钛金属表面结构可控多层钛酸盐纳米管薄膜的制备和结构稳定性

在水热条件下, 通过控制反应温度和氢氧化钠的浓度, 在钛金属表面得到结构可控的多层钛酸盐纳米管薄膜. 根据扫描电子显微镜和高倍透射电子显微镜的观测结果, 认为钛金属表面多层钛酸盐纳米管薄膜的形成经历以下4个阶段: (1) 钛金属的水合和碱性钛酸盐水凝胶的生成; (2) 碱性钛酸盐水凝胶分解并形成层状Na₂Ti₃O₇; (3) 层状Na₂Ti₃O₇的生长; (4) 层状Na₂Ti₃O₇的劈裂和多层卷曲成轴形成纳米管. 研究了薄膜形成后机械处理对薄膜形貌和结构稳定性的影响, 并利用超声的方法实现了多层膜的层分离.     

甲基纤维素(MC)疏水作用的电化学研究

应用电化学循环伏安法, 以电活性小分子亚甲基蓝(MB)为探针, 研究了不同温度下修饰在玻碳电极表面的甲基纤维素(MC)凝胶的疏水性. 研究发现, 在45～70 ℃温度范围内, MB在MC凝胶修饰电极上的式电位E⁰⁽较相应的裸电极均正移, 氧化峰电流i_pa和还原峰电流i_pc分别较相应裸电极增大, 且随温度升高而增大. 这些结果表明MC分子之间发生了疏水相互作用, 且随温度的升高, 疏水作用增强. 此外, 在上述温度下, MC凝胶修饰电极上峰电流的比值i_pc/i_pa均小于1, 为0.70, 且没有观察到MB单独的吸附峰, 因此MB分子在凝胶修饰电极上发生了弱吸附. 本文研究显示电化学方法是研究该类多糖凝胶机理的一个补充手段.     

基于互穿网络结构的pH/温度双重刺激响应性微凝胶的研究

室温下采用氧化-还原引发体系,以低交联密度的聚(N-异丙基丙烯酰胺)(PNIPAM)微凝胶为种子,通过种子乳液聚合法合成由PNIPAM和聚丙烯酸(PAA)形成的具有互穿聚合物网络结构的微凝胶.傅立叶变换红外光谱分析结果表明微凝胶由PNIPAM和PAA两种聚合物组成,透射电镜表征结果证实微凝胶中PNIPAM和PAA两种聚合物形成了互穿网络结构.用动态激光光散射测试不同温度或pH值水介质中微凝胶的粒径,结果发现微凝胶具有良好的pH/温度双重刺激响应性.在水介质pH值大于5.5的情况下,PAA组分对微凝胶的体积相转变温度没有影响;而在水介质pH值为4.0的情况下,由于PAA与PNIPAM之间的氢键作用,微凝胶的体积相转变温度稍微降低.微凝胶中PAA组分含量越高,其pH刺激响应性越显著.     

电解质对TiO2纳米管阵列膜光生阴极保护效应的影响

基于光电化学测试考察了光电解池中电解质(NaNO₃, NaCl, Na₂SO₄, Na₂S和NaOH)的种类和浓度对阳极氧化法制备的锐钛矿型TiO₂膜电极光电性能的影响, 并解释了其作用机理.结果表明, 电解质捕获空穴的能力顺序为Na₂S>NaOH>Na₂SO₄>NaCl>NaNO₃.Na₂S和NaOH在溶液中具有协同作用, 当两者组成混合溶液并且浓度均为0.5 mol/L时, 更有利于TiO₂膜光生电子-空穴对的分离和光电转化性能的提高.当0.5 mol/L NaCl溶液中的403不锈钢(403SS)与0.5 mol/L Na₂S+0.5 mol/L NaOH混合溶液中的TiO₂膜电极耦连时, 光照膜电极可使403SS的电极电位负移约650 mV, 具有良好的光生阴极保护效应.当切断光源时, 在该混合液中TiO₂膜也能对403SS起到一定的阴极保护作用.     

