新型水溶性共轭嵌段含糖聚合物的合成与表征

以两端溴化的聚9,9-二己基芴作为大分子引发剂, 6-O-甲基丙烯酰基-1,2∶3,4-二-O-异亚丙基-D-吡喃型半乳糖(6-O-Methacryloyl-1,2∶3,4-di-O-isopropylidene-D-galactopyranose, MaIpGa)为单体, 氯化亚铜/1,1,4,7,10,10-六甲基三乙基四胺为催化剂, 通过原子转移自由基聚合(ATRP), 合成了一种新型的具有良好光学性能的三嵌段共聚物聚甲基丙烯酸羟基保护半乳糖酯-聚芴-聚甲基丙烯酸羟基保护半乳糖酯(PMaIpGa-PF-PMaIpGa). 在酸性条件下进一步水解, 得到水溶性的聚甲基丙烯酸半乳糖酯-聚芴-聚甲基丙烯酸半乳糖酯(PMaGa-PF-PMaGa)三嵌段聚合物, 其结构和分子量(分布)通过核磁共振、红外光谱和凝胶渗透色谱(GPC)确证, 并研究了其紫外-可见和荧光光谱特性.     

含联芴烯单元共轭聚合物的合成及表征

以六羰基钨[W(CO)₆]为催化剂, 合成了聚吲哚芴(P1)、 聚梯型四苯(P2)、 聚梯型五苯(P3)和小分子9-联吲哚芴烯(S1).该类聚合物的重复单元含有联芴烯结构, 通过芴9位的双键连接. 光学和电化学等实验结果表明, 聚合物无荧光发射, 是一类窄带隙的共轭聚合物, 其中聚合物P1薄膜的紫外吸收值最大波长为710 nm.     

苯乙炔悬挂取代的热致交联型芴-三苯胺交替聚合物的合成与表征

通过Suzuki偶合反应合成出由苯乙炔悬挂取代的芴-三苯胺类交替共轭聚合物聚(9,9-二辛基-2,7-芴-共-N-4-苯乙炔-4,4'-三苯胺)(PFT-PE),并通过NMR和FT-IR对其化学结构进行了表征。结果表明:该聚合物易溶于常用的有机溶剂,可通过溶液旋涂的方式进行薄膜制备。由PFT-PE薄膜的吸收起始波长可知其光学带宽为2.82 eV。其薄膜较溶液态的荧光光谱发生了显著的红移并且变宽,说明在固态下聚合物分子链间发生了一定的堆积。由其电化学起始氧化电位可知PFT-PE的最高能量占有轨道能级(HOMO)为-5.39 eV,其氧化过程具有高度的可逆性,说明该聚合物具有良好的电化学稳定性。悬挂炔键功能团的存在使得该聚合物无需外加引发剂即可在一定温度下发生分子间的交联反应。     

主链含有非共轭结构的聚芴类蓝光聚合物的合成与性能研究

通过Suzuki偶合反应合成出了主链中含有非共轭烷氧基组分(-O-CH2-CH2-CH2-CH2-O-)的聚芴类衍生物聚- 2,7-(9,9-二辛基芴)-co-4,4’-丁氧基二苯(PFP)和聚-2,7-(9,9-二辛基芴)-co-4,4’-丁氧基二苯-co-N-苯基-4,4’-二苯胺(PFTP11)并通过相同的条件合成出主链由芴和三苯胺交替相连的聚合物聚-2,7-(9,9-二辛基芴)-co-N-苯基-4,4’-二苯胺(PFTPA)作为参比材料. 通过1H NMR和FT-IR分析对这些聚合物的化学结构进行了表征. 这三种聚合物在常用的有机溶剂中具有很好的溶解性, 可通过溶液加工的方式制备聚合物薄膜. 这些聚合物均具有较高的热分解温度(＞400 ℃), 聚合物PFP具有较高的玻璃化转变温度(～130 ℃)而PFTP11和PFTPA则未出现明显的玻璃化转变过程. 通过对聚合物的吸收特性进行测试得知它们具有较大的光学带宽(2.89～3.29 eV). 所有聚合物在固体薄膜状态下均发射出蓝色荧光, PFP, PFTP11和PFTPA的最大PL发射分别位于425, 437和440 nm. 通过对其电化学性能进行测试可知由于三苯胺基团的引入聚合物的HOMO能级明显提高, 这意味着聚合物的空穴传输能力得到了有效的改善.     

