沉积工艺参数对碳纳米管薄膜场发射性能的影响

利用微波等离子体化学气相沉积(MWPCVD)方法,在不锈钢衬底上直接沉积碳纳米管膜。通过SEM、拉曼光谱和XRD表征,讨论了制备温度和甲烷浓度对碳纳米管膜场发射的影响。结果表明:不同条件下制备的碳纳米管膜的场发射性能有很大差异,保持氢气的流量(100sccm)、生长时间(10min)、反应室压力不变,当甲烷流量为8sccm、温度为700~800℃时,场发射性能最好,开启场强仅为0.8V/μm,发射点分布密集、均匀。     

生长温度对碳纳米管阴极场发射性能的影响

碳纳米管(Carbon Nanotubes,CNTs)场发射平面显示器(Field Emission Display,FED)与其他显示器比较显示了其独特优点,被认为是未来理想的平面显示器之一。碳纳米管阴极作为器件的核心部分,其性能的好坏直接影响显示器的性能。针对30~60英寸(76.2~152.4cm)大屏幕显示器所用的厚膜工艺,即采用丝网印刷法制备了碳纳米管阴极阵列,研究了化学气相沉积法在不同温度下生长的CNTs的场发射电流-电压特性,找到了适合FED用碳纳米管的最佳生长温度。结果表明生长温度越高(750℃),CNTs场发射性能越好。并用荧光粉阳极测试这些CNTs的场发射发光显示效果,验证了上述结论。     

LPCVD法制备碳纳米管薄膜及其场发射性能的研究

采用低压化学气相沉积法(LPCVD)在镍片上直接制备碳纳米管(CNTs)薄膜,系统地研究了生长温度(500~800℃)对碳纳米管薄膜形貌、结构及场发射性能的影响,并对此方法的生长机理进行了分析。当温度从500℃升高到650℃时,碳纳米管的生长速率随着温度升高而增大,而温度继续上升,速率则明显减小。利用扫描电镜(SEM)和拉曼光谱仪表征和检测了碳纳米管薄膜的形貌和结构。碳纳米管的管径、长度、一致性和晶化程度随温度都有明显的变化。同时还对碳纳米管薄膜的场发射特性进行了测试,对其场发射机理进行了深入地探讨,表明温度对碳纳米管的性能有很大影响,并存在最优化的温度条件。实验结果表明碳纳米管薄膜的形貌、结构及其场发射性能可通过生长温度进行一定范围的控制。     

薄膜光学 制膜技术与装置

O484.12006054416LPCVD法制备碳纳米管薄膜及其场发射性能的研究=Deposition of carbon nanotubes fil mby LPCVDand relatedfield emission property[刊,中]/陈婷(华东师范大学纳米功能材料和器件应用研究中心.上海(200062)),孙卓…//光学学报.—2006,26(5).—777-782采用低压化学汽相沉积法(LPCVD)在镍片上直接制备碳纳米管(CNTs)薄膜,系统地研究了生长温度(500~800℃)对碳纳米管薄膜形貌、结构及场发射性能的影响,并对此方法的生长机理进行了分析。当温度从500℃升高到650℃时,碳纳米管的生长速率随着温度升高而增大,而温度继续…     

类富勒烯纳米晶CNx薄膜及其场致电子发射特性

利用微波等离子体增强化学气相沉积技术制备出了CNx薄膜,并利用x射线光电子能谱、x射线衍射、扫描电子显微镜和Raman光谱等测试手段对所制备的CNx薄膜的微结构和成分进行了分析.研究了其场致电子发射特性.发现薄膜的结构和场发射特性与反应系中的甲烷、氮气及氢气的流量比有关,当甲烷、氢气及氮气流量比为8/50/50sccm时,制备的薄膜具有弯曲层状的纳米石墨晶体结构(类富勒烯结构)和很好的场发射特性.场发射阈值电场降低至1.1V/μm.当电场为5.9V/μm时,平均电流密度达70μA/cm2,发射点密度大于1×104cm-2.     

乙醇做碳源Mo-Co/MgO做催化剂合成单壁碳纳米管

本文采用柠檬酸法制备Mo-Co/MgO催化剂, 在小型流化床中, 以Ar气为载气直接携带乙醇蒸汽进入反应器, 通过化学气相沉积（CCVD）技术来合成制备单壁碳纳米管（SWCNTs）。利用扫描电镜和拉曼光谱方法研究了催化剂组分比例和载气流量等对SWCNTs制备的影响。研究结果表明: 以乙醇做碳源, Mo1-Co10/MgO做催化剂, Ar气流量为150sccm时制备的单壁碳纳米管质量最佳。     

催化剂对纳米非晶碳膜场发射性能的影响

利用微波等离子体增强化学气相沉积(MPECVD)法,在经处理的单晶硅衬底上沉积了纳米非晶碳薄膜.通过Raman、SEM、XRD表征,研究了催化剂对纳米非晶碳膜的生长速率及场发射性能的影响.结果表明,在制备纳米非晶碳膜时使用FeC13,作为催化剂可大幅提高其生长速率.在相同的制备条件下,与未加FeCl3催化剂制备的纳米非...     

类富勒烯纳米晶CNx薄膜及其场致电子发射特性

利用微波等离子体增强化学气相沉积技术制备出了CN_x薄膜,并利用x射线光电子能谱、x射线衍射、扫描电子显微镜和Raman光谱等测试手段对所制备的CN_x薄膜的微结构和成分进行了分析.研究了其场致电子发射特性.发现薄膜的结构和场发射特性与反应系中的甲烷、氮气及氢气的流量比有关,当甲烷、氢气及氮气流量比为8/50/50 sccm时,制备的薄膜具有弯曲层状的纳米石墨晶体结构（类富勒烯结构）和很好的场发射特性.场发射阈值电场降低至1.1V/μm.当电场为5.9V/μm时,平 关键词： 类富勒烯 x薄膜')" href="#">CN_x薄膜 场致电子发射 微波等离子体增强化学气相沉积     

碳纳米管/硅纳米孔柱阵列的场发射性能

"通过热化学气相沉积的方法将碳纳米管生长到硅纳米孔柱阵列衬底上．采用场发射扫描电子显微镜、透射电子显微镜、高分辨透射电子显微镜、拉曼光谱和X射线能谱对所制备的样品形貌、组成进行了分析．结果发现：所制备产物为一种具有面积大、准周期性的碳纳米管/硅巢状阵列复合结构．能谱分析表明碳纳米管仅含有碳元素．对样品进行场发射性能测试表明该结构开启电压为1.3 MV/m,当外加电压为4.26 MV/m,发射电流为5 mA/cm2．由FN公式计算相应的场增强因子约为1.1￡104．碳纳米管/硅纳米孔柱阵列好的场发射性能被归     

碳纳米管制备条件探索及对亚甲基蓝的吸附性能

探索了用气相沉积法制备碳纳米管时,不同温度、催化剂浓度、反应时间对碳纳米管定向性、径向管径、表面性能的影响,结果表明,反应温度750℃、催化剂浓度5g/100mL、反应时间30min是制备碳纳米管的最佳实验条件。在最佳条件下制备碳纳米管并进行对亚甲基蓝吸附的研究,探索了吸附时间、pH、吸附浓度、温度对吸附结果的影响。     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.