Potentiometric flow titration of iron(II) and chromium(VI) based on flow rate ratio of a titrant to a sample

A new potentiometric flow titration has been proposed based on the relationship of the flow rates between titrant and sample solutions. A sample solution is pumped at a constant flow rate. The flow rate of the titrant solution is gradually increased at regular time intervals and a flow rate for the titrant solution in the vicinity of the equivalence point is obtained. The concentration of the sample is calculated by C(S) (mol l(-1))=(R(T) (ml min(-1))xC(T) (mol l(-1)))/R(S) (ml min(-1)), where C(S), C(T), R(S), and R(T) denote the unknown sample concentration, titrant concentration in the reservoir, the flow rate of the sample solution which is a constant rate, and the flow rate of the titrant solution at an inflection point, respectively. The potentiometric flow titration of iron(II) with cerium(IV) and of chromium(VI) with iron(II) has been presented. The titration time of the proposed method is about 10 min per sample. An R.S.D. of the method is 0.77% for seven determinations of 1x10(-3) mol l(-1) iron(II). Similarly, the flow titration of chromium(VI) with iron(II) is carried out over the range 1x10(-4)-1x10(-3) mol l(-1) chromium(VI) and is successfully applied to the determination of chromium in high carbon ferrochromium.     

Sorptive behavior of Zn(II) on a lake sediment by sequential extraction-radiotracer technique

A sequential extraction-radiotracer technique was applied to a sediment core sample collected from lake Biwa (Japan) in order to evaluate relative importance of the fractionated solid components to sorb Zn(II) ions. The core was previously divided into three parts from the surface of the sediment; upper (0-6 cm), middle (6-12 cm) and bottom (12-18 cm). The solid residue after each chemical treatment was collected to perform a sorption experiment by using (65)Zn as a tracer. A difference in the amount of Zn(II) sorption was observed among original samples without any chemical treatments at each depth. The amounts were very small (10(-5) -10(-4) mol Zn(II) 100 g(-1) of dry sample) in all fractions of the sediment. Electrochemical measurements of cadmium and copper ion sorption supported the results from the radiometric sorption experiment. The effects of several potential factors on zinc sorption were investigated. Ion exchange of zinc with protons on the mineral surfaces was a significant cause of the zinc sorption.     

Synthesis, characterization and applications of pyrocatechol modified amberlite XAD-2 resin for preconcentration and determination of metal ions in water samples by flame atomic absorption spectrometry (FAAS)

A new chelating resin is prepared by coupling Amberlite XAD-2 with pyrocatechol through an azo spacer, characterized (by elemental analysis, IR and TGA) and studied for preconcentrating Cd(II), Co(II), Cu(II), Fe(III), Ni(II) and Zn(II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The sorption is quantitative in the pH range 3.0-6.5, whereas quantitative desorption occurs instantaneously with 2 M HCl or HNO(3) The sorption capacity has been found to be in the range 0.023-0.092 mmol g(-1) of resin. The loading half time (t(1/2)) is 1.4, 4.8, 1.6, 3.2, 2.3 and 1.8 min, respectively for Cd, Co, Cu, Fe, Ni and Zn. The tolerance limits of electrolytes NaCl, NaBr, NaNO(3), Na(2)SO(4) and Na(3)PO(4) in the sorption of all the six metal ions (0.2 mug ml(-1)) are reported. The Mg(II) and Ca(II) are tolerable with each of them (0.2 mug ml(-1)) up to a concentration level of 0.01-1.0 M. The enrichment factor has been found to be 200 except for Fe and Cu for which the values are 80 and 100, respectively. The lowest concentration of metal ion for quantitative recovery is 5, 10, 20, 25, 10 and 10 mug l(-1) for Cd, Co, Cu, Fe, Ni and Zn, respectively. The simultaneous determination of all these metal ions is possible and the method has been applied to determine all the six metal ions in tap and river water samples (RSD相似文献   

