Li/富锂钒青铜(Li_6V_6O_(15))二次电池正极材料研究

近年来,人们对二次锂电池的正极进行了不少研究。许多过渡金属氧化物或硫化物,如V_6O(13),Li_(1+x)V_3O_8,TiS_2,MoS_2等被认为是较好的正极材料。Pistoia等研究了Li_(1+x)V_3O_8钒青铜的电化学性能得出,当Li浓度高时,由于电子定域作用使电荷屏蔽效应     

Y3+, S6+掺杂的矿物锂快离子导体Li1.2+x-yYxTi1.9-xAl0.1Si0.1SyP2.9-yO12系统的合成与表征

以LiTi2(PO4)3为母体,以天然高岭石为起始原料,经高温固相反应制得了一系列新的锂快离子导体Li1.2+x-yYxTi1.9-xAl0.1Si0.1SyP2.9-yO12(以下简称Y-S-Lisicon).X射线粉末衍射分析结果表明在x≤0.3,y＜(0.2+x)的组成范围内均能得到类似于Nasicon三方结构的相,同时还存在其他杂相.应用交流阻抗技术测定电导率的结果表明起始组成为x=0.1,y＝0.15的合成物电导率最高,其在室温下的电导率为2.93×10-5 S·cm-1,在673 K时可达3.62×10-2 S·cm-1,其在473～673 K间的活化能为37.19 kJ·mol-1,分解电压为3.0 V.     

钠快离子导体Na1+xZr2-yTiySixP3-xO12系统的研究(Ⅱ)

本文介绍钠快离子导体Na_(1+x)Zr(3-y)Ti_y Si_xP_(3-x)O_(12)系统中x=2.0,y=0—2.0的一系列合成物的合成条件、相变关系及其两个单纯相—311相(相当于起始组成为Na_(3.0)Zr_(1.0)Ti_(1.0)Si_(2.0)P_(1.0)O_(12.0)和302相(相当于起始组成为Na_(3.0)Ti_(2.0)Si_(2.0)P_(1.0)O_(12.0)的电导率和激活能。 室温时,311相和302相的电导率分别为0.78×10~(-4)(Ω·cm)~(-1)和0.30×10~(-4)(Ω·cm)~(-1)。623K时,311相和302相的电导率则是0.49×10~(-1)(Ω·cm)~(-1)和0.44×10~(-4)(Ω·cm)~(-1)。在473K—623K温区里,311相和302相的电导激活能各为43.01kJ/mole和46.26kJ/mole。     

钠快离子导体Na1+xZr2-yTiySixP3-xO12系统的研究Ⅲ

通过高温固相反应合成了Na_(1+x)Zr_(2-y)Ti_y,Si_xP_(3-x)O_(12)系统y=1,x=0-2.0的一系列合成物.其合成反应温度低于Zr-NASICON的合成温度.研究了系统的相变关系以及电导率、电导激活能与化学组成的关系.研究了系统合成物对水的稳定性.结果表明y=1.0,x=0.9的合成物的电导性能最好,对水的反应性也较小,其电导率在室温时为3.64×10~(-4)(Ω·cm~(-1)),在623K时为1.25×10~(-1)(Ω·cm)~(-1),其激活能为26.35kJ/molc(0.27cV)(473-673K).     

Y3+,W6+掺杂的矿物锂快离子导体Li1.2+x-yYxTi1.9-xAl0.1Si0.1WyP2.9-yO12系统的合成与表征

以LiTi2(PO4)3为母体,以天然高岭石为起始原料,经高温固相反应制得了一系列新的锂快离子导体Li1.2+x-yYxTi1.9-xAl0.1Si0.1WyP2.9-yO12(以下简称Y-W-Lisicon).X射线粉末衍射分析结果表明,在x＝0.10,y≤0.20及x＝0.20,y≤0.20的组成范围内能得到空间群为R3c,类似于Nasicon的三方结构,但在上述组成范围内均有杂相存在.应用交流阻抗技术测定电导率的结果表明,起始组成为x=0.10,y=0.10的样品在室温下具有较高的离子电导率,为1.65×10-5 S·cm-1;组成为x=0.20,y=0.10的样品在573 K时具有较高的离子电导率,为6.53×10-3 S·cm-1,该样品的分解电压为3.0 V.     