BeSO4-Al2(SO4)3-Na2SO4三元熔盐体系相图的研究

热分析法研究了BeSO₄-Al₂(SO₄)3-Na₂SO₄三元熔盐体系的状态图。体系中存在三元转熔(包晶)点P,温度490℃,组成为BeSO₄18.8Wt%,Al₂(SO₄)₃15.0%,Na₂SO₄66.2%;三元低共熔(共晶)点E₁,温度为476℃,组成为BeSO₄20.0%,Al₂(SO₄)₃11.2,%,Na₂SO₄68.8%。另一低共熔点E₂温度为595℃,组成未能确定。体系中无三元化合物生成。     

氧化石墨烯薄膜的光电化学性质

用改进的Hummers法制备了氧化石墨烯(GO), 在质子化的氧化铟-氧化硒导电玻璃基片上制备了静电自组装薄膜, 通过紫外-可见光谱和扫描电镜对薄膜进行了表征并研究了薄膜的光电化学性质. 结果表明, GO薄膜是一种稳定的光电阴极材料, 在光强为100 mW/cm²的白光照射下, 偏压为－0.4 V时, 0.1 mol•L^－1的Na₂SO₄溶液中薄膜电极的光电流密度达3.72 μA/cm².     

电沉积三维多孔Pt/SnO2薄膜及其对甲醇的电催化氧化

在高电流密度下以阴极析出的氢气泡为“模板”电沉积三维多孔Sn薄膜, 经在200 ℃ 2 h和400 ℃ 2 h热处理氧化后电沉积金属Pt, 制得三维多孔的Pt/SnO₂ (3D-Pt/SnO₂)薄膜. 通过扫描电镜(SEM)和X射线衍射(XRD)分析了薄膜的形貌和结构. 结果显示Pt主要沉积在SnO₂枝晶上, 形成Pt_shell/SnO_2core结构的枝晶. 在0.5 mol•dm^－3 H₂SO₄＋1.0 mol•dm^－3 CH₃OH溶液中的循环伏安结果表明, 3D-Pt/SnO₂薄膜电极在酸性溶液中电催化氧化甲醇的性能优于电沉积的纯铂电极, 而且具有较高的稳定性.     

温敏性纤维素/聚N-异丙基丙烯酰胺复合水凝胶的固体核磁共振表征及动力学研究

利用半互穿网络方法将具有温度响应的高分子聚N-异丙基丙烯酰胺(PNIPAM)与天然纤维素复合得到温敏性水凝胶. 通过固体核磁共振的 ¹H, ¹³C CP/MAS(交叉极化/魔角旋转)和QCP(定量交叉极化)等实验手段对复合凝胶的结构进行了定性及定量研究, 并利用固体静态变温核磁共振实验和偶极滤波-自旋扩散实验研究了复合凝胶中PNIPAM分子链段的动力学行为.     

高碱煤含钠矿物沉积层的高温熔融及多相反应过程分析

采用纯矿物试剂模拟燃用高碱煤时炉内受热面典型的灰沉积层化学组成,利用热机械分析（TMA）、TG-DSC分析、高温煅烧实验结合XRD、SEM-EDS表征方法研究了不同Na₂SO₄含量灰沉积层的高温熔融过程及矿物间的多相反应机理。结果表明,掺混Na₂SO₄后沉积层熔化特征温度显著降低,Na₂SO₄的主要反应途径与掺混比例有关,当掺混比低于20%时,Na₂SO₄与SiO₂、CaO、Al₂O₃反应主要转变为CaSO₄和钠的硅铝酸盐;掺混比大于40%时则主要与CaSO₄生成低熔点的钠钙复合硫酸盐。富Na₂SO₄沉积层颗粒在800℃时开始黏结;900-950℃时,霞石、钠长石等钠的硅铝酸盐发生低温共熔,同时Na₂SO₄和CaSO₄生成的复合硫酸盐开始熔融,逐渐形成液相;1200-1250℃时,镁黄长石与含钙矿物发生强烈共熔,温度超过1300℃后矿物完全熔融成为自由液相。     