芴酮对聚醚侧链聚芴体系的影响: 合成, 表征及光物理性质的研究

利用Yamamoto聚合反应, 通过调节单体2,7-二溴9,9'-二-(三乙氧基甲基)芴和2,7-二溴芴酮的比例, 合成了侧链为极性聚醚链, 芴酮含量逐渐增加的聚芴系列. 通过聚合物溶液及固态薄膜的紫外荧光谱图, 深入研究芴酮作为能量受体的能量转移过程及其对聚合物光物理性质的影响. 结果表明: 稀溶液中体系呈现聚芴本征态的荧光发射, 能量转移对溶液浓度具有依赖性; 固态薄膜中能量转移效率随芴酮含量的增加而快速增长, 退火后这种现象更加明显.     

非共价键自组装制备聚对苯撑乙炔/聚丙烯酸水溶性荧光纳米粒子及其光物理行为研究

通过功能化聚对苯撑乙炔(含羟基与氨基)和聚丙烯酸之间的非共价键自组装制备了一系列含共轭聚合物的水溶性荧光纳米粒子, 并进行了相关结构和光学性质表征. 研究表明, 纳米粒子的大小和聚丙烯酸/聚对苯撑乙炔质量比直接相关. 光物理性质研究表明, 形成水溶性纳米粒子后, 疏水的聚苯撑乙炔链在纳米粒子中易于形成π-链间聚集, 其光物理性质与其在薄膜态时相似.     

绿色单峰发光聚(9,9-二烯丙基芴)的合成及其发光机制

为了得到绿色单峰发光的聚合物材料, 我们设计并合成了9位取代的二烯丙基芴单体, 在NiCl₂的催化下, 合成了可溶的聚芴衍生物, 聚(9,9-二烯丙基芴)(PAF). 较短的烯丙基链既可以增加聚芴的溶解度, 双键的存在又有利于聚芴发生分子间聚集而得到绿光发射的有机电致发光器件(OLED). PAF在溶液和薄膜状态下的荧光峰分别位于403和456 nm的蓝光区域, 而其器件ITO/PEDOT:PSS/PAF/LiF/Al(其中, ITO为氧化铟锡, PEDOT为聚(3,4-乙撑二氧噻吩), PSS为聚苯乙烯磺酸盐)的电致发光峰却红移至绿光区域(532 nm), 得到绿色单峰发光. 紫外吸收光谱、荧光发射光谱、红外光谱以及原子力显微镜(AFM)图像的结果证明, 造成PAF电致发绿光的机制为聚合物分子间聚集.     

一锅法制备pH响应性聚丙烯酰基乙二胺盐酸盐-卟啉/芴荧光聚合物

采用可逆加成-断裂链转移聚合法(RAFT)制备了含有双硫酯片段的聚N-叔丁基氧羰基-丙烯酰基乙二胺(PBAEN).利用一锅法制备出含卟啉(EPT)或芴(DEPF)单元的PBAEN.经脱保护反应得到水溶性聚丙烯酰基乙二胺盐酸盐-卟啉(PAEN-EPT)和聚丙烯酰基乙二胺盐酸盐-芴(PAEN-DEPF).PAEN-EPT和PAENDEPF具有良好的水溶性,其中PAEN-EPT的荧光量子产率达0.097.当溶液pH≥7时,PAEN-EPT和PAEN-DEPF均出现荧光猝灭现象.PAEN-EPT和PAEN-DEPF的pH响应行为使得该类聚合物在水溶性荧光探针领域具有潜在的应用前景.     

树枝化对聚芴类分子发光行为的影响

运用稳态吸收、稳态荧光光谱及皮秒时间分辨荧光光谱等手段, 研究了树枝化对聚芴分子的光谱动力学行为的影响. 在1×10-5 mol/L四氢呋喃溶液中, 非树枝化聚芴和不同代数的树枝化聚芴的稳态吸收和稳态荧光光谱基本一致, 表明树枝化不影响聚芴基团的本征电子性质; 在薄膜状态下, 紧密排列的聚芴分子表现出明显的链间聚集行为. 不同代数树枝化聚芴的时间分辨荧光动力学研究结果表明, 溶液状态下的发光为单指数衰减行为, 而薄膜状态下的发光为多指数衰减行为, 且其发光寿命随树枝化代数增加而增长, 表明树枝化基团抑制了邻近的聚芴分子之间能量传递所致的激发态能量耗散.     

