铁钴双金属催化剂上二氧化碳加氢合成低碳烯烃

研究了常压下铁钴双金属催化剂上二氧化碳催化加氢合成低碳烯烃的反应,考察了钴含量、反应温度对二氧化碳转化率、产物选择性的影响。结果表明,钴的添加有利于铁的碳化,提高了二氧化碳转化率,降低了一氧化碳选择性,提高了甲烷选择性,适量钴的添加促进了二氧化碳向烃的转化。在铁钴摩尔比６７∶３３,反应温度３５０℃,反应空速５０００ｍｌｇ－１ｈ－１条件下,二氧化碳转化率达到２８１％,Ｃ＋２选择性达到１１６％,烯烷比５     

Reduction Characteristics of Carbon Dioxide Using a Plasmatron

To decompose carbon dioxide, which is a representative greenhouse gas, a 3-phase gliding arc plasmatron device was designed and manufactured to examine the decomposition of CO₂, either alone or in the presence of methane with and without water vapour. The changes in the amount of carbon dioxide feed rate, the methane to carbon dioxide ratio, the steam to carbon dioxide ratio, and the methane to steam ratio were used as the parameters. The carbon dioxide conversion rate, energy decomposition efficiency (EDE), carbon monoxide and hydrogen selectivity, and produced gas concentration were also investigated. The maximum values of the carbon dioxide conversion rate, which is a key indicator of carbon dioxide decomposition, in different cases were compared. The maximum carbon dioxide conversion rate was 12.3 % when pure carbon dioxide was supplied; 34.5 % when methane was injected as a reforming additive; 7.8 % when steam was injected as a reforming additive; and 43 % when methane and steam were injected together. Therefore, this could be explained that the methane-and-steam injection showed the highest carbon dioxide decomposition, showing low EDE as 0.01 L/min W. Furthermore, the plasma produced carbon-black was compared with commercial carbon-black chemicals through Raman spectroscopy, surface area measurement and scanning electron microscopy. It was found that the carbon-black that was produced in this study has the high conductivity and large specific surface area. Our product makes it suitable for special electric materials and secondary battery materials applications.     

Optimization of equilibrium carbon dioxide methane reforming parameters by the Gibbs free energy minimization method

The thermodynamic equilibrium in the carbon dioxide conversion of methane is studied by Gibbs energy minimization. The curves that represent the dependences of the degree of coke formation, the content of methane and carbon dioxide in syngas, and the syngas module on the CO₂/CH₄ mole ratio in the initial mixture and on temperature at various pressures, are plotted. The regions in which the CO₂/CH₄ mole ratio is optimal for carbon dioxide conversion and no coke formation occurs, and which are characterized by a minimal content of methane and carbon dioxide in syngas, are revealed.     

甲烷氧化细菌催化二氧化碳生物合成甲醇的研究

甲烷氧化细菌中包含的甲烷单加氧酶(MMO)、甲醇脱氢酶(ADH)、甲醛脱氢酶(FaldDH)、甲酸脱氢酶(FateDH)经过一系列反应能够把甲烷深度氧化生成二氧化碳，并生成一定的能量物质．把二氧化碳还原为甲醇是一个需要能量的过程，目前还没有已知的有机体在温和条件下完成这一反应．研究发现，甲基弯菌Methylosi-nus trichosporium IMV 3011可以催化二氧化碳生物转化生成甲醇．在休眠的悬浮细胞中充人二氧化碳后，反应一段时间在反应液中检测到了甲醇．二氧化碳转化成甲醇是一个需要能量推动的反应，为了补充反应所消耗的能量．反应一段时间后需要用甲烷进行再生，以恢复细胞中的还原当量NADH．我们进行了反应再生的交替连续批式反应，甲醇积累量能够维持在一个比较稳定的水平．理论上，反应不会增加温室效应，这是一个有效的、环境友好的、可恢复的反应过程．     

流化床中 CH4/C3H8 自热重整制合成气

 在流化床反应器中, 考察了 Ni/SiO2 催化剂上 CH4 或 CH4-C3H8 临氧 CO2 重整 (自热重整) 制合成气反应性能. 结果表明, 在 CH4-C3H8 混合气自热重整反应中, Ni 粒径较小催化剂的活性和抗积炭性能较高, CH4 和 CO2 转化率分别达 75.5% 和 72.6%. C3H8 比 CH4 更易解离及被氧化, 部分 C3H8 解离出来的中间产物 CHx 物种可与吸附 H 结合为 CH4, 因而降低了 CH4 的表观转化率; CHx 也可与吸附的 CO2 物种反应生成 H2 与 CO, 从而促进了 CO2 的转化.     

