times. A Cottrellian decay at long times indicates surface-diffusion-limited CO oxidation on the bare Rh(111) surface, while the peak visible at short times is indicative of CO reacting at the monolayer platinum islands. The results presented here show that, as indicated by density functional theory (DFT) calculations, the CO-adlayer oxidation for this system is enhanced compared to both pure Rh and Pt.     

铂铋金属间化合物催化剂的氧还原与抗甲醇氧化性能

采用氩弧熔炼后热处理方法制备了PtBi金属间化合物材料.采用循环伏安法和旋转圆盘电极进行电化学性能测试.通过在0.5 mol•L^－1 H₂SO₄＋0.25 mol•L^－1 CH₃OH溶液中对氧还原的起始电位和电流密度大小比较发现,与光滑铂电极相比,PtBi金属间化合物具有良好的氧还原催化性能和抗甲醇中毒性能.从结构方面分析了PtBi具有抗甲醇中毒性能的原因,认为是PtBi中Pt-Pt的间距大，不利于甲醇的吸附解离. X射线光电子能谱(XPS)结果表明,PtBi材料中Pt的d电子空穴增加,可能是导致PtBi电极表面氧还原电流增大的原因.     

Electrostatic attachment of gold and poly(lactic acid) nanoparticles onto omega-aminoalkanoic acid self-assembled monolayers on 316L stainless steel

The assembly of poly(lactic acid) (PLA) nanoparticles on a 12-aminodecanoic acid (ADA) self-assembled monolayer (SAM) is described. Assembly is accomplished through electrostatic interactions between the positively charged SAM and the negatively charged PLA nanoparticles. The strategy used involves two steps in which a preliminary electrochemical coating of the ADA SAM is followed by a second step that involves immersing the SAM in a solution containing gold or PLA nanoparticles. The SAM was characterized by using cyclic voltammetry (CV), X-ray photoelectron spectroscopy (XPS), FTIR spectroscopy, and contact angle measurements, whereas scanning electron microscopy (SEM) was used to image the nanoparticles after electrostatic attachment was achieved. We found that the surface coverage of the nanoparticles could be controlled by modulating the electrostatic interactions between the negatively charged particles and the positively charged SAM surface by varying the pH of the nanoparticle solution, the immersion time, and the number of cyclic voltammetry scans under which the SAM was formed.     

胆碱与谷氨酸共价单层混合修饰玻碳电极的制作与表征及其测定亚硝酸根的分析应用

A choline and L-glutamic acid mixed monolayer covalently modified glassy carbon electrode (Ch-Glu/GCE) was fabricated and characterized by X-ray photoelectron spectroscopy (XPS), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). It provided an excellent example of mixed covalent monolayer modification of carbon electrodes with alkanol and amino acid, and also a facile means for altering the interfacial architecture. The Ch-Glu/GCE displayed good catalytic activity toward the oxidation of nitrite anions. Differential pulse voltammetry was used for determination of nitrite at the Ch-Glu/GCE. The Ch-Glu/GCE showed higher capability for restraint of pollutions than a simple Ch modified electrode or a simple Glu modified electrode.     

Au@SiO2膜/Ti电极吸附吡啶的表面增强拉曼光谱研究

基于壳层隔绝纳米粒子增强拉曼光谱技术,合成了Au@SiO₂纳米粒子,并对其进行了相关表征. 结果表明,包裹的二氧化硅层连续、致密,Au@SiO₂膜/Ti电极上可获得金属钛电极上吸附吡啶分子的高质量表面增强拉曼光谱（SERS）信号. 通过Pt、Ni电极的测试,证实该信号源于吸附在基底表面的吡啶分子. 此外,Au@SiO₂膜/Ti电极上吸附吡啶分子的现场SERS光谱研究表明,在-0.1 V ~ -0.6 V电位区间,吡啶分子平躺吸附,从-0.6 V起吸附的吡啶分子由平躺逐转变为垂直,而当电位为-1.2 V时,电极表面析氢,吡啶脱附.