窄脉冲声用于大样品的吸声测量

本文利用逆滤波器原理,在空间产生了波形可控、长度在毫秒量级的窄脉冲声信号,分别采用脉冲分离法和脉冲叠加法,对一种毛毡材料和三种不同厚度的海绵材料进行了吸声系数的测量。实验证明,基于窄脉冲声信号的吸声测量结果与ISO13472-1:2002中的MLS脉冲法及阻抗管的测量结果基本吻合。采用窄脉冲进行吸声测量,可以减少样品边缘和周围环境对测量信号的干扰,提高现场测量的准确性。     

阻抗管内非标准尺寸样品的正入射吸声系数测量

针对尺寸显著小于阻抗管横截面的非标准尺寸样品,提出了一种阻抗管内非标准尺寸样品的正入射吸声系数测量方法,分析了其参数对测量结果的影响,并与标准尺寸样品(与阻抗管横截面相同)比较。首先在其旁布置一种具有特定声阻抗的同厚度的声学材料(PAM),形成与阻抗管横截面相同的表面平整的非连续阻抗试件(IAIS),然后根据GB/T 18696.2—2002测得IAIS表面声阻抗,并基于声电类比法计算得到非标准尺寸样品的表面声阻抗及其正入射吸声系数。结果表明,非标准尺寸样品的面积率越大或声扩散边界长度越小,该方法精度越高;当非标准尺寸样品为多孔材料时,选择非刚性的、声阻抗与之接近的PAM也可提高测量精度;而非标准尺寸样品为共振吸声结构时,选择刚性PAM时,本文方法仍具有一定精度。     

材料吸声系数双传声器测量的参数识别方法

本文提出了在普通房间中利用双传声器对多孔性和纤维性吸声材料吸声系数测量时的参数识别方法。利用Delany&Bazley经验模型对测量数据进行了参数识别,建立了材料的阻抗模型,并计算出材料全频带的吸声系数。与驻波管方法得到的吸声系数相比,在0～3000Hz范围内,二者都能较好地吻合。通过在不同的环境中进行对比测试,说明该方法具有较好的重复性和准确性。     

基于声压-质点速度声强探头的材料吸声系数的测量

通过由一个声压换能器和一个质点速度换能器所构成的传感器(p-u声强探头)同时测量材料表面附近的声压和质点振动速度,可直接得到其声学阻抗,进而得到材料的反射因子、吸声系数。本文利用一个p-u探头声强测量系统,在半消声室内测量了三聚氰胺泡沫的吸声系数,分析了声源高度和入射角度、材料样本尺寸和厚度对吸声系数测量的影响,并和阻抗管中测量得到的法向吸声系数进行了对比。最后分析了声阻抗率的幅值和相位误差对吸声系数的影响,推导了它们的误差传递公式。     

高声压级时多孔金属板的吸声特性研究

针对高声压级下有限厚度多孔金属板在线性阻抗背衬条件下(背衬表面声压与声质点速度为线性关系)的吸声问题,提出了一个描述不同声压级下材料层法向吸声性能的一维模型,并给出求解材料层内部声质点速度的线化与差分方法,以预测多孔金属板在高声压级下的非线性吸声特性。在阻抗管中对两块多孔金属板进行了声学测试,得到了材料层法向表面阻抗和吸声系数随入射声压级变化的实验结果。研究表明:实验与理论预测符合良好,验证了模型与数值方法的正确性。本文所提原理和方法,可用于一般硬质多孔材料。      

基于声场重建的材料吸声系数测量方法

针对现有方法对材料吸声系数进行现场测量时存在低频测量误差大的问题,本文提出了一种利用扬声器线阵列对材料吸声系数进行现场测量的新方法。该方法使用基于能量比值约束的最小二乘法在待测材料表面进行平面波声场重建并结合双传声器传递函数法对材料的吸声系数进行测量。数值仿真表明在100～1600 Hz频率范围内,新方法在未加约束时能够对材料的吸声系数进行准确测量。在半消声室中利用新方法测量了三聚氰胺泡沫的吸声系数,分析了能量比值约束值对测量结果的影响,并和阻抗管以及其它两种现场测量方法的测量结果进行了对比。结果表明该方法能够对吸声材料在160～1600 Hz频段内的吸声系数进行准确测量,并且相较于现存的现场测量方法,新方法具有更低的测量频率下限。     

黏弹性材料的动态力学特性及其对覆盖层吸声性能的影响

本文利用标准化动态力学测量手段获得了某种高分子聚合物的动态杨氏模量,并根据时温等效原理对动态杨氏模量与声学测量在频段上的差异加以分析和转换,得到了500—7500 Hz频率范围内该黏弹性材料杨氏模量随频率变化的特性.基于所测得动态杨氏模量,采用有限元方法分析了均匀黏弹材料的吸声性能,并将仿真结果与样品声管实验数据进行对比,验证了测试所得参数的准确性.进一步仿真分析了含有局域共振结构的声学覆盖层吸声性能,并讨论了黏弹性材料的动态特性对其吸声性能的影响,提出了改进水声覆盖层低频宽带吸声特性的建议.     