聚芴类共轭聚合物(PFs)从溶液到薄膜凝聚态演变过程中的定量构效关系

聚芴（polyfluorenes，PFs）是一类具有高荧光效率和良好热稳定性的经典蓝光共轭聚合物.本研究组近年来集中于聚芴类共轭聚合物溶液中单链构象-聚集态结构-薄膜凝聚态结构-器件性能间的定量构效关系研究，利用静/动联用激光光散射等表征手段，结合标度率研究方法，对PFs成膜前体溶液复杂的单链和聚集的形态结构进行了系统的研究.结合光谱与电镜等方法，揭示出PFs在溶液中孤立单链、凝聚态结构、β构象及其过渡态结构形成的动力学过程、机理及规律，构建出成膜前体溶液单链构象-薄膜中链构象-器件性能之间的定量构效关系.旨在从高分子本征性质入手，提高其光电效率.本研究不仅对聚芴类高分子，而且对整个共轭聚合物类材料的设计与加工都将具有重要的指导意义.     

丙烯酸接枝邻苯二酚衍生物的二次聚合

合成了2种聚合前驱体邻苯二丙烯酸酯(o-PDA)和2-甲氧基苯丙烯酸酯(2-MOPA), 分别通过与丙烯酸(AA)自由基共聚得到邻苯二丙烯酸酯-丙烯酸共聚物(O1)和2-甲氧基苯丙烯酸酯-丙烯酸共聚物(O2). 产物邻苯二酚(o-DHB)-O1(质量比1∶1)和1-羟基-2-甲氧基苯(HMOB)-O2(质量比1∶1)分别在乙腈/二氯甲烷-三氟化硼乙醚体系中直接阳极氧化聚合获得交联网状共聚物P1和P2. P1和P2均可溶于DMSO, 而难溶于ACN, DCM和THF等有机溶剂. 通过UV-Vis, FTIR和 ¹H NMR对交联共聚物膜的结构进行了表征. AA的引入不仅可以增加链的柔韧性, 而且提高了共聚物的力学性能. 而o-DHB/ HMOB的引入极大地减弱了单体的聚合位阻, 实现了单体的二次聚合, 同时也增强了单体及聚合物的电化学活性. 荧光光谱显示, 得到的2种交联共聚物膜分别在415和487 nm处有较强的发射峰, 表明共聚物仍具有良好的蓝色发光性能, 且聚丙烯酸结构的引入并没有对聚邻苯二酚(Po-DHB)和聚(1-羟基-2-甲氧基苯)(PHMOB)产生较大的荧光猝灭作用. 热重分析曲线(TGA)表明2种交联共聚物膜均具有较高的热稳定性.     

三氟化硼乙醚溶液中卤代芴的电化学聚合

在三氟化硼乙醚(BFEE)溶液中9-溴芴和9,9-二氯芴可以直接阳极氧化制备聚(9-溴芴)和聚(9,9-二氯芴).单体在BFEE中的起始氧化电位远低于在乙腈体系中的起始氧化电位.聚(9-溴芴)和聚(9,9-二氯芴)均可溶于强极性有机溶剂,如二甲基亚砜、四氢呋喃等,并分别表现出良好的蓝色和黄绿色发光性能,其电导率测定为10-1S/cm.红外光谱和核磁共振波谱表明聚合反应主要发生在2,7位.     

