苯甲醛肟与炔丙醇偶极环加成反应的理论研究

用密度泛函理论(DFT)方法在B3LYP/6-31G*水平上研究了苯甲醛肟与炔丙醇加成反应的微观机制和热力学、动力学行为. 结果表明, 在苯甲醛肟与炔丙醇加成反应过程中, 8个可能反应通道的过渡态中均形成非平面五元环结构, 其中苯甲醛肟的Z、E构型特征得到了部分保留, 但主要部分的键长、键角均发生了变化, 电荷也进行了重新分布. 苯甲醛肟以羟基型参与反应的4个反应通道均为吸热反应和热力学非自发过程, 它们均具有较高的反应势垒、较慢的反应速率和较小的平衡常数; 而以离子型参与反应的四个反应通道均为放热反应和热力学自发过程, 它们的反应势垒较低, 反应速度较快, 平衡常数也较大, 故苯甲醛肟应主要以离子型参与反应. 炔丙醇的两种取向对应着加成反应的两种产物, 反应达到平衡后, 3-羟甲基二氢异噁唑为主要产物.     

Kinetics of Phase Transfer Catalytic Preparation of Benzyl Phenyl Ether

Benzyl phenyl ether is prepared in a well-stirred batch reactor from phenol and benzyl chloride using tetrabutylammonium iodide as phase transfer catalyst. Phenol with sodium hydroxide is dissolved in water as the aqueous phase, and benzyl chloride is dissolved in toluene as the organic phase. Tetrabutylammonium iodide gives high reaction rate without the formation of micelles during the reaction. The reaction mechanism is verified by infrared spectrum study and other experimental observations. The kinetics of the reaction of benzyl chloride is modelled as a first-order chemical reaction. The cocatalytic effect of the iodide ion, and salting out effect on the overall reaction rate are discussed in detail using experimental data.     

芴的9位羟甲基化反应产物的影响因素

以聚甲醛为羟甲基化试剂,研究了碱的种类、反应温度和反应时间等因素对芴与聚甲醛发生羟甲基化反应产物类型的影响。 结果表明,提高碱的强度有利于生成9,9-双羟甲基芴,升高温度和延长反应时间则有利于生成9,9′-亚甲基双芴。 通过控制反应条件,有可能优先生成9-芴甲醇或9,9-双羟甲基芴或联产这2个化合物。     

反应类等键反应方法及类反应热动力学参数计算

本文提出了反应类等键反应方法,将通常用于热力学性质计算的等键反应方法推广用于类反应中反应势垒和反应焓变的计算. 对碳氢燃料低温燃烧反应机理中的一类重要反应类：?烷基自由基过氧化氢裂解生成烯烃和HO2自由基的反应势垒和反应焓变进行了计算. 通过对该类16个反应中的5个代表反应分别在不同计算水平HF、DFT、MP2、CCSD(T)的比较计算发现,采用等键反应方法可在较低从头算级别计算得到类反应较高精度的反应势垒,提高了计算的效率和精度. 本文采用反应类等键反应方法在B3LYP/6-311G(d,p)计算水平对该类16个反应进行了反应势垒和反应焓变的计算,并建立了反应势垒和反应能的线性自由能关系：delta V=71.02+0.41?delta E.     

The use of polymer-bound triphenylphosphine in the stereochemical inversion of secondary alcohols

Polymer-bound triphenylphosphine can replace triphenylphosphine in the Mitsunobu reaction to generate stereochemically inverted secondary alcohols. This method is comparable with the standard Mitsunobu reaction in terms of inversion of stereochemistry, yield, and reaction time, even for sterically very hindered secondary alcohols. The special merit of this reaction is that the excess polymer-bound triphenylphosphine and its by-products are easily removed by filtration from the reaction products.     

Kinetics of phenol oxidation with ozone in a thin layer on a solid surface

Ozone has been reacted with phenol in thin supported layers, and the dynamics of this reaction has been investigated. The stoichiometry of this reaction coincides with the stoichiometry of the same reaction in solution. Specific reaction rate (β) has been determined for various phenol conversions. The effective rate constant of the reaction, estimated by extrapolating β to zero reaction time, is significantly higher than the rate constant of the reaction in solution. The reaction between ozone and phenol is diffusion-controlled. The reaction products form a barrier layer, which protects the deeper phenol layers against ozone. The barrier layer is as thick as 8–15 phenol monolayers.     

Chemoselective Schmidt reaction mediated by triflic acid: selective synthesis of nitriles from aldehydes

An excellent utility of Schmidt reaction of aldehydes to access corresponding nitriles in an instantaneous reaction is demonstrated. The reaction of aldehydes with NaN(3) and TfOH furnishes the corresponding nitriles in near quantitative yields and tolerates a variety of electron-withdrawing and electron-donating substituents on the substrates. Formanilides, a common side product in Schmidt reaction, is not observed in this reaction. Besides these advantages, the salient feature of this reaction is that it exhibits a remarkable chemoselectivity, as acid and ketone functionalities are well tolerated under the reaction conditions. The reaction is easily scalable, high yielding, and nearly instantaneous.     

