表面活性剂辅助合成CdWO4纳米棒和纳米线

以Na₂WO₄•2H₂O和CdCl₂ 为主要原料, 分别在十六烷基三甲基溴化铵(CTAB)和十二烷基苯磺酸钠(SDBS)表面活性剂中, 在180 ℃反应16 h, 水热制备了CdWO₄纳米棒和纳米线. 利用X射线粉末衍射(XRD)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段对产物进行了表征, 并对其在室温下的发光特性进行了测定. 实验结果表明: 产物均为具有单斜结构的单相CdWO₄. 其中CdWO₄纳米棒具有单晶属性, 平均粒径约为63 nm, 长度近1 µm; 而CdWO₄纳米线具有多晶特性, 平均粒径约为12 nm, 长度达十几微米. 当激发波长为253 nm时均有460 nm强的发射峰, 其中CdWO₄单晶纳米棒的发光强度大于CdWO₄多晶纳米线. 分别对CdWO₄纳米棒和纳米线形成的可能机理进行了初步分析.     

表面活性剂辅助合成CdWO4纳米棒和纳米线

以Na₂WO₄•2H₂O和CdCl₂ 为主要原料, 分别在十六烷基三甲基溴化铵(CTAB)和十二烷基苯磺酸钠(SDBS)表面活性剂中, 在180 ℃反应16 h, 水热制备了CdWO₄纳米棒和纳米线. 利用X射线粉末衍射(XRD)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)等手段对产物进行了表征, 并对其在室温下的发光特性进行了测定. 实验结果表明: 产物均为具有单斜结构的单相CdWO₄. 其中CdWO₄纳米棒具有单晶属性, 平均粒径约为63 nm, 长度近1 µm; 而CdWO₄纳米线具有多晶特性, 平均粒径约为12 nm, 长度达十几微米. 当激发波长为253 nm时均有460 nm强的发射峰, 其中CdWO₄单晶纳米棒的发光强度大于CdWO₄多晶纳米线. 分别对CdWO₄纳米棒和纳米线形成的可能机理进行了初步分析.     

高质量NaNdF4六方棱柱纳米棒的水热形貌控制合成及发光性质

采用水热法在温和的条件下合成了具有规则外形的六方棱柱状NaNdF₄纳米棒。X射线衍射（XRD）分析表明：产物为纯六方相NaNdF₄,场发射扫描电镜（SEM）分析表明产物形貌为棱柱状纳米棒,长约为550nm,棒的端部呈规则六边形,边长约为85nm。高分辨透射电子显微镜（HRTEM）和选区电子衍射（SD）显示所得样品为良好的单晶。NaNdF₄晶体的生长动力学过程表明：螯合剂（EDTA-Na₂）与稀土金属离子间的螯合作用受pH值影响,导致成核速度变化,进而影响NaNdF₄纳米晶的最终尺寸和形貌。室温下的NaNdF₄纳米棒的发光峰位于红外光范围（λ=892,1058,和1342nm）,其最强发射峰位于1058nm,对应于Nd³⁺的⁴F_3/2→⁴I_11/2f-f跃迁。     

一维Bi2Fe4O9纳米棒阵列的无模板水热合成

以物质的量的比为1：1的Bi（NO₃）₃·5H₂O和Fe（NO₃）₃·9H₂O为反应原料,以NaOH为矿化剂,利用水热法在Ti基板上成功制备出一维Bi₂Fe₄O₉纳米棒阵列。对该纳米棒阵列分别进行XRD、FE-SEM、HR-TEM和UV-Vis测试,得到Bi₂Fe₄O₉纳米棒的直径为100nm,长度为3~4μm,并表现出良好的光吸收性能,禁带宽度约为1.9eV,对甲基紫溶液的光降解率达到86%,其活性明显高于市售P25（TiO₂）。该纳米棒阵列的生长方式完全遵循奥斯瓦尔德熟化（Ostwald ripening）单晶生长机理。     

不同形貌纳米CoWO4的水热法制备及气敏性能

以Co（NO₃）₂·6H₂O、Na₂WO₄·2H₂O为主要原料,去离子水为溶剂,利用水热法在不同条件下制备了一系列的纳米CoWO₄,用XRD、TEM和比表面分析仪对产品的物相、形貌和比表面积进行了表征。较系统地探讨了水热条件（反应混合物pH值、反应时间、反应温度等）对产物物相和形貌的影响,并研究了不同形貌产品对甲醛、乙醇、氨气、苯和丙酮等的敏感性能。结果表明：水热条件对产品的物相和形貌有影响,在不同水热条件下,可成功制备CoWO₄纳米颗粒、纳米立方体及纳米棒;以纳米颗粒、纳米立方体及纳米棒样品制成的气敏元件对被试气体有不同程度的响应,其中以纳米颗粒为基的元件在210℃对1000μL·L^-1NH₃灵敏度为3.3。     

