Hydrobromination of residual vinyl groups on divinylbenzene polymer particles followed by atom transfer radical surface graft polymerization

Rigid and monodisperse spherical polymer particles with 2.36 ± 0.18 μm diameter containing residual surface vinyl groups were prepared by photoinitiated precipitation polymerization of divinylbenzene. Anti‐Markovnikov addition of HBr to the surface vinyl groups yielded a 2‐bromoethyl functionality that was used as macroinitiator for atom transfer radical polymerization (ATRP), providing the possibility for further functionalization by controlled “grafting from” processes. This was demonstrated by grafting of glycidyl methacrylate brushes from the particle surface, using an ATRP system based on CuBr and pentamethyl diethylenetriamine. Existence of a methacrylic overlayer was verified by FTIR and XPS measurements, and the grafted particles were easily dispersed in water, confirming conversion of the particle surface from hydrophobic to hydrophilic. Hydrobromination of residual vinyl groups yields a macroinitiator that can be used for grafting of glycidyl methacrylate by ATRP. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1259–1265, 2009     

Grafting of polymers onto and/or from silica surface during the polymerization of vinyl monomers in the presence of γ‐ray‐irradiated silica

The effects of radicals on silica surface, which were formed by γ‐ray irradiation, on the polymerization of vinyl monomers were investigated. It was found that the polymerization of styrene was remarkably retarded in the presence of γ‐ray‐irradiated silica above 60 °C, at which thermal polymerization of styrene is readily initiated. During the polymerization, a part of polystyrene formed was grafted onto the silica surface but percentage of grafting was very small. On the other hand, no retardation of the polymerization of styrene was observed in the presence of γ‐ray‐irradiated silica below 50 °C; the polymerization tends to accelerate and polystyrene was grafted onto the silica surface. Poly(vinyl acetate) and poly(methyl methacrylate) (MMA) were also grafted onto the surface during the polymerization in the presence of γ‐ray‐irradiated silica. The grafting of polymers onto the silica surface was confirmed by thermal decomposition GC‐MS. It was considered that at lower temperature, the grafting based on the propagation of polystyrene from surface radical (“grafting from” mechanism) preferentially proceeded. On the contrary, at higher temperature, the coupling reaction of propagating polymer radicals with surface radicals (“grafting onto” mechanism) proceeded to give relatively higher molecular weight polymer‐grafted silica. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2972–2979, 2006     

Encapsulation of silica nanoparticles by redox-initiated graft polymerization from the surface of silica nanoparticles

This study describes a facile and versatile method for preparing polymer-encapsulated silica particles by ‘grafting from’ polymerization initiated by a redox system comprising ceric ion (Ce⁴⁺) as an oxidant and an organic reductant immobilized on the surface of silica nanoparticles. The silica nanoparticles were firstly modified by 3-aminopropyltriethoxysilane, then reacted with poly(ethylene glycol) acrylate through the Michael addition reaction, so that hydroxyl-terminated poly(ethylene glycol) (PEG) were covalently attached onto the nanoparticle surface and worked as the reductant. Poly(methyl methacrylate) (PMMA), a common hydrophobic polymer, and poly(N-isopropylacrylamide) (PNIPAAm), a thermosensitive polymer, were successfully grafted onto the surface of silica nanoparticles by ‘grafting from’ polymerization initiated by the redox reaction of Ce⁴⁺ with PEG on the silica surface in acid aqueous solutions. The polymer-encapsulated silica nanoparticles (referred to as silica@PMMA and silica@PNIPAAm, respectively) were characterized by infrared spectroscopy, thermogravimetric analysis, and transmission electron microscopy. On the contrary, graft polymerization did not occur on bare silica nanoparticles. In addition, during polymerization, sediments were observed for PMMA and for PNIPAAm at a polymerization temperature above its low critical solution temperature (LCST). But the silica@PNIPAAm particles obtained at a polymerization temperature below the LCST can suspend stably in water throughout the polymerization process.     