混合多卤甲烷与金属镁反应产生溴氯卡宾及其反应机理的研究

应用CHBr3/CHCl3或CHBr3/CCl4和金属镁在一般的Grignard反应条件下与烯烃反应, 制备偕溴氯环丙烷衍生物。该反应原料易得, 反应条件温和, 产率良好, 后处理方便, 是制备偕溴氯环丙烷衍生物的一种简便的新方法。文中研究了上述反应的单电子转移和自由基链循环的复杂反应机理。     

固体聚合物电解质在肉桂醇电解氧化中的应用(II)——后续化学反应在电催化反应中的地位及其影响因素

对影响肉桂醇电极氧化的各种因素作了进一步的讨论. 实验结果表明固体聚合物电解质内水的含量、pH 以及浸入离子交换膜中的二价锰离子的浓度均对该电极反应的电位以及后续化学反应的速度有很大的影响, 在较高的温度下反应时, 有利手提高生成肉桂醛的电流效率.     

The reduction ring-opening reaction of imidazoline

A new reduction ring-opening reaction of 2-imidazoline with sodium borohydride is reported, and the effect of reaction condition on the yield, reaction mechanism and the use of the new reaction in synthesis of ethylenediamine derivatives are discussed. A new method for the preparation of unsymmetrical substituted ethylenediamine via the reduction ring-opening reaction of imidazoline is provided.     

Investigation of reaction products of sulphuric acid with ilmenite

The reaction of sulphuric acid with titanium raw materials runs violently with simultaneous emission of gases. Such run of reaction creates danger of explosion. This process is very complicated from the reason of complexity of reactions and variety of compounds in reaction mixture. To determine safe conditions of reaction with high efficiency, it is necessary to investigate phase composition products of reaction. Products of reaction were investigated by using X-ray diffraction. However reaction products show high amorphy and this is the reason of difficulties to determine all phases. For this reason also was used additional method — ‘drop’ calorimeter. This method is used for determination of average specific heat of liquid or solid samples. In this case, this method was used for verification of phase composition of products of reaction. On the basis of investigation the phase composition of reaction product is following: titanyl sulfate, iron(III) sulfate, monohydrated iron(II) sulfate, magnesium sulfate and unreacted remainders of ilmenite and magnesium silicate.     

Solid-phase synthesis of alkyl aryl ethers via the Ullmann condensation

Alkyl aryl ether formation is a frequently employed reaction in organic synthesis. Ullmann condensation is an alternative method to the widely used Mitsunobu reaction and is very useful in situations where application of the Mitsunobu reaction is limited. By application of this reaction to solid-phase synthesis of a series of alkyl aryl ethers, reaction conditions (catalyst, solvent, temperature, time, etc.) for a sterically hindered class of alcohols were investigated and optimized. A range of aryl halides was used to explore the scope of the reaction in solid phase.     

Theoretical Analysis of Structural Characteristics of Morin Rearrangement for Cephalosporins Prepared from Penicillin Sulfoxide

The structure of penicillin sulfoxide is rearranged to cephalosporins by the Morin rearrangement. It is a unit reaction for the preparation of various types of cephalosporins. In order to make better use of the reaction and in view of the shortage of the reaction theory, this study used m062x/6-311++G(d, p) to explore the possible ring-opening reaction of the penicillin sulfoxide. It is found that the isomer of(S)-sulfoxide is a necessary structure. At the same time, the intramolecular hydrogen bonding effect between the side-chain amide proton(-CONH-) and the sulfinyl oxygen(-SO) is the decisive structure factor for the formation of alkenyl in ring-opening reaction, and the best reaction path is S0- TS2- IN1 channel. The main effect of acid catalysis is to catalyze the dehydration reaction of sulfenic acid to form sulfur cations for subsequently ring closing reaction.     

Impact of water on the OH + HOCl reaction

The effect of a single water molecule on the OH + HOCl reaction has been investigated. The naked reaction, the reaction without water, has two elementary reaction paths, depending on how the hydroxyl radical approaches the HOCl molecule. In both cases, the reaction begins with the formation of prereactive hydrogen bond complexes before the abstraction of the hydrogen by the hydroxyl radical. When water is added, the products of the reaction do not change, and the reaction becomes quite complex yielding six different reaction paths. Interestingly, a geometrical rearrangement occurs in the prereactive hydrogen bonded region, which prepares the HOCl moiety to react with the hydroxyl radical. The rate constant for the reaction without water is computed to be 2.2 × 10(-13) cm(3) molecule(-1) s(-1) at room temperature, which is in good agreement with experimental values. The reaction between ClOH···H(2)O and OH is estimated to be slower than the naked reaction by 4-5 orders of magnitude. Although, the reaction between ClOH and the H(2)O···HO complex is also predicted to be slower, it is up to 2.2 times faster than the naked reaction at altitudes below 6 km. Another intriguing finding of this work is an interesting three-body interchange reaction that can occur, that is HOCl + HO···H(2)O → HOCl···H(2)O + OH.     

