Ag2SO4-CuSO4 催化-微波消解快速测定炼油污水中化学需氧量

以Ａｇ２ＳＯ４－ＣｕＳＯ４为催化剂,探讨了微波消解测定炼油污水中化学需氧量（Ｃｈｅｍｉｃａｌ Ｏｘｙｇｅｎ Ｄｅｍａｎｄ,ＣＯＤｃｒ）的方法。确定了微波消解测定炼油污水ＣＯＤｃｒ的最佳条件;消解功率、消解时间、混酸介质Ｈ３ＰＯ４－Ｈ２ＳＯ４用量、催化剂配比等。用该方法测定炼油水各处理装置出水 的ＣＯＤｃｒ,与经典的ＣＯＤｃｒ回流法所得结果一致。方法适用于临控生产过程。     

助剂Ag对Cr／γ—Al2O3氧化物催化剂CO氧化性能的影响

本文用硝酸盐水溶液等浸渍法制备了一系列Ｃｒ－Ａｇ／γ－Ａｌ２Ｏ３双金属及单金属的 物催化剂，测定了ＣＯ氧化转化率。用ＢＥＴ，ＸＲＤ，ＴＰＲ，ＴＰＤ－ＭＳ技术研究了助剂Ａｇ对Ｃｒ／γ－Ａｌ２Ｏ３催化剂ＣＯ氧化反应的作用。     

钴铜铝水滑石类化合物的合成及其催化氧化对甲酚：Ⅰ.水滑石的合成及 …

用共沉淀法合成了以钴为主的水滑石型化合物，用ＸＲＤ，ＩＲ等对其及热分解产物进行了表征。结果表明，水滑石经过焙烧，逐渐失去层间的Ｈ２Ｏ，ＯＨ＾＝和ＣＯ＾２－３，转化成尖晶石结构。比表面积测定和ＣＯ２－ＴＰＤ结果表明，焙烧温度和产物的Ｃｏ：Ｃｕ比对表面积和碱性均有明显的影响。     

薄层色谱分离库仑滴定法测定杀虫单

本文提出了用薄层色谱库仑滴定法测定杀虫单（ＳＣＤ）［ＣＨ３）２ＮＨＣ Ｈ（ＣＨ２Ｓ２Ｏ３）２Ｎａ．Ｈ２Ｏ］的方法。试样中的各成分用上行展开法的硅胶Ｇ板上分离，用碘蒸气或喷洒ＰｄＣｌ２溶液确定ＳＣＤ的位置，该试剂与杀虫单反应生成橙黄色产物。     

EuFeO3上CO氧化Redox机理动力学

ＥｕＦｅＯ３用柠檬酸络合法制备，ＥｕＦｅＯ３的钙钛矿物相用ＸＲＤ测定。用ＣＯ还原脉冲及用Ｏ２再氧化脉冲证实在ＥｕＦｅＯ３上ＣＯ氧化为Ｒｅｄｏｘ机理，用外循环流动无梯度反应器研究了ＥｕＦｅＯ３上ＣＯ氧化Ｒｅｄｏｘ动力学。实验结果服从Ｒｅｄｏｘ方程。用正交设计法估计动力学方程的参数。     

原子吸收法测定环境水样中化学需氧量

在Ｈ２ＳＯ４介质中用Ｋ２Ｃｒ２Ｏ７同ＣＯＤ水样反应,反应后水相中过量的Ｃｒ（Ⅵ）以Ｃｒ２Ｏ２－７形式被ＴＯＡ萃入有机相中,而生成的Ｃｒ（Ⅲ）则留在水相,用ＡＡＳ测定有机相中的Ｃｒ（Ⅵ）或水相中的Ｃｒ（Ⅲ）都可求得ＣＯＤ含量。本法简便快速、需样量少、且测定结果同标准方法（ＣＯＤＣｒ法）一致,回收率为９８％～１０８％,平均标准偏差为３．３％。     

