Flow injection analysis using carbon film resistor electrodes for amperometric determination of ambroxol

Flow injection analysis (FIA) using a carbon film sensor for amperometric detection was explored for ambroxol analysis in pharmaceutical formulations. The specially designed flow cell designed in the lab generated sharp and reproducible current peaks, with a wide linear dynamic range from 5x10(-7) to 3.5x10(-4) mol L(-1), in 0.1 mol L(-1) sulfuric acid electrolyte, as well as high sensitivity, 0.110 Amol(-1) L cm(-2) at the optimized flow rate. A detection limit of 7.6x10(-8) mol L(-1) and a sampling frequency of 50 determinations per hour were achieved, employing injected volumes of 100 microL and a flow rate of 2.0 mL min(-1). The repeatability, expressed as R.S.D. for successive and alternated injections of 6.0x10(-6) and 6.0x10(-5) mol L(-1) ambroxol solutions, was 3.0 and 1.5%, respectively, without any noticeable memory effect between injections. The proposed method was applied to the analysis of ambroxol in pharmaceutical samples and the results obtained were compared with UV spectrophotometric and acid-base titrimetric methods. Good agreement between the results utilizing the three methods and the labeled values was achieved, corroborating the good performance of the proposed electrochemical methodology for ambroxol analysis.     

Simultaneous determination of ambroxol and salbutamol in human plasma by ultra‐performance liquid chromatography–tandem mass spectrometry and its application to a pharmacokinetic study

A rapid, selective and sensitive liquid chromatography–tandem mass spectrometry assay method was developed for simultaneous determination of ambroxol and salbutamol in human plasma using citalopram hydrobromide as internal standard (IS). The sample was alkalinized with ammonia water (33:67, v/v) and extracted by single liquid–liquid extraction with ethyl acetate. Separation was achieved on Waters Acquity UPLC BEH C₁₈ column using a gradient program at a flow rate of 0.2 mL/min. Detection was performed using electrospray ionization in positive ion multiple reaction monitoring mode by monitoring the ion transitions m/z 378.9 → 263.6 (ambroxol), m/z 240.2 → 147.7 (salbutamol) and m/z 325.0 → 261.7 (IS). The total analytical run time was relatively short (3 min). Calibration curves were linear in the concentration range of 0.5–100.0 ng/mL for ambroxol and 0.2–20.0 ng/mL for salbutamol, with intra‐ and inter‐run precision (relative standard deviation) <15% and accuracy (relative error) ranging from 97.7 to 112.1% for ambroxol and from 94.5 to 104.1% for salbutamol. The method was successfully applied in a clinical pharmacokinetic study of the compound ambroxol and salbutamol tablets.     

Rapid and sensitive liquid chromatography tandem mass spectrometry method for the quantification of ambroxol in human plasma

A sensitive, specific and rapid high-performance liquid chromatography-tandem mass spectrometry (LC-MS/MS) method was described and validated for the quantification of ambroxol in human plasma using enalaprilat as the internal standard (IS). Chromatographic separation was performed on a Lichrospher CN column with a mobile phase of methanol and water (containing 0.1% formic acid) (70:30, v/v). The total run time was 5.0 min for each sample. The analytes was detected by mass spectrometry with electrospray ionization source in positive selected reaction monitoring mode. The precursor-fragment ion reaction for ambroxol was m/z 378.9 --> 263.8, and for IS was m/z 349.0 --> 205.9. The linearity was established over the concentration range of 1.56-400.00 ng/mL. The inter-day and the intra-day precisions were all within 10%. A simple protein precipitation with methanol was adopted for sample preparation. The extraction recoveries of ambroxol and IS were higher than 90.80%. The validated method was successfully applied in pharmacokinetic study after oral administration of 90 mg ambroxol to 24 healthy volunteers.     