中度气化煤焦异相还原NO机理

采用量子化学密度泛函理论结合热力学和动力学研究了中度气化的锯齿形煤焦异相还原NO的反应机理。分析了中度气化煤焦异相还原NO的反应路径、异相还原过程中的能量变化以及热力学和动力学分析。结果表明,中度气化煤焦更易于NO的吸附,IM2→IM3的开环过程为整个反应的决速步,所需克服能垒最大（398.03 kJ/mol）。中度气化煤焦异相还原NO的反应在煤燃烧系统中为可自发的放热反应,且为单向反应。根据决速步理论,反应的进行需克服较大活化能（389.83 kJ/mol）,同时根据阿伦尼乌斯公式,总体反应速率受温度影响较大,温度越高反应速率越快,越利于NO还原。     

Thermolysis of polyethylene hydroperoxides in the melt, Part 12: Mechanisms and kinetics of thermolysis

The thermolysis of polyethylene hydroperoxides is attributed to the reaction of two hydroperoxide groups. This bimolecular reaction appears as a first-order reaction with the mean values of the hydroperoxide concentrations that can be used for the experimental verification of the kinetics. In low molecular mass liquids and solutions these findings would be irreconcilable. However, in polymer melts, this contradiction is more apparent than real. It is a consequence of the heterogeneous kinetics valid in polymer melts. The bimolecular reaction involves the decomposition of pairs of hydroperoxide groups that are relatively close in the elementary oxidation volumes. By diffusion these hydroperoxide groups can come close enough for reaction. From the chemical point of view the decomposition is a bimolecular reaction. However, from the kinetic point of view it is a first-order reaction of the hydroperoxide pairs. The dependency of the first-order rate on the initial hydroperoxide concentration is explained by the heterogeneous kinetics. The activation energy of the overall process can be related to the sum of the activation energies pertaining to the chemical reaction and to the diffusion process.     

手性磷酸催化剂在不对称合成中的应用

手性磷酸是2004年报道的一类具有新型结构的强酸性Bronsted酸催化剂,近几年来的研究取得了很大的进展,已经成为有机小分子催化剂的一个重要分支。手性磷酸在催化一系列亚胺的加成和还原反应比如Mannich、亚胺的氢转移、亚胺的膦酰化、Pictet-Spengler、 Strecker、aza-Diels-Alder、 Friedel-Craft和α-重氮酯的烷基化等反应时都表现出了非常好的催化活性和立体选择性。本文主要综述了手性磷酸催化剂应用于亚胺相关反应的研究进展。     

Kinetics and mechanism of the additive reaction of aniline with dicyandiamide

Kinetics of the additive reaction of aniline with dicyandiamide resulting in phenylbiguanide production was studied based on the analysis of reaction rate by high performance liquid chromatography. It is a second-order reaction on the condition of the constant temperature and acidity. It is first-order for both aniline and dicyandiamide. The reaction rate is influenced evidently by acidity. It reaches its maximum at pH 2.6. The mechanism for this reaction was suggested that aniline is nucleophilic reagents additive with the protonated cyano-group in dicyandiamide. The rate equation derived from the mechanism can describe the experimental results well. The reaction rate calculated from the rate equation reaches its maximum at pH 2.5, which is close to the experimental result. For different aromatic amine adding to dicyandiamide have the same reaction order, the mechanism ought to be the same. Published in Russian in Kinetika i Kataliz, 2009, Vol. 50, No. 3, pp. 379–385. The article is published in the original.     

甘氨酸螯合钙的合成与性能研究

以甘氨酸和金属钙盐为原料,采用水体系合成法制备甘氨酸钙螯合物,探讨不同反应温度、反应时问、反应体系pH等对产品产率的影响,从而确定反应的最佳条件,并对甘氨酸钙螯合物采用傅里叶红外光谱FT-IR进行表征。实验结果表明,合成甘氨酸钙螯合物的最适反应条件是,反应体系pH为5～6,反应时间为2～3h,反应温度为70～80℃。     

烷基自由基β位裂解反应类反应势垒与速率常数的精确计算

提出反应类等键方法并用于高温燃烧机理中一类重要反应——烷基自由基β位裂解反应的反应势垒和速率常数的精确校正计算. 通过10种不同从头算水平对类反应中5个代表反应的反应势垒的计算发现, 用反应类等键反应方法和直接从头算方法获得的5 个代表反应的反应势垒最大绝对偏差的平均值分别为5.32 和16.16 kJ·mol^-1, 表明反应类等键反应方法计算的反应势垒对不同水平从头算方法的依赖性小, 可在较低从头算水平计算得到精确的反应势垒, 解决大分子体系反应势垒的精确计算问题. 此外应用反应类等键反应方法在BHandHLYP/cc-pVDZ 从头算水平计算了3 个代表反应的速率常数, 并与文献报道的实验值进行了比较, 其在500-2000 K温度区间内计算速率常数与实验速率常数中较大值与较小值的比值k_max/k_min的平均值为1.67, 最大值也仅有2.49. 表明应用反应类等键反应方法在较低从头算水平即可对同类反应的速率常数进行精确计算.最后在BHandHLYP/cc-pVDZ从头算水平用反应类等键反应方法计算了13个烷基自由基β位裂解反应的速率常数.