Quantitative separation of zinc traces from cadmium matrices by solid-phase extraction with polyurethane foam

A system for separation of zinc traces from large amounts of cadmium is proposed in this paper. It is based on the solid-phase extraction of the zinc in the form of thiocyanate complexes by the polyurethane foam. The following parameters were studied: effect of pH and of the thiocyanate concentration on the zinc extraction, shaking time required for quantitative extraction, amount of PU foam necessary for complete extraction, conditions for the separation of zinc from cadmium, influence of other cations and anions on the zinc sorption by PU foam, and required conditions for back extraction of zinc from the PU foam. The results show that zinc traces can be separated from large amounts of cadmium at pH 3.0±0.50, with the range of thiocyanate concentration from 0.15 to 0.20 mol l⁻¹, and the shaking time of 5 min. The back extraction of zinc can be done by shaking it with water for 10 min. Calcium, barium, strontium, magnesium, aluminum, nickel and iron(II) are efficiently separated. Iron(III), copper(II) and cobalt(II) are extracted simultaneously with zinc, but the iron reduction with ascorbic acid and the use of citrate to mask copper(II) and cobalt(II) increase the selectivity of the zinc extraction. The anions nitrate, chloride, sulfate, acetate, thiosulphate, tartarate, oxalate, fluoride, citrate, and carbonate do not affect the zinc extraction. Phosphate and EDTA must be absent. The method proposed was applied to determine zinc in cadmium salts using 4-(2-pyridylazo)-resorcinol (PAR) as a spectrophotometric reagent. The result achieved did not show significant difference in the accuracy and precision (95% confidence level) with those obtained by ICP–AES analysis.     

Equilibrium and kinetic properties of a fast iminodiacetate based chelating ion exchanger and its incorporation in a FIA-ICP-AES system

The equilibrium and kinetic properties of an iminodiacetate (IDA) based chelating ion exchanger with a crosslinked agarose, Novarose, as support has been investigated. The second and third acidity constants and some complexation constants of the ligand were determined for adsorbents with metal binding capacities of 140, 55 and 18 micromol ml(-1), respectively. The adsorbent of medium capacity showed fast adsorption and desorption of Cu(II), Cd(II), Ni(II) and Ca(II) both in the batch and column mode. It was found to be about 50 times faster than Chelex-100 (50-100 mesh) in accumulation of these metal ions in the batch mode. Studies of the adsorbent in a flow system, using a 5 mm x 6 mm i.d. column, indicated quantitative accumulation of Cu(II), Cd(II), and Ni(II) at volumetric flow rates up to 110 ml min(-1). Linear calibration curves with r > 0.999 and signal enhancement factors up to 1300 were obtained. Preconcentration by a FIA system connected to an ICP-AES instrument will make simultaneous measurement of ultratrace concentrations of a number of metal ions possible within reasonable cycle times due to the high flow rates which can be used with the adsorbent. Trace amounts of cadmium and copper in tap water were determined successfully at 60 ml min(-1). However, copper and nickel in tap water are strongly complexed and do not accumulate quantitatively even at low flow rates. Hence a sample pretreatment is needed. Copper was completely adsorbed after UV-treatment of the sample.     

Nickel determination in saline matrices by ICP-AES after sorption on Amberlite XAD-2 loaded with PAN