Dilute Methane Treatment by Atmospheric Pressure Dielectric Barrier Discharge: Effects of Water Vapor

Oxidation of dilute methane in oxygen containing mixtures by atmospheric pressure dielectric barrier discharge at moderate temperature (below 150°C) has been studied with regard to the effect of water vapor. First, the impact of water vapor on methane conversion was studied in nitrogen. In dry nitrogen, methane was converted into hydrogen cyanide and hydrogen in the absence of oxidant. When water was added, it both acted as a scavenger in competition with methane for reactive nitrogen species and changed the reaction product speciation from HCN to carbon monoxide and carbon dioxide. The addition of water also led to the formation of hydrogen and nitrogen oxides. In the presence of oxygen, the addition of 1% water vapor enhanced methane conversion. Increasing water vapor content above 1% had a slight positive effect on methane conversion, and was found to enhance selectivity of the reaction products toward carbon dioxide over carbon monoxide.     

Methane Conversion to Higher Hydrocarbons in the Presence of Carbon Dioxide Using Dielectric-Barrier Discharge Plasmas

Experimental investigation has been conducted to convert methane into higher hydrocarbons in the presence of carbon dioxide within dielectric-barrier discharge (DBD) plasmas. The objectives of cofeed of carbon dioxide are to inhibit carbon deposit and to increase methane conversion. The products from this plasma methane conversion include: (1) syngas (H₂+CO), (2) gaseous hydrocarbons containing ethylene, acetylene, and propylene, (3) liquid hydrocarbons, (4) plasma-polymerized film, and (5) oxygenates. The selectivity of products is subject to the DBD plasma-reactive conditions and catalyst applied. The liquid hydrocarbons produced by this way are highly branched, which represents a better fuel production.     

Effect of Electrical Pulse Forms on the CO2 Reforming of Methane Using Atmospheric Dielectric Barrier Discharge

Methane conversion using an electric discharge has been studied for many years. Recently, many research groups have developed high-frequency pulsed plasma reaction for methane conversion to higher hydrocarbons and synthesis gas. CO₂ reforming of methane to synthesis gas has also attracted considerable interest as a method of utilization of the greenhouse gases, CO₂ and CH₄, which occupy most of man-made greenhouse gases. In this study, the influence of pulse form of applied voltage on methane and carbon dioxide conversions and product selectivity has been investigated using a cylindrical type DBD reactor. For this purpose, two kinds of power supply were compared, that is, AC power supply which has a high-frequency sinusoidal wave form, and AC pulse power supply which has modified AC pulse wave form. The conversions of methane and carbon dioxide were enhanced using pulsed plasma. The lower pulse width was more profitable economically.     

电中性团簇MCu2Ox(M=Cu2+,Ce4+,Zr4+)上甲烷和二氧化碳直接合成乙酸的理论研究

采用密度泛函理论(DFT)方法研究了电中性团簇MCu₂O_x(M=Cu²⁺, Ce⁴⁺, Zr⁴⁺; x=3, 4)的特性及其对甲烷和二氧化碳直接合成乙酸反应的影响. 结果表明, 团簇催化的反应由甲烷C—H活化、 二氧化碳插入引起C-C偶联、 CH₃COO转向和氢迁移4步构成. 前两步为关键步骤, C—H和C-C各自与团簇活性位点间形成四中心结构并推动反应进行. 电子自甲烷流出到团簇, 再流入二氧化碳, 使甲烷的C—H和二氧化碳的C=O得以活化, 继而驱动C-C偶联. Ce, Zr引入至氧化铜团簇中后, 团簇由原有的六元环结构衍变为六元环Ⅰ、 掺杂原子分别位于中心和端末的双四元环Ⅱ和Ⅲ 3种结构. 团簇结构和电子自旋均会影响反应的进行. 低自旋团簇有利于甲烷 C—H活化, 而高自旋团簇则有利于C-C偶联; 在3种掺杂团簇结构中, 处于三重态的结构Ⅲ团簇可以较好地兼顾C—H活化和C-C偶联. 通过比较相同结构发现, Ce, Zr掺杂调变了氧化铜团簇活性位点的局域电荷, 虽使其对甲烷C—H活化的能力略有下降, 但却显著降低了C-C偶联反应的活化自由能垒, 从而促进了反应的进行. 掺杂原子Zr的助剂作用比Ce要大.     