均相催化剂催化氧气氧化生物质制备甲酸

甲酸是一种重要的化工原料,以可再生生物质为原料,通过催化氧气氧化制备甲酸具有重要意义。对于不溶于水的生物质原料的转化,采用可溶于水的均相催化剂体系证明是有效的。本文总结了均相催化剂体系(包括含钒杂多酸、含钒杂多酸+H₂SO₄、含钒杂多酸基离子液体、NaVO₃+H₂SO₄、VOSO₄、NaVO₃-FeCl₃+H₂SO₄、FeCl₃+H₂SO₄等)在催化氧气氧化生物质(包括生物质模型化合物、纤维素、木材、秸秆和玉米芯等)制备甲酸方面的研究,分析了其转化的过程和机理。最后,指出了目前催化氧化生物质制备甲酸存在的问题和挑战。     

燃烧与催化气化灰中铝溶出行为的研究

实验对比了燃烧灰与负载Na_2CO_3催化气化灰中Al的溶出行为,考察了Na_2CO_3负载量(0-15%,质量分数)和温度(600-1 000℃)对催化气化灰中主要矿物组成与Al溶出行为的影响。同时,采用XRD分析了燃烧灰、催化气化灰以及酸浸残渣的主要组成。结果表明,燃烧灰的主要组成为莫来石,而催化气化灰的主要组成为硅铝酸钠((Na_2O)_(0.33)NaAlSiO_4)。6 mol/L硫酸、60℃和30 min浸取条件下,燃烧灰的浸出率只有40%,而Na_2CO_3负载量为10%的催化气化灰的浸出率达到88%。催化气化灰更易于回收灰中的Al。     

The effect of CTAB on Na2SO4 nucleation in mixed Na2SO4/CTAB aerosols by FTIR-ATR technology

FTIR-ATR technology is used to study the efflorescence kinetic of Na_2SO_4 and mixed Na_2SO_4/CTAB aerosols.As the RH decreased linearly,the v_3-SO_4~2 band shifts from 1094 cm~1 to 1132 cm~1,suggesting the phase transition of Na_2SO_4 from solution to crystal phase(Ⅲ).For pure Na_2SO_4 aerosols,the ERH is 75.1%RH,whereas the efflorescence point of mixed Na_2SO_4/CTAB aerosols(74.2%) is lower.By further analysis of IR differential spectra,the ratio of Na_2SO_4 crystals in mixed aerosols is only 62.7%and the heterogeneous nucleation rate of Na_2SO_4 in Na_2SO_4/CTAB mixed aerosols is lower than that in pure Na_2SO_4 aerosols.They showed that CTAB assembled into reversed micelle and part Na_2SO_4 droplets are in the core to form core-shell structure,and CTAB shell prevents core Na_2SO_4 solutions from crystallizing.However,the counter ion Br for CTAB reversed micelle can interact with Na~+ ions,which decreases the crystallization rate of free Na_2SO_4 droplets and ERH is delayed.     

Modelling of calcium sulphate solubility in concentrated multi-component sulphate solutions

The chemistry of several calcium sulphate systems was successfully modelled in multi-component acid-containing sulphate solutions using the mixed solvent electrolyte (MSE) model for calculating the mean activity coefficients of the electrolyte species. The modelling involved the fitting of binary mean activity, heat capacity and solubility data, as well as ternary solubility data. The developed model was shown to accurately predict the solubility of calcium sulphate from 25 to 95 °C in simulated zinc sulphate processing solutions containing MgSO₄, MnSO₄, Fe₂(SO₄)₃, Na₂SO₄, (NH₄)₂SO₄ and H₂SO₄. The addition of H₂SO₄ results in a significant increase in the calcium sulphate solubility compared to that in water. By increasing the acid concentration, gypsum, which is a metastable phase above 40 °C, dehydrates to anhydrite, and the conversion results in a decrease in the solubility of calcium sulphate. In ZnSO₄–H₂SO₄ solutions, it was found that increasing MgSO₄, Na₂SO₄, Fe₂(SO₄)₃ and (NH₄)₂SO₄ concentrations do not have a pronounced effect on the solubility of calcium sulphate. From a practical perspective, the model is valuable tool for assessing calcium sulphate solubilities over abroad temperature range and for dilute to concentrated multi-component solutions.     