差压式BOD测定测定工业废水中BOD

探讨了利用差压式ＢＯＤ测定装置测定工业废水中ＢＯＤ时影响其准确度的几个因素，并提出了相应的改进方法。     

小波变换在差分脉冲伏安法数据处理中的应用

本文根据小波变换不改变信号线性关系的性质，用ＤＯＧ小波函数处理了Ｃｕ－ＫＮＯ３中Ｃｕ＾２＋的差分脉冲伏安法实验数据，结果延长了测定的线性范围。     

贵金属冶金物料中微量钯,铂,铑的双波长分光光度法同量测定的研究

本文提出了用二苄基二硫代乙二酰胺（ＤｂＤＯ）为显色剂分光光度测定铑的方法，并进一步研究了该试剂与钯、铂的反应，从而建立了可在一个试样中同时测定该三元素的方法。在２～３ｍｏｌ／Ｌ ＨＣｌ溶液中，钯与ＤｂＤＯ在室温显色，用氯仿萃取并用８．４ｍｏｌ／Ｌ ＨＣｌ振荡有机相，然后在４５４ｎｍ测定。在萃余液中加入ＳｎＣｌ２，并在沸水浴中加热，使铂、铑的ＤｂＤＯ络合物生成，再用氯仿萃取，８．４ｍｏｌ／Ｌ ＨＣｌ     

TiO2调变对MoO3／γ—Al2O3和CoO—MoO3／γ—Al2O3催化性能的影响

采用气相流动吸附法制备ＴｉＯ２／γ－Ａｌ２Ｏ３复合载体，用浸渍法其担载一定量的ＭｏＯ３或ＣｏＯ－ＭｏＯ３。用ＸＲＤ、ＬＲＳ和ＴＰＲ等技术，考察了Ｍｏ或Ｃｏ－Ｍｏ催化剂的表面结构和还原性能，并有和中压固定床反应装置测定催化剂的噻吩加氢脱硫和环己烯加氢的活性。     

分光光度法测定废水中COD

介绍经微回流管封闭回流的废水样冷却后在HACH分光光度计中测定GOD值的新方法，试验结果表明，本法即快速又节省试剂，相对标准偏差(n=8)和加标回收率均能满足对废水中COD分析测试的质量控制要求。     

Application of microcrystalline cellulose as an efficient and cheap sorbent for the extraction of metoprolol from plasma and wastewater before HPLC–MS/MS determination

A dispersive solid-phase extraction method based on a new sorbent has been performed on plasma and wastewater samples to determine metoprolol by high-performance liquid chromatography–tandem mass spectrometry. In this study, the analyte was adsorbed from the samples onto microcrystalline cellulose as a green and efficient sorbent and then eluted for use in the determination step. In the mass spectrometer, the analyte was detected in the positive mode and selectivity of the analysis was increased by sequential mass analysis through multiple reaction monitoring. All of the effective parameters in the extraction of metoprolol from plasma and wastewater were optimized. Under optimal conditions the method was linear in the ranges of 1–1,000 and 0.1–1,000 ng/ml in plasma and wastewater samples, respectively. The detection limits of the method were 0.30 and 0.03 ng/ml in plasma and wastewater samples, respectively. The data showed that the method provides low detection limit, wide linear range, good precision and high extraction recovery. Finally several plasma and wastewater samples were successfully analyzed using the method. The use of a small amount of a green and inexpensive sorbent and a low volume of plasma without the need for further pretreatment steps are the main advantages of the method.     

Analytical method for the determination of the aminoglycoside gentamicin in hospital wastewater via liquid chromatography-electrospray-tandem mass spectrometry

A method for the determination of gentamicin residues in hospital wastewater has been developed using kanamycin as a surrogate standard. The method consists of solid-phase extraction (SPE) and detection by ion-pair chromatography with electrospray tandem mass spectrometry (LC–ES-tandem MS). The SPE was performed on a weak cation exchanger. Filtration should be avoided in the sample preparation, otherwise a significant loss of gentamicin occurs. Chromatographic separation on a C₁₈-column was achieved using a ternary eluent containing methanol, water and 20 mmol l⁻¹ heptafluorobutyric acid solution. Mean relative recoveries of the analytes in hospital wastewater varied between 107 and 111%. The limit of quantification (LOQ) was 0.20 μg l⁻¹ in hospital wastewater. Gentamicin was found in native hospital wastewater in a concentration range between 0.4 and 7.6 μg l⁻¹.     