铜基催化剂上甲烷催化燃烧反应动力学特性研究

采用固定床微分反应器,在常压、450~500℃、甲烷体积分数10%~35%条件下,进行铜基催化剂上甲烷催化燃烧动力学特性研究。研究表明,甲烷分压对反应速率影响显著,而氧气分压的影响可以忽略。采用最小二乘法进行动力学模型参数估计,建立的反应动力学模型为-rCH4=1.61×107×e-108 000/RT×pCH40.5。检验结果表明,所建模型与实验数据良好相容,是适宜和可信的。根据实验结果推断甲烷催化燃烧分两步进行,首先氧气快速与铜基催化剂上活性空位点反应,形成吸附氧气分子;随后吸附氧气分子和甲烷分子反应,生成二氧化碳和水。     

Optimizing the parameters of the steam-carbon dioxide conversion of methane by Gibbs energy minimization

The thermodynamic equilibrium for the steam-carbon dioxide conversion of methane was studied by Gibbs energy minimization. The degree of coke formation, the content of methane and carbon dioxide in the synthesis gas, and the synthesis gas H₂/CO ratio were plotted as functions of the molar ratios of CO₂/CH₄ and H₂O/CH₄ in the initial mixture at different temperatures and pressures. The regions of the optimum CH₄/CO₂/H₂O molar ratios for steam-carbon dioxide conversion were discovered, with no coke formation taking place in these regions. The optimized CH₄/CO₂/H₂O molar fractions characterized by the minimum content of methane and carbon dioxide in the synthesis gas were found for each region.     

羟基磷灰石负载Ni催化剂中Ni含量对催化甲烷二氧化碳重整制合成气性能的影响

以低温沉淀方法制备的羟基磷灰石(HAp)为载体,采用浸渍法制备了一系列不同Ni含量的Ni/HAp催化剂,并采用BET、H2-TPR、XRD、SEM、FT-IR、TEM和TG-DTA技术对催化剂进行了表征。结果表明,NiO含量为13%的催化剂表现出最好的催化甲烷二氧化碳重整制合成气活性,在850℃、空速3.6×104mL/(h·gcat)的反应条件下,甲烷和二氧化碳的转化率在10 h内分别稳定在72%和83%。这主要归因于催化剂中金属和载体之间的强相互作用。虽然反应后的催化剂表面有少量的积炭,但这些积炭多以丝状炭存在,并不会影响催化剂的活性和稳定性。     

MCM-41 Supported Nickel Catalysts for Carbon Dioxide Reforming of Methane

There has been an increasing interest in the conversion of methane and carbon dioxide into synthesis gas^[1]. High performance Ni-based catalysts have attracted much attention^[2-4]. In this study, MCM-41 supported nickel were used as catalysts for carbon dioxide reforming of methane. It is found that the obtained catalyst exhibited high activity for getting syngas with its ratio of unity.In contrast to the performance of other nickel-based catalysts; Ni/MCM-41 has higher conversion and yield at lower temperature. The effects of nickel loading, particle size, GHSV, and calcination temperature on catalytic activities were also investigated.     

Conversion of Methane and Carbon Dioxide in a DBD Reactor: Influence of Oxygen

A continuous plug flow reactor supported by a dielectric barrier discharge (DBD) is used to study the conversion of methane, carbon dioxide, and oxygen at different compositions. The three studied gases were diluted with helium to 3 % with an overall flow rate of 200 sccm. The 13.56 MHz plasma was ignited at atmospheric pressure. The product stream and the inlet flow were analyzed by a FTIR spectrometer equipped with a White-cell and by a quadrupole mass spectrometer. The DBD reactor generates hydrogen, carbon monoxide, ethane, ethene, acetylene, formaldehyde, and methanol. Additional oxygen in the feed has positive effects on the yield of methanol, formaldehyde and carbon monoxide and reduces the total consumed energy. The hydrogen yield reaches its maximum at medium amounts of oxygen in the inlet flow. The conversion of methane increases to a limiting value of about 35 %. Methane rich feeds increase the yield of hydrogen, ethane and methanol. On the other hand, additional oxygen has a negative influence on the produced amount of C2 hydrocarbons. The conversion of methane and carbon dioxide as well as the yield of synthesis gas components and C2 hydrocarbons increases by changing the plasma power to higher values.     