Functional colloidal particles stabilized by layered silicate with hydrophilic face and hydrophobic polymer brushes

In this study, we describe a new strategy for producing narrowly dispersed functional colloidal particles stabilized by a nanocomposite with hydrophilic clay faces and hydrophobic polystyrene (PS) brushes on the edges. This method involves preparation of polymer brushes on the edges of clay layers and Pickering suspension polymerization of styrene in the presence of the nanocomposites. PS brushes on the edges of clay layers were prepared by atom transfer radical polymerization. X‐ray diffraction and thermogravimetric analysis results indicated that PS chains were grafted to the edges of clay platelets. Transmission electron microscope results showed that different morphologies of clay‐PS particles could be obtained in different solvents. In water, clay‐PS particles aggregated together, in which PS chains collapsed forming nanosized hydrophobic domains and hydrophilic clay faces stayed in aqueous phase. In toluene, clay‐PS particles formed face‐to‐face structure. Narrowly dispersed PS colloidal particles stabilized by clay‐PS were prepared by suspension polymerization. Because of the negatively charged clay particles on the surface, the zeta potential of the PS colloidal particles was negative. Positively charged poly(2‐vinyl pyridine) (P2VP) chains were adsorbed to the surface of PS colloidal particles in aqueous solution at a low pH value, and gold nanoparticles were prepared in P2VP brushes. Such colloidal particles may find important applications in a variety of fields including waterborne adhesives, paints, catalysis of chemical reactions, and protein separation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1535–1543, 2009     

Atom transfer radical polymerization of n‐butyl acrylate from silica nanoparticles

This article reports the synthesis of atom transfer radical polymerization (ATRP) of active initiators from well‐defined silica nanoparticles and the use of these ATRP initiators in the grafting of poly(n‐butyl acrylate) from the silica particle surface. ATRP does not require difficult synthetic conditions, and the process can be carried out in standard solvents in which the nanoparticles are suspended. This “grafting from” method ensures the covalent binding of all polymer chains to the nanoparticles because polymerization is initiated from moieties previously bound to the surface. Model reactions were first carried out to account for possible polymerization in diluted conditions as it was required to ensure the suspension stability. The use of n‐butyl acrylate as the monomer permits one to obtain nanocomposites with a hard core and a soft shell where film formation is facilitated. Characterization of the polymer‐grafted silica was done from NMR and Fourier transform infrared spectroscopies, dynamic light scattering, and DSC. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4294–4301, 2001     

Synthesis,characterization, and micellization of PCL‐g‐PEG copolymers by combination of ROP and “Click” chemistry via “Graft onto” method

Biodegradable and biocompatible PCL‐g‐PEG amphiphilic graft copolymers were prepared by combination of ROP and “click” chemistry via “graft onto” method under mild conditions. First, chloro‐functionalized poly(ε‐caprolactone) (PCL‐Cl) was synthesized by the ring‐opening copolymerization of ε‐caprolactone (CL) and α‐chloro‐ε‐caprolactone (CCL) employing scandium triflate as high‐efficient catalyst with near 100% monomer conversion. Second, the chloro groups of PCL‐Cl were quantitatively converted into azide form by NaN₃. Finally, copper(I)‐catalyzed cycloaddition reaction was carried out between azide‐functionalized PCL (PCL‐N₃) and alkyne‐terminated poly(ethylene glycol) (A‐PEG) to give PCL‐g‐PEG amphiphilic graft copolymers. The composition and the graft architecture of the copolymers were characterized by ¹H NMR, FTIR, and GPC analyses. These amphiphilic graft copolymers could self‐assemble into sphere‐like aggregates in aqueous solution with diverse diameters, which decreased with the increasing of grafting density. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Grafting of poly(ε‐caprolactone) onto maghemite nanoparticles

