长波段掺铒光纤放大器用掺铒光纤的设计考虑

本文分析了长波段掺铒光纤放大器(EDFA)的增益系数与Er³⁺离子浓度的关系.研制了铝共掺杂的高浓度掺铒光纤,以缩短长波段掺铒光纤的长度.用两级泵浦实现了L-波段EDFA.光纤放大器的掺铒光纤总长18m,在1570nm波长处的小信号增益为42.26dB,输出功率为17.5dBm.我们认为,较低的浓度淬灭效应归因于光纤中较高的A1掺杂浓度.当总的输入信号功率为-3dBm时,在1570至1600nm间的7路WDM信号的增益不平坦度仅为0.68dB..     

基于光纤环形激光器和光放大的100 km光纤布拉格光栅传感系统

在基于掺铒光纤-拉曼混合放大的可调光纤环形激光器的光纤布拉格光栅(FBG)传感系统结构基础上,提出了延长传感距离的新方法。该方法以环形掺铒光纤激光器作为光源,采用双波长拉曼放大的方法对信号进行低噪声的双向放大,系统中间的两段掺铒光纤再利用剩余的抽运功率产生自发辐射光和放大传感信号,使得整个系统能够在超长的传感距离上获得很高的信噪比。实验表明使用一只40 mW的掺铒光纤放大(EDFA)抽运源、一只170 mW的拉曼抽运源和一只2 W的拉曼抽运源,可以使整个系统的传感距离达到100km,并且传感系统的光纤布拉格光栅反射信号均能获得超过57 dB的优良信噪比,从而实现在超长距离上的光纤布拉格光栅传感。     

色散缓变掺铒光纤放大器的调制不稳定性

由于掺铒光纤放大器(EDFA)存在增益,相比于传输光纤它有较小的调制不稳定性阈值,使其很容易受到调制不稳定性的影响.本文将用微扰法分析基本的非线性薛定谔方程,研究色散缓变掺铒光纤放大器的调制不稳定性,分析其调制不稳定性积分增益谱与输入信号功率、放大器增益、放大器的长度、光纤纵向色散变化参量的关系.结果显示增大光纤纵向色散变化参量值是减小调制不稳定性对放大器影响的有效途径.通过分析调制不稳定增益产生长度,表明合理的选择放大器的长度可以消除调制不稳定性增益的产生.     

带光隔离器的掺铒光纤放大器性能分析

本文通过速率方程对带光隔离器的掺铒光纤放大器(EDFA)的性能进行了理论分析.由于光隔离器有效地抑制了反向传输的放大自发幅射(ASE),从而改善了掺铒光纤放大器的增益、噪音系数和输出功率等性能,分析结果表明光隔离器加在最佳位置时,可使小信号增益提高约5dB,噪音系数降低约1.6dB.     

WDM用增益平坦的高增益低噪声双段级联掺铒光纤放大器

给出了设计波分复用(WDM)用高增益、低噪声和宽带宽增益平坦的双段级联掺铒光纤放大器(EDFA)的一般步骤和方法.通过优化设计各种参量,研制出了一台高增益、低噪声和宽带宽增益平坦的双段级联EDFA样机,实现了从1524.8～1561.4 nm共36.6 nm带宽内±0.325 dB的平坦增益,0 dBm输入时,饱和输出功率大于15 dBm的高功率输出;噪声指数低于5 dB.     

掺铒光纤非线性耦合器的实验研究

提出一种耦合参量可用光调控的掺铒光纤非线性耦合器.用熔融拉锥法熔合两根掺铒光纤，拉制成工作波长为155nm的3dB掺铒光纤耦合器.通过调变输入耦合器一臂的980nm泵浦光功率，可以改变两臂的传播常量差，从而改变耦合器两臂信号光的相对输出功率.通过测量输入泵浦光功率和两臂信号光输出功率，得到直通臂耦合比依赖于泵浦光功率的实验曲线.实验研究表明，当泵浦光功率从0 mW变化至20 mW时，耦合比的变化可达到40％.与理论模拟的结果一致.     

两段级联掺铒光纤放大器的优化研究

基于Giles模型,研究了980 nm和1480 nm泵浦的两段级联掺铒光纤放大器(EDFA)的设计,得出了掺铒光纤(EDF)的最佳长度和光隔离器的最佳位置随泵浦功率和信号功率的变化关系.比较980 nm和1480 nm泵浦的两段级联EDFA,可以发现,前者的最佳EDF长度短,而光隔离器最佳位置距EDFA输入端远.     

掺铒光纤放大器中上转换过程的影响

掺杂浓度的提高影响了掺铒光纤放大器(EDFA)的性能,对经典Giles模型提出了新的要求。首先研究了高掺杂下铒离子距离较小引起的上转换过程的机理,通过优化速率方程模型分析了上转换过程对EDFA的影响,得出了在泵浦光和信号光远远大于ASE光的假设下泵浦光和信号光沿光纤长度变化的近似表达式,并将该近似分析解与解析解进行了比较。仿真结果表明上转换过程会降低随光纤传输的信号光和泵浦光,影响EDFA的放大性能,并得出了当掺铒浓度大于2.95×1025m-3时,上转换过程的影响不能忽略的结论。     

双向掺铒光纤放大器的特性分析

讨论了双向掺铒光纤放大器的结构方案,利用考虑放大的自发辐和北员耗影响的双向掺铒光纤放大器稳态放大速率方程模型分析的增益与掺铒光纤长度、输入信号光功率、帛运光功率及抽运方式等参数之间的关系,研究了单向和双向等功率抽运下正反向噪声系数随正反向信号光输入功率的变化行为。     

