TiO2微图纹结构的制作

用软刻蚀技术中具有代表性的方法———微模塑法和转移微模塑法 ,在普通光学玻璃表面成功制备出TiO2 微阵列结构 .首先 ,以钛酸四丁酯为前驱物 ,通过溶胶 凝胶法合成出TiO2 溶胶 ,然后用表面带有微图纹的有机硅橡胶PDMS作为弹性印章分别对所制得的TiO2 溶胶进行微模塑及转移微模塑加工 ,在 70℃下溶胶凝胶 ,进而让凝胶材料在 5 5 0℃下焙烧 2h得到TiO2 微结构 .用光学显微镜对所得到的微结构进行了显微观察 ,显微照片显示 ,微模塑法和转移微模塑法在制备材料微结构方面复制精细度和重复率都比较令人满意 .同时 ,还初步探讨了影响最终图纹复制效果的凝胶温度、外加压力及模板等因素     

PCL/SiO2杂化纳米相微结构与晶态成核生长特性

应用扫描电子显微镜、广角X射线衍射和差示扫描量热手段研究了有机高分子/无机组分间以物理次价力(氢键)键合的高分子量PCL/SiO2杂化材料纳米相微结构和PCL高分子链在该微结构环境中的结晶成核生长特性及其影响因素.研究结果表明:杂化体系中高分子/无机组分间的微相分离尺度在纳米数量级,高分子微区的平均相畴尺寸在70nm左右,无机相形态呈现不规则的颗粒状.两相均匀分布程度与体系中组分间的氢键键合强度有关.PCL杂化后结晶度减小,对应的微晶尺寸明显改变,平衡熔点随无机组成含量的增加而下降.高分子链在晶核表面折叠形成结晶结构所需的能量增加.这一结果归因于无机非晶SiO2和键合强度的影响.     

有机-无机杂化低密度多孔材料的研制

主要开展了高内相乳液法（HIPE）制备有机／无机杂化低密度多孔材料。制备了不同SiO2含量的丙烯酸酯／SiO2杂化多孔材料，研究不同无机含量对杂化材料体积收缩的影响，结果列于表1。     

稀土/高分子杂化发光材料的研究

用SiO2为无机组份和以与SiO2具有相似折射率和优良力学性能的丙烯酸类如甲基丙烯酸甲酯（MMA）和甲基丙烯酸羟乙酯（HEMA），在交联剂3－（三甲氧基硅）丙基甲基丙烯酸酯（MSMA）存在下，快速制备了两种杂化基质材料SiO2/P(MMA-MSMA)和SiO2/P(HEMA-MSMA)。分别以盐酸和六次甲基四胺作为酸性催化剂和碱性催化剂，建立了快速制备透明凝胶的两步溶胶－凝胶法，大大缩短了溶胶的成胶时间，所得杂化材料具有良好的光学透明性，利用此方法制备了掺杂稀土配合物的多种发光杂化材料。采用组装的方法，得到了稀土配合物与层次化合物α－磷酸氢锆（α－ZrP)及中孔分子筛材料MCM－41的组装体，并对所制备的杂化材料进行了表征。另外，将稀土配合物通过共价键嫁接于无机SiO2基质中，得到了含有稀土配合物的分子杂化材料。     

PEG400对Eu(BA)3/SiO2发光性能的影响

稀土有机配合物进行无机化能提高热稳定性,但无机化基质对稀土有机配合物的荧光性影响较大,采用PEG3400对复合体进行改性,有利于改善荧光性.文章采用溶胶-凝胶法合成Eu(BA)3/SiO2和Eu(BA)3/PEG400-SiO2复合发光材料.研究了PEG400掺入量对SiO2中Eu(BA)3发光性能的影响,PEG400作为路易斯硬酸和稀土离子配体增强了Eu(BA)3的发光性能.用红外光谱说明PEG400的掺人有利于减少发光材料中的结晶水和羟基数目.通过原子力显微镜分析了PEG400的掺入量对SiO2基质结构的影响.     

担载ZnTHPP的TiO2杂化材料的制备及结构表征

采用溶胶-凝胶(Sol-gel)法将四(对-羟基)苯基锌卟啉(ZnTHPP)担载于TiO2机网络中,得到了一种新的有机/无机杂化材料.利用热重(TG)、红外光谱(FTIR)、紫外(UV)及固体漫反射光谱(DRS)、扫描电镜(SEM)对杂化材料的结构和形貌进行了表征,结果表明ZnTHPP/TiO2杂化材料具有良好的热稳定性,锌卟啉以化学键的形式与TiO2结合,并且锌卟啉的加入有效地拓宽了TiO2的可见光吸收范围.     

快速响应恢复的PI-SiO2/NiI2比色湿度传感器

有机-无机杂化型比色湿度传感器可通过电学信号和颜色变化获取环境湿度,并因其特征颜色区分度高、稳定性好、制备工艺简单等优点,在湿度监测领域具有广阔的应用前景,但其通常响应恢复时间长,从而不利于湿度实时监测.本文在聚酰亚胺(PI)-碘化镍(NiI₂)有机无机杂化材料中掺杂纳米SiO₂微球制备得到PI-SiO₂/NiI₂复合薄膜及比色湿度传感器,对其表面形貌和湿敏特性进行了研究.结果显示, PI-SiO₂/NiI₂薄膜具有蜂巢状的表面形貌,传感器的特征颜色显著,湿度响应时间小于1.5 s,恢复时间小于18 s.研究表明,纳米SiO₂微球掺杂能够较为显著地改善有机-无机杂化型比色湿度传感器的响应恢复特性,这对于传感器性能的提升具有一定参考意义.     

溶胶凝胶法制备PMMA/SiO2杂化材料

 针对目前PMMA/SiO₂杂化材料制备过程中容易出现的相分离问题，采用原位聚合和同步溶胶凝胶过程制备了聚合物链段与无机组分间有化学键作用的PMMA/SiO₂杂化材料，并应用透射电子显微镜、红外光谱分析仪、X射线衍射分析仪、热失重分析仪等对不同SiO₂含量的PMMA/SiO₂杂化材料的形貌及结构进行了研究。结果表明：SiO₂含量在20%～60%间的PMMA/SiO₂杂化体系没有明显的相分离现象，SiO₂含量在20%～40%间的杂化体系的透光性较好。     

键合型有机/无机杂化材料加载条形波导电光调制器

相对于普通的有机/无机杂化材料,侧链键合型有机/无机杂化材料能提高生色团的掺杂浓度,避免出现结晶、相分离等现象,同时生色团极化有序性的弛豫因生色团运动受阻而降低,具有较高的热稳定性.本文采用溶胶凝胶法合成了一种性能优良、稳定的侧链键合型有机/无机杂化材料,并将这种材料应用于电光调制器的电光层,利用传统的半导体工艺,采用...     

键合型有机/无机杂化材料加载条形波导电光调制器

相对于普通的有机/无机杂化材料,侧链键合型有机/无机杂化材料能提高生色团的掺杂浓度,避免出现结晶、相分离等现象,同时生色团极化有序性的弛豫因生色团运动受阻而降低,具有较高的热稳定性.本文采用溶胶凝胶法合成了一种性能优良、稳定的侧链键合型有机/无机杂化材料,并将这种材料应用于电光调制器的电光层,利用传统的半导体工艺,采用加载条形波导结构,成功制备了马赫-曾德尔(Mach-Zehnder,M-Z)型电光调制器.测试得到电光调制器在1 550 nm波长下10 kHz的响应信号,为键合型杂化材料应用于光电器件的进一步研究打下了基础.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.