Automatic extraction-spectrophotometric method for the determination of ambroxol in pharmaceutical preparations

The spectrophotometric determination of trace amounts of ambroxol was carried out by liquid-liquid extraction using Bromothymol Blue with a flow-injection system. The determination of ambroxol in the range 8 x 10(-6)-4 x 10(-4) M was possible with a sampling frequency of 40 samples h(-1). The method was satisfactorily applied to the determination of ambroxol in pharmaceutical preparations.     

A simple flow injection spectrophotometric procedure for the determination of diazepam in pharmaceutical formulation.

A single-channel flow injection (FI) manifold with spectrophotometric detection has been designed and fabricated for diazepam determination. A 100 microl sample and/or standard solution containing diazepam was injected into a flowing stream of 0.1 mol L(-1) hydrochloric acid with the optimum flow rate of 6.8 mL min(-1). As soon as the sample reached the detector, the FI signal as a peak was recorded at 360 nm. The optimum conditions for microg amounts of diazepam were achieved. A linear calibration graph over the range of 2-110 mg L(-1) diazepam was obtained with the regression equation Y = 0.2926X + 0.5896 (r2 = 0.9929). The method was very sensitive, since as little as 0.60 mg L(-1) could be detected; very reproducible with an RSD of 3.3% (n=11); and very rapid with a sampling rate of 100 h(-1). The limit of quantitation (10 sigma) was 2.0 mg L(-1). The proposed FI procedure has been satisfactorily applied to the quantitation of diazepam in commercial pharmaceutical formulations. The obtained results were in excellent agreement with those obtained by the conventional spectrophotometric method, verified by the student t-test at the 95% confidence level.     

Mechanism of porous core electroosmotic pump flow injection system and its application to determination of chromium(VI) in waste-water

An electroosmotic pump flow injection system is introduced in this paper. According to electroosmotic theory, the pump's properties were described. A large flow range (mul min(-1)-ml min(-1)), moderate carrier pressure (>0.15 MPa), reduced performance voltage (<500 V) and stable flow rate (RSD<3.0% in 4 h) are the main properties of the pump. NH(4)OH (0.35 mM) was used as carrier for improving the pump's flow stability. The electroosmotic efficiency of the pump's medium, porous core, can be recovered and regenerated. A sandwich zone was used for sample and reagent introduction in order to adapt to the pump performance. Flow injection-spectrophotometry was employed for the determination of Cr(VI) in waste-water, based on the formation of the complex with 1,5-diphenylcarbazide and absorbance measurement at 540 nm. Within the calibration range of 0-7.0 mg l(-1) of Cr(VI), the RSD was 0.4% (n=5). The recovery of 0.70 mg l(-1) Cr(VI) added to the waste-water sample was 94.5+/-2.0% (n=5).     

Nickel and zinc determination by flow-injection solid-phase spectrophotometry exploiting different sorption rates

Flow-injection solid-phase spectrophotometry is applied for sequential determination of nickel and zinc, exploiting their different sorption rates on 1-(2-thiazolylazo)-2-naphthol (TAN) immobilized on C(18)-bonded silica. The Zn(II) sorption rate on the solid support is constant for flow rates ranging from 0.70 to 2.2 ml min(-1), but for Ni(II) the sorption rate decreases with increasing flow rate. A flow system was designed to perform sequential measurements at two different flow rates (0.85 and 1.9 ml min(-1)). The absorbance was measured at 595 nm, where both TAN-immobilized complexes showed maximum absorption. The coefficients of variation were estimated (n=10) as 1.1 and 1.7% (at 1.9 ml min(-1)) and 1.2 and 2.1% (at 0.85 ml min(-1)) for zinc and nickel, respectively. This strategy was applied to determine zinc and nickel in copper-based alloys and the results agreed with certified values at the 95% confidence level. The sample throughput was estimated as 36 h(-1).     