We report the coating of maghemite (γ‐Fe₂O₃) nanoparticles with poly(ε‐caprolactone) (PCL) through a covalent grafting to technique. ω‐Hydroxy‐PCL was first synthesized by the ring‐opening polymerization of ε‐caprolactone with aluminum isopropoxide and benzyl alcohol as a catalytic system. The hydroxy end groups of PCL were then derivatized with 3‐isocyanatopropyltriethoxysilane in the presence of tetraoctyltin. The triethoxysilane‐functionalized PCL macromolecules were finally allowed to react on the surface of maghemite nanoparticles. The composite nanoparticles were characterized by diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). Effects of the polymer molar mass and concentration on the amount of polymer grafted to the surface were investigated. Typical grafting densities up to 3 μmol of polymer chains per m² of maghemite surface were obtained with this grafting to technique. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6011–6020, 2004     

Effect of molecular weight on synthesis and surface morphology of high-density poly(ethylene glycol) grafted layers

This work describes studying the permanent grafting of carboxylic acid end-functionalized poly(ethylene glycol) methyl ether (PEG) chains of different molecular weights from the melt onto a surface employing poly(glycidyl methacrylate) ultrathin film as an anchoring layer. The grafting led to the synthesis of the complete PEG brushes possessing exceptionally high grafting density. The maximum thickness of the attached PEG films was strongly dependent on the length of the polymer chains being grafted. The maximum grafting efficiency was close to the critical entanglement molecular weight region for PEG. All grafted PEG layers were in the "brush regime", since the distance between grafting sites for the layers was lower than the end-to-end distance for the anchored macromolecules. Scanning probe microscopy revealed that the grafting process led to complete PEG layers with surface smoothness on a nanometric scale. Practically all samples were partly or fully covered with crystalline domains that disappeared when samples were scanned under water. Due to the PEG hydrophilic nature, the surface with the grafted layer exhibited a low (up to 21 degrees ) water contact angle.     

Synthesis of colloidal superparamagnetic nanocomposites by grafting poly(ϵ‐caprolactone) from the surface of organosilane‐modified maghemite nanoparticles

Superparamagnetic and biodegradable/biocompatible core–corona nanocomposite particles were prepared by ring‐opening polymerization of ?‐caprolactone initiated from the surface of maghemite. As was done in a previous work, an aminosilane coupling agent was chosen as the coinitiator and immobilized at the surface of the maghemite particles to allow the growth of the poly(?‐caprolactone) (PCL) chains from the solid surface. Two different catalytic systems based on aluminum and tin alkoxides were investigated. Whatever the catalyst used, diffuse reflectance Fourier transform spectroscopy brought evidence for polymer anchoring through a covalent bond, whereas thermogravimetric analysis attested to the presence of high amounts of PCL around the maghemite. Magnetization measurements proved that the nanocomposites kept their superparamagnetic properties after coating. The polymer contents obtained by this grafting‐from route were compared with the results obtained by a more classical grafting‐to process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3221–3231, 2005     

Multiple levels hydrophobic modification of polymeric substrates by UV‐grafting polymerization with TFEMA as monomer

The hydrophobic solid surface modification with fluorine‐containing monomers has received tremendous attention because of its unique structure and excellent property. However, these hydrophobic films normally suffer from two major problems: one is weak interface interaction between fluoropolymers and substrates, and the other is the high cost of fluorine‐containing monomers. Herein, with the aim of feasible industrial application, a facile in situ UV photo‐grafting method is reported, which could ensure the formation of chemical bonds between fluoropolymer‐grafted layer and substrate with a low cost commercial 2,2,2‐trifluoroethyl methacrylate (TFEMA) as monomer. With low‐density polyethylene (LDPE) film as a model substrate, four kinds of poly‐TFEMA‐grafted layer are fabricated on LDPE films with different surface morphologies: polymer brush, polymer network, crosslinked nanoparticles, and a micro‐ and nanoscale hierarchical structure. The experimental results showed that the water contact angles (CAs) of the LDPE films grafted with polymer brush, polymer network, and crosslinked nanoparticles were (103 ± 2)°, (95 ± 2)°, and (122 ± 2)°, respectively, which were much higher than that of LDPE film. The introduction of micro‐ and nanoscale hierarchical structures can dramatically improve the surface roughness, which will further enhance the film hydrophobicity, and the water CA can reach as high as (140 ± 1)°. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1059–1067     