Rapid simultaneous determination of 14 sulfonamides in wastewater by liquid chromatography tandem mass spectrometry

This paper describes a rapid method for the determination of 14 kinds of sulfonamides (SAs) in wastewater using SPE, and LC-MS/MS with positive ESI (ESI(+)) and selected reaction monitoring (SRM) mode. The SPE was performed on an Oasis hydrophilic-lipophilic-balanced (HLB) cartridge. Chromatographic separation on a C18 column was achieved using a binary eluent containing methanol and water with 0.2% formic acid. Typical recoveries of the analytes ranged from 22.3 to 87.0% at a fortification level of 100 ng/L. The LODs in wastewater except sulfathiazole (3 ng/L) could be detected and quantified at levels as low as 1 ng/L. Finally, the method was applied to water from the municipal outlet and the aquaculture wastewater effluent. Sulfamethazine (SM(2)), sulfamethoxypyridazine (SMP), and sulfamethoxazole (SMZ) were most frequently found in wastewater in a concentration range between 1.2 and 31.7 ng/L.     

Fully automated determination of N-nitrosamines in environmental waters by headspace solid-phase microextraction followed by GC-MS-MS

A fully automated method for determining nine Environmental Protection Agency N-nitrosamines in several types of environmental waters at ng/L levels is presented. The method is based on a headspace solid-phase microextraction followed by GC-MS-MS using chemical ionization. Three different fibers (carboxen/PDMS, divinylbenzene/carboxen/PDMS, and PEG) were tested. Solid-phase microextraction conditions were best when a divinylbenzene/carboxen/PDMS fiber was exposed for 60?min in the headspace of 10?mL water samples at pH 7 containing 360?g/L of NaCl, at 45°C. All compounds were analyzed by GC-MS-MS within 18?min. The method was validated using effluent from an urban wastewater treatment plant and the LODs ranged from 1 to 5?ng/L. The method was then applied to determine the N-nitrosamines in samples of different complexities, such as tap water and several influent and effluent wastewater samples from urban and industrial wastewater treatment plants and a potable water treatment plant. Although the analysis of influent industrial wastewater revealed high concentrations of some compounds (N-nitrosomorpholine and N-nitrosodimethylamine at μg/L levels), in industrial effluents and other samples, the concentrations were substantially lower (ng/L levels). The new method is suitable for the simple and reliable determination of N-nitrosamines in highly complex water samples in a completely automated procedure.     

Preparation of the Mn-Fe-Ce/γ-Al2O3 ternary catalyst and its catalytic performance in ozone treatment of dairy farming wastewater

The quality of dairy farming wastewater in different regions is particular and different. In Southern China, the Chemical Oxygen Demand (COD_Cr) and colourity of effluent from conventional dairy farming wastewater treatment processes are similar. Catalytic ozonation is a very promising technical method. In this paper, the Mn-Fe-Ce/γ-Al₂O₃ catalyst was prepared via the optimized preparation method of impregnation roasting using γ-Al₂O₃ as the carrier, and this catalyst was used in the ozonation of actual dairy farming wastewater from treatment facilities. The performance of the Mn-Fe-Ce/γ-Al₂O₃ catalyst on dairy farming wastewater was investigated using a simulated dynamic test. The effects of the reaction time, pH and catalyst dosage on COD_Cr and the colourity removal ratio were investigated. The results show that the optimum treatment conditions were a reaction time of 20 min, pH 9, and catalyst dosage of 15 g/L. The COD_Cr removal ratio reached 48.9% and the colourity was 95% under the optimum conditions. BOD₅/COD_Cr increased from 0.21 to 0.54 after catalytic ozonation, indicating that the biodegradability of wastewater was significantly improved. This research provides a new method and theoretical guidance for dairy farming wastewater treatment.     