In the present paper, a solid phase extraction system for separation and preconcentration of nickel (ng g⁻¹) in saline matrices is proposed. It is based on the adsorption of nickel(II) ions onto an Amberlite XAD-2 resin loaded with 1-(2-pyridylazo)-2-naphthol (PAN) reagent. Parameters such as the pH effect on the nickel extraction, the effect of flow rate and sample volume on the extraction, the sorption capacity of the loaded resin, the nickel desorption from the resin and the analytical characteristics of the procedure were studied. The results demonstrate that nickel(II) ions, in the concentration range 0.10–275 μg l⁻¹, and pH 6.0–11.5, contained in a sample volume of 25–250 ml, can be extracted by using 1 g Amberlite XAD-2 resin loaded with PAN reagent. The adsorbed nickel was eluted from the resin by using 5 ml 1 M hydrochloric acid solution. The extractor system has a sorption capacity of 1.87 μmol nickel per g of Amberlite XAD-2 resin loaded with PAN. The precision of the method, evaluated as the R.S.D. obtained after analyzing a series of seven replicates, was 3.9% for nickel in a concentration of 0.20 μg ml⁻¹. The proposed procedure was used for nickel determination in alkaline salts of analytical grade and table salt, using an inductively coupled plasma atomic emission spectroscopy technique (ICP-AES). The standard addition technique was used and the recoveries obtained revealed that the proposed procedure shows good accuracy.     

Characterization of banana peel by scanning electron microscopy and FT-IR spectroscopy and its use for cadmium removal

This study describes the use of banana peel, a commonly produced fruit waste, for the removal of Cd(II) from environmental and industrial wastewater. The banana peel was characterized by FT-IR and scanning electron microscopy (SEM) coupled with energy dispersive X-ray (EDX) analysis. The parameters pH, contact time, initial metal ion concentration and temperature were investigated and found to be rapid ( approximately 97% within 10min). The Langmuir adsorption isotherm was used to describe partitioning behavior for the system at room temperature. The value of Q(L) was found to be (35.52mgg(-1)) higher than the previously reported materials. The binding of metal ions was found to be pH-dependent with the optimal sorption occurring at pH 8. The retained species were eluted with 5mL of 5x10(-3)M HNO(3) with the detection limit of 1.7x10(-3)mgL(-1). Kinetics of sorption followed the pseudo-first-order rate equation with the rate constant k, equal to 0.13+/-0.01min(-1). Thermodynamic parameters such as Gibbs free energy at 303K (-7.41+/-0.13kJmol(-1)) and enthalpy (40.56+/-2.34kJmol(-1)) indicated the spontaneous and endothermic nature of the sorption process. The developed method was utilized for the removal of Cd(II) ions from environmental and industrial wastewater samples using flame atomic absorption spectrophotometer (FAAS).     

Thiosalicylic acid-immobilized Amberlite XAD-2: metal sorption behaviour and applications in estimation of metal ions by flame atomic absorption spectrometry

Thiosalicylic acid (TSA)-modified Amberlite XAD-2 (AXAD-2) was synthesized by coupling TSA with the support matrix AXAD-2 through an azo spacer. The resulting chelating resin was characterized by elemental analyses, thermogravimetric analysis (TGA) and infrared spectra. The newly designed resin quantitatively sorbs CdII, CoII, CuII, FeIII, NiII and ZnII at pH 3.5-7.0 when the flow rate is maintained between 2 and 4 ml min-1. The HCl or HNO3 (2 mol l-1) instantaneously elutes all the metal ions. The sorption capacity is 197.5, 106.9, 214.0, 66.2, 309.9 and 47.4 mumol g-1 of the resin for cadmium, cobalt, copper, iron, nickel and zinc, respectively, whereas their preconcentration factor is between 180-400. The breakthrough volume of HCl or HNO3 for elution of these metal ions was found to be 4-8 ml. The limit of detection (LOD) for CdII, CoII, CuII, FeIII, NiII and ZnII was 0.48, 0.20, 4.05, 0.98, 1.28 and 3.94 micrograms l-1, respectively, and the limit of quantification (LOQ) was found to be 0.51, 0.29, 4.49, 1.43, 1.58 and 4.46 micrograms l-1, respectively. The loading half time, t1/2, for the cations was found to be less than 2.0 min, except for nickel for which the value was 13.1 min. The determination of each of these six cations is possible in the presence of other five, if their concentration is up to 4 times. All six metals were determined in river water (RSD approximately 0.7-7.7%) and tap water samples (RSD approximately 0.3-5.7%). The estimation of Co was made in the samples of multivitamin tablets (RSD < 2.3%). The results agree with those quoted by manufacturers.     