High density cationic polymer brushes from combined “click chemistry” and RAFT‐mediated polymerization

A simple method for preparing cationic poly[(ar‐vinylbenzyl)trimethylammonium chloride)] [poly(VBTAC)] brushes was used by combined technology of “click chemistry” and reversible addition‐fragmentation chain transfer (RAFT) polymerization. Initially, silicon surfaces were modified with RAFT chain transfer agent by using a click reaction involving an azide‐modified silicon wafer and alkyne‐terminated 4‐cyanopentanoic acid dithiobenzoate (CPAD). A series of poly(VBTAC) brushes on silicon surface with different molecular weights, thicknesses, and grafting densities were then synthesized by RAFT‐mediated polymerization from the surface immobilized CPAD. The immobilization of CPAD on the silicon wafer and the subsequent polymer formation were characterized by X‐ray photoelectron spectroscopy, water contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, atomic force microscopy, and ellipsometry analysis. The addition of free CPAD was required for the formation of well‐defined polymer brushes, which subsequently resulted in the presence of free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. In addition, by varying the polymerization time, we were able to obtain poly(VBTAC) brushes with grafting density up to 0.78 chains/nm² with homogeneous distributions of apparent needle‐like structures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Facile preparation of superhydrophobic and oleophobic surfaces via the combination of Cu(0)‐mediated reversible‐deactivation radical polymerization and click chemistry

The fabrication of novel hydrophobic, superhydrophobic, and oleophobic surfaces on glass using nanosilica particles modified with polymer brushes prepared via surface initiated Cu(0)‐mediated reversible‐deactivation radical polymerization was demonstrated. Monomers including n‐butyl acrylate, 2,2,2‐trifluoroethyl methacrylate, and 1,1,1,3,3,3‐hexafluoroisopropyl acrylate were used to synthesize a series of nanosilica–polymer organic/inorganic hybrid materials. Products were analyzed using infrared spectroscopy, thermogravimetric analysis, scanning and transmission electron microscopy. The coated nanosilica showed core–shell structures that contains polymer brushes up to 67 wt %. The application of these particles for modifying surface wettability was examined by covalently attaching them to glass via a recently developed one‐pot “grafting to” methodology using “thio‐bromo click” chemistry. Atomic force microscopy topographic images show up to 25 times increase in roughness of the coated glass compared to blank glass sample. Contact angle measurements showed that nanosilica coated with PBA and PTFEM produced hydrophobic glass surfaces, while a superhydrophobic and oleophobic surface was generated using nanosilica functionalized with PHFIPA. This novel methodology can produce superhydrophobic and oleophobic surfaces in an easy and fast way without the need for tedious and time‐consuming processes, such as layer‐by‐layer deposition, high temperature calcination, and fluorinated oil infusion. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018     

Tuning the low critical solution temperature of polymer brushes grafted on single‐walled carbon nanotubes and temperature dependent loading and release properties

A nondestructive method was developed for grafting and retrieving polymer brushes from single‐walled carbon nanotubes (SWCNT)s based on mussel‐inspired chemistry. Thermo‐responsive polymer brushes were grafted on SWCNTs by coating the tubes with polydopamine as a reactive underlayer and sequential surface‐initiated atom transfer radical polymerization of oligo(ethylene glycol) methacrylate (OEGMA, M_n = 475) and 2‐(2'‐methoxyethoxy)ethyl methacrylate (MEO2MA). Copolymer brushes were retrieved from the SWCNTs using 1 M NaOH to destroy the crosslinked polydopamine coating, and after that, the pristine properties of the SWCNTs were preserved. The low critical solution temperature (LCST) and molecular weight of the copolymer were measured using a nephelometer and gel permeation chromatograph, respectively. The loading and release behavior of Rhodamine 6G on responsive polymer‐grafted SWCNTs demonstrates that the copolymer brushes confer the SWCNTs an LCST dependence. This method can accurately confirm the molecular weights and polydispersity of stimuli‐responsive polymers grafted on any other nanoparticles and predict their controlled release behavior. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1807–1814     