使用脉冲声和矢量传声器的现场测量吸声系数

使用不同声源利用矢量传声器对毛毡材料进行现场吸声系数测试,研究了不同背景下不同声源的抗噪能力。矢量传声器可以同时测得声压和质点振速信号,进而可计算得到阻抗,利用自由空间和材料表面的阻抗可计算得到材料的吸声系数。在此次实验中,使用不同声源分别在无干扰和有一白噪声干扰源的两种情况下进行测试。结果表明,使用对数扫频脉冲和巴特沃斯脉冲测试所得的吸声系数曲线更平滑,说明脉冲声可以有效降低环境反射的影响,在高噪声背景下使用对数扫频脉冲测试所得的结果基本没有受到背景噪声的影响,说明对数扫频脉冲的抗噪能力更强。因此,使用对数扫频脉冲作为声源进行测试可有效减弱环境反射和背景噪声的影响。     

声学二维平面周期结构的吸声性能建模

声学周期结构兼具优化室内声场环境,节约建筑吸声材料的特性而在现代建筑中广泛使用。针对二维平面周期结构的声场优化特性,建立了一种吸声系数计算模型。首先,根据边界条件理论推导了吸声系数的线性方程组,继而通过数值分析方法进行求解,最后在驻波管和混响室中分别进行实验验证。实验结果表明,测量的吸声系数和理论计算曲线吻合良好,该模型可以准确测算二维平面周期结构的吸声系数。同时分析表明:在平面周期结构中,相同吸声材料面积情况下,吸声材料占比越大,吸声效果越好;在相同吸声材料面积和占比情况下,材料边缘长度越长,高频段吸声效果越好;随着材料边缘长度的减少,边缘效应影响减弱。      

管束穿孔板的管腔耦合共振吸声机理研究

为了揭示管束穿孔板共振吸声结构的吸声机理,利用热黏性条件下基于有限元算法的管束穿孔板仿真模型,研究了平面声波正入射条件下,管束穿孔板内部声场分布特征,并利用阻抗管对吸声系数的理论仿真结果进行了试验验证.结果表明,管束穿孔板在低频主要靠腔体共振吸声,在高频主要靠管共振吸声,管束穿孔板整体呈现出较为明显的管腔耦合共振吸声特征。管束穿孔板共振时管中声强和质点法向振速较大,高频次吸声峰频点处管中和腔中均有驻波形成,频率越高驻波数量越多.管束穿孔板的耦合共振受到管长、腔深、穿孔率和管内径等参数变化的影响,管长对高频耦合共振的影响最大,管长增大使高频主吸声峰频点移向低频,并使相邻主吸声峰之间的间距减小.      

A model comparison of the absorption coefficient of a Microperforated Insertion Unit in the frequency and time domains

The absorption coefficient of acoustic materials can be measured either in the frequency or the time domain. At normal incidence, a sample of the material is fitted within an impedance tube and the absorption coefficient is calculated in the frequency domain from the measurement of the transfer function between two microphones [ISO 10534-2. Acoustics - determination of sound absorption coefficient and impedance in impedance tubes - Part 2: transfer function method. ISO, Geneva, Switzerland; 1996]. When the acoustic material must be characterized at oblique incidence or in situ (noise barriers, for instance) the absorption coefficient is calculated from measurements of the loudspeaker-microphone impulse response in the time domain, both in free field and in front of the sample [CEN/TS 1793-5. Road traffic noise reduction devices - test method for determining the acoustic performance - Part 5: intrinsic characteristics - in situ values of sound reflection and airborne sound insulation. CEN, Brussels, Belgium; 2003, ISO 13472-1. Acoustic measurement of sound absorption properties of road surfaces in situ - Part I: extended surface method. ISO, Geneva, Switzerland; 2002]. Since the absorption is an intrinsic property of the acoustic material, its measurement in either domain must provide the same result. However, this has not been formally demonstrated yet. The aim of this paper is to carry out a comparison between the absorption coefficient predicted by the impedance model of a Microperforated Insertion Unit and the absorption coefficient predicted from a simulated reflection trace taken into account the finite length of the time window.     