SiO2/Co3O4核壳催化剂对AP热分解的催化性能研究

采用改良的Stöber法制备粒径约为200 nm的单分散球形SiO₂颗粒,以此为内核,分别通过液相沉淀法和尿素均匀沉淀法制备包覆形式不同的新型SiO₂/Co₃O₄核壳式纳米催化剂。采用X-射线衍射分析(XRD)、透射电子显微镜(TEM)、红外光谱分析(IR)、拉曼光谱分析(Raman)、BET比表面积测试等手段对产物进行表征,利用差式扫描量热仪(DSC)考察SiO₂/Co₃O₄复合物对高氯酸铵(AP)热分解反应的催化作用,探讨不同包覆形式对其催化活性的影响。结果表明,两种方法制备得到的SiO₂/Co₃O₄复合物分别为层包覆和粒子包覆,比表面积大,具有明显的核壳结构,且粒子包覆形式的SiO₂/Co₃O₄对AP热分解反应的催化效果最好,使AP的高温分解温度降低了110 ℃,放热量增加了662 J·g^-1。     

水热法制备Sb2S3纳米棒有序阵列

以Sb(S₂CNEt₂)₃为单源前驱体，通过改变时间、温度、表面活性剂等反应条件，用水热法成功合成了各种尺寸的Sb₂S₃纳米棒及其有序阵列。X-射线衍射(XRD)、能量分散光谱(EDS)以及选区电子衍射(SAED)研究表明纳米棒由正交晶系Sb₂S₃单晶构成。扫描电子显微镜(SEM)和透射电子显微镜(TEM)研究显示Sb₂S     

等离子体修饰磁载TiO2光催化剂性能研究

以化学共沉法制备的CoFe₂O₄纳米粒子为磁核,采用TiCl₄水解包覆技术制备磁载二氧化钛纳米复合粒子CoFe₂O₄ /TiO_x(TCF),利用低温等离子体技术修饰TCF制备了CoFe₂O₄/TiO₂(PTCF)纳米复合光催化剂。运用VSM(振动样品磁强计)技术对样品磁性能进行研究,结果表明：等离子体修饰后的复合材料仍具有较高的饱和磁化强度,可在外加磁场作用下实现催化剂在水中的分离与回收;样品的XRD、TEM和UV-Vis分析测试结果表明：等离子体修饰后的复合材料有锐钛矿型TiO₂存在;TEM谱图显示磁核CoFe₂O₄的平均粒径约为20 nm,TCF复合粒子的粒径约为30~40 nm,TiO₂包覆层的厚度为10~20 nm。与纯TiO₂相比PTCF样品对光的吸收拓展到整个紫外-可见区,扩大了光谱响应范围;对甲基橙溶液降解的光催化活性评价研究表明：TCF复合粒子等离子体修饰后的PTCF纳米复合光催剂的光催化活性明显提高。     

焙烧温度对In2TiO5纳米带晶型结构及光催化性能的影响

以Ti(OC₄H₉)₄、In(NO₃)₃和聚乙烯吡咯烷酮(PVP-K30)为原料,采用静电纺丝技术制备了In₂TiO₅纳米带。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见漫反射光谱(UV-Vis DRS)和N₂吸附-脱附等技术对不同焙烧温度处理得到的样品进行表征,详细研究了焙烧温度对In₂TiO₅纳米带晶粒尺寸、形貌、比表面积和孔径的影响。以20 mg·L^-1的氟喹诺酮类抗生素左氧氟沙星(LEV)为目标降解物,125 W高压汞灯为光源,评价了不同焙烧温度下In₂TiO₅纳米带的光催化活性。结果表明,焙烧温度对In₂TiO₅的形貌与光催化活性有明显影响。当焙烧温度为800℃时,制备的In₂TiO₅纳米带表面光滑,其宽度为(552±58) nm、厚度约为140 nm,光催化活性最强,光照60 min,LEV的降解率可以达到95%。     

焙烧温度对In2TiO5纳米带晶型结构及光催化性能的影响

以Ti(OC₄H₉)₄、In(NO₃)₃和聚乙烯吡咯烷酮(PVP-K30)为原料,采用静电纺丝技术制备了In₂TiO₅纳米带。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见漫反射光谱(UV-Vis DRS)和N₂吸附-脱附等技术对不同焙烧温度处理得到的样品进行表征,详细研究了焙烧温度对In₂TiO₅纳米带晶粒尺寸、形貌、比表面积和孔径的影响。以20 mg·L^-1的氟喹诺酮类抗生素左氧氟沙星(LEV)为目标降解物,125 W高压汞灯为光源,评价了不同焙烧温度下In₂TiO₅纳米带的光催化活性。结果表明,焙烧温度对In₂TiO₅的形貌与光催化活性有明显影响。当焙烧温度为800℃时,制备的In₂TiO₅纳米带表面光滑,其宽度为(552±58) nm、厚度约为140 nm,光催化活性最强,光照60 min,LEV的降解率可以达到95%。     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