Continuous spectrophotometric determination of copper, nickel and zinc in copper-base alloys by flow-injection analysis

Flow-injection methods have been developed for the determination of copper, nickel and zinc in copper-base alloys, including several types of brasses, deoxidized copper, beryllium copper and German silver. The system for copper and nickel involves the measurement of the absorbance of the copper(II) and nickel(II) aquo-complexes at 805 and 410 nm, respectively, after simple dissolution of the sample in a nitric acid-phosphoric acid mixture. The system needs no further reagents and the sample solutions can be analysed at rates of up to 280 /hr for copper (or nickel in German silver) without any carry-over. The system for zinc consists of automatic dilution of the injected sample with a thiosulphate-acetate buffer solution and the subsequent measurement of the absorbance of the zinc-Xylenol Orange complex at 568 nm. This system permits analysis rates of up to 90/hr for zinc solutions, with no carry-over. The procedures have been applied to standard copper-base alloys. The results agreed satisfactorily with the certified values. The precision ranges are 0.2-0.7% for copper and nickel and 0.5-0.8% for zinc.     

Reversibility of cadmium sorption to calcite revisited

Cadmium sorption to calcite was studied in aqueous solution at calco-carbonic (CO(2)-H(2)O-CaCO(3)) equilibrium and at concentrations below the solubility product of otavite (<10(-7) mol L(-1)). Experiments were conducted in a stirred flow-through reactor, lasting for 15 and 60 h at flow rates of 1.6 and 0.5 mL min(-1), respectively. Under both flow conditions, the cadmium breakthrough curves reached steady state after a flow time of about 50 reactor volumes, but different calcite saturation levels were achieved, which implied time-dependent sorption rates. Desorption of cadmium was induced by switching from Cd-containing to Cd-free solution in the reactor inflow. Reversibility of sorption was then evaluated by comparing amounts sorbed and desorbed over identical time intervals. On average, the desorption/sorption ratio was 95±10%. Desorption rates were close to those for sorption and showed the same time dependency: Initially, rates were fast and slowed down with time. "Irreversible" surface reactions such as solid-solution formation could not be inferred. In previous research, cadmium sorption was often shown to be partly irreversible. We surmise that calcite surface ripening is conditioned by the concentration of lattice-building ions in the EDL. At calco-carbonic equilibrium, these ion concentrations at the surface are lowest. Therefore, irreversible binding of cadmium is not favoured.     

On-line preconcentration and determination of Zn in natural water samples employing a styrene-divinylbenzene functionalized resin and flame atomic absorption spectrometry.

In this work, flame atomic absorption spectrometry (FAAS) was used as a detector for the determination of zinc in natural water samples with a flow-injection system coupled to solid-phase extraction (SPE). In order to promote the on-line preconcentration of zinc from samples a minicolumn packed with 35 mg of a styrene-divinylbenzene resin functionalized with (S)-2-[hydroxy-bis(4-vinylphenyl)methyl]pyrrolidine-1-carboxylic acid ethyl esther was utilized. The system operation was based on Zn(II) ion retention at pH 9.5 +/- 0.5 in such a minicolumn with analyte elution, at the back flush mode, with 1 mol L(-1) HCl directly to the FAAS nebulizer. The influence of the chemical (sample pH, buffer concentration, HCl eluent concentration and effect of the ionic strength) and flow (sample and eluent flow rates and preconcentration time) parameters that could affect the performance of the system were investigated as well as the possible interferents. At the optimum conditions, for 2 min of preconcentration time (9.9 ml of sample volume), the developed methodology presented a detection limit of 1.1 microg L(-1), a RSD of 3.5% at 10 microg L(-1) and an analytical throughput of 24 h(-1). Whereas, for 4 min of the preconcentration time (19.8 ml of sample volume) a detection limit of 0.98 microg L(-1), a RSD of 6.5% at 5 microg L(-1) and a sampling frequency of 13 h(-1) are reported.     