Sensitivity enhancement of chlorinated phenols by continuous flow liquid membrane extraction followed by capillary electrophoresis

This paper describes a new analytical system, based on the combination of continuous flow liquid membrane extraction (CFLME) enrichment and capillary electrophoresis (CE) separation, for analysis of chlorinated phenols in water samples. Five chlorinated phenols including 3-chlorophenol (3CP), 4-chlorophenol (4CP) 2,4-dichlorophenol (DCP), 2,4,6-trichlorophenol (TCP), and pentachlorophenol (PCP) were separated by CE with Tris/sodium dihydrogen phosphate solution containing methanol 1% (v/v) as the run buffer. CFLME related parameters were investigated and optimal enrichment was obtained by using 0.3 mol L(-1) Tris as acceptor and with a sample pH 5.0, a sample flow rate of 4.0 mL min(-1), and an enrichment sample volume of 150 mL. The detection limit (S/N= 3) was 6.9, 1.0, and 1.7 ng mL(-1) for DCP, PCP, and TCP, respectively. The reproducibility (RSD%, n = 6) was 5.7 for DCP, 2.5 for PCP, and 2.8% for TCP (n = 6). The proposed method was applied to the determination of chlorinated phenols in spiked water samples with relatively satisfactory recoveries.     

Determination of 0.1 to 1000 μ g/ml cadmium in a hydrometallurgical zinc refining process stream by a flow injection technique with computer controlled injection method

A computer-controlled flow injection system was developed for the determination of cadmium in a hydrometallurgical zinc refining process stream. An anion-exchange method in acidic potassium iodide medium was used for the on-line separation of cadmium from the matrix zinc. 1-(4-Nitrophenyl)-3-(4-phenylazophenyl)triazene (Cadion) was used as the chromogenic reagent for the spectrophotometric detection of cadmium. In order to expand the dynamic range of the flow injection - spectrophotometry, a computer-aided time-based variable-volume injection method has been employed for the introduction of the sample into the flow injection system. Samples ranging from 0.56 to 350 microl can be delivered by controlling the time period of the sample introduction valve and the flow rate of the carrier solution. The system permits a throughput of 5 samples per hour. The reproducibility has been proven to be satisfactory with a relative standard deviation of less than 6.2% (sample injected: 0.56 microl of 850 microg Cd/ml; n=100) and 5.0% (350 microl of 0.14 microg Cd/ml; n=5). The determination limit was 20 microg Cd/ml with 0.56 microl sample injection and 0.05 microg Cd/ml with 350 microl sample injection (the absolute amount of cadmium injected into the system was 11 ng and 17.5 ng, respectively).     

Potentiometric flow titration of iron(II) and chromium(VI) based on flow rate ratio of a titrant to a sample

A new potentiometric flow titration has been proposed based on the relationship of the flow rates between titrant and sample solutions. A sample solution is pumped at a constant flow rate. The flow rate of the titrant solution is gradually increased at regular time intervals and a flow rate for the titrant solution in the vicinity of the equivalence point is obtained. The concentration of the sample is calculated by C(S) (mol l(-1))=(R(T) (ml min(-1))xC(T) (mol l(-1)))/R(S) (ml min(-1)), where C(S), C(T), R(S), and R(T) denote the unknown sample concentration, titrant concentration in the reservoir, the flow rate of the sample solution which is a constant rate, and the flow rate of the titrant solution at an inflection point, respectively. The potentiometric flow titration of iron(II) with cerium(IV) and of chromium(VI) with iron(II) has been presented. The titration time of the proposed method is about 10 min per sample. An R.S.D. of the method is 0.77% for seven determinations of 1x10(-3) mol l(-1) iron(II). Similarly, the flow titration of chromium(VI) with iron(II) is carried out over the range 1x10(-4)-1x10(-3) mol l(-1) chromium(VI) and is successfully applied to the determination of chromium in high carbon ferrochromium.     

