Dispersive elastodynamics of 1D banded materials and structures: analysis

The elastodynamics of 1D periodic materials and finite structures comprising these materials are studied with particular emphasis on correlating their frequency-dependent characteristics and on elucidating their pass-band and stop-band behaviors. Dispersion relations are derived for periodic materials and are employed in a novel manner for computing both pass-band and stop-band complex mode shapes. Through simulations of harmonically induced wave motion within a finite number of unit cells, conformity of the frequency band structure between infinite and finite periodic systems is shown. In particular, only one or two unit cells of a periodic material could be sufficient for “frequency bandedness” to carry over from the infinite periodic case, and only three to four unit cells are necessary for the decay in normalized transmission within a stop band to practically saturate with an increase in the number of cells. Dominant speeds in the scattered wave field within the same finite set of unit cells are observed to match those of phase and group velocities of the infinite periodic material within the most active pass band. Dynamic response due to impulse excitation also is shown to capture the infinite periodic material dynamical characteristics. Finally, steady-state vibration analyses are conducted on a finite fully periodic structure revealing a conformity in the natural frequency spread to the frequency band layout of the infinite periodic material. The steady-state forced response is observed to exhibit mode localization patterns that resemble those of the infinite periodic medium, and it is shown that the maximum localized response under stop-band conditions could be significantly less than in an equivalent homogenous structure and the converse is true for pass-band conditions.     

Photoacoustic study of the transmission of wide-band ultrasonic signals through periodic one-dimensional structures

The propagation of wide-band acoustic pulses in one-dimensional periodic structures consisting of alternating plexiglas and water layers is studied theoretically and experimentally. The experiment is carried out with the use of the wide-band photoacoustic spectroscopy based on the laser excitation of ultrasound and a wide-band signal detection. The fact that the transmission spectrum of a periodic structure has alternating pass and stop bands is confirmed experimentally. The width and localization of the stop bands strongly depend on the thickness of the layers and on the phase velocity of ultrasound in them. It is demonstrated that defects of the structure periodicity give rise to one or several local transmission maxima in the stop band and to a modification of the pass band. The amplitude and position of a local maximum in the stop band strongly depend on the position of the defective layer. The experimental data agree well with the results of numerical simulation.     

Passive reduction of gear mesh vibration using a periodic drive shaft

In this paper, a passive approach to reduce transmitted vibration generated by gear mesh contact dynamics is presented. The approach utilizes the property of periodic structural components that creates stop band and pass band regions in the frequency spectra. The stop band regions can be tailored to correspond to regions of the frequency spectra that contain harmonics and sub-harmonics of the gear mesh frequency, attenuating the response in those regions. A periodic structural component is comprised of a repeating array of cells, which are themselves an assembly of elements. The elements may have differing material properties as well as geometric variations. For the purpose of this research, only geometric variations are considered and each cell is assumed to be identical. A periodic shaft is designed and machined in order to reduce transmitted vibration of a pair of spur gears. Analytical and experimental results indicate that transmitted vibrations from gear mesh contact to the bearing supports are reduced at a variety of operational speeds under static torque preload.     

Ultrawide low frequency band gap of phononic crystal in nacreous composite material

The band structure of a nacreous composite material is studied by two proposed models, where an ultrawide low frequency band gap is observed. The first model (tension-shear chain model) with two phases including brick and mortar is investigated to describe the wave propagation in the nacreous composite material, and the dispersion relation is calculated by transfer matrix method and Bloch theorem. The results show that the frequency ranges of the pass bands are quite narrow, because a special tension-shear chain motion in the nacreous composite material is formed by some very slow modes. Furthermore, the second model (two-dimensional finite element model) is presented to investigate its band gap by a multi-level substructure scheme. Our findings will be of great value to the design and synthesis of vibration isolation materials in a wide and low frequency range. Finally, the transmission characteristics are calculated to verify the results.     

Vibration reduction in piecewise bi-coupled periodic structures

The problem of minimizing transmitted vibrations through finitely long periodic structures is addressed. Bi-coupled periodic element properties and arrangement are tailored to localize the response around the excitation source within any assigned frequency range. Bi-dimensional analytical maps of the single unit free-wave propagation domains (stop, pass and complex domains) provide the optimal choice of the cell properties and ordering. Moreover, the amount of vibration suppression along the periodic structure is also controlled as it can be described through iso-attenuation curves representing the contour plot of the real part of the propagation constants. Applications to both undamped and damped beams resting on elastic supports are illustrated. The response of the periodic structures to harmonic excitations is expressed through the wave vector method taking into account the effects of wave reflection due to changes in the cell properties along the structure and boundary conditions. Such computational schemes enables one to overcome numerical difficulties arising in the transfer matrix formulation for structures with a large number of periodic units.     