Ring‐opening polymerization of ε‐caprolactone and L‐lactide from silica nanoparticles surface

Coating of silica nanoparticles by biocompatible and biodegradable polymers of ε‐caprolactone and L ‐lactide was performed in situ by ring‐opening polymerization of the cyclic monomers with aluminum, yttrium, and tin alkoxides as catalysts. Hydroxyl groups were introduced on the silica surface by grafting of a prehydrolyzed 3‐glycidoxypropyl trimethoxysilane to initiate a catalytic polymerization in the presence of metal alkoxides. In this manner, free polymer chains were formed to grafted ones, and the graft density was controlled by the nature of the metal and the alcohol‐to‐metal ratio. The grafting reaction was extensively characterized by spectroscopic techniques and quantified. Nanocomposites containing up to 96% of polymer were obtained by this technique. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1976–1984, 2004     

The preparation and characterization of carboxylic acid‐coated silica nanoparticles

The preparation of carboxylic acid‐coated silica nanoparticles was investigated. A monolayer of carboxylic acid residues with controllable graft density was anchored to the nanoparticle by a ring‐opening reaction with succinic anhydride. Poly(methacrylic acid) [poly(MAA)] grafted nanoparticles were prepared via a polymerization–deprotection strategy. Tert‐butyl methacrylate was polymerized from the surface of silica nanoparticles in a predictable manner and with excellent control over the molecular weight distribution. Subsequent removal of the tert‐butyl group resulted in poly (MAA) grafted nanoparticles. The polymer nanoparticles were also functionalized with dyes, which may be useful in tracking the particles in biological systems. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Mean‐field theoretical analysis of brush‐coated nanoparticle dispersion in polymer matrices

The equilibrium dispersion of nanoparticles with grafted polymer chains into polymer matrices, of the same chemical structure as the brush, is studied through the device of mean‐field theory. Our results show that the disperion of brush‐coated nanoparticles into a matrix polymer is improved with (i) decreasing particle radius and (ii) increasing brush chain length. Both of these aspects can be understood based on the fact that, unlike the case of planar surfaces, homopolymer chains end‐grafted to spherical nanoparticle surfaces tangentially spread away from the surface thus alleviating the packing frustration that is created by the relatively high grafting densities. This permits significant brush/matrix overlap, even at high grafting densities, a regime that has only recently become experimentally available due to advances in polymer synthesis (i.e., the “grafting‐to” methods). © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 351–358, 2008     

双分布聚乙二醇接枝纳米二氧化硅的高效可控制备

在混合溶剂中通过"grafting to"的方法将2种分子量不同的聚乙二醇单甲醚(MPEG M_w=750,4000)接枝到氨基修饰的St?ber法二氧化硅(SiO_2-NH_2)表面,制备双分布纳米接枝复合物.采用二步法,先将带环氧端基的低分子量聚乙二醇单甲醚(MPEG-EO)与SiO_2-NH_2在甲苯溶剂中充分反应后,与高分子量的MPEG-EO在甲苯和正癸烷的混合溶剂中使用相同的反应条件和后处理方法,能便捷制备出具有双分布接枝的纳米复合物.在接枝反应体系中,分子链的链段尺寸和接枝密度之间存在着密切关系.一定的范围内,接枝密度随链段尺寸减小而增大.通过改变混合溶剂比例来调控接枝链段的尺寸,可以很好控制聚合物的接枝密度.在双分布接枝的纳米复合物中,低分子量的接枝密度为0.85 chains/nm~2,高分子量的接枝密度能达到0.40 chains/nm~2,体现出了简单、高效、可控的特点,与聚环氧乙烷(PEO)共混后分散良好,对于制备出均匀分散的纳米复合材料起到了一定的指导作用.     