钠快离子导体Na1+xZr2-yTiySixP3-xO12系统研究(Ⅰ)

以Na_3PO_4、ZrP_2O_7、SiO_2、ZrO_2、TiO_2为反应原料,在1173K—1473K的高温下进行固相反应,制备了钠快离子导体Na_(1 x)Zr_(2-y)Ti_ySi_xP_(3-x)O_(12)系统中x=1、y=0—2.0的一系列合成物。研究了它们的相变关系;测定了两个单纯相—211相和202相的电导率和电导激活能。 室温时,211相的电导率σ_(RT)=1.52×10~(-4)(Ω·cm)~(-1),202相的σ_(TR)=0.53×10~(-4)(Ω·cm)~(-1);623K时,211相的电导率σ_(623)=1.21×10~(-1)(Ω·cm)~(-1),202相的σ_(623)=0.88×10~(-2)(Ω·cm)~(-1)。 在523K～673K温区里,211相的电导激活能E_a为31.87kJ/mole,202相的E_a为33.16kJ/mole。     

矿物及炉渣中钒钛物相分析概述

概述了我国十多年来矿物及炉渣中钒、钛的物相分析。用扫描电子显微镜和场离子显微分析查明炉渣中有Ti_4CS_2和Fe·V_2O_3、(V、Ti)C_2等新的化学物相。钒、钛的化学物相分析研究结果表明,可以定量测定炉渣和矿物中V(金属)、VC、VN、FeO·V_2O_3、TiC、TiN、TiO与Ti_2O_3化合物相和钒渣中各价态VO、V_2O_3、VO_2化合物的量及钒钛磁铁矿(Fe_3O_4·T(?)O_2)、铁铁矿(FeO·TiO_2)和金红石(a-TiO_2)的量。     

纳米LaF3块体材料常温离子电导率的研究

采用水溶液直接沉淀法成功制备了LaF3纳米粉体.用透射电子显微镜(TEM)观察了粒子形貌及粒度,粒子呈球形,粒径范围在10～20 nm之间,粉体单分散性良好.用X射线衍射(XRD)分析得到的平均粒径16.7 nm.采用真空高压固结法在真空度10-4 Pa条件下常温加压至1 GPa制备了纳米LaF3块体材料.采用交流阻抗谱研究了纳米LaF3的室温离子电导率,发现纳米LaF3的室温离子电导率(10-5 S·cm-1)和单晶LaF3的室温离子电导率(10-6 S·cm-1)相比有明显提高.观察到由于纳米材料的弛豫引起电导率随测试次数增大的现象.     

高氯酸锂与1,3-氮氧杂环-戊-2-酮形成的二元熔盐电解质

制备了高氯酸锂(LiClO4)与1,3-氮氧杂环-戊-2-酮(OZO)形成的二元熔盐电解质, 虽然先导物具有较高的熔点, 但二者可形成均一、稳定的共熔体系, 测试结果表明该熔盐体系具有低的共熔温度(-50 益). 红外光谱分析表明OZO 通过Li—O 键与LiClO4中Li+配位而破坏了LiClO4的离子键,形成很大的配位阳离子,削弱了阴阳离子间的库伦作用力; 同时Li—O 配位也导致OZO 分子间的氢键断裂, 因而体系的共熔温度较之纯物质熔点显著降低, 部分样品室温下以液体状态稳定存在. 采用交流阻抗法和循环伏安法对其电化学性质进行研究, 结果显示, 配比n(LiClO4):n(OZO)=1:4.5 的样品室温(25 ℃)电导率为0.66×10^-3 S·cm^-1, 80 ℃电导率为7.33×10^-3 S·cm^-1; 其电化学稳定电位窗口约为3.5 V.     