Determination of ambroxol hydrochloride in tablets using flow-injection UV spectrophotometry and HPLC

A flow-injection UV spectrophotometric method was developed for the determination of ambroxol hydrochloride in tablets. The quantitative determination of ambroxol was performed at 245 nm using distilled water as the carrier solvent. In this study, the flow rate, loop volume, and the number of injections per hour were 15 mL/min, 193 μL, and 100, respectively. The analytical signal of ambroxol was linear in the concentration range of 40–200 μg/mL. The detection limit and limit of quantification were found as 11.55 and 38.49 μg/mL, respectively. The results for the determination of ambroxol in tablets, 29.99 ± 0.23 mg (mean ± SD), were in good agreement with the labeled quantities (30 mg/tablet). A relatively high recovery value (100.4%) shows the accuracy of the proposed method. Furthermore, the results obtained were in accordance with those obtained by the HPLC method, which were used as a comparison method for the determination of ambroxol HCl, as far as the Student’s t-test and Fisher test results were concerned. It was concluded that the proposed flow-injection UV spectrophotometric method was fast, accurate, precise, and suitable for automation in the determination of ambroxol. The text was submitted by the authors in English.     

超高效液相色谱-串联质谱法测定人血浆中盐酸氨溴索及其制剂的生物等效性评价

采用超高效液相色谱-串联质谱（UHPLC-MS/MS）技术,建立了快速、简单、灵敏的测定人血浆中盐酸氨溴索含量的方法,并用于盐酸氨溴索人体生物等效性预试验研究。取50 μL血浆样品,采用蛋白沉淀法处理,以盐酸氨溴索-d5为内标。采用Waters XBridge BEH C18色谱柱（50 mm×2.1 mm,2.5 μm）,以0.1%（v/v）甲酸水-含0.1%（v/v）甲酸的甲醇为流动相,在0.4 mL/min流速下进行梯度洗脱。采用电喷雾电离（ESI）源以正离子模式进行MRM检测。结果显示,盐酸氨溴索在2~400 ng/mL范围内线性关系良好,相关系数（r）为0.998,准确度为97.1%~108.7%,精密度为1.0%~5.6%。将该方法用于6名健康受试者口服盐酸氨溴索受试制剂和参比制剂30 mg后血药浓度的测定,结果显示二者相对生物利用度为（102.3±14.8）%,血药浓度-时间曲线下面积（AUC_0-t、AUC_0-∞）和最大血药浓度（C_max）的90%置信区间均在80.0%~125.0%范围内,两种制剂生物等效。     

Flow-through micro sensor using immobilized peroxidase with chemiluminometric FIA system for determining hydrogen peroxide.

A micromachined flow cell (overall size; 25 x 25 x 1 mm3) was designed for the fast determination of hydrogen peroxide, based on a luminol-H2O2 chemiluminescence reaction catalyzed by immobilized peroxidase (POD). The flow cell consisted of a sandwich of anisotropically etched silicon and glass chips and contained a spiral channel (20 turns, 50 cm long, 150 microm wide, 20 microm depth, channel volume 1.4 microl) and two holes (1 mm diameter). POD was covalently immobilized with 3-(trimethoxysilyl)propyldietylenetriamine and glutaraldehyde on the inner surface of the channel. The chip was placed in front of a window of a photomultiplier tube and used as a flow cell in a single-line flow-injection analysis system using a luminol solution as a carrier solution. The sample volume for one measurement was 0.2 microl. The maximal sampling rate was 315 h(-1) at a carrier solution flow rate of 10 microl min(-1). A calibration graph for H2O2 was linear for 5 nM - 5 microM; the detection limit (signal-to-noise = 3) was 1 nM (7 fg in 0.2 microl injection). The H2O2 concentration in rainwater was determined using this sensor system.     