结构规整的高密度两亲性接枝聚合物刷的合成及其自组装研究

大分子单体通过两种可控聚合方法, 即开环易位聚合(ROMP)和原子转移自由基聚合(ATRP)的联用, 合成一种新型两亲性接枝聚合物刷. 具有高环张力的降冰片烯单侧链大分子单体norbornene-graft-poly(ε-caprolactone)/Br (PCL- NBE-Br)首先进行ROMP反应, 生成聚合物主链, 每个单体单元上含有一条PCL链和一个溴官能团; 然后用含溴的ROMP聚合物poly(norbornene)-graft-poly(ε-caprolactone)/Br (PCL-PNBE-Br)作为大分子引发剂引发单体2-(dimethyl- amino)ethyl methacrylate)的ATRP反应, 生成结构明确的高密度两亲性接枝聚合物刷poly(norbornene)-graft-poly(ε- caprolactone)/poly(2-(dimethylamino)ethyl methacrylate) (PCL-PNBE-PDMAEMA), 其主链每个单体单元上均含有一条疏水性PCL接枝链和一条亲水性PDMAEMA接枝链. 最后, 研究此类高密度两亲性接枝聚合物刷的自组装行为, 用动态激光光散射(DLS)研究其在混合溶剂(THF/H2O)中的胶束行为, 考察胶束溶液的浓度以及不同长度的亲水性接枝链对胶束尺寸的影响; 利用透射电镜(TEM)观察胶束为球形, 具有类似线团或草莓状的形态.     

PS/PMMA mixed polymer brushes on the surface of clay layers: Preparation and application in polymer blends

Polystyrene (PS) and poly(methyl methacrylate) (PMMA) mixed polymer brushes on the surface of clay layers were prepared by using in situ free radical polymerization. Free radical initiator molecules with two quaternary ammonium groups at both ends were intercalated into the interlayer spacing of clay layers. The amount of polymer brushes grafted on the surface of clay layers can be controlled by controlling the polymerization time. Thermogravimetric analysis, X‐ray diffraction, and high‐resolution transmission electron microscope results indicated successful preparation of the mixed polymer brushes on the surface of clay layers. The kinetics of the grafting of the monomers was also studied. The mixed polymer brushes on the surface of clay layers were used as compatibilizers in blends of PS and PMMA. In the blends, the intercalated clay particles tend to locate at the interface of two phases reducing the interfacial tension. In the meanwhile, PMMA homopolymer chains tend to intercalate into clay layers. The driving force for the intercalation is the compatibility between homo‐PMMA chains and PMMA brushes on the surface of clay layers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5329–5338, 2007     

Tethered nanoparticle-polymer composites: phase stability and curvature

Phase behavior of poly(ethylene glycol) (PEG) tethered silica nanoparticles dispersed in PEG hosts is investigated using small-angle X-ray scattering. Phase separation in dispersions of densely grafted nanoparticles is found to display strikingly different small-angle X-ray scattering signatures in comparison to phase-separated composites comprised of bare or sparsely grafted nanoparticles. A general diagram for the dispersion state and phase stability of polymer tethered nanoparticle-polymer composites incorporating results from this as well as various other contemporary studies is presented. We show that in the range of moderate to high grafting densities the dispersion state of nanoparticles in composites is largely insensitive to the grafting density of the tethered chains and chemistry of the polymer host. Instead, the ratio of the particle diameter to the size of the tethered chain and the ratio of the molecular weights of the host and tethered polymer chains (P/N) are shown to play a dominant role. Additionally, we find that well-functionalized nanoparticles form stable dispersions in their polymer host beyond the P/N limit that demarcates the wetting/dewetting transition in polymer brushes on flat substrates interacting with polymer melts. A general strategy for achieving uniform nanoparticle dispersion in polymers is proposed.