碳酸丙烯酯分子凝胶电解质的电化学行为

碳酸丙烯酯 (PC)在凝胶因子 4 ,4′ 二 (硬脂酰胺基 )二苯醚 (BSDE)的作用下形成分子凝胶。交流阻抗法研究发现 ,含二 (三氟甲基磺酰 )亚胺锂 (LiTFSI)的PC分子凝胶在室温下的电导率达 5 .5 6× 1 0 -3 S·cm-1 。在较低温度下 (≥ - 35℃ ) ,温度对分子凝胶电导率的影响比其溶液电解质的影响大。在 - 35℃时 ,含LiTFSI的PC分子凝胶的电导率为 5 .91× 1 0 -5S·cm-1 。以不锈钢电极为工作电极 ,锂电极为参比电极 ,用循环伏安法 ,测定PC分子凝胶电解质体系的电化学稳定窗口为 0 .0～ 4 .7V。     

固体电解质Ce_(0.9)Er_(0.1-x)Pr_xO_(1.95+δ)的微观结构及电性能

采用柠檬酸溶胶-凝胶法制备了固体电解质Ce0.9Er0.1-xPrxO1.95+δ(x=0.02~0.08),利用X射线粉末衍射(XRD)、原子力显微镜(AFM)、拉曼光谱(Raman)、X射线光电子能谱(XPS)和交流阻抗谱研究了样品的微观结构和电性能.XRD结果表明,800℃煅烧的所有样品均形成了单相立方萤石结构;Raman光谱结果表明,Ce0.9Er0.05Pr0.05O1.95+δ具有氧缺位的立方萤石结构;XPS分析表明,Ce0.9Er0.05Pr0.05O1.95+δ存在氧缺位,Pr3+离子和Pr4+离子共存;AFM观测结果表明,1300℃下烧结的样品比1400℃下烧结的样品致密;交流阻抗谱结果表明,Pr掺杂量x=0.05时,Ce0.9Er0.05Pr0.05O1.95+δ的电导率最高(σ600℃=1.34×10-2S/cm,Ea=0.90 e V),比未掺杂Pr的Ce0.9Er0.1O1.95(σ600℃=8.81×10-3S/cm,Ea=0.92 e V)提高了52%,说明在Ce0.9Er0.1O1.95中适量掺杂Pr可提高材料的电导率,降低活化能.     

锌掺杂提高LiNi1/3Co1/3Mn1/3O2正极材料的电化学稳定性

通过共沉淀法与固相法相结合制备了掺锌的高稳定性Li(Ni_1/3Co_1/3Mn_1/3)_1-xZn_xO₂ (x=0, 0.02, 0.05)正极材料. 循环伏安(CV)曲线表明Zn掺杂使氧化峰与还原峰的电势差减小到0.09 V, 电化学阻抗谱(EIS)曲线表明Zn掺杂使电极的阻抗从266 Ω减小到102 Ω. Li⁺嵌入扩散系数从1.20×10^-11 cm²·s^-1增大到 2.54×10^-11 cm²·s^-1. Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以0.3C充放电在较高的截止电压(4.6 V)下比其他两种材料的电化学循环性能更稳定, 其第二周的放电比容量为176.2 mAh·g^-1, 循环100周后容量几乎没衰减; 高温(55 °C)下充放电循环100周, 其放电比容量平均每周仅衰减0.20%, 远小于其他两种正极材料(LiNi_1/3Co_1/3Mn_1/3O₂平均每周衰减0.54%; Li(Ni_1/3Co_1/3Mn_1/3)_0.95Zn_0.05O₂平均每周衰减0.38%). Li(Ni_1/3Co_1/3Mn_1/3)_0.98Zn_0.02O₂正极材料以3C充放电时其放电比容量可达142 mAh·g^-1, 高于其他两种正极材料. 电化学稳定性的提高归因于Zn掺杂后减小了电极的极化和阻抗, 增大了锂离子扩散系数.     