Nonlinear pulse propagation in periodic media with and without defects

The influence of single defects within a periodic structure on the nonlinear transmission of optical pulses through the structure is investigated numerically. A stack of alternating linear and cubically nonlinear layers of submicron thicknesses is considered. The simulations are based on a modified equation for the pulse envelope. Diffraction of the pulse has been taken into account, too. The results of simulations have been demonstrated as an essential influence of defects within the periodic structure on the nonlinear propagation of optical pulses, when the carrier frequency is chosen within the stop band of the structure with the defect.     

Complete flexural vibration band gaps in membrane-like lattice structures

The propagation of flexural vibration in the periodical membrane-like lattice structure is studied. The band structure calculated with the plane wave expansion method indicates the existence of complete gaps. The frequency response function of a finite periodic structure is simulated with finite element method. Frequency ranges with vibration attenuation are in good agreement with the gaps found in the band structure. Much larger attenuations are found in the complete gaps comparing to those directional ones. The existence of complete flexural vibration gaps in such a lattice structure provides a new idea for vibration control of thin plates.     

Light exiting from real photonic band gap crystals is diffuse and strongly directional

Any photonic crystal is in practice periodic with some inevitable fabricational imperfections. We have measured angle-resolved transmission of photons that are multiply scattered by this disorder in strongly photonic crystals. Peculiar non-Lambertian distributions occur as a function of frequency: due to internal diffraction, wide angular ranges of strongly reduced diffuse transmission coincide with photonic stop bands, while enhancements occur for directions outside stop gaps. We quantitatively explain the experiment with a model incorporating diffusion and band structure on equal footing. We predict that in the event of a photonic band gap, diffuse light at frequencies near band gap edges can exit only along isolated directions. Angle-resolved diffuse transmission appears to be the photonic equivalent of angle-resolved photoelectron spectroscopy.     

Theoretical and Experimental Investigation of Flexural Vibration Transfer Properties of High-Pressure Periodic Pipe

According to the theory of phononic crystals,the hydraulic pipeline is designed to be a periodic structure composed of steel pipes and hoses to suppress the vibration of the hydraulic system with band gaps.We present theoretical and experimental investigations into the flexural vibration transfer properties of a high-pressure periodic pipe with the force on the inner pipe wall by oil pressure taken into consideration.The results show that the vibration attenuation of periodic pipe decreases along with the elevation of working pressure for the hydraulic system,and the band gaps in low frequency ranges move towards high frequency ranges.The periodic pipe has good vibration attenuation performance in the frequency range below 1000 Hz and the vibration of the hydrauhc system is effectively suppressed.All the results are validated by experiment.The experimental results show a good agreement with the numerical calculations,thus the flexural vibration transfer properties of the highpressure periodic pipe can be precisely calculated by taking the Quid structure interaction between the pipe and oil into consideration.This study provides an effective way for the vibration control of the hydraulic system.     

Propagation of elastic waves through two-dimensional lattices of cylindrical empty or water-filled inclusions in an aluminum matrix

The layer-multiple-scattering method is developed to study wave propagation through two-dimensional lattices of cylindrical inclusions in an elastic medium. The lattices are a series of periodically spaced infinite one-dimensional periodic gratings (or rows) of inclusions. The layer-multiple-scattering method allows the analysis of the reflection and transmission properties of the two-dimensional lattice, provided those of each row are known. These are later determined by means of an exact multiple scattering formalism based on modal series developments. A new characteristic equation is obtained that describes the Bloch wave propagation into the infinite lattice. Lattices with empty and fluid-filled inclusions are compared. The comparison shows the existence of pass and stop bands due to the resonances of the fluid-filled inclusions. Resonant inclusions allow the opening of narrow pass bands inside phononic stop band, which is an interesting phenomenon for demultiplexing problems. It is worth noting that inclusion resonances have nothing to do with resonances due to defects, as they involve the whole lattice. In addition, it is shown that stop bands, at an oblique incidence, due to a strong coupling between longitudinal and transverse waves, are related to dispersive guided waves that propagate in the direction of the reticular planes of the lattices.     