Sequential injection chromatographic determination of ambroxol hydrochloride and doxycycline in pharmaceutical preparations

A new separation method based on a novel reversed-phase sequential injection chromatography (SIC) technique was used for simultaneous determination of ambroxol hydrochloride and doxycycline in pharmaceutical preparations in this contribution.The coupling of short monolith with SIA system results in an implementation of separation step to until no-separation low-pressure method.A Chromolith^® Flash RP-18e, 25-4.6 mm column (Merck, Germany) and a FIAlab^® 3000 system (USA) with a six-port selection valve and 5 ml syringe were used for sequential injection chromatographic separations in our study. The mobile phase used was acetonitrile-water (20:90, v/v), pH 2.5 adjusted with 98% phosphoric acid, flow rate 0.48 ml min⁻¹, UV detection was at 213 nm.The validation parameters have shown good results: linearity of determination for both compounds including internal standard (ethylparaben) >0.999; repeatability of determination (R.S.D.) in the range 0.5-5.4% at three different concentration levels, detection limits in the range 0.5-2.0 μg ml⁻¹, and recovery from the pharmaceutical preparation in the range 99.3-99.9%. The chromatographic resolution between peak compounds was >5.0 and analysis time was <9 min under the optimal conditions. The method was found to be applicable for routine analysis of the active compounds ambroxol hydrochloride and doxycycline in various pharmaceutical preparations.     

Flow injection spectrophotometric determination of tetracycline in a pharmaceutical preparation by complexation with aluminium(III).

A rapid flow injection (FI) spectrophotometric procedure for tetracycline determination is described. It is based on the injection of a 100 microl sample solution containing tetracycline into merged streams of aluminium(III) chloride (0.01 mol 1(-1)) and Tris-buffer in the presence of KCl (0.06 mol l(-1)), pH 7.0, with the same optimum flow rate of 3.2 ml min(-1). A yellow Al(III)-tetracycline complex was monitored at 376 nm. The flow injection system and the experimental conditions were optimized by means of the univariate method. The procedure was applied to the determination of tetracycline in pharmaceutical preparations with a high sampling rate of at least 165 h(-1). A high precision with a relative standard deviation was obtained less than 0.72 and 0.30% of 5.0 and 10 microg ml(-1) (n=11), respectively. The detection limit (3sigma) and the quantification limit (10sigma) were 0.07 and 0.72 mg l(-1), respectively. There were no interference effects from traditional excipients in the dosage forms when the method was applied to pharmaceutical preparations. The matrix effect could be reduced by the standard addition method.     

Simultaneous on-line pre-concentration and determination of trace metals in environmental samples by flow injection combined with inductively coupled plasma mass spectrometry using silica gel modified with niobium(V) oxide

This work presents the development of an on-line pre-concentration system for simultaneous determination of Cd, Cu, Ni, V, Zn, Co and Pb in aqueous environmental samples and detection by inductively coupled plasma mass spectrometry. The system is based on cationic retention of the analytes onto a mini-column filled with silica gel modified with niobium(V) oxide. The effects of chemicals and flow variables have been investigated. The optimized operating conditions, selected as a compromise between sensitivity and analytical frequency were: sample pH 7.0, sample flow rate of 6.0mL min(-1), eluent flow rate of 2.0mL min(-1), and eluent (HNO(3)) concentration of 2.5mol L(-1). The relative standard deviation (n=7), enrichment factor and linear working range were 0.8-4.5%, 23.3-37.2 and 0.05-25.0microg L(-1), respectively. Limits of detection were between 0.01 and 0.03microg L(-1). The accuracy of the proposed method was checked with certified materials (NASS-4, NASS-5, CASS-4 and SRM 1643e). Values obtained were in accordance with those reported for the certified materials. Recovery was found to be in the range of 90-110% for a suit of water samples with variable matrices (seawater, tap water and ground water) collected in Florianopolis, Brazil.     