Sulfophthalide cycle cleavage and formation of fluorenyl structures upon poly(diphenylene sulfophthalide) thermolysis

Thermolysis of poly(diphenylene sulfophthalide) (PDSP) in the temperature range from 100 to 500 °C was studied by IR and UV-Vis spectroscopy and thermogravimetric analysis. A series of absorption bands in the IR spectrum of PDSP were assigned on the basis of the theoretical calculations of the IR spectrum of diphenyl sulfophthalide used as a model compound, in particular, ν_as(S=O) = 1352 cm^?1, ν_s(S=O) = 1196 cm^?1, ν(C-O) ～ 920 cm^?1, ν(S-O) = 824 cm^?1, and δ(SO₂) = 576 cm^?1. The sulfophthalide cycle (SPC) in PDSP decomposes at the thermolysis temperatures in a range of 260–400 °C. An analysis of the IR spectra of the thermolyzate and the quantum chemical calculations of the IR spectra of the model compounds confirmed the predominant formation of fluorenyl structures in the thermolyzed polymer. The changes in the UV-Vis spectra observed upon the thermolysis of thin films of PDSP (the hypsochromic shift of the long-wavelength absorption band from 271 to 263 nm and the appearance a shoulder at ～310 nm) and the results of TD-DFT calculations of the UV-Vis spectra of the model compounds are consistent with the hypothesis about the formation of fluorenyl structures. The general scheme of PDSP thermolysis at 260–400 °C was proposed in which the major process is the formation of fluorenyl fragments in macromolecules of the polymer due to the intramolecular ring closure in biradicals formed by the SPC cleavage.     

一种新的光致变色膜：Na2WO4-PAA-Glycerol体系研究

A method for preparing Na₂WO₄-PAA-Glycerol photochromic films was reported. The film was composed of Na₂WO₄, PAA and Glycerol, which were coated on a glass substrate. The film turned blue in the sun, and bleached to transparent in the darkness. The UV-Visible spectra showed strong absorbance at 300～500 nm, and the ABS changed signifanctly at 500～800 nm. The film showed the best photochromic behavior when n_Na2WO4∶n_PAA is 4%～5%. The mechanism was suggested that after irradiation, poly tunstate produced by Na₂WO₄ and PAA formed the tungsten blues. The tungsten blues were bleached due to oxidation back to poly tunstate by oxygen. The film showed not only an excellent photochromism property with rapid response and good reversibility, but also the simple techniques and good stability.     

一种耐高温聚噻吩膜的电化学合成

聚噻吩及其衍生物具有高的电导率、良好的环境稳定性以及易于调控的分子链结构,因此一直受到人们的广泛关注．但是,这类材料的耐温性能较差,从而将影响其在有机电子器件中的应用．     

Poly(methyl acrylate)/poly(hydroxyethyl acrylate) sequential interpenetrating polymer networks. Miscibility and water sorption behavior

Sequential poly(methyl acrylate)/poly(hydroxyethyl acrylate) interpenetrating polymer networks with different poly(hydroxyethyl acrylate) contents were prepared by free radical polymerization of hydroxyethyl acrylate inside the previously polymerized poly(methyl acrylate) network. Differential scanning calorimetry on dry samples shows that the interpenetrating polymer networks exhibit phase separation, and no differences are found between the glass transition temperatures of the two phases present in the interpenetrating polymer network and those of the pure components. Thermally stimulated depolarization current experiments were used to study the influence of water sorption on the mobility of the different molecular groups in the poly(hydroxyethyl acrylate) phase of the interpenetrating polymer network. Isothermal water sorption of the interpenetrating polymer networks and pure poly(methyl acrylate) and poly(hydroxyethyl acrylate) networks is analyzed with different theories to compare the behavior of the poly(hydroxyethyl acrylate) phase in the interpenetrating polymer networks with that of the pure poly(hydroxyethyl acrylate) network. Diffusion coefficients of water in the interpenetrating polymer networks are obtained by means of dynamic sorption experiments. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1587–1599, 1999     

Cellulose Nano Whiskers (CNWs) Loaded-Poly(sodium acrylate) Hydrogels. Part-I. Effect of Low Concentration of CNWs on Water Uptake

In this work, de-watered cellulose pulp(DCP), obtained from a paper mill, have been acid-hydrolyzed to yield cellulose nano-whiskers (CNWs). As revealed from FESEM measurements, these CNW were found to possess a median length of 258.5 nm, diameter of 35.2 nm, and an aspect ratio of 7.3. The CNWs were also characterized by TGA, XRD and FTIR analysis. The CNWs were found to possess a fairly high Crystallinity Index (CI) of 0.925. The addition of cellulose at low concentration range, i.e., from 25 to 125 mg (nearly 1.25 to 6.25 weight percent of polymer sodium acrylate) caused an enhancement in water uptake of resulting hydrogels .The CNWs-loaded poly(SA) hydrogels showed chain relaxation controlled swelling in the medium of pH 7.4 as was confirmed from the swelling exponent ‘n’ values obtained using power function law‥ The second order kinetic model was found to fit well to the kinetic water uptake data. However, all the samples, when prepared in the form of films, did not show any remarkable increase in their mechanical strength.     