Preparation of hydrogen for feeding fuel cells by low-temperature conversion of ethanol on Ni/ZnO and Ni-Cu/ZnO catalysts

Preparation of hydrogen by low-temperature steam conversion of ethanol on nickel and binary nickel-copper catalysts supported on zinc oxide was studied experimentally in the temperature interval 200–450°C. High efficiency of hydrogen evolution in the course of ethanol conversion on these catalysts was demonstrated. At temperatures lower than 350°C, the main conversion products are hydrogen, methane, carbon monoxide, and carbon dioxide. At 400°C, the conversion products contain no carbon monoxide, which allows the mixture obtained to be used for feeding fuel cells with proton-conducting membranes.     

Research On a Ceramics Membrane Reactor for Natural Gas Conversion

We explore the new concept for a ceramics membrane reactor including the investigation of the nickel-based catalysts for methane conversion into synthesis gas and the exploitation of an oxide ionic and electronic mixed conductor. When Ca_0.8Sr_0.2Ti_1−xFe_xO_3−α exhibiting the ionic and electronic mixed conduction was used as a support material of Ni based catalyst, coke formation over the catalyst under the methane conversion with air or carbon dioxide was strongly depended on the iron (III) ion contents, x. From the relationship between the amount of carbon deposited on the catalyst and the mixed conduction in support oxide materials, it was suggested that the self-migration of lattice oxygen inside the support regulated by the balance between the oxide ionic and electronic conductivities played an important role to prevent from accumulating the deposited carbon over the catalysts. In addition, we demonstrated the methane conversion into synthesis gas at 1173 K with one component ceramics membrane reactor constructed with the same type of perovskite-type oxide for both the catalyst supported and mixed conductor.     

Wet Conversion of Methane and Carbon Dioxide in a DBD Reactor

The influence of water on the plasma assisted conversion of methane and carbon dioxide in a dielectric barrier discharge (DBD) plug flow reactor was studied. The plasma at atmospheric pressure was ignited by a power supply at a frequency of 13.56?MHz. Product formation was studied at a power range between 35 and 70?W. The concentrations of the three gases were altered and diluted with helium to 3?%. FTIR spectroscopy and mass spectroscopy were applied to analyze the inlet and the product streams. The main product of this process are hydrogen, carbon monoxide and ethane. Ethene, ethine, methanol and formaldehyde are generated beside the main products in this DBD in lower concentrations. The conversion of methane, the ratio of the synthesis gas components (n(H₂):n(CO)), and the yield of oxygenated hydrocarbons and hydrogen increases by adding water. The total consumed energy reaches lower values for small amounts of water. Additional water does not influence the generated amount of C2 hydrocarbons and of CO, but decreases the carbon dioxide conversion.     

Effects of CO2 content on the activity and stability of nickel catalyst supported on mesoporous nanocrystalline zirconia

The effects of carbon dioxide content on the catalytic performance and coke formation of nickel catalyst supported on mesoporous nanocrystalline zirconia with high surface area and pure tetragonal crystalline phase were investigated in methane reforming with carbon dioxide. The samples were characterized by XRD, BET, TPR, TPO, TPH, TEM, and SEM techniques. The catalyst prepared showed high surface area and a mesoporous structure with a narrow pore size distribution. The obtained results revealed that the increase in CO2 content increased the methane conversion and stability of the catalyst and significantly reduced the coke deposition. The TPH analysis showed that several species of carbon with different reactivities toward hydrogenation were deposited on the spent catalysts employed under different CO2 contents.     

直接利用甲烷氧化偶联产物中的稀乙烯制环氧乙烷

直接利用甲烷氧化偶联产物中的稀乙烯制环氧乙烷刘育，徐法强，沈师孔（中国科学院兰州化学物理研究所，兰州，７３００００）关键词乙烯环氧化，甲烷氧化偶联，负载银催化剂１．前言甲烷氧化偶联（ＯＣＭ）是一个产物较为复杂的反应，从目前研究结果来看，产物中Ｃ２烃总...     

甲烷和二氧化碳在煤焦上反应制备合成气实验研究

以煤与甲烷共转化制备合成气的研究为背景,通过考察固定床反应器上甲烷和二氧化碳分别在石英砂、煤灰和煤焦上的反应过程,证实了煤焦中的碳结构在共转化过程中对甲烷转化具有催化作用。同时考察了反应温度（1073K～1223K）、CH₄/CO₂比（0.33~3.00）和气固接触时间等工艺条件对甲烷转化率、气相产物中H₂/CO比的影响。结果表明,甲烷的转化率随着反应温度和气固接触时间的增加而增大,随CH₄/CO₂比的增加而减小。在考察范围内甲烷的转化率最高达到了86%。反应物中CH₄/CO₂比的改变可以起到调节产品气中H₂/CO比的作用,0.4~2.0调节。