锂离子电池正极材料LiNi0.5Co0.2Mn0.3O2的合成及其高温容量衰减研究

采用共沉淀-高温固相烧结法合成了富镍型三元复合正极材料LiNi0.5Co0.2Mn0.3O2.恒流充放电测试表明,材料在3.0～4.4 V下0.2C放电容量达到179.2 mAh.g-1,但在55℃下经历100次充放电循环后发生急剧的容量衰减.电化学交流阻抗谱、X射线光电子能谱和原子发射光谱等实验表明,在高温高电压下,电解液与LiNi0.5Co0.2Mn0.3O2电极材料之间的副反应加剧,导致过渡金属原子溶出,该材料局域结构被破坏.同时,电极材料表面还沉积了高阻抗的LiF/MFx层,使得在电极的充放电过程中电荷转移阻抗和Li+扩散阻抗不断增加,以致电池容量急剧衰减.     

Protic ionic liquid-based gel polymer electrolyte: structural and ion transport studies and its application in proton battery

Proton-conducting free standing gel polymer electrolyte (GPE) films containing protic ionic liquid, 1-butyl-3-methylimidazolium hydrogen sulphate, immobilized in blend of poly(vinylidenefluoride-co-hexafluoropropylene) and poly(vinylpyrrolidone) have been prepared by solution-cast technique. Films have been characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM), differential scanning calorimetry (DSC), complex impedance spectroscopy, and cyclic voltammetry. Ionic conductivity of the semicrystalline and porous GPE films has been obtained as ~3.9?×?10^?3 S cm^?1 at room temperature. Protonic nature of conduction in the films has been established by performing cyclic voltammetry and complex impedance spectroscopy on the cells having both blocking (stainless steel) and both reversible electrodes (Zn + ZnSO₄.7H₂O). The electrochemical stability window of the films has been found as ~3.8 V. The highest conducting film has been used as a separator and proton conductor to fabricate a proton battery of configuration Zn + ZnSO₄.7H₂O |GPE film| PbO₂ + V₂O₅. The battery shows an open circuit voltage of ~1.62 V. Energy density of the cell has been obtained as 35.2 W h kg^?1 for low current drain. Rechargeability of the cell has been tested for ten cycles. The maximum discharge capacity of the cell has been obtained as ~2.50 mA h g^?1 during the first discharge cycle.     

有序介孔氮掺杂碳负载三氧化二铁的制备及其催化氧还原性能

制备了有序介孔氮掺杂碳负载三氧化铁,有效降低了氧还原的过电势。通过扫描电子显微镜、透射电子显微镜、氮气吸附-脱附测试、粉末X射线衍射、X射线光电子能谱、拉曼光谱等技术表征了所制备的催化剂的物理化学性质。此外,用旋转圆盘电极测试了其在碱性条件下对氧还原反应的催化活性和选择性。实验结果表明:氮气热解后铁以三氧化二铁的形式负载于有序介孔氮掺杂碳中,其比表面积达到755 cm^2·g^-1。拉曼和X射线光电子能谱结果表明,加入铁前驱体后所制备的催化剂石墨化程度有所提升、阻抗降低、导电性增加。在碱性条件下,Fe2O3@NC催化剂呈现出4电子氧还原反应,其起始电位(-0.01 V vs Ag/AgCl)和半波电位(-0.13 V vs Ag/AgCl)与商用20%Pt/C相当。此外,该催化剂具有较好的抗甲醇性能且其恒电压稳定性优于商用Pt/C。Fe2O3@NC催化剂用于锌-空电池放电测试,其放电功率可以达到88 mW·cm^-2,是商用Pt/C的1.29倍。     

Vanadyl(IV) complexes of 4-alkoxy substituted [N,O] donor salicylaldimine Schiff bases derived from chloro-/nitro-aniline: synthesis,mesomorphism, and DFT study