Sorption characteristics of caffeine onto untreated polyurethane foam: application to its determination in human plasma

In the present paper, the sorption properties of caffeine (CAF) onto polyether type polyurethane foam (PUF) as solid phase sorbent were investigated with UV determination at 274.3 nm. Batch and column methods were used to optimize chemical, flow, kinetic and isothermal conditions for preconcentration of CAF. Results indicated quantitative sorption of CAF at pH 8 and 30 min shaking time. The maximum sorption capacity was found to be 4.1 mg g(-1). Column preconcentration was recommended at a flow rate of 1.5 mL min(-1) and desorption with 4 mL from 0.15 mol L(-1) hydrochloric acid. The procedure provided a linear analytical range of 0.05-30 mg L(-1). The detection and quantification limits are 0.016 and 0.047 mg L(-1), respectively. The procedure was applied to determination of CAF in spiked human plasma. The obtained recoveries were 98-101% and RSD values were from 0.05 to 9.5%.     

Preconcentration of lead with Amberlite XAD-2 and Amberlite XAD-7 based chelating resins for its determination by flame atomic absorption spectrometry

Four chelating matrices prepared by coupling Amberlite XAD-2 with chromotropic acid (AXAD-2-CA or 1), pyrocatechol (AXAD-2-PC or 2) and thiosalicylic acid (AXAD-2-TSA or 3) through azo spacer and impregnation of Amberlite XAD-7 with xylenol orange (AXAD-7-XO or 4) have been studied for enrichment of lead(II). All the four resins quantitatively sorb Pb(II) at pH 3.0-8.0 when the flow rate is maintained between 2 and 10 mlmin(-1). HNO(3) (0.5-4.0 M) instantaneously elutes Pb(II) from all the four chelating resins. The sorption capacity is in the range 16.0-186.0 mumolg(-1) and loading half time (t(1/2)) between 3.2 and 15.5 min. The tolerance limits of electrolytes (NaCl, NaBr, NaNO(3), Na(2)SO(4), Na(3)PO(4)) and cations (Ca and Mg) are reported. Phosphate interferes in the sorption with 3 and 4. The limit of detection and limit of quantification have been found to be in the ranges 2.44-7.87 and 2.76-8.64 ngml(-1), respectively. Lead has been determined in river (RSD approximately 2.6-12.8%) and tap (RSD approximately 1.8-7.2%) water samples.     

Reversed-phase porous silica rods, an alternative approach to high-performance liquid chromatographic separation using the sequential injection chromatography technique

A commercially available porous silica rod column was used as a separation tool for the sequential injection analysis (SIA). A porous solid monolithic column showed high performance at a low pressure, allowing sequential injection analysis to be used for the first time for separation in HPLC fashion. In this contribution, we tried to demonstrate a new separation concept with SIA manifold for the simultaneous determination of four different compounds (methylparaben (MP), propylparaben (PP), triamcinolone acetonide (TCA) and internal standard ketoprofen (KP)) in a pharmaceutical triamcinolon cream 0.1% formulation. A Chromolith Flash RP-18e, 25 mm x 4.6 mm column with a 10 mm pre-column (Merck, Germany) and a FIAlab 3000 system (USA) with an 8-port selection valve and 10 ml syringe were used for sequential injection chromatographic separations in our study. The mobile phase used was acetonitrile-methanol-water (35:5:65, v/v/v) + 0.05% nonylamine, pH 2.5, flow rate 0.6 ml min(-1). The analysis time was <6 min. A novel sequential injection chromatography (SIC) technique with UV spectrophotometric detection was optimised and validated.     