Determination of lead in seawater by inductively coupled plasma optical emission spectrometry after separation and pre-concentration with cocrystallized naphthalene alizarin

An analytical method for separation and pre-concentration of lead in seawater for determination by inductively coupled plasma optical emission spectrometry has been investigated. Lead was retained in the solid phase (0.5 g) composed of co-precipitated naphthalene and alizarin red. The solid phase quantitatively sorbs Pb(II) at pH 8–9, and the metal was eluted using 5.0 ml of 2 mol l⁻¹ nitric acid. The effect of NaCl, KCl, BaCl₂, CaCl₂, Na₂SO₄, MgCl₂ and Na₃PO₄ on the sorption of Pb(II) in the solid phase was studied. A set of solutions containing varying amounts of electrolytes (0.5; 1.0; 3.0 and 5.0% m/v) with Pb (50 μg) was prepared and the recommended procedure applied. The Na₃PO₄ was found to interfere; the other electrolytes did not interfere up to 5% m/v. A pre-concentration factor of 40 was obtained in this analytical procedure. The limit of detection and limit of quantification for Pb(II) were 53 and 176 μg l⁻¹, respectively. Lead was determined in seawater samples collected in Salvador city, Bahia, Brazil. The precision, expressed as R.S.D., was 1.8–4.6%, and the recovery of lead added to seawater samples was 95–97%.     

铂微粒修饰的氧化钛电极对甲醇的电催化氧化性能

直接甲醇质子交换膜燃料电池(DMPEMFC)可用作未来电动车辆的动力电源,但要达到实际应用还有大量问题有待进一步解决.目前限制DMPEMFC实际应用的主要问题是甲醇阳极氧化催化剂低的活性、高的价格及催化剂的毒化.     

Mechanism of Lithium and Cobalt Recovery from Spent Lithium-ion Batteries by Sulfation Roasting Process

Different from the traditional pyrometallurgical recovery process of Li and Co from spent lithium-ion batteries, a new recovery method for Li and Co was established by converting LiCoO₂ into water-soluble metal sulfates by roasting a mixture of LiCoO₂ and NaHSO₄·H₂O. The evolution law of the mixture with increased roasting temperature was investigated by thermogravimetry-differential scanning calorimetry(TG-DSC), in situ X-ray diffraction(XRD), XRD, and X-ray photoelectron spectroscopy(XPS). The results show that the phase transition of LiCoO₂ mixed with NaHSO₄·H₂O with increased temperature proceeded as follows:LiCoO₂, NaHSO₄·H₂O→LiCoO₂, NaHSO₄→Li_1-xCoO₂, LiNaSO₄, Na₂S₂O₇, Na₂SO₄→Li_1-xCoO₂, Co₃O₄, LiNaSO₄, Na₂SO₄→Co₃O₄, LiNaSO₄. The reaction mechanism of this roasting process may be as follows:LiCoO₂+NaHSO₄·H₂O→1/2Li₂SO₄+ 1/2Na₂SO₄+1/3Co₃O₄+1/12O₂+3/2H₂O, Li₂SO₄+Na₂SO₄=2LiNaSO₄.     

CO_2熔盐电化学转化碳材料的电化学特性

基于对熔融碳酸盐体系中电化学还原CO_2所得碳材料(electrolytic-carbon,EC)的形貌、结构、组成的认识,以粉末微电极循环伏安法测试为基础,在稀溶液中对EC的本征电化学行为进行了考察,以揭示这类碳材料的界面电化学特性。实验发现,在典型条件(450°C、4.5 V槽压)下制备的电解碳(450°C-4.5 V-EC)的伏安行为有别于多壁碳纳米管、石墨烯、石墨、乙炔黑等常见碳材料,在负电位区表现出显著的"双电层充放电响应迟滞"现象。通过考察溶液pH值、电位扫描速率、阴阳离子种类对这一现象的影响,发现pH和电解液组成都不影响这一现象的出现;电解液浓度提高和低扫描速率时滞后现象减弱,表明迟滞充放电是这类碳材料的本征特性,与其表面含氧官能团及其对阳离子的特性吸附密切相关。实验进一步研究了不同电解条件下制备的EC所展现的电化学特性吸附及电容性质,发现随着熔盐温度的升高,EC对电解液中阳离子的特性吸附能力降低,而相同温度不同槽压下制备的EC特性吸附能力相近,表现出相似的电容特性,这与EC的含氧量和比表面积有关。电解碳所展现的独特电容特性对其潜在的应用或可提供有价值的线索和指导。