Measurement of sound absorption by underwater acoustic material using pulse-separation method

An alternative pulse-separation method is presented for measuring the sound absorption at normal incidence of an underwater acoustic material in a water-filled impedance tube. A damped sine pulse was generated in the water-filled impedance tube with a regular waveform and a short duration time of approximately 1 ms. During the generation of the pulse, the inverse filter principle was used to compensate for the transducer response. In addition, the effects of the characteristics of the tube termination can be eliminated during the generation of the pulse to obtain a single plane pulse wave in the impedance tube, which is a necessary condition for this technique. Measurements of the sound absorption coefficient of the rubber material and the reflection coefficient from a water/air interface were used to verify the pulse-separation method.     

Evaluation of the acoustic and non-acoustic properties of sound absorbing materials using a three-microphone impedance tube

This paper presents a straightforward application of an indirect method based on a three-microphone impedance tube setup to determine the non-acoustic properties of a sound absorbing porous material. First, a three-microphone impedance tube technique is used to measure some acoustic properties of the material (i.e., sound absorption coefficient, sound transmission loss, effective density and effective bulk modulus) regarded here as an equivalent fluid. Second, an indirect characterization allows one to extract its non-acoustic properties (i.e., static airflow resistivity, tortuosity, viscous and thermal characteristic lengths) from the measured effective properties and the material open porosity. The procedure is applied to four different sound absorbing materials and results of the characterization are compared with existing direct and inverse methods. Predictions of the acoustic behavior using an equivalent fluid model and the found non-acoustic properties are in good agreement with impedance tube measurements.     

基于低频吸声超构材料的复合消声器研究*

针对管道内低频噪声难以抑制的问题，本文基于亥姆霍兹共振腔（HR）阵列吸声板和穿孔管消声器组合，设计了一种复合式宽带消声器。首先利用有限元法仿真分析传统穿孔管消声器，发现中低频消声能力较差，通过嵌入HR阵列吸声板吸收中低频噪声。采用仿真与实验的方式研究吸声板的声学性能：在400-1000 Hz频段内的平均吸声系数达到了0.88。然后对复合式消声器进行数值模拟及3D打印阻抗管实验测试对比：复合式消声器在400-1718Hz频率范围内的平均传递损失为18.15 dB ，最终实现了管道内全频带噪声有效控制。     

Utilizing vector hydrophones to achieve an active anechoic terminal in an acoustic tube

A new integrated active sound absorptive terminal using vector hydrophones is developed for the anechoic terminal of impedance tube,with which the reflected and the incident waves can be separated.The method overcomes the limitations imposed by the sensor spacing and measuring frequency range in the traditional two-hydrophone method,and can effectively expand low-frequency sound absorption band of the terminal.The effect of hydrophone sensitivity on the sound absorptive performance of the terminal is evaluated,a correction method is also provided for the reflection and transmission coefficient.The experimental results show that the absorption coefficient in the frequency band of 0.1-2 kHz is over 0.98,which agrees well with the theoretical results.     

水下弹性微穿孔吸声结构吸声系数研究

利用模态叠加法建立了水介质微穿孔板的数学模型,基于声电类比法得到其等效电路模型。研究了弹性微穿孔板和弹性背腔对垂直入射吸声系数的影响。与空气介质中的微穿孔板不同,水下微穿孔板因结构阻抗不足,难以取得满意的吸声效果,为此提出了增强型微穿孔吸声结构,并在水介质阻抗管内对理论结果予以验证。结果表明,随着增强型弹性微穿孔板弯曲刚度的增大,其在[20,2000]Hz范围内的平均吸声系数得到提高,逐步趋近于刚性微穿孔板的结果,弹性背板使微穿孔吸声结构的吸声峰向低频移动,低频吸声效果得到提高。      

Application of the ISO 13472-1 in situ technique for measuring the acoustic absorption coefficient of grass and artificial turf surfaces

This paper presents the applicability of an in situ technique based on ISO 13472-1 standard for measuring the acoustic absorption coefficient of grass and artificial turf surfaces for normal incidence from a sound source. The in situ method is based on acoustic impulse response measurement of the material surface. A maximum length sequence (MLS) signal is played through a loudspeaker and the acoustic response from the surface is recorded using a single microphone. The fast Hadamard transform and fast Fourier transform based digital signal post-processing algorithm provides the acoustic absorption coefficient of the surface under test. The normal incidence acoustic absorption coefficient of a commercial artificial quash surface of Dow Co. obtained from this method was compared with the results from the ASTM E1050 impedance tube method for the same surface. The acoustic absorption coefficients of a test-site grass surfaces were measured for 30 mm and 100 mm length of grass blades in wet and dry soil conditions. Substantial difference in the acoustic absorption coefficient was observed for a similar grass-like artificial surface used for estimating sound power of commercial garden equipments and lawnmowers. The advantage of the in situ method lies in its ability to measure the normal incident acoustic absorption coefficient of any planar surface as installed or in situ. Additionally a quick testing time of less than a minute with the use of a laptop sound card based inexpensive data acquisition system is the main feature of this robust method.