Vibro-acoustic response and sound transmission loss analysis of functionally graded plates

This paper presents analytical studies on the vibro-acoustic and sound transmission loss characteristics of functionally graded material (FGM) plates using a simple first-order shear deformation theory. The material properties of the plate are assumed to vary according to power law distribution of the constituent materials in terms of volume fraction. The sound radiation due to sinusoidally varying point load, uniformly distributed load and obliquely incident sound wave is computed by solving the Rayleigh integral with a primitive numerical scheme. Displacement, velocity, acceleration, radiated sound power level, radiated sound pressure level and radiation efficiency of FGM plate for varying power law index are examined. The sound transmission loss of the FGM plate for several incidence angles and varying power law index is studied in detail. It has been found that, for the plate being considered, the sound power level increases monotonically with increase in power law index at lower frequency range (0–500 Hz) and a non-monotonic trend is appeared towards higher frequencies for both point and distributed force excitations. Increased vibration and acoustic response is observed for ceramic-rich FGM plate at higher frequency band; whereas a similar trend is seen for metal-rich FGM plate at lower frequency band. The dBA values are found to be decreasing with increase in power law index. The radiation efficiency of ceramic-rich FGM plate is noticed to be higher than that of metal and metal-rich FGM plates. The transmission loss below the first resonance frequency is high for ceramic-rich FGM plate and low for metal-rich FGM plate and further depends on the specific material property. The study has found that increased transmission loss can be achieved at higher frequencies with metal-rich FGM plates.     

Buckling and free vibration analysis of functionally graded cylindrical shells subjected to a temperature-specified boundary condition

Linear thermal buckling and free vibration analysis are presented for functionally graded cylindrical shells with clamped-clamped boundary condition based on temperature-dependent material properties. The material properties of functionally graded materials (FGM) shell are assumed to vary smoothly and continuously across the thickness. With high-temperature specified on the inner surface of the FGM shell and outer surface at ambient temperature, 1D heat conduction equation along the thickness of the shell is applied to determine the temperature distribution; thereby, the material properties based on temperature distribution are made available for thermal buckling and free vibration analysis. First-order shear deformation theory along with Fourier series expansion of the displacement variables in the circumferential direction are used to model the FGM shell. Numerical studies involved the understanding of the influence of the power-law index, r/h and l/r ratios on the critical buckling temperature. Free vibration studies of FGM shells under elevated temperature show that the fall in natural frequency is very drastic for the mode corresponding to the lowest natural frequency when compared to the lowest buckling temperature mode.     

Interplay of local resonances and Bragg band gaps in acoustic waveguides with periodic detuned resonators

This letter is concerned with acoustic wave propagation and transmission in acoustic waveguides with periodically grafted detuned Helmholtz resonators. The interplay of local resonances and Bragg band gaps in such periodic systems is examined. It is shown that, when the resonant frequencies of the resonators are tuned close to a Bragg band gap, the behavior of the Bragg band gap can be affected dramatically. Particularly, by introducing appropriately tuned resonators, the bandwidth of a Bragg band gap can be reduced to zero, leading to a very narrow pass band with great wave attenuation performance near both band edges. The band formation mechanisms of such periodic waveguides are further examined, providing explicit formulae to locate the band edge frequencies of all the band gaps, as well as the conditions to achieve very narrow pass bands in such periodic waveguides.     

基于波传播法的周期复合板振动带隙衰减特性研究

运用波传播法对有限和无限周期对边简支复合板的振动带隙衰减特性进行了研究.在建立相邻板结构边界连续方程的基础上, 分别运用传递矩阵和Bloch定理建立了有限和无限周期复合板的耦合运动方程, 并详细对比分析了有限和无限周期复合板带隙衰减特性的关联关系.研究表明: 周期板结构的振动带隙频率范围与激励方式和激励位置是相关的, 若周期复合板在宽度方向按某阶模态进行线激励, 则该激励下的振动带隙与无限周期复合板在该阶模态下的振动带隙是一致的; 若周期板在点激励作用, 则该点激励下的振动带隙是参与振动的各阶模态振动带隙的交集. 此外, 还进一步研究了结构阻尼对振动衰减带隙的影响. 关键词： 周期复合板 带隙衰减特性 波传播法 结构阻尼     

Three-mode coupling in a passive dielectric waveguide with index modulation

The characteristics of a three-mode coupling in a passive dielectric waveguide are investigated for the case of even TE modes. The index is assumed to have a doubly periodic harmonic variation in the propagation direction. By a singular perturbation procedure using multiple space scales, the coupled-mode equations governing the Bragg interactions are systematically deduced. The three-mode coupling causes a stop band in frequency and the characteristics of the resulting evanescent mode are analyzed. For a periodic dielectric waveguide of finite length, the three coupled-mode equations are solved subject to suitable boundary conditions to obtain the reflection and the transmission coefficients. The frequency response of the reflection and the transmission coefficients are investigated and compared with the results of the pair of corresponding two-mode couplings. Representative numerical results are presented to illustrate the characteristics of the interaction of the three modes.     