Oxovanadium(IV)-Schiff-base complexes, [VOL₂] {L?=?N,N′-bis-(4-X-amino phenyl (4′-n-alkoxy)-salicylaldiminato), n?=?10, 18; X?=?Cl, NO₂}, have been synthesized from the interaction of vanadyl (VO²⁺) and the bidentate [N,O] donor in methanol/ethanol. The compounds were characterized by FT–IR, ¹H- and ¹³C-NMR, FAB-mass spectra, elemental analyses, and solution electrical conductivity. Mesomorphic behavior of the ligands and their vanadyl complexes were probed by polarizing optical microscopy and differential scanning calorimetry. The compounds are thermally stable and exhibit enantiotropic smectic A mesomorphism over the temperature range of 57–231°C. The mesophase–isotropic transition temperatures for the complexes are much higher than the ligands. Melting and clearing points of the compounds did not show any definitive trend with regards to alkoxy chain length or electronegative substituent. Variable temperature magnetic susceptibility measurements of the vanadyl complexes clearly show the absence of exchange interactions among the vanadyl spin centers. Non-electrolytic natures of the complexes were shown by conductometric measurements. A ν(V=O) of ～970?cm^?1 corroborated the absence of any V=O?···?V=O interactions. Density functional theory study carried out using DMol3 at BLYP/DNP level to determine the energy-optimized structure revealed a distorted square pyramidal geometry for the vanadyl complexes.     

Synthesis and characterization of cancrinite-type zeolite, and its ionic conductivity study by AC impedance analysis

The synthesis of cancrinite in the system NaOH-SiO₂-Al₂O₃-NaHCO₃-H₂O was performed, according to methods described in the literature, in an autoclave under hydrothermal conditions at T = 473 K. The electrical properties of cancrinite-type zeolite pellets were investigated by complex impedance spectroscopy in the temperature range 465?C800°C. The effect of temperature on impedance parameters was studied using an impedance analyzer in a wide frequency range (1 Hz to 13 MHz). The real and imaginary parts of complex impedance trace semicircles in the complex plane are plotted. The bulk resistance of the material decreases with rise in temperature. This exhibits a typical negative temperature coefficient of resistance (NTCR) behavior of the material. The results of bulk electrical conductivity and its activation energy are presented. The modulus analysis suggests that the electrical transport processes in the material are very likely to be of electronic nature. Relaxation frequencies follow an Arrhenius behavior with activation energy values not comparable to those found for the electrical conductivity.     

Li1.5Al0.5Ge1.5(PO4)3基固体复合电解质的制备及锂离子导电行为

将聚氧化乙烯(PEO)和二(三氟甲基磺酰)亚胺锂(LiTFSI)混合(固定EO/Li摩尔比为13)后, 采用溶液浇注法制备了一系列不同Li_1.5Al_0.5Ge_1.5(PO₄)₃(LAGP)与PEO质量比的LAGP-PEO(LiTFSI)固体复合电解质体系. 结合电化学阻抗法、 表面形貌表征以及与惰性陶瓷填料(SiO₂, Al₂O₃) 性能的对比分析, 探讨了LAGP在固体复合电解质中的作用机理以及锂离子的导电行为. 结果表明, 在以LAGP为主相的固体复合电解质中, PEO主要处于无定形态, 整个体系主要为PEO与LiTFSI的络合相、 LAGP与PEO(LiTFSI)相互作用形成的过渡相和LAGP晶相. 其中LAGP作为主要的导电基体不仅起到降低PEO结晶度、 改善两相导电界面的作用; 同时自身也可以作为离子传输的通道, 降低锂离子迁移的活化能, 从而使离子电导率得到提高. 当LAGP与PEO的质量比为6:4时, 固体复合电解质的成膜性能最好, 离子电导率最高, 在30 ℃时为2.57×10^-5 S/cm, 接近LAGP的水平, 电化学稳定窗口超过5 V.     

Zn/V2O5水相二次电池的交流阻抗研究

The dependence of charge transfer resistances of electrodes in the aqueous Zn/V 2O 5 secondary battery on the Zn 2+ amount intercalated was studied by means of AC impedance experiments. The results showed that the electrode reaction on cathode was controlled by the diffusion of Zn 2+ at the beginning of the discharge process. With the increase of Zn 2+ amount intercalated into the cathode, the reaction became a kinetic controlled process, i.e.a process controlled by intercalation of Zn 2+ in V 2O 5.