Microstructures of Some Bi-W-Nb-O Phases

Microstructures of three Bi-W-Nb-O phases have been examined by using high-resolution transmission electron microscopy. Bi₁₇W₂Nb₃O₃₉ and Bi₁₇WNb₃O₃₆ have incommensurate superstructures derived from the defect fluorite-type δ-Bi₂O₃ and can be regarded as intermediate phases between the type II solid solutions in the Bi-Nb-O and Bi-W-O systems. Bi₈W₂Nb₂O₂₃ has a Bi₂WO₆-like subunit cell with a stepped superstructure. Formation mechanisms of various superstructures are discussed.     

Reactivity of Binary Mixtures of La(III) Oxide and Cu(II) Oxalate or Nitrate and Synthesis of La(III) Cuprate

Reactivity of mixtures of La(III) oxide and Cu(II) oxalate/nitrate in hydrated as well as anhydrous state was studied using TG, DTA and XRD. Cu(II) oxide formed in the endothermic decomposition of mixture containing hydrated Cu(II) nitrate and La(III) oxide could not form La₂CuO₄ while Cu(II) oxide formed in the exothermic decomposition of mixture containing hydrated/anhydrous Cu(II) oxalate and La(III) oxide reacts with La(III) oxide and develops the phases CuLaO₃ and La₂CuO₄. The maximum reactivity with respect to the formation of La₂CuO₄phase was observed in mixture containing anhydrous Cu(II) oxalate. This revised version was published online in July 2006 with corrections to the Cover Date.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.     

电感耦合等离子体光谱法测定铜冶炼烟尘中锌

本实验介绍了电感耦合等离子体光谱法测定铜冶炼烟尘中锌含量的分析方法。针对样品碳,硅含量高的特点,有针对性的研究了样品的消解方法,确定采用盐酸、硝酸、氢氟酸、高氯酸对铜冶炼烟尘样品进行消解。同时进行了干扰试验,确定样品中高含量的铜,铅,砷等对样品测定结果没有影响。并对仪器的工作参数进行了优化。方法检出限为为0.011 mg/L,测定下限为0.019 mg/L,3个样品的相对标准偏差在0.54%~0.92%之间,加标回收率在96%~101.14%之间。该方法样品消解完全,流程短,操作简单,快速,测定准确度高,可以满足铜冶炼烟尘中锌含量的测定。     

α-Fe2O3掺杂对In2O3电导和气敏性能的影响

用化学共沉淀法制备了α Fe2O3掺杂的In2O3纳米晶微粉,研究了α Fe2O3掺杂对In2O3电导和气敏性能的影响. 结果表明, α Fe2O3和In2O3间可形成有限固溶体In2－xFexO3(0≤x≤0.40); Fe3＋对In2O3晶格中In3＋格位的部分取代,大大增强了阴阳离子间的结合力,导致材料中氧空位VO×数骤降、 自由电子的浓度变稀和电导下降. n(Fe3＋):n(In3＋)=5 :5的共沉淀粉于800 ℃下灼烧4 h所得的α Fe2O3掺杂In2O3传感器元件,对45 μmol•L－1 C2H5OH的灵敏度达54.0,为相同浓度干扰气体汽油的8倍多.     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

Reactivity of Zn3V2O8 Towards ZnMoO4 in the Solid State

The reactivity of Zn₃ V₂ O₈ towards ZnMoO₄ was investigated by using DTA and XRD methods. A new compound of the formula Zn_2.5 VMoO₈ was found. It crystallises in an orthorhombic system. The melting temperature was determinated to be 845±5°C. This revised version was published online in August 2006 with corrections to the Cover Date.     

Near infrared study of aqueous lanthanide perchlorates

The near infrared spectra of water in aqueous solutions of La(ClO₄)₃, Pr(ClO₄)₃, Nd(ClO₄)₃, Gd(ClO₄)₃, Er(ClO₄)₃, Yb(ClO₄)₃, Lu(ClO₄)₃, and NaClO₄ have been measured in the concentration range from 0.3 to 2.5 mol-dm^–3, at 25°C. The relative contents of free OH groups in the 1.0, 1.6, and 2.2M solutions have been calculated from extinction coefficients for water at 1160 nm. They increase with increasing salt concentration and are greater in solutions of the lighter lanthanide perchlorates at any fixed molarity. The results are discussed in terms of the stoichiometry and structure of hydrated cations of trivalent lanthanides.