Sorption behavior of Zn(II) ions on synthesized hydroxyapatites

Calcium hydroxyapatite (CaHAP) and barium hydroxyapatite (BaHAP) have been prepared by a wet method from aqueous solutions with cation/P molar ratio of 1.67. The prepared particles were characterized using XRD, IR, TG-DTA and BET-N(2) adsorption measurements. The potential of the synthesized hydroxyapatites to remove Zn(II) from aqueous solutions was investigated in batch reactor under different experimental conditions. Both hydroxyapatites remove Zn(II) from aqueous solutions with an efficiency higher than 98% at initial pH around 6-8. The data reveal that the initial uptake was rapid and equilibrium was established in 20 and 60 min for CaHAP and BaHAP. The sorption process follows the pseudo-first-order kinetic with a rate constant (k(ads)) equals to 1.06x10(-2) and 1.91x10(-2) min(-1) for CaHAP and BaHAP, respectively. Zn(II) removal was quantitatively evaluated using Langmuir isotherm model and the monolayer sorption capacity (Q(max)) shows the values 102.04 and 36.62 mg g(-1) for CaHAP and BaHAP clarifying the high affinity of these novel sorbents for Zn(II) ions. Kinetically, the prepared apatites are feasible sorbents retain Zn(II) ions through a favorable and spontaneous sorption process. The possibility of metal recovery and regeneration of hydroxyapatites were investigated using several eluting agents include hydrochloric acids, double distilled water, calcium chloride, barium hydroxide, and copper chloride. Different desorption levels were obtained with the different adsorbents and the maximum recovery yield was achieved with copper chloride.     

Ion paired chromatography of iron (II,III), nickel (II) and copper (II) as their 4,7-Diphenyl-1,10-phenanthroline chelates

A reversed phase ion-paired chromatographic method that can be used to determine trace amounts of iron (II,III), nickel (II) and copper (II) was developed and applied to the determination of iron (II) and iron (III) levels in natural water. The separation of these metal ions as their 4,7-diphenyl-1,10-phenanthroline (bathophenanthroline) chelates on an Inertsil ODS column was investigated by using acetonitrile-water (80/20, v/v) containing 0.06 M perchloric acid as mobile phase and diode array spectrophotometric detection at 250-650 nm. Chromatographic parameters such as composition of mobile phase and concentration of perchloric acid in mobile phase were optimized. The calibration graphs of iron (II), nickel (II) and copper (II) ions were linear (r > 0.991) in the concentration range 0-0.5, 0-2.0 and 0-4.0 mug ml(-1), respectively. The detection limit of iron (II), nickel (II) and copper (II) were 2.67, 5.42 and 18.2 ng ml(-1) with relative standard deviation (n = 5) of 3.11, 5.81 and 7.16% at a concentration level of 10 ng ml(-1) for iron (II) and nickel (II) and 25 ng ml(-1) for copper (II), respectively. The proposed method was applied to the determination of iron(II) and iron(III) in tap water and sea water samples without any interference from other common metal ions.     

On-line preconcentration system using a minicolumn of polyurethane foam loaded with Me-BTABr for zinc determination by Flame Atomic Absorption Spectrometry

In the present paper, an on-line system for preconcentration and determination of zinc by Flame Atomic Absorption Spectrometry (FAAS) is proposed. It is based in the sorption of zinc(II) ions on a minicolumn packed with polyurethane foam loaded with 2-[2′-(6-methyl-benzothiazolylazo)]-4-bromophenol (Me-BTABr) reagent. Chemical and flow variables as pH effect, sample flow rate and eluent concentration were optimized using univariate methodology. The results demonstrated that zinc can determinate using the sample pH in the range of 6.5-9.2, sample flow rate of 6.0 ml min⁻¹, and the elution step using 0.10 mol l⁻¹ hydrochloric acid solution at flow rate of 5.5 ml min⁻¹. In these conditions, an enrichment factor of 23 and a sampling rate of 48 samples per hour were achieved. The detection limit (DL, 3σ) as IUPAC recommendation was 0.37 μg l⁻¹ and the precision (assessed as the relative standard deviation, R.S.D.) reached values of 5.9-1.8% in zinc solutions of 1.0-10.0 μg l⁻¹ concentration, respectively. The method was successfully applied to the determination of trace amounts of zinc in natural water samples from Salvador (Brazil).     