915nm泵浦混合掺铒/铒镱共掺双包层光纤放大器

研究了一种混合掺铒/铒镱共掺光纤放大器,用掺铒光纤放大器作为输入信号的预放大器,用铒镱共掺双包层光纤放大器作为主放大器。掺铒光纤放大器采用20m长掺铒光纤作为增益介质,采用最大输出功率318mW的单模半导体激光器二极管作为泵浦源,预放大器获得的最大输出功率是113mW。铒镱共掺光纤放大器采用14m长铒镱共掺双包层光纤作为增益介质,采用2个915nm多模半导体激光二极管作为泵浦源,在输入信号功率为10mW、信号波长1555nm时,混合光纤放大器获得了最大输出功率为32.04dBm,即1.6W,与此相应的混合光纤放大器的光-光转换效率为18.5%。     

Gain-clamping in two-stage L-band EDFA using an unwanted backward ase from second stage

A gain clamping technique for the long wavelength band erbium-doped fiber amplifier (L-band EDFA) is presented. It uses two circulators and a broad band fiber Bragg grating to route wasted backward C-band ASE from the second stage and launch it back into the input end of the first stage of a two-stage amplifier. The two-stage L-band EDFA has shown a small signal gain improvement of 5.7 dB compared to a single-stage amplifier with a slight noise figure degradation. By utilizing the wasted backward ASE, a L-band gain-clamped EDFA with high gain can be realized. Compared to the unclamped case, this gain-clamping technique is effective in reducing the total gain variation as small as 0.3 dB.     

掺铒光纤放大器在多路模拟光纤传输系统中应用

对应用掺铒光纤放大器的副载波频分复用模拟电视光纤传输系统的噪声和失真进行了实验研究，利用掺铒光纤放大器作为系统的功率提升和中继放大器，分别成功地进行了１８５ｋｍ和２１５ｋｍ的系统传输试验     

High gain double-pass L-band EDFA with dispersion compensation as feedback loop

We demonstrate an efficient double-pass L-band erbium-doped fiber amplifier (EDFA) incorporating chirped fiber Bragg grating (CFBG). The amplifier structure exploits the characteristics of CFBG to reflect the amplified signal back into the gain medium, filter out the recycled forward amplified spontaneous emission and block the residual 1480 nm pump power. The amplifier configuration has high gain and low noise figures as compared to double-pass EDFA using broadband mirror. The demonstrated amplifier has gain of more than 48 dB and low noise figure of less than 4 dB at low input signal power of −40 dBm.     

低噪声、高增益的L -band EDFA的实验研究

针对传统的L-band EDFA的工作效率低,提出了一种基于单根光纤光栅、泵浦分配、两段级联的EDFA的新结构,其中的光纤光栅用来反射无用的后向C-band ASE.系统地研究了泵浦比例和光纤光栅波长对增益噪声指数的影响关系.最后经实验验证,得到了低噪声、高增益的L-band的EDFA.其在输入信号光（1570 nm）功率为-30 dBm及泵浦功率为70 mW时,增益为22.26 dB,增益噪声指数为4.96 dB.     

掺铒光纤放大器的频率响应和瞬态增益

根据掺铒光纤放大器（ＥＤＦＡ）的速率方程和传播方程,忽略自发辐射噪声,推导出了小信号调制时频率响应函数的解析表达工以及大信号调制时描述瞬态增益的方程。数值计算表明,当输入信号的调制频率大于５ｋＨｚ时,放大器的瞬态增益变化很小,频率响应很弱。通过计算机仿真,描述了关闭一个信道时的放大器的增益变化过程。     

Effect of injection of C-band ASE on L-band erbium-doped fiber amplifier

The effect of injecting conventional band (C-band) amplified spontaneous emission on the performance of long-wavelength band erbium-doped fiber amplifier (L-band EDFA) is demonstrated. It uses a circulator and broadband fiber Bragg grating (FBG) to route C-band ASE from a C-band EDFA. Injection of a small amount of ASE (attenuation of 20 dB or above) improves the small signal gain with a negligible noise figure penalty compared to that of an amplifier without the ASE injection. A maximum gain improvement of 3.5 dB is obtained at an attenuation of 20 dB. At very large amounts of ASE injection (attenuation of 0 dB), the gain of the amplifier is clamped at 15.2 dB from ?40 to ?10 dBm with a gain variation of less than 0.3 dB. The saturation power is also increased from ?8 dBm (for without ASE injection) to 2 dBm (VOA=0 dB) with a slight noise figure penalty. These results show that the ASE injection technique can be used either for gain improvement or for gain clamping in L-band EDFA.     

Investigation of the optical gain and noise figure for multi-channel amplification in EDFA under optimized pump condition

We present the results of an investigation of optical gain and noise figure for simultaneous multi-channel amplification of an erbium doped fibre amplifier (EDFA) under optimized pump condition. Different pump configurations with varying input signal levels show interesting features on gain flatness. In the experiment, population inversion along the fibre length which determines the gain-spectra and noise characteristics of the amplifier is adjusted through optimized fibre length and injected pump power in order to minimize the gain-tilt at C-band. It is observed that bi-directional pumping manifests the best combination of low noise and high gain of EDFA which are useful as in-line repeaters in WDM network. We obtain 30 ± 1.5 dB intrinsically flat small signal gain from 1538 nm to 1558 nm band of wavelength with noise figure <4 dB for 16-channel simultaneous amplification in a single stage EDFA without gain flattening filter.     

光纤放大器增益饱和对有源光纤环形腔滤波特性的影响

从理论和实验两个方面研究了有源光纤环形腔滤波器输入光功率对光纤放大器增益的影响及由此引起的对有源光纤环形腔滤波特性的影响。在考虑上述影响的情况下 ,对有源光纤环形腔滤波器参数的优化作了讨论