Analysis of formaldehyde formation in wastewater using on-fiber derivatization-solid-phase microextraction-gas chromatography-mass spectrometry

A method has been developed for the quantification of the formation of formaldehyde during the advanced oxidation treatment (AOT) of wastewater destined for reuse. This method uses solid-phase microextraction (SPME) with on-fiber derivatization followed by gas chromatography-mass spectrometry (GC-MS) analysis. Based on calculated method detection limits (MDL) and ambient background levels, the method reporting (MRL) limit for formaldehyde was set at 10 microg/L. Precision for formaldehyde using this technique resulted in 23% relative standard deviation (RSD), while the internal standard, acetone-d(6), was only 6%. This method was used to evaluate the formation of formaldehyde in bench scale UV-AOT experiments using natural organic matter (NOM) fortified reagent water and tertiary treated wastewater effluent. Results suggest that the formation of formaldehyde increases in both the reagent water and wastewater matrices with increasing UV exposure and hydrogen peroxide concentrations, with overall higher concentrations of formaldehyde in the wastewater samples. No appreciable amount of formaldehyde formation was observed when UV was applied in the absence of hydrogen peroxide in both matrices tested.     

Serial mixed-mode cation- and anion-exchange solid-phase extraction for separation of basic,neutral and acidic pharmaceuticals in wastewater and analysis by high-performance liquid chromatography–quadrupole time-of-flight mass spectrometry

A novel solid-phase extraction (SPE) method is presented whereby 15 basic, neutral and acidic pharmaceuticals in wastewater were simultaneously extracted and subsequently separated into different fractions. This was achieved using mixed-mode cation- and anion-exchange SPE (Oasis MCX and MAX) in series. Analysis was performed by high-performance liquid chromatography–quadrupole time-of-flight mass spectrometry (HPLC/QTOF-MS). A fast separation was achieved, with all compounds eluting within 6 min, narrow chromatographic peaks, with a peak base width of 6 s on average, and a high mass accuracy of quantified wastewater sample ions, with average mass errors in absolute value of 0.7 mDa or 2.7 ppm. The recovery of the SPE method in the analysis of sewage treatment plant (STP) influent and effluent wastewater was on average 80% and the ion suppression 30%. For less demanding samples Oasis MCX used alone may be an alternative method, although for STP influent waters containing high loads of organic compounds the clean-up achieved using only Oasis MCX was insufficient, leading to unreliable quantitation. Furthermore, serial SPE separation according to molecular charge added an additional degree of analyte confirmation. For quantitation, an approach combining external standard calibration curves, isotopically labelled surrogate standards and single-point standard addition was used. The applicability of the method was demonstrated in the analysis of influent and effluent wastewater from an STP, using small sample volumes (25–50 mL). The effluent wastewater had been subjected to three different treatments; activated sludge, activated sludge followed by ozonation, and a membrane bioreactor (MBR). Ozone treatment proved superior in removal of the analysed pharmaceuticals, while the MBR provided higher removal efficiencies than the activated sludge process.     

An alternative method for the measurement of mineral sulphide in wastewater

A simple and rapid procedure for sulphide measurement in crude oil refinery wastewater has been developed. This method is based on the knowledge of the UV response of sulphur compounds and the mathematical deconvolution of the sample spectrum using reference spectra (specific compounds or aggregate spectra). The detection limit of the method is 0.5 mg l(-1) for a quartz cell pathlength of 10 mm. The range is up to 15 mg l(-1). The method has been validated for crude oil refinery wastewater. Compared to conventional methods, the UV determination is quicker and easier to run.     

Determination of pharmaceutical and personal care products in wastewater by capillary electrophoresis with UV detection

Capillary electrophoresis (CE) offers a fast and cost-effective alternative analytical technique to LC-MS/MS for separation and quantitation of many PPCP compounds in wastewater. In this study, we have developed a method that can simultaneously analyze eight different PPCP compounds in untreated wastewater (ibuprofen, triclosan, carbamazepine, caffeine, acetaminophen, sulfamethoxazole, trimethoprim, and lincomycin), using capillary electrophoresis with UV detection (CE-UV). The method detection limit (MDL) ranged from 1.6 to 68.7 ppb through solid phase extraction. The standard limit of quantification (LOQ) ranged from 0.63 to 7.72 ppm. Factors affecting separation and quantification of PPCPs, such as pH, electrophoretic potential, buffer strength, buffer type, and additives, were investigated and optimized. Water samples from two different wastewater treatment plants were collected and analyzed. The results obtained were comparable with those of LC-MS/MS. The technique developed in this study provides a low cost, simple, fast, and relatively sensitive method for determination of various PPCPs in wastewater samples for PPCP screening.