Potential of Modified Multiwalled Carbon Nanotubes with 1-(2-Pyridylazo)-2-naphtol as a New Solid Sorbent for the Preconcentration of Trace Amounts of Cobalt(II) Ion

The present paper reports on the application of modified multiwalled carbon nanotubes (MMWCNTs) as a new, easily prepared and stable solid sorbent for the preconcentration of trace Co(II) in aqueous solution. Multiwalled carbon nanotubes (MWCNTs) were oxidized with concentrated HNO(3) and modified with 1-(2-pyridylazo)-2-naphtol (PAN), and were then used as a solid phase for the preconcentration of Co(II). Factors influencing the sorption and desorption of Co(II) were investigated. Elution was carried out with 0.5 mol L(-1) HNO(3). The amount of eluted Co(II) was measured using flame atomic absorption spectrometry. The effects of the experimental parameters, including the sample pH, sample flow rate, eluent flow rate and eluent concentration, were investigated. The effect of coexisting ions showed no interference from most ions tested. The proposed method permitted a large enrichment factor (about 300). The precision of the method was 1.63% (for eight replicate determination of 0.5 microg mL(-1) of Co(II)) and the limit of detection was 0.55 ng mL(-1). The method was applied to the determination of Co(II) in water, biological and standard samples.     

Flow injection spectrophotometric determination of tetracycline in a pharmaceutical preparation by complexation with aluminium(III).

A rapid flow injection (FI) spectrophotometric procedure for tetracycline determination is described. It is based on the injection of a 100 microl sample solution containing tetracycline into merged streams of aluminium(III) chloride (0.01 mol 1(-1)) and Tris-buffer in the presence of KCl (0.06 mol l(-1)), pH 7.0, with the same optimum flow rate of 3.2 ml min(-1). A yellow Al(III)-tetracycline complex was monitored at 376 nm. The flow injection system and the experimental conditions were optimized by means of the univariate method. The procedure was applied to the determination of tetracycline in pharmaceutical preparations with a high sampling rate of at least 165 h(-1). A high precision with a relative standard deviation was obtained less than 0.72 and 0.30% of 5.0 and 10 microg ml(-1) (n=11), respectively. The detection limit (3sigma) and the quantification limit (10sigma) were 0.07 and 0.72 mg l(-1), respectively. There were no interference effects from traditional excipients in the dosage forms when the method was applied to pharmaceutical preparations. The matrix effect could be reduced by the standard addition method.     

A new functionalized resin and its application in preconcentration system with multivariate optimization for nickel determination in food samples

In this work, Amberlite XAD-2 resin functionalized with 4,5-dihydroxy-1,3-benzenedisulfonic acid was synthesized, characterized and applied as a new packing material for an on-line system to nickel preconcentration. The method is based on the sorption of Ni(II) ions in a minicolumn containing the synthesized resin, posterior desorption using an acid solution and measurement of the nickel by spectrophotometry (PAR method). The optimization of the system was performed using factorial design and Doehlert matrix considering five variables: eluent concentration, PAR solution pH, sample flow rate, PAR solution concentration and sample pH. Signals were measured as peak height by using an instrument software. Using the experimental conditions defined in the optimization, the method allowed nickel determination with achieved sampling rate of 25 samples per hour, detection limit (3 s) of 2 μg l⁻¹ and precision (assessed as the relative standard deviation) of 8.2-2.6%, for nickel solutions of 10.0-200.0 μg l⁻¹ concentration, respectively. The experimental enrichment factor of the proposed system was 46, for 120 s preconcentration time. The proposed procedure was applied for nickel determination in food samples. Recoveries of spike additions (5 or 10 μg g⁻¹) to food samples were quantitative (94-110%).