Powder dispensing robot for sample preparation

An automated powder dispensing station capable of transferring milligram quantities (1-100 mg) of powder for sample preparation was developed and integrated into a commercial robotic workstation (Zymark Prelude). The system's performance was optimized with respect to vacuum flow rate and powder transfer tube cross sectional area, and shown to possess excellent powder dispensing accuracy (RSD = < or = 0.1% for target weights < or = 15 mg) and precision (RSD = 3.43%) for a vanillin sample. Using the commercial features of the Zymark Prelude workstation (liquid handling, weighing, and vortexing/mixing) and the custom powder dispensing station, multiple sets of analytical calibration standards were prepared and subsequently analyzed by FIA in order to assess the system's robustness for sample preparation.     

Preconcentration and determination of trace metals in seawater using a thiol cotton fiber minicolumn coupled with inductively coupled plasma mass spectrometry.

A rapid separation and preconcentration method was developed for the determination of trace metals Cu, Zn, Cd, and Pb in seawater using a minicolumn packed with thiol cotton fiber (TCF) coupled with inductively coupled plasma mass spectrometry (ICP-MS). Preconcentration parameters, such as seawater sample volume and flow rate and eluent hydrochloric acid concentration, volume and flow rate, were optimized. Under the optimized conditions, trace metals Cu, Zn, Cd, and Pb in seawater can be determined with no interference from saline matrices. When a sample volume of 1500 ml and a sample flow rate of 15 ml min(-1) were used, the preconcentration factor of 1500 and RSD value of <7% at ng ml(-1) were achieved. The accuracy of the recommended method was verified by the analysis of certified reference materials.     

Determination of perfluorooctane sulfonate in river water by liquid chromatography/atmospheric pressure photoionization mass spectrometry by automated on-line extraction using turbulent flow chromatography

A simple, fast and sensitive liquid chromatography/atmospheric pressure photoionization mass spectrometry (LC/APPI-MS) method, with automated on-line extraction using turbulent flow chromatography (TFC), was developed for the determination of perfluorooctane sulfonate (PFOS) in river water. In this method, following an on-line extraction by injection onto a column under TFC conditions, PFOS is back-flushed onto a reversed-phase column via on-line column switching, and resolved chromatographically at a laminar flow rate of 1 mL min(-1). Using this tandem LC-LC/APPI-MS system the extraction, separation and selective detection of PFOS in river water could be achieved with satisfactory selectivity and sensitivity. The limit of detection (LOD) (S/N = 3) and the limit of quantitation (LOQ) (S/N = 10)were 5.35 and 17.86 pg mL(-1). The described procedure was very simple since no off-line sample preparation was required, total analysis time being 18.75 min.     

Development of an on-chip injector for microchip-based flow analyses using laminar flow

A new on-chip injector for microchip-based flow analyses has been designed and characterized. The microchip design utilizes separate laminar flow streams of buffer and sample that are brought into parallel contact for a distance of 300 microm. The buffer flow stream is first routed through a conventional 6-port injection valve fitted with a 5 microm i.d. sample loop. When the 6-port valve is actuated from load to inject for a given time, the on-chip buffer flow stream is constricted and the sample flow stream is pressurized into the buffer flow channel. Once the valve returns to the load state the separate laminar flow streams resume. Fluorescence detection was used to characterize the injector and it was found that 50 injections of a 100 microM fluorescein sample led to an average peak height of 174.32 +/- 2.05 AFU (RSD 1.18%) and average peak skew of 1.37 +/- 0.06. The injector was also interfaced with amperometric detection. Injections of catechol solutions ranging in concentration from 500 nM to 100 microM resulted in a linear response (sensitivity = 2.49 pA microM(-1), r(2) = 0.998) and a limit of detection of 155 nM (S/N = 3). Compared to an off-chip injection scheme, plug dilution, band broadening, and peak asymmetry are much reduced. Finally, the injection and subsequent lysis of an erythrocyte sample was demonstrated, with an injected plug of erythrocytes being lysed 5.72 +/- 0.15 s after injection into a flow stream containing sodium dodecyl sulfate (n = 10). The new injection scheme does not require complex valving mechanisms or high pressures and enables reproducible injections from a continuous sample flow stream in a manner where changes in analyte concentration can be monitored with high temporal resolution.