Wave localization on a submerged cylindrical shell with rib aperiodicity

The results of a numerical study of vibration localization due to stiffener variability in a framed shell are reported. An axisymmetric finite element (FE)-infinite element model is used to obtain predictions in good general agreement with previously reported experimental results. Over the frequency band of this study, up to three times the ring frequency, two structural resonances dominate the vibratory response of the shell for high circumferential orders (n > 10). Localization is shown to be linked to the sensitivity of the local resonance frequencies of the system to specific geometrical parameters. Specifically, rib thickness variations strongly affect the first pass band, while rib spacing variations strongly affect the second pass band.     

Theoretical and experimental investigations of flexural wave propagation in periodic grid structures designed with the idea of phononic crystals

The propagation characteristics of flexural waves in periodic grid structures designed with the idea of phononic crystals are investigated by combining the Bloch theorem with the finite element method. This combined analysis yields phase constant surfaces, which predict the location and the extension of band gaps, as well as the directions and the regions of wave propagation at assigned frequencies. The predictions are validated by computation and experimental analysis of the harmonic responses of a finite structure with 11× 11 unit cells. The flexural wave is localized at the point of excitation in band gaps, while the directional behaviour occurs at particular frequencies in pass bands. These studies provide guidelines to designing periodic structures for vibration attenuation.     

Propagation of acoustic waves in a fluid-filled pipe with periodic elastic Helmholtz resonators

Helmholtz resonators are widely used to reduce noise in a fluid-filled pipe system. It is a challenge to obtain lowfrequency and broadband attenuation with a small sized cavity. In this paper, the propagation of acoustic waves in a fluid-filled pipe system with periodic elastic Helmholtz resonators is studied theoretically. The resonance frequency and sound transmission loss of one unit are analyzed to validate the correctness of simplified acoustic impedance. The band structure of infinite periodic cells and sound transmission loss of finite periodic cells are calculated by the transfer matrix method and finite element software. The effects of several parameters on band gap and sound transmission loss are probed.Further, the negative bulk modulus of periodic cells with elastic Helmholtz resonators is analyzed. Numerical results show that the acoustic propagation properties in the periodic pipe, such as low frequency, broadband sound transmission, can be improved.     

Coupled flexural-torsional vibration band gap in periodic beam including warping effect

The propagation of coupled flexural-torsional vibration in the periodic beam including warping effect is investigated with the transfer matrix theory. The band structures of the periodic beam, both including warping effect and ignoring warping effect, are obtained. The frequency response function of the finite periodic beams is simulated with finite element method, which shows large vibration attenuation in the frequency range of the gap as expected. The effect of warping stiffness on the band structure is studied and it is concluded that substantial error can be produced in high frequency range if the effect is ignored. The result including warping effect agrees quite well with the simulated result.     

Design and optimization of periodic structure mechanical filter in suppression of foundation resonances

The paper describes the development of periodic structure mechanical filter (PSMF) that has the potential to reduce vibration transmission and sound radiation at resonances of the foundation in a two-degree-of-freedom (2dof) vibration isolation system by using the band gaps of the periodic structure. The transmission matrix method is used to model vibration transmission of the 2dof system and an analytical expression of sound radiation from the foundation plate is derived. The multi-layer PSMF composed of rigid plates and curved beams is represented by an equivalent m-k-c (viscous damping) model. The propagation/attenuation zones and attenuation ability of PSMF are expressed in the propagation scenario and the iso-attenuation curves by exploiting the unit cell transfer matrix invariant. Influence of the number of unit cells, viscous damping on the mobility of PSMF and vibro-acoustic behavior of the 2dof system is extensively studied. And under the constraints of installation space and stability of the whole system, the more the number of the unit cells, the better attenuation ability in the band gap can be obtained. The interaction between PSMF and the 2dof system is analyzed by the substructure method and contribution of frequency component from different substructures is identified by setting different level of damping for each substructure. Factors influencing the first mounting frequency of the 2dof system with PSMF are discussed and three styles of installing PSMF are studied. The performance of piecewise periodic PSMF and quasi-periodic PSMF is also studied in an attempt to eliminate new-born resonances by PSMF. An optimization scheme involving sensitivity analysis is applied to obtain the optimal values of m and k. And the optimization is effective. The experiment of detecting the band gap of PSMF and the comparative trial of a 2dof system with a flexible plate as the foundation with/without PSMF are carried out. Both numerical and experimental simulation results have demonstrated that by use of PSMF, the vibration transmission at resonances is reduced and the radiation of the foundation at resonances is suppressed.