Synthesis and characterization of poly (n-butyl acrylate)-poly (methyl methacrylate) latex interpenetrating polymer networks by radiation-induced seeded emulsion polymerization

A series of latex interpenetrating polymer networks (LIPNs) were prepared via a two-stage emulsion polymerization of methyl methacrylate (MMA) or mixture of MMA and n-butyl acrylate (n-BA) on crosslinked poly(n-butyl acrylate)(PBA) seed latex using ⁶⁰Co γ-ray radiation. The particles of resultant latex were produced with diameters between 150 and 250 nm. FTIR spectra identified the formation of crosslinked copolymers of PMMA or P(MMA-co-BA). Dynamic light scattering (DLS) showed that with increasing n-BA concentration in second-stage monomers, the particle size of LIPN increased. Transmission electron microscope(TEM) photographs showed that the morphology of resultant acrylate interpenetrating polymer network (IPN) latex varied from the distinct core-shell structure to homogenous particle structure with the increase of n-BA concentration, and the morphology was mainly controlled by the miscibility between crosslinked PBA seed and second-stage copolymers and polarity of P(MMA-co-BA)copolymers. In addition, differential scanning calorimeter (DSC) measurements indicated the existence of reinforced miscibility between PBA seed and P(MMA-co-BA)copolymer in prepared LIPNs.     

Polyurethane acrylate-stabilized cholesteric liquid crystal dispersions

Polymer stabilized cholesteric liquid crystals (PSCLCs) have been fabricated based on various structures of polyurethane acrylate (PUA) as well as conventional acrylate polymer, namely poly(1,6-hexanediol diacrylate). For PUA stabilized films, the transmittance spectra of cured films were essentially identical to those of uncured films, with no 'dead' reaction; whereas, using acrylate polymer; reflection greatly decreased upon curing and showed significant 'dead' reaction after the cessations of irradiation. The structure of PUA also had significant effects on the electro-optic performance, and these effects are interpreted in terms of elasticity and interfacial interaction between the polymer and LC.     

Studies on Synthesis and Effect of Dopants on Conductivity and Morphology of Organically Soluble Poly(o-anisidine)

Synthesis of poly(o-anisidine) doped with various protonic acids by using ammonium persulphate as oxidizing agent were carried out in aqueous acid media. Influences of protonic acids on the physicochemical properties were investigated. The various process parameters were optimized to obtain poly(o-anisidine) in the conducting salt phase form. The results are discussed with references to different protonic acids. It was observed that poly(o-anisidine) is highly soluble in organic solvents, such as m-cresol and N-methyl pyrrolidinone (NMP). The polymers were characterized by UV-Visible, FTIR, SEM, XRD and conductivity measurements. A result shows that, different types of dopant acids HCl, H₂SO₄ and HClO₄ affect the morphology and electrical conductivity of the polymer. The electrical conductivity of the polymer follows the order HCl >H₂SO₄>HClO₄. Thus the effect of dopant ion type and the size of its negative ions influence the physico-chemical properties. UV-Vis absorption spectra shows peaks at 740–783 nm with shoulder at 380–420 nm as characteristic peaks for the emeraldine salt (ES) phase of poly(o-anisidine) POA. The FTIR spectra show a broad and intense band at ～2800–3001 cm^?1 and ～1159–1170 cm^?1 that account for the formation of ES phase of the polymer. The X-ray diffraction spectra show a characteristic peak at 20–30^o, 2θ range which reveals partial crystalline structure. The conductivity of the poly(o-anisidne) salt was found to be in the range of 10^?3 to 10^?2 S/cm. SEM studies of poly(o-anisidine) doped with HCl shows the continuous granular uniform morphology with sub-micrometer evenly distributed